Grizzly T10065, T10066 User guide

MODEL T10065/T10066
HIGH-PRECISION DOUBLE-
CLAMP MILLING VISE
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The 4" Model T10065 and 6" Model T10066 High-Precision Double-Clamp Milling Vise feature mobile jaws on each end and a removable fixed jaw in the center. This provides a wide variety of secure clamping options when working with com­plex workpieces, all while delivering over three tons of clamping pressure.
The vise can securely clamp onto a single work­piece using one set of mobile jaws, or clamp multiple workpieces of the same or different sizes. The vise can also be converted to a traditional vise by removing the fixed center jaw and fixing the step-side jaw to the body using the provided step-side lock plate.
Additionally, the vise can be fitted with different jaws and jaw plates, providing the most precise and secure holds possible for the workpiece. (Additional plates and jaws sold separately.)
Figure 1. Model T10065 High-Precision Double-
Clamp Milling Vise.
Maintenance
Keep all unpainted machined surfaces rust-free with regular applications of products like G96 Gun Treatment, SLIPIT
®
, or Boeshield® T-9.
Specifications
T10065:
Length Width Height Jaw Opening Jaw Opening (With Center Removed) Jaw Width Bed Height Maximum Pressure Limit Pressure Lockwell® Anti-Lift System Down-Thrust Mechanism Ratio Flame-Hardened Vise Bed Vise Body Vise Tensile Strength Meets or Exceeds JIS Grade 1 Standards Chip Covers Included Weight
T10066:
Length Width Height Jaw Opening Jaw Opening (With Center Removed) Jaw Width Bed Height Maximum Pressure Limit Pressure Lockwell® Anti-Lift System Down-Thrust Mechanism Ratio Flame-Hardened Vise Bed Vise Body Vise Tensile Strength Meets or Exceeds JIS Grade 1 Standards
®
Chip Covers Included Weight
............................................................. 18"
................................................................ 4"
......................................................... 3 13⁄16"
.................................................3 1⁄2 "
...........9 1⁄4"
......................................................... 4"
.....................................................2 1⁄2 "
..............................4,945 lbs.
.......................................5,845 lbs.
............................ Yes
.......................1:1
....................HRC 45°
............................. Ductile Iron FCD60
........................ 80,000 PSI
.... Yes
.................................... Yes
...................................................... 44 lbs.
..........................................................21 1⁄8"
................................................................6"
............................................................4 7⁄8"
.................................................4 7⁄8"
......... 12 1⁄4"
.........................................................6"
.....................................................3 1⁄4"
..............................6,744 lbs.
....................................... 7,41 8 l bs.
............................ Yes
.......................1:1
....................HRC 45°
............................. Ductile Iron FCD60
........................ 80,000 PSI
.... Yes
.................................... Yes
..................................................... 116 lb s.
COPYRIGHT © SEPTEMBER, 2012 BY GRIZZLY INDUSTRIAL, INC., REVISED MARCH, 2021 (CS)
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Vise is very heavy! Get another person to help you or use hoist when lifting or plac­ing vise. Wear heavy-duty leather boots for foot and toe protection, and keep hands and fingers away from all pinch points. Ignoring this warning can lead to severe pinching or crushing injuries!
Figure 3. Opening jaws.
Standard Operation
To open vise:
Rotate handle counterclockwise to open vise
1.
jaws. Step-side jaws (see Figure 2) will open slightly first, then fore-side will open.
Fore-Side
Step-Side
Fixed Center
Handle
To close vise:
1.
Rotate handle clockwise to bring vise jaws
back toward center. Fore-side jaws will move first, stopping after lightly clamping fore-side workpiece. Step-Side jaws will then begin to close.
Once both sides contact their workpieces,
2.
apply final tightening pressure. Force will automatically be evenly distributed to both sides (see Figure 4).
Figure 2. Identifying vise sides.
2. Once fore-side has opened completely, step-
side will resume opening. Continue opening until there is adequate room to insert work­piece (see Figure 3). T10065 has maximum clamping range of 3 1⁄2" using fixed center jaw, while T10066 can clamp up to 4 7⁄8".
Note: There will be increased resistance
when turning handle once fore-side has been opened completely and step-side begins to open. This is normal.
-2-
Workpieces
Figure 4. Tightening workpieces.
Once work has been completed, rotate han-
3.
dle counterclockwise to open