MODEL T28173/T28174
ROLLER TABLES
INSTRUCTIONS
FOR MODELS MFD. SINCE 10/17
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Rails
Figure 1. T28173/T28174 Roller Table features.
Rollers
Reversible Work Stop
T28174
T28173
Carriage
Adjustable
Legs & Feet
Introduction
The Model T28173/T28174 Roller Table (see
Figure 1) allow users to feed long material into a
workbench, saw, or other device across steel support rollers using a rail-mounted work-stop system
for repeatable cuts.
5
Support rollers are installed on 12
Adjustable legs and steel feet allow a working
height of 28" to 48".
The T28378 Slotted Mounting Plate (not included)
allows connection of the roller table to a machine
or workbench.
⁄8" centers.
A
B
DC E F G
Figure 2. T28173/T28174 inventory.
T28173 & T28174 Inventory
Description (Figure 2) Qty
A. Roller Table Assembly 78" (T28173) .......... 1
Roller Table Assembly 118" (T28174) ......... 1
B. Adjustable Leg Assemblies (T28173) ......... 2
Adjustable Leg Assemblies (T28174) ......... 3
C. Adjustable Handles 62L, M8-1.25 x 32 ...... 2
D. Hex Nuts M8-1.25 (T28173) ........................ 8
Hex Nuts M8-1.25 (T28174) ...................... 12
E. Flat Washers 8mm (T28173) ...................... 8
Flat Washers 8mm (T28174) .................... 12
F. Hex Bolts M8-1.25 x 16 (T28173) ............... 8
Hex Bolts M8-1.25 x 16 (T28174) ............. 12
G. Hex Wrench 6mm ....................................... 1
Specifications
Model Length Weight Capacity Rollers
T28173 78" 128 lbs. 1540 lbs. 7
T28174 118 " 154 lbs. 1540 lbs. 10
COPYRIGHT © JANUARY, 2018 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#KB19284 PRINTED IN CHINA
V1.0 1.18
Assembly
Items Needed Qty
Open-End Wrenches or Sockets 14mm ............ 2
Hex Wrench 6mm .............................................. 1
4 x 4 Blocks ....................................................... 2
Additional People .............................................. 2
To assemble roller table:
1. Place 4 x 4 blocks on floor positioned near
ends of roller table assembly, as shown in
Figure 3. The blocks will be used to keep
weight of table assembly off carriage.
4. Turn assembled roller table upright onto feet
(see Figure 5).
Figure 5. Leg assemblies attached to roller table
assembly (T28173 shown).
5. Final tighten hex nuts with wrench or socket.
Wood
Blocks
Figure 3. Use wood blocks to keep weight off
carriage during leg installation (T28173 shown).
2. With help from another person, turn roller
table assembly upside down, then place rails
on top of 4x4 blocks (see Figure 3).
3. Attach each leg assembly (2 for T28173, 3 for
T28174) to table assembly with (4) M8-1.25
x 16 hex bolts, (4) M8-1.25 hex nuts, and (4)
8mm flat washers per leg (see Figure 4).
Finger-tighten for now.
Carriage
Leg Assemblies
x 4
6. Install adjustable handles on carriage, as
shown in Figure 6.
Adjustable
Handles
Carriage
Figure 6. Adjustable handles installed on
carriage.
-2-
Figure 4. Attaching leg assemblies.
T28173/T28174 Roller Table (Mfd. 10/17)
Adjusting Roller Table Height & Level
Roller table height can be adjusted from 28" to 48"
by loosening (8) cap screws on each leg assembly to move the inner legs.
The feet can be adjusted to level the unit.
Carriage & Slide Bar
The slide bar/work stop is reversible and can be
positioned on either side of the carriage. Position
work stop in the "down" position to use it as a
push block, or place the work stop in the "up"
position to use the carriage as a primary stop.
Items Needed Qty
Hex Wrench 6mm .............................................. 1
Open-End Wrench 16mm .................................. 1
Open-End Wrench 24mm .................................. 1
Level .................................................................. 1
Additional People .............................................. 2
To adjust roller table height and level:
1. While assistants hold each end of roller table,
loosen (2) M16-1.5 hex nuts on bottom of
legs, then loosen (8) cap screws on each
leg assembly just until inner legs move freely
(see Figure 7).
Inner
Leg
x 8
To adjust slide bar and use work stop:
1. Lock carriage with adjustable handles, then
loosen (2) cap screws securing slide bar/
work stop to adjust slide bar/work stop position inside carriage mounting holes (see
Figure 8).
Cap
Screws
Carriage
Slide Bar
Positioning
Adjustable Handle
Figure 8. Carriage, work stop, and slide bar.
