Page 1
2 HP 230V 3-PHASE
MAGNETIC SWITCH
Electrocution or
fire could occur if
this switch is not
installed or adjusted by a qualified
electrician!
MODEL T24103
INSTRUCTIONS
230 Volt
3-Phase
Power Source
1L1
3L2 5L3
13
NO
Figure 1. Model T24103 magnetic
switch.
Contactor TECO
CU-16 (230V Coil)
COLOR KEY
BLACK
GREEN
RED
YELLOW
Bk
Gn
Rd
Thermal Overload Relay
TECO RHU-10K1
(7. 2–10A)
TECO
CU16
2T1
4T2
6T3
97 NO
2T1
9
10 A
8
98 NO
4T2
O
7.2
OFF
95 NC
TRIP IND.
TEST
2 HP 230V Motor
14
6T3
NO
R
RESET
96 NC
NO
53
Ground
ON
54
NO
M
A
OPE R ATION : When pushed, the green ON button on the outside cover of the magnetic switch energizes
a magnetic coil, which pulls the contactor closed. The main current then passes through the contactor
and thermal overload relay to the motor. The red OFF button breaks the magnetic field, which opens the
contactor and disconnects the current to the motor. A motor overload or an interruption of the power supply
will also break the magnetic field and release the contactor and disconnect current to the motor. The motor
will not re-start until the overload is reset and/or the ON button is pushed.
COPYRIGHT © OCTOBER, 2011 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#ST14416 PRINTED IN TA IWAN
Page 2
Thermal Relay Overload Amp
REF DESCRIPTION REF DESCRIPTION
Adjustment Dial: Turn this dial
to the amperage setting specified by the motor manufacturer.
Typically, this setting is 100–
110% of the amperage load listed
on the motor data plate. Please
note that turning this dial has
no effect on increasing motor
horsepower. If turned too high,
the motor can overheat and be
damaged before the relay trips.
Trip Indicator: If this window
turns yellow, the thermal relay
has tripped.
Manual Contactor Override
Lug: When pushed, the contactor
is manually closed for troubleshooting purposes only.
ON Button: When pushed,
power is sent to the magnetic
field coil, closing the contactor
and sending power to the motor.
Manual/Auto Reset Lever: In
the up position, the thermal relay
is in manual reset mode. This
means you must re-install the
outside cover and push the red
OFF button, then push the green
ON button to reset the thermal
relay. In the down position, the
thermal relay will automatically
reset when it has cooled.
Manual Trip Test Lever: If the
thermal relay function is in question, run the motor and use a
wooden toothpick to slide the
yellow test lever to the left. If the
motor shuts off, the thermal relay
has tripped and is functional.
10
11
1
Reset Button: When pushed,
the thermal relay is reset, clearing the yellow trip indicator window.
OFF Button: When pushed, the current going to the magnetic field
coil is cut, which opens the contactor and cuts power to the motor.
Parts Breakdown
3
4
8
6
7
9
5
2
12
1 SWITCH BOX 7 PHLP HD SCR M3-.5 X 10
2 SWITCH BOX COVER ASSEMBLY 8 CAPTURED GROUND SCR M4-.7 X 10
3 CONTACTOR TECO CU-16 230V 9 PHLP HD SCR 10-24 X 1-1/2
4 FIELD SWITCH TECO CNA-1 10 LIQUID-TITE STRAIN RELIEF
5 OL RELAY TECO RHU-10K1 7.2-10A 11 RUBBER SEAL
6 GROUNDING PLATE 12 PLASTC SCREW M10-1.5 X 20 GRAY
-2-
T24103 Magnetic Switch
Loading...