MODEL T10699
DOWNDRAFT SANDING
TABLE KIT
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
This kit allows you to create your own custom
Downdraft Sanding Table. You just need to construct the box, add a dust port, and connect it to
your dust collector or shop vacuum. Multiple kits
can also be combined to build larger tables.
Kit includes (4) downdraft panels, (64) rubber
downdraft grommets, (4) plastic work stops with
nuts, and (1) 4" dust port. Each panel measures
3
⁄4" W x 16 1⁄2 " L and is 13⁄16" high.
6
Kit Inventory
Example of Finished Kit
D
E
A
x 64
C
E
Cut List
ID Part T W L Qty
A Bottom Piece
B Front Piece
C Rear Piece
D Side Piece
E Insert
F Guide Bar
BC
1
⁄2 " 16 5⁄8 " 26 3⁄4" 1
1
⁄2 " 6 3⁄4" 26 3⁄4" 1
1
⁄2 " 6
1
⁄2 " 6 3⁄4" 17 3⁄4" 2
1
⁄2 " 9 1⁄2 " 16 5⁄8 " 2
1
⁄2 "
3
⁄4" 26
3
⁄8 " 26 3⁄4" 2
3
A
⁄4" 1
Model T10699 Downdraft Sanding Table Kit
Building Material & Fasteners
These instructions are designed for construction
1
⁄2 " sheet stock. If desired, you can substitute
with
the sheet stock with the wood type of your choice.
If using a different material thickness than specified, adjust the length of Side Pieces (D).
You also need to determine how you will fasten
the various kit components together, depending
on the desired quality. Common options are wood
screws, glue, brad nails/staples, biscuits, rabbets,
dovetails, or any combination of these together.
COPYRIGHT © FEBRUARY, 2013 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
FOR KITS MANUFACTURED SINCE 2/13 #TR15633 PRINTED IN TAIWA N
E
E
1
⁄2" x 30 1⁄2" x 48" sheet stock
DD
F
Dust Port Options
A 4" dust port has been included to connect your
downdraft table to a dust collector. If you want to
connect it to a shop vacuum, you can purchase
1
⁄2 " dust port or a 2 1⁄2" x 4" hose adapter from
a 2
Grizzly.
W1042 2 1⁄2" Angled Dust Port
W1044 2 1⁄2" x 4"
Hose Adapter
Construction
1. Cut out all pieces from the provided cut list.
2. Install rubber grommets in all panels, spacing
them out evenly and staggered in each row.
D4259 2 1⁄2" Straight Dust Port
Other Related Items from Grizzly
D4203—Clear Flexible Hose 2 1⁄2" x 10'
D4206—Clear Flexible Hose 4" x 10'
D2104—Hose Hanger for 2
D2107—Hose Hanger for 4" Hose
W1314—Wire Hose Clamp 2
W1317—Wire Hose Clamp 4"
W1007—Plastic Blast Gate 4" OD
D2251—Adjustable Circle Cutter 1"–5" Dia.
W1039—Universal Adapter 1"–6"
T25448—Dust Collector Remote Switch 110V
D4206
W1317
D2107
1
⁄2" Hose
1
⁄2"
W1039
D2251
3. Cut out the dust port hole in Rear Piece (C),
matching the hole diameter of the dust port.
Center the hole horizontally, and position
the bottom of the hole even with the top of
Bottom Piece (A), so dust will flow smoothly
into the dust port during operation.
Height of
Bottom
Piece (A)
C
C
C
A
Hole is
Horizontally
Centered
4. Mark a line for the mounting position of Guide
Bars (F) on Front Piece (B) and Rear Piece
(C). The mounting height of Guide Bars (F)
should allow panels to sit flush with the top
edge of Front Piece (B) and Rear Piece (C).
-2-
W1007
T25448
Marked Line
for Guide Bar
Mounting Position
Panel
Flush
Model T10699 (Mfg. Since 2/13)
C
F
B
5. Attach Guide Bars (F) to Front Piece (B) and
Rear Piece (C) with top edges along the lines
you marked in the previous step.
8. Attach Side Pieces (D) to Bottom Piece (A)
and Rear Piece (C).
C
B
6. Position one Side Piece (D) between Front
Piece (B) and Rear Piece (C), then place
a straightedge against the bottom of Guide
Bars (F) and mark a line across Side Piece
(D). Repeat with the other Side Piece (D).
These lines will help you position Inserts (E)
during a later step.
Line Indicating
B
Bottom Edge
of Guide Bars
D
C
A
D
9. Miter cut one end of Inserts (E) at 60° and the
other end at 30°.
60° 30°
E
10. Place the 60° ends of Inserts (E) just below
the lines on Side Pieces (D), then attach
Inserts (E) to Side Pieces (D) and Bottom
Piece (A).
D
C
7. Attach Rear Piece (C) to Bottom Piece (A).
C
A
60°
30°
D
E
A
C
E
D
Model T10699 (Mfg. Since 2/13)
-3-
11. Attach Front Piece (B) to Bottom Piece (A)
ry or lung damage from
dust, always wear safety
and Side Pieces (D).
Operation
The downdraft sanding table helps reduce airborne dust while sanding with a handheld electric
sander.
D
E
A
B
C
A
E
D
12. Place the panels on Guide Bars (F).
D
E
A
C
The dust port is connected to a shop vacuum or
dust collector, and a workpiece is placed on top
the downdraft table and sanded with an electric
handheld sander. As dust comes off the sander,
it is sucked through the downdraft table holes
and into the vacuum or dust collector—instead of
becoming airborne in the shop.
To reduce risk of eye inju-
goggles and a respirator
when operating machine!
Work Stops
The downdraft table kit includes four work stops.
The work stops can be placed inside the panel
holes to act as a barrier, preventing unwanted
workpiece movement when sanding.
13. Attach dust port over hole in Rear Piece (C).
D
E
A
C
E
Work Stops
D
E
A
C
Replacement Parts
Replacement rubber grommets and work stops
can be purchased if they get lost or damaged.
PT10699001
-4-
PT10699002
Model T10699 (Mfg. Since 2/13)
Loading...