Grizzly T28062 Owner's Manual

COPYRIGHT © SEPTEMBER, 2017 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#ES19038 PRINTED IN JAPAN

MODEL T28062

HIGH-PRECISION

MINI ROTARY TOOL

OWNER'S MANUAL

(For models manufactured since 08/17)

V1. 0 9 .17

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre­hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip­ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Model T28062 (Mfd. Since 08/17) -1-

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazard­ous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.

Indicates an imminent hazardous situation which, if
not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful infor­mation about proper operation of the equipment.

NOTICE

Safety Instructions for Power Tools

OWNER’S MANUAL. Read and under-

stand this owner’s manual BEFORE using
machine.

TRAINED OPERATORS ONLY. Untrained
operators have a higher risk of being hurt
or killed. Only allow trained/supervised
people to use this power tool. When tool
is not being used, disconnect power, and
store in out-of-reach location to prevent
unauthorized use—especially around
children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not
use tools in areas that are wet, cluttered,
or have poor lighting. Operating tools in
these areas greatly increases risk of acci­dents and injury.

MENTAL ALERTNESS REQUIRED. Full
mental alertness is required for safe oper­ation of power tools. Never operate under
the influence of drugs or alcohol, when
tired, or when distracted.

DISCONNECT POWER FIRST. Always
disconnect tool from power supply
BEFORE making adjustments, chang­ing tooling, or servicing machine. This
prevents an injury risk from unintended
startup or contact with live electrical com­ponents.

EYE PROTECTION.

Always wear ANSI-

approved safety glasses or a face shield

when operating or observing machinery to

reduce the risk of eye injury or blindness
from flying particles. Everyday eyeglasses
are not approved safety glasses.

Model T28062 (Mfd. Since 08/17)-2-

ELECTRICAL SAFETY. Tool plug must
match outlet. Double-insulated tools have
a polarized plug (one blade is wider than
the other), which must be plugged into a
polarized outlet. Never modify plug. Do
not use adapter for grounded tools. Use
a ground fault circuit interrupter if opera­tion is unavoidable in damp locations.
Avoid touching grounded surfaces when
operating tool.

WEARING PROPER APPAREL. Do not
wear clothing, apparel or jewelry that
can become entangled in moving parts.
Always tie back or cover long hair. Wear
non-slip footwear to avoid accidental
slips, which could cause loss of workpiece
control. Wear hard hat as needed.

HAZARDOUS DUST. Dust created while
using tools may cause cancer, birth
defects, or long-term respiratory damage.
Be aware of dust hazards associated with
each workpiece material, always wear
a NIOSH-approved respirator, and con­nect tool to an appropriate dust collection
device to reduce your risk.

HEARING PROTECTION. Always wear
hearing protection when operating or
observing loud machinery. Extended
exposure to this noise without hearing
protection can cause permanent hearing
loss.

REMOVE ADJUSTING TOOLS. Never
leave adjustment tools, chuck keys,
wrenches, etc. in or on tool—especially
near moving parts. Verify removal before
starting!

INTENDED USAGE. Only use tool for its
intended purpose. Never modify or alter
tool for a purpose not intended by the
manufacturer or serious injury or death
may result!

AWKWARD POSITIONS. Keep proper
footing and balance at all times when
operating tool. Do not overreach! Avoid
awkward hand positions that make tool
control difficult or increase the risk of
accidental injury.

SAFE HANDLING. Firmly grip tool. To
avoid accidental firing, do not keep finger
on switch or trigger while carrying.

FORCING TOOLS.. Use right tool for job,
and do not force it. It will do job safer and
better at rate for which it was designed.

SECURING WORKPIECE. When
required, use clamps or vises to secure
workpiece. This protects hands and frees
both of them to operate tool.

GUARDS & COVERS.

Guards and cov-

ers reduce accidental contact with mov­ing parts or flying debris. Ensure they
are properly installed, undamaged, and
working correctly.

