Page 1
MODEL T27951
SINGLE-DOOR,
4-DRAWER CABINET
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T27951 Single-Door, 4-Drawer Cabinet
requires some assembly. Follow the instructions
below for assembly, operation, and maintenance.
Figure 1. Model T27951.
• To reduce risk of crushing injuries from
tool cabinet tipping over on you:
— Do not stand on cabinet or in drawers.
— Only open one drawer at a time.
— Only move or transport cabinet with all
drawers and door closed and locked.
— Push cabinet only (do not pull it) when
moving.
• Do not exceed weight capacities:
— Max individual drawer weight limit is
175 lbs.
— Max individual shelf weight limit
is 275 lbs.
— Max total tool cabinet weight limit
(including contents) is 1250 lbs.
• To prevent accidental tipping, ensure
adjustable feet are down and cabinet
body is level.
• Do not allow children to have unsupervised
access to cabinet.
Inventory Qty
• Tool Cabinet with Drawers ........................... 1
• Cabinet Feet ................................................ 4
• Keys ............................................................. 2
Assembly
The Model T27951 comes with four adjustable
feet for leveling the cabinet.
To install feet:
1. With help from another person, lay cabinet
upside down on floor (see Figure 2).
2. Install one adjustable foot in each corner (see
Figure 2).
Adjustable Feet
Figure 2. Location of adjustable feet.
3. To prevent tipping or rocking, level the cabi-
net body by rotating the cabinet feet up or
down as needed.
Maintenance
• Use a soft, clean cloth and soapy water to
remove grease, dirt, or oil. Do not use solvents or flammable cleaning liquids.
• Lubricate lock annually with graphite.
COPYRIGHT © MARCH, 2017 BY GRIZZLY INDUSTRIAL, INC., REVISED JULY, 2017 (MN)
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 10.16) #JH18542 PRINTED IN CHINA
V1.0 7.17
Page 2
Adjusting Doors
Each 90° soft-close door hinge is riveted in place.
However, the doors may be adjusted inward or
outward, and left or right, as needed.
To adjust doors:
1. Close door and visually confirm gap spacing
around door edge is
(see Figure 3).
— If door spacing is equal, no adjustments
are needed.
— If door spacing is not equal, proceed to
Step 2.
1
⁄8" all the way around
Removing & Installing Drawers
The drawers can be removed and re-installed, if
necessary.
To remove a drawer:
1. Fully extend drawer and remove contents.
2. Push left locking tabs on drawer runner down
and hold, then pull right locking tabs on
drawer runner up and hold (see Figure 5).
3. Remove drawer from drawer slide.
Drawer
Runner
Locking Tab
1
⁄8" Gap
Figure 3. Checking door gap spacing.
2. Adjust door hinges using screws shown in
Figure 4.
1
Note: Only small adjustments, such as
1
⁄4 turn at a time, are required to move
or
⁄8
door position. Check spacing after each
adjustment.
Right/Left
Adjustment
Figure 5. Location of drawer locking tabs.
4. To re-install drawer, extend drawer slides out
all the way, insert drawer runners into slides,
and close drawer entirely. Locking tabs will
click in place as drawer is closed, which will
fully attach drawer to slides.
Installing Shelf Supports
Each shelf comes with four shelf supports, which
fit into the channel brackets inside the cabinet
(see Figure 6), making the height of each shelf
adjustable. (Shelf supports must be mounted
evenly to function properly.)
Shelf
Support
In/Out
Adjustment
Figure 4. Hinge adjustments.
-2-
Channel
Bracket
Figure 6. Shelf support and channel bracket.
T27951 Tool Cabinet (Mfd. 10/16)
Page 3
19
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
Grizzly Cabinet Series
The T27951 Single-Door, Four-Drawer Cabinet is part of our heavy-duty 10-piece storage set. These modular cabinets will enhance storage and workspace in the shop or garage, and they can be mixed and matched
to create a variety of storage solutions.
T27947 T27952 T27951T27948
T27953
T27949
15
8
12
20
21
11
T27950
Parts Breakdown & List
22
9
10
17
16
13
5
7
4
6
14
2
1
18
3
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT27951001 CABINET BODY 12 PT27951012 DOOR HANDLE
2 PT27951002 ADJUSTABLE FEET M12-1.75 X 30 13 PT27951013 DRAWER LINER
3 PT27951003 CABLE GROMMET 14 PT27951014 SHELF SUPPORT
4 PT27951004 HINGE, 90-DEG SOFT-CLOSE 15 PT27951015 FLAT HD SCR M4-.7 X 8
5 PT27951005 SHELF 16 PT27951016 DOOR LOCK W/2 KEYS
6 PT27951006 DRAWER SLIDE 17 PT27951017 DRAWER LOCK W/2 KEYS
7 PT27951007 DRAWER HANDLE 18 PT27951018 TOUCH-UP PAINT, GLOSSY BLACK
8 PT27951008 DOOR HANDLE CAP 19 PT27951019 TOUCH-UP PAINT, RED
9 PT27951009 DRAWER 7" 20 PT27951020 WARNING LABEL
10 PT27951010 DRAWER 9" 21 PT27951021 QR CODE LABEL
11 PT27951011 DOOR 22 PT27951022 GRIZZLY.COM LABEL, GOLD
T27951 Tool Cabinet (Mfd. 10/16)
-3-
Page 4
Loading...