Grizzly T26868 User guide

MODEL T26868

MANUAL ROTARY SHEAR

INSTRUCTIONS

For questions or help with this product contact Tech Support at [phone] or [e-mail]

Introduction

The Model T26868 Manual Rotary Shear is capa­ble of cutting smooth curves into sheet metal up
to 2mm thick, with a "throatless" frame design that
allows for unlimited material width. The ratcheting
handle and two circular blades provide excellent
feeding control and manipulation of the workpiece.

Specifications

Max. Material Thickness ......................14 Gauge

Min. Shearing Radius ................................... 1 in.

Shearing Width .......................................No Limit

Basic Operation

1. Mark cut line on workpiece.

2. Place workpiece on infeed side of shear body
(see Figure 1) and align cut line with blades.

AMPUTATION HAZARD !
Do not place hands or fingers
in blade path while feeding.
Doing so could result in
lacerations or amputation!

Mount shear securely to workbench. Failure
to do so could cause tool to fall during use
and result in serious crushing injury.

Mounting and Assembly

1. Place shear on workbench, and use holes in

base to mark drilling location on workbench.

2. Drill mounting holes and attach shear to
workbench with (4) 10mm or
hex nuts, and flat washers (not included).

Note: For strongest mounting, we recom-

mend using hex bolts to mount shear to work­bench. Otherwise, fasten directly to work­bench with lag bolts and flat washers.

3. Mount ratchet handle to upper blade shaft so
ratchet turns blade when pressing down on
handle toward front of tool.

3

⁄8" hex bolts,

— If necessary have a helper support free

end of workpiece.

Outfeed

Figure 1. Model T26868.

3. Push ratcheting handle down toward front of

tool to turn blades, initiating cut.

4. Return handle to starting position and repeat
Step 3 until shearing operation is complete.

Infeed

COPYRIGHT © OCTOBER, 2014 BY GRIZZLY INDUSTRIAL, INC.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#WK16813 PRINTED IN CHINA

V1.10.14

Blade Adjustment

The gap between the upper and lower blade may
need to be adjusted depending on the material
you are shearing. In general, the thicker the mate­rial, the greater the blade gap should be.

3. Using a 13mm open-end wrench, rotate
depth stop bolt (see Figure 3) until blades
overlap approximately

4. Tighten hex nut shown in Figure 3 to lock
depth stop bolt.

1

⁄8".

If the blade gap is too large, burrs can form on
the sheared edges. A gap which is too small can
cause difficulty in the shearing operation.

Some amount of experimentation may be neces­sary to achieve the desired results.

To adjust blade gap:

1. Using a 19mm open-end wrench, loosen both

M12-1.75 hex nuts shown in Figure 2.

Hex

Nuts

5. Tighten hex nuts loosened during Step 1.

6. Test shearing operation on a piece of scrap

material that is same thickness as workpiece.
If necessary, repeat Steps 1–6.

Using Miter Gauge

When shearing straight lines, we recommend
using the included miter gauge as a guide.

To install miter gauge:

1. Insert guide shaft into shear body and secure

set screw shown in Figure 4.

Miter

Gauge

Knob

Guide

Shaft

Figure 2. Location of blade adjustment hex nuts.

2. Using a 22mm open-end wrench, rotate

blade adjustment shaft (Figure 3) to set
desired blade gap.

Depth Stop

Bolt

Hex Nut

Figure 3. Location of blade adjustment shaft and

depth stop.

Blade

Adjustment

Shaft

Set

Screw

Figure 4. Miter gauge installed.

2. Loosen miter gauge knob (see Figure 4),

adjust miter gauge to desired angle, then
tighten knob.

3. Proceed with shearing operation, as described
in Steps 1–4 of Basic Operation on Page 1,
using miter gauge as a fence to guide work­piece.

-2-

T26868 Manual Shear (Mfg. 8/14+)

T26868 Parts Breakdown

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.