Work Stop
x 2
Adjustable Foot
Figure 7. Loosen cap screws to adjust leg
assembly height. Loosen hex nuts to adjust feet.
2. Adjust unit until it sits evenly on all legs. Set
roller table to desired height, then tighten cap
screws on each leg assembly.
3. Check and adjust level side to side and front
to back by adjusting feet as needed, then
tighten hex nuts on foot assemblies.
2. Position work stop in "down" position to use it
as a push block, or place stop in "up" position
to use carriage as primary stop.
3. Slide bar/work stop can be mounted in either
direction in either carriage mounting hole. To
remove slide bar/work stop, remove (2) cap
screws in carriage, as shown in Figure 9.
Remove
Cap Screws
Slide Bar
Mounting
Holes
T28173/T28174 Roller Table (Mfd. 10/17)
Figure 9. Repositioning or removing slide bar.
-3-
4. Place slide bar in other mounting hole and
secure with cap screws removed in Step 3
(see Figure 10).
Install
Cap
Screws
Install
Slide Bar
Mounting
Hole
Carriage
2. Insert T28378 slotted mounting plate between
leg assembly and roller table assembly, and
re-install (4) M8-1.25 x 16 hex bolts, (4)
M8-1.25 flange nuts, and (4) 8mm flat washers removed in Step 1.
3. Align roller table fitted with T28378 against
suitable workbench or machine. Adjust roller
table height if necessary, then use slots to
secure to machine (see Figure 12).
Note: If machine does not have existing
mounting holes, you will need to drill them
yourself.
Figure 10. Installing slide bar in carriage.
T28378 Slotted Mounting Plate
Use optional T28378 Slotted Mounting Plate to
connect the T28173 or T28174 to a workbench or
machine.
Items Needed Qty
Another Person .................................................. 1
T28378 Slotted Mounting Plate ......................... 1
Pencil or Permanent Marker .............................. 1
Drill with
To install and use T28378 slotted mounting
plate:
1. While an assistant holds end of roller table,
3
⁄8" Bit .................................................. 1
remove (4) M8-1.25 x 16 hex bolts, (4)
M8-1.25 flange nuts, and (4) 8mm flat washers securing leg assembly to roller table
assembly (see Figure 11).
To avoid machine damage and possible
electrocution/shock hazard, inspect workbench or machine to avoid drilling into wiring or important internal components.
Figure 12. Slots for mounting T28378 to
workbench or machine.
x 4
Slotted
Mounting
Plate
Leg
Assembly
Roller
Table
Assembly
Figure 11. Installing T28378 slotted mounting
plate.
-4-
4. Secure roller table with T28378 slotted mounting plate to workbench or machine using
5
appropriate length
⁄16" or 8mm hex bolts, hex
nuts and washers as needed.
T28173/T28174 Roller Table (Mfd. 10/17)
Please Note: We do our
best to stock replacement
parts whenever possible,
but we cannot guarantee
that all parts shown here
are available for purchase.
or
visit our online parts store
to
check for availability.
T28173 Parts
45
42
REF PART # DESCRIPTION REF PART # DESCRIPTION
11
30
Call (800) 523- 4777
52
11
33
34
15
12
10
40
38
37
36
41
39
35
43
44
22
46
47
48
49
4
2
5
3
1
31
51
16
50
54
6
53
19
7
9
8
13
14
18
NOTICE
DO NOT exceed maximum
weight capacity of 1540 lbs.
