Grizzly T1238 User Manual

MODEL T1238

MOBILE TOOL TABLE

INSTRUCTIONS

For Models Mfd. Since 10/17

For questions or help with this product contact Tech Support at [phone] or [e-mail]

Introduction

The Model T1238 Mobile Tool Table is designed
to provide a stable, mobile platform for mounting
machinery and equipment.

Figure 1. Model T1238 Mobile Tool Table.

Specifications

• Footprint (Length x Width) ..............20" x 23"

• Height ......................................................30"

• Maximum Weight Capacity ............. 300 lbs.

• Approximate Assembly Time .......30 Minutes

Needed for Assembly

• Open-End Wrenches or Sockets 13mm ..... 2

• Hex Wrench 5mm ....................................... 1

H. Linkage Bar/Pedal ...................................... 1

I. Caster ......................................................... 1

J. Upper Braces (Front & Back) ..................... 2

K. Pedal Assembly .......................................... 1

L. Wheel Assembly ......................................... 1

M. Handle ........................................................ 1

N. Hardware Bag (Not Shown)

—Carriage Bolts M8-1.25 x 12 ................. 30

—Button Hd Cap Screws M8-1.25 x 16 ... 12

—Flat Head Screws M8-1.25 x 25 ............. 4

—Hex Bolts M8-1.25 x 20 .......................... 2

—Hex Bolt M8-1.25 x 70 ............................ 1

—Flange Nuts M8-1.25 ............................ 38

—Lock Nuts M8-1.25 .................................. 3

—Extension Spring .................................... 1

A

D

B

C

E

H

F

I

G

Inventory

Description Qty

A. Table Top ................................................... 1

B. Shelf ........................................................... 1

C. Side Panels ................................................ 2

D. Legs w/Foot Pads ....................................... 4

E. Tool Holder ................................................. 1

F. Upper Braces (Left & Right) ....................... 2

G. Lower Braces ............................................. 2

COPYRIGHT © FEBRUARY, 2018 BY GRIZZLY INDUSTRIAL, INC. REVISED JULY, 2018 (TK)

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TKAB19421 PRINTED IN CHINA

K

J

L

Figure 2. Inventory.

M

V1.07.18

Assembly

This tool table must be fully assembled before it
can be used. Before beginning the assembly pro­cess, refer to Needed for Assembly and gather
all listed items.

To assemble tool table:

3. Repeat Step 1 in a similar manner to build

side assembly B.

4. Attach pedal assembly to side assembly B
built in Step 3 with (4) M8-1.25 x 16 button
head cap screws. Ensure pedal points out­ward (see Figure 5).

1. Build side assembly A by attach­ing (1) front upper brace to (2) legs with
(4) M8-1.25 x 12 carriage bolts and
(4) M8-1.25 flange nuts (see Figure 3). Use
90° square to make sure legs and supports
are perpendicular (see Figure 3).

Upper

x 4

Legs

Figure 3. Side assembly A built.

2. Attach wheel assembly to side assembly

A with (4) M8-1.25 x 16 button head cap
screws. Long linkage should point outward
(see Figure 4) with wheels in the down
position.

Brace

90
Degree
Square

Pedal

Pointing

Outward

Figure 5. Pedal assembly orientation.

5. Attach caster to pedal assembly with (1)

M8-1.25 x 70 hex bolt and (1) M8-1.25 lock
nut (see Figure 6).

Pedal

Assembly

x 4

x 4

Linkage
Pointing

Outward

Figure 4. Wheel assembly orientation.

-2-

Wheel

Down

Caster

x 1

Figure 6. Caster wheel attached to pedal

assembly.

T1238 Tool Table (Mfd. Since 10/17)

6. Attach (2) upper braces and shelf to side
assembly A with (6) M8-1.25 x 12 car­riage bolts and (6) M8-1.25 flange nuts
(see Figure 7).

7. Attach (2) lower braces to side assembly A
with (2) M8-1.25 x 16 button head cap screws
and (2) M8-1.25 flange nuts (see Figure 7).

10. Turn table assembly upside down.

11. Loosely attach linkage bar to wheel assem-

bly with (1) M8-1.25 x 20 hex bolt and
(1) M8-1.25 lock nut to allow movement.
Connect extension spring to linkage bar and
wheel assembly (see Figure 9).

Upper
Brace

x 6

Side Assembly A

Figure 7. Upper/Lower braces and shelf

attached to side assembly A.

8. Attach side assembly A to side assembly
B with (6) M8-1.25 x 12 carriage bolts and
(6) M8-1.25 flange nuts (see Figure 8).

9. Attach side assembly B to lower braces with
(2) M8-1.25 x 16 button head cap screws and
(2) M8-1.25 flange nuts, as shown in Figure

8.

Lower
Brace

Shelf

x 2

Linkage Bar

Figure 9. Linkage and spring installed.

12. Loosely attach linkage bar to pedal assem-

bly with (1) M8-1.25 x 20 hex bolt and (1)
M8-1.25 lock nut to allow movement (see
Figure 10).

x 1

Extension Spring

Wheel Assembly

Linkage

Bar

Side Assembly B

x 6

x 6

x 2
x 2

Side Assembly A

Figure 8. Side assembly B attached.

T1238 Tool Table (Mfd. Since 10/17)

x 1

Figure 10. Linkage bar attached to pedal

assembly.