39

1

29

5

14

30

31

38

18

17

4

19

20

21

22

33

34

2

3

8

9

11

12

10

7

13

16

6

14

15

16

15

23

35

24

36

28

18

27

26

15

16

37

25

15

16

10

32

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT26868001 MITER GAUGE 21 PT26868021 FLAT WASHER 6MM
2 PT26868002 MITER GAUGE KNOB 22 PT26868022 PHLP HD SCR M6-1 X 16
3 PT26868003 RATCHETING HANDLE 1/2" 23 PT26868023 TROUGH PLATE
4 PT26868004 RATCHETING HANDLE EXTENSION 24 PT26868024 HEX NUT M12-1.75
5 PT26868005 GUIDE BLOCK 25 PT26868025 SHEAR BODY
6 PT26868006 GUIDE SHAFT 26 PT26868026 SET SCREW M8-1.25 X 30
7 PT26868007 ANGLE INDICATOR 27 PT26868027 HEX BOLT M8-1.25 X 40
8 PT26868008 PHLP HD SCR M4-.7 X 8 28 PT26868028 THREADED SHAFT M8-1.25
9 PT26868009 FLAT WASHER 4MM 29 PT26868029 LOWER BLADE
10 PT26868010 SET SCREW M6-1 X 8 30 PT26868030 SHAFT HOUSING
11 PT26868011 UPPER SHAFT 31 PT26868031 BLADE ADJUSTMENT SHAFT
12 PT26868012 KEY 5 X 5 X 10 32 PT26868032 LOWER BLADE SHAFT
13 PT26868013 UPPER BLADE 33 PT26868033 AMPUTATION HAZARD WARNING LABEL
14 PT26868014 HEX NUT M12-1.75 34 PT26868034 EYE INJURY HAZARD WARNING LABEL
15 PT26868015 LOCK WASHER 12MM 35 PT26868035 MACHINE WARNING LABEL
16 PT26868016 FLAT WASHER 12MM 36 PT26868036 MACHINE ID LABEL
17 PT26868017 HEX BOLT M8-1.25 X 10 37 PT26868037 GRIZZLY GREEN TOUCH-UP PAINT
18 PT26868018 HEX NUT M8-1.25 38 PT26868038 HEX BOLT M10-1.5 X 35
19 PT26868019 HANDLE SHAFT 39 PT26868039 HEX NUT M10-1.5
20 PT26868020 HANDLE

T26868 Manual Shear (Mfg. 8/14+)

-3-

MODEL T26868 MANUAL SHEAR

Product Dimensions:

Weight ............................................................................................................................................................................. 47 lbs.

Width (side-to-side) x Depth (front-to-back) x Height ......................................................................................17 x 9 x 12

Foot Print (Length/Width) ............................................................................................................................................ 7

Shipping Dimensions:

Type ................................................................................................................................................................... Cardboard Box

Weight .............................................................................................................................................................................. 49 lbs.

Length/Width/Height ........................................................................................................................................... 13 x 10 x 14 in.

Must Ship Upright .................................................................................................................................................................. No

Main Specifications:

Upper Blade Diameter ......................................................................................................................................................65mm

Lower Blade Diameter ......................................................................................................................................................65mm

Maximum Length of Single Cut ....................................................................................................................................Unlimited

Mounting Bolt Hole Diameter ..............................................................................................................................................

Capacities:

Maximum Material Thickness ........................................................................................................... 14 Gauge, 0.08 in. (2mm)

Maximum Material Width .............................................................................................................................................Unlimited

Miter Gauge Angle .................................................................................................................................Left 60 – Right 60 deg.

Construction:

Shear Blades ............................................................................................................................................................T10A Steel

Frame ........................................................................................................................................................................... Cast Iron

1

⁄2 in.

1

⁄2 x 8 in.

1

⁄2 in.

Other Specifications:

Country of Origin ............................................................................................................................................................... China

Warranty ........................................................................................................................................................................... 1 Year

Serial Number Location ..................................................................................................................................ID Label on Base

Assembly Time ........................................................................................................................................................... 5 Minutes

Features:

Dual rotary blades for cutting curves and complex shapes
"Throatless" frame allows for unlimited workpiece width
Miter gauge for cutting straight lines at various angles
Ratcheting handle provides excellent control of workpiece
Heavy-duty cast iron frame mounts to workbench

-4-

T26868 Manual Shear (Mfg. 8/14+)