T28173
20
T28173
at www.grizzly.com
1 PT28173001 SIDE PLATE 78" 33 PT28173033 ROTATION LIMITING BLOCK
2 PT28173002 ROLLER 14-1/4" X 2-3/8" 34 PT28173034 WORK STOP
3 PT28173003 BALL BEARING 6003ZZ 35 PT28173035 ROLL PIN 8 X 50
4 PT28173004 CENTER SHAFT 36 PT28173036 SET SCREW M8-1.25 X 12
5 PT28173005 EXT RETAINING RING 17MM 37 PT28173037 INDICATOR
6 PT28173006 SUPPORT FRAME 38 PT28173038 CAP SCREW M4-.7 X 12
7 PT28173007 EXTENSION LEG 39 PT28173039 FLAT WASHER 4MM
8 PT28173008 ADJUSTABLE SCREW M16-1.5 X 50 40 PT28173040 FLAT WASHER 5MM
9 PT28173009 HEX NUT M16-1.5 41 PT28173041 CAP SCREW M5-.8 X 12
10 PT28173010 CAP SCREW M8-1.25 X 25 42 PT28173042 CAP SCREW M8-1.25 X 25
11 PT28173011 CAP SCREW M8-1.25 X 16 43 PT28173043 SLIDE BAR
12 PT28173012 HEX NUT M8-1.25 44 PT28173044 CARRIAGE
13 PT28173013 STEEL FOOT 80D M16-1.5 45 PT28173045 ADJUSTABLE HANDLE 63L, M8-1.25 X 32
14 PT28173014 EXT RETAINING RING 12MM 46 PT28173046 CAP SCREW M6-1 X 16
15 PT28173015 FLAT WASHER 8MM 47 PT28173047 FLAT WASHER 6MM
16 PT28173016 HEX NUT M12-1.75 48 PT28173048 SLIDING BLOCK
18 PT28173018 NOTICE LABEL 49 PT28173049 LIMITING BLOCK
19 PT28173019 QR CODE LABEL 50 PT28173050 HEX NUT M5-.8
20 PT28173020 MODEL NUMBER LABEL 51 PT28173051 BRACKET (RIGHT)
21 PT28173021 GRIZZLY.COM LABEL 52 PT28173052 SCALE 78"
22 PT28173022 TOUCH-UP PAINT, GRIZZLY GREEN 53 PT28173053 CAP SCREW M8-1.25 X 16
30 PT28173030 BRACKET (LEFT) 54 PT28173054 FENDER WASHER 8MM
31 PT28173031 SLIDE GUIDE
T28173/T28174 Roller Table (Mfd. 10/17)
BUY PARTS ONLINE AT GRIZZLY.CO M!
Scan QR code to visit our Parts Store.
grizzly.com
21
-5-
42
45
T28174 Parts
REF PART # DESCRIPTION REF PART # DESCRIPTION
11
53
54
31
22
30
33
52
10
38
39
36
38
37
35
34
43
48
46
47
41
40
44
49
5
3
4
2
11
16
50
1
51
19
6
15
12
7
18
NOTICE
DO NOT exceed maximum
weight capacity of 1540 lbs.
T28174
20
9
8
T28174
13
14
21
grizzly.com
1 PT28174001 SIDE PLATE 118" 33 PT28174033 ROTATION LIMITING BLOCK
2 PT28174002 ROLLER 14-1/4" X 2-3/8" 34 PT28174034 WORK STOP
3 PT28174003 BALL BEARING 6003ZZ 35 PT28174035 ROLL PIN 8 X 50
4 PT28174004 CENTER SHAFT 36 PT28174036 SET SCREW M8-1.25 X 12
5 PT28174005 EXT RETAINING RING 17MM 37 PT28174037 INDICATOR
6 PT28174006 SUPPORT FRAME 38 PT28174038 CAP SCREW M4-.7 X 12
7 PT28174007 EXTENSION LEG 39 PT28174039 FLAT WASHER 4MM
8 PT28174008 ADJUSTABLE SCREW M16-1.5 X 50 40 PT28174040 FLAT WASHER 5MM
9 PT28174009 HEX NUT M16-1.5 41 PT28174041 CAP SCREW M5-.8 X 12
10 PT28174010 CAP SCREW M8-1.25 X 25 42 PT28174042 CAP SCREW M8-1.25 X 25
11 PT28174011 HEX BOLT M8-1.25 X 16 43 PT28174043 SLIDE BAR
12 PT28174012 HEX NUT M8-1.25 44 PT28174044 CARRIAGE
13 PT28174013 FOOT 80D M16-1.5 45 PT28174045 ADJUSTABLE HANDLE 63L, M8-1.25 X 32
14 PT28174014 EXT RETAINING RING 12MM 46 PT28174046 CAP SCREW M6-1 X 16
15 PT28174015 FLAT WASHER 8MM 47 PT28174047 FLAT WASHER 6MM
16 PT28174016 FLANGE HEX NUT M12-1.75 48 PT28174048 SLIDING BLOCK
18 PT28174018 NOTICE LABEL 49 PT28174049 LIMITING BLOCK
19 PT28174019 QR CODE LABEL 50 PT28174050 HEX NUT M5-.8
20 PT28174020 MODEL NUMBER LABEL 51 PT28174051 BRACKET (RIGHT)
21 PT28174021 GRIZZLY.COM LABEL 52 PT28174052 SCALE 118"' LONG
22 PT28174022 TOUCH-UP PAINT, GRIZZLY GREEN 53 PT28174053 CAP SCREW M8-1.25 X 16
30 PT28174030 BRACKET (LEFT) 54 PT28174054 FENDER WASHER 8MM
31 PT28174031 SLIDE GUIDE
-6-
BUY PARTS ONLINE AT GRIZZLY.CO M!
Scan QR code to visit our Parts Store.
T28173/T28174 Roller Table (Mfd. 10/17)
Loading...