Page 1
MODEL T1194
1/4"
Blade
Resaw Fence
Drift
Bar
RESAW FENCE
w/DRIFT BAR
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T1194 Resaw Fence with Drift Bar is
designed to help reduce blade lead (cut drift) by
creating a pivot point that provides more control
during resaw operations. The Model T1194 fits the
following Grizzly bandsaws:
• G0457
• G0 513X
• G0 513X2
• G0 513X2F
• G0 513X2B
• G0 513X2BF
• G0514X
• G0514X 2
• G0514X 2 B
• G0514X3
• G0514XF
• G0 531B
• G0555X
• G0566B
• G0569
• G0636X
• G0636XB
• G0640X
• G0701
• G0778
• G0817
Assembly
1. Insert adjustable handle with fender
washer through back of resaw fence (refer to
Parts Breakdown drawing).
2. Secure drift bar using adjustable
handle. Make sure drift bar is flat against
resaw fence and straight up and down.
Installation
1. DISCONNECT MACHINE FROM POWER!
2. Install a blade suitable for resaw operations.
We suggest using the widest possible blade
for your machine with 2–4 TPI (hook or skip
teeth) that is sharp and clean.
3. Slide resaw fence over moving plate on fence
assembly and tighten lock handle.
4. Move resaw fence up to blade so center of
drift bar is set approximately
blade teeth (see Figure 2).
1
⁄4" forward of
Figure 1. Model T1194 Resaw Fence w/Drift Bar.
Specifications
Fence Dimensions .......... 231⁄4"L x 13⁄8"W x 57⁄8"H
Drift Bar Dimensions .......................6
Weight ....................................................4.25 lbs.
Inventory
Resaw Fence..................................................... 1
Drift Bar w/Fender Washer & Adj. Handle......... 1
1
⁄4"L x 11⁄4"D
Drift Bar
Figure 2. Resaw fence with drift bar installed.
COPYRIGHT © OCTOBER, 2017 BY GRIZZLY INDUSTRIAL, INC. REVISED DECEMBER, 2017 (ES)
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#ES19241 PRINTED IN TAIWAN
Blade
V1.01.18
Page 2
Operation
1/4"
Blade
Resaw Fence
Drift
Bar
1. Mark reference cut line along top of workpiece (see Figure 3).
7. Slowly feed workpiece completely through
blade. Use drift bar as a pivot point to control
cut, as shown in Figure 4.
2. Lower bandsaw blade guides as close to
workpiece as possible (see Figure 3).
3. Adjust resaw fence so blade aligns with mark
made in Step 1 and center of drift bar is set
1
⁄4" forward of blade teeth (see Figure 3).
Blade
Guides
Blade
Cut Line
Drift
Mark
Bar
Workpiece
Note: The drift bar allows you to steer your
workpiece while cutting to quickly correct
blade lead and keep blade aligned with cut
line.
Blade
Blade
Drift
Bar
Guides
Cut Line
Mark
Workpiece
Figure 4. Resawing with drift bar.
Parts Breakdown & List
3
Figure 3. Workpiece positioned to cut using
resaw fence with drift bar.
4. Lock rip fence and resaw fence in position.
5. If necessary for cutting operation, support
ends of board with saw stand or roller stand.
6. Turn bandsaw ON.
2
1
4
5
REF PART # DESCRIPTION
1 PT1194001 ADJ HANDLE 65L, M8-1.25 X 25
2 PT1194002 FENDER WASHER 8MM
3 PT1194003 RESAW DRIFT BAR 6-1/4" X 1-1/4"
4 PT1194004 ALUMINUM RESAW FENCE 590MM
5 PT1194005 FENCE END CAP
6 PT1194006 TAP SCREW M3.5 X 12
6
T1194 Resaw Fence with Drift Bar (Mfd. 9/17)
BUY PARTS ONLINE AT GRIZZLY.C OM!
Scan QR code to visit our Parts Store.
-2-
Loading...