CHILDREN & BYSTANDERS. Keep chil­dren and bystanders at a safe distance
from the work area. Stop using tool if they
become a distraction.

USE RECOMMENDED ACCESSORIES.
Consult this manual or manufacturer
for recommended accessories. Using
improper accessories will increase risk of
serious injury.

MAINTAIN WITH CARE. Keep cutting
tool edges sharp and clean. Follow all
maintenance instructions and lubrication
schedules to keep tool

in good work-

ing condition. A tool that is improperly
maintained could malfunction, leading to
serious personal injury or death. Only
have tool serviced by qualified service­personnel using matching replacement
parts.

CHECK DAMAGED PARTS. Regularly
inspect tool for any condition that may
affect safe operation. Immediately repair
or replace damaged or mis-adjusted parts
before operating tool.

MAINTAIN POWER CORDS. When dis­connecting cord-connected tools from
power, grab and pull the plug—NOT the
cord. Carrying or pulling the cord may
damage wires inside. Do not handle cord/
plug with wet hands. Avoid cord damage
by keeping it away from heated surfaces,
high traffic areas, harsh chemicals, sharp
edges, moving parts, and wet/damp loca­tions. Damaged cords increase risk of
electrocution.

UNATTENDED OPERATION. Never
leave tool running while unattended. Turn
tool OFF and ensure all moving parts
completely stop before walking away.

EXPERIENCING DIFFICULTIES.

If at

any time you experience difficulties per­forming the intended operation, stop
using the machine! Contact our Technical
Support at [phone].

Model T28062 (Mfd. Since 08/17) -3-

No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage to
equipment or poor work results.

Additional Warnings for Rotary Tools

ELECTROCUTION HAZARDS. DO NOT

operate tool in wet or damp conditions.
Remove all liquids from the work area
before beginning operation. Make sure
your hands are clean and dry.

WORKPIECE CONTACT. Jamming spin­ning tool against the workpiece could
cause workpiece or tool to shatter and
send debris in all directions. Firmly grasp
rotary tool and ease it into workpiece.

TOOL CAPACITIES. To avoid damage to
tool or workpiece that may cause operator
injury, ALWAYS operate tool within capaci­ties stated on Page 4.

ACCIDENTAL STARTUP. To avoid unex­pected startup that may cause injuries,
ALWAYS make sure ON/OFF/Variable_
speed dial is turned OFF before connect­ing tool to power.

UNATTENDED TOOL. DO NOT leave
tool unattended when connected to power.
Always disconnect tool from power before
leaving work area.

CLAMP THE WORKPIECE. If spinning
tool slips from workpiece while you are
holding it, you could suffer piercing or
abrasion injuries. DO NOT hold workpiece
with one hand and operate tool with the
other. Secure workpiece in a vise or work­holding device before starting rotary tool.

EXPLOSION HAZARDS. Sparks from
grinding operation can easily ignite
flammable gasses, fluids, or materials.
ALWAYS make sure these substances
are completely removed from work area
before beginning operation.

ENTANGLEMENT HAZARDS. Loose
clothing or jewelry can become entangled
with spinning tool, pulling hands and fin­gers into bit. To avoid this risk, remove
jewelry, secure loose clothing, button long
sleeves, and tie back long hair.

SAFE HANDLING. DO NOT push spindle
lock during startup or operation. DO NOT
lay tool down until spindle comes to a
complete stop.

Serious injury or death can occur from fingers, clothing, jewelry, or hair getting
entangled in spindle or other moving components. Abrasion injuries can occur
from touching rotating bits, burrs, or cones with bare skin. Debris thrown by
rotary tools can strike operator or bystanders with moderate force, causing
impact injuries. Long-term respiratory damage can occur from using rotary tools
without proper use of a respirator. To reduce the risk of thee hazards, operator
and bystanders MUST completely heed the hazards and warnings below.