Page 1
MODEL T27949
2-DOOR CLOSET
CABINET
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T27949 2-Door Closet Cabinet requires
some assembly. Follow the instructions below for
assembly, operation, and maintenance.
Figure 1. Model T27949.
Inventory Qty
• 2-Door Closet Cabinet with Shelves ............ 1
• Cabinet Feet ................................................ 4
• Keys ............................................................. 2
Assembly
The Model T27949 comes with four adjustable
feet for leveling the cabinet.
To install feet:
1. With help from another person, lay cabinet
upside down on floor (see Figure 2).
Note: We recommend sweeping the floor
clean and laying down a piece of cardboard
or a blanket to prevent scratching the finish
during this step.
2. Install one adjustable foot in each corner (see
Figure 2).
• To reduce risk of crushing injuries from
tool cabinet tipping over on you:
— Do not stand on cabinet.
— Only move or transport cabinet with all
doors closed and locked.
— Push cabinet only (do not pull it) when
moving.
• Do not exceed weight capacities:
— Max individual shelf weight limit
is 325 lbs.
— Max total tool cabinet weight limit
(including contents) is 1300 lbs.
• To prevent accidental tipping, ensure
adjustable feet are down and cabinet
body is level.
• Do not allow children to have unsupervised
access to cabinet.
COPYRIGHT © MARCH, 2017 BY GRIZZLY INDUSTRIAL, INC., REVISED JULY, 2017 (MN)
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 10.16) #JH18540 PRINTED IN CHINA
Adjustable Feet
Figure 2. Location of adjustable feet.
3. To prevent tipping or rocking, level the cabi-
net body by rotating the cabinet feet up or
down as needed.
V1.0 7.17
Page 2
Adjusting Doors
Each 90° soft-close door hinge is riveted in place.
However, the doors may be adjusted inward or
outward, and left or right, as needed.
To adjust doors:
1. Close door and visually confirm gap spacing
around door edge is
(see Figure 3).
— If door spacing is equal, no adjustments
are needed.
1
⁄8" all the way around
Mounting
To mount, locate wall studs at desired mounting location. Pre-drill (2)
wall cabinet to align with each stud, and secure
cabinet to the wall (see Figure 5). Due to the load
capacity of the cabinet, always mount directly to
wall studs!
1
⁄4" mounting holes into
Hardware Needed Qty
• Socket Wrench 3⁄8" ....................................... 1
• Flat Washers
• Lag Screw
1
⁄4" ......................................... 2
1
⁄4"-20 x 1" .................................. 2
— If door spacing is not equal, proceed to
Step 2.
1
⁄8" Gap
Figure 3. Checking door gap spacing.
2. Adjust door hinges using screws shown in
Figure 4.
1
Note: Only small adjustments, such as
1
⁄4 turn at a time, are required to move
or
⁄8
door position. Check spacing after each
adjustment.
Cabinet Body
Lag Screw
Wall
Stud
(1 of 2)
Flat Washer
Figure 5. Mounting cabinet to wall.
Installing Shelf Supports
Each shelf comes with four shelf supports, which
fit into the channel brackets inside the cabinet
(see Figure 6), making the height of each shelf
adjustable. (Shelf supports must be mounted
evenly to function properly.)
Shelf
Support
In/Out
Adjustment
Figure 4. Hinge adjustments.
-2-
Right/Left
Adjustment
Channel
Bracket
Figure 6. Shelf support and channel bracket.
Maintenance
• Use a soft, clean cloth and soapy water (use
regular dish soap) to remove grease, dirt, or
oil. Do not use solvents or flammable cleaning liquids.
• Use graphite to lubricate lock annually.
T27949 Tool Cabinet (Mfd. 10/16)
Page 3
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
Grizzly Cabinet Series
The T27949 2-Door Closet Cabinet is part of our heavy-duty 10-piece storage set. These modular cabinets
will enhance storage and workspace in the shop or garage, and they can be mixed and matched to create
a variety of storage solutions.
T27949
11
16
T27948
T27947
T27952
T27951
T27953
Parts Breakdown & List
15
14
6
12
17
5
T27950
9
4
10
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT27949001 CABINET BODY 10 PT27949010 DOOR HANDLE CAP
2 PT27949002 ADJUSTABLE FEET M12-1.75 X 30 11 PT27949011 FLAT HD SCR M4-.7 X 8
3 PT27949003 CABLE GROMMET 12 PT27949012 LOCK W/2 KEYS
4 PT27949004 SHELF SUPPORT 13 PT27949013 TOUCH-UP PAINT, GLOSSY BLACK
5 PT27949005 SHELF 14 PT27949014 TOUCH-UP PAINT, RED
6 PT27949006 HINGE, 90-DEG SOFT-CLOSE 15 PT27949015 WARNING LABEL
7 PT27949007 DOOR (RIGHT) 16 PT27949016 QR CODE LABEL
8 PT27949008 DOOR (LEFT) 17 PT27949017 GRIZZLY.COM LABEL, GOLD
9 PT27949009 DOOR HANDLE
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
8
7
3
2
1
13
T27949 Tool Cabinet (Mfd. 10/16)
-3-
Page 4
Loading...