-3-

13. Turn table assembly unit upright. Attach bot­tom of a side panel to table assembly shelf
with (2) M8-1.25 x 12 carriage bolts and
(2) M8-1.25 flange nuts (see Figure 11).

16. Attach tool holder and top of side panel
with (2) M8-1.25 x 12 carriage bolts and
(2) M8-1.25 flange nuts (see Figure 13).

Note: Position side panel so end with
long tab faces up.

Long Tab

Side

Panel

Shelf

Short Tab

x 2

Figure 11. Bottom of side panel attached.

14. Attach handle and top of side panel

with (4) M8-1.25 x 12 carriage bolts and
(4) M8-1.25 flange nuts (see Figure 12).

Tool

Holder

x 2

Figure 13. Tool holder attached.

17. Attach table top with (4) M8-1.25 x 25 flat

head screws and (4) M8-1.25 flange nuts
(see Figure 14).

Note: The handle goes on the same side
as the pedal assembly.

Handle

Side

x 4

Figure 12. Top of side panel and handle

attached.

15. Repeat Step 13 to attach second side panel
to opposite side of table assembly (see
Figure 11).

Panel

x 4

Figure 14. Table top attached.

18. Ensure all fasteners are firmly tightened and

wheel mechanism operates smoothly.

-4-

T1238 Tool Table (Mfd. Since 10/17)

The Model T1238 Mobile Tool Table is designed

of gravity (like table-top drill presses or
mortising machines) on this table. Doing
so could cause the table to tip and fall,

Failure to properly mount machines to

to have machines mounted to it. Mount the
machines to the table top with applicable hard­ware (not included).

The strongest mounting option is a "Through
Mount" (see Figure 15) where holes are drilled
all the way through the table, and hex bolts,
washers, and hex nuts are used to secure the
machine in place.

Hex
Bolt

Flat Washer

Machine Base

Table Top

Moving Tool TableMounting Machines to Table

Depress the lifting pedal to raise the table onto
the wheels. Carefully steer the table to the desired
location, then depress the smaller linkage pedal
to lower the unit onto its feet (see Figure 16).

Linkage

Pedal

Figure 16. Moving controls.

Lifting
Pedal

Flat Washer

Lock Washer

Hex Nut

Figure 15. Through mount example.

table can cause tipping resulting in injury
property damage.

DO NOT mount machines with high centers

resulting in serious injury or death.

Any abrupt movement could cause the unit
to tip, resulting in serious personal injury
and property damage.

T1238 Tool Table (Mfd. Since 10/17)

-5-

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.

Parts Breakdown & List

1

8

2

20

27

21

4

3

3

17

4

18

5

9

6

3

7

13

3

16

3

10

4

4

14

4

6

32

22

23

24

12

25

32

19

3

6

28

29

31

3

30

BUY PARTS ONLINE AT GRIZZLY.COM !

Scan QR code to visit our Parts Store.

26

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT1238001 FLAT HD SCR M8-1.25 X 30 18 PT1238018 HANDLE
2 PT1238002 TABLE TOP 19 PT1238019 EXT RETAINING RING 20MM
3 PT1238003 FLANGE NUT M8-1.25 20 PT1238020 FLAT WASHER 20MM
4 PT1238004 CARRIAGE BOLT M8-1.25 X 16 21 PT1238021 LOCK WASHER 20MM
5 PT1238005 STAND LEG 22 PT1238022 SUPPORT FRAME
6 PT1238006 BUTTON HD CAP SCR M8-1.25 X 16 23 PT1238023 REAR ROLLER LEVER
7 PT1238007 FOOT PAD 24 PT1238024 EXTENSION SPRING
8 PT1238008 UPPER BRACE (FRONT & BACK) 25 PT1238025 LINKAGE BAR/PEDAL
9 PT1238009 LOWER BRACE 26 PT1238026 HEX BOLT M8-1.25 X 55
10 PT1238010 TOOL HOLDER 27 PT1238027 RUBBER WHEEL
12 PT1238012 HEX BOLT M8-1.25 X 20 28 PT1238028 CASTER
13 PT1238013 UPPER BRACE (LEFT & RIGHT) 29 PT1238029 HEX BOLT M8-1.25 X 70
14 PT1238014 SIDE PANEL 30 PT1238030 PEDAL ASSEMBLY
16 PT1238016 SHELF 31 PT1238031 EXT RETAINING RING 20MM
17 PT1238017 HANDLE CAP 32 PT1238032 LOCK NUT M8-1.25

-6-

T1238 Tool Table (Mfd. Since 10/17)

Labels & Cosmetics

41

45

44

40

42

43

300 lb. max weight
capacity. DO NOT
exceed. Stand may tip
or collapse, and
crushing injury may
occur.

REF PART # DESCRIPTION REF PART # DESCRIPTION

40 PT1238040 NOTICE LABEL 43 PT1238043 CAUTION LABEL
41 PT1238041 GRIZZLY INDUSTRIAL LABEL 44 PT1238044 GRIZZLY.COM LABEL
42 PT1238042 QR CODE LABEL 45 PT1238045 TOUCH-UP PAINT, GLOSSY BLACK

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact [phone] or www.grizzly.com.

T1238 Tool Table (Mfd. Since 10/17)

-7-

-8-

T1238 Tool Table (Mfd. Since 10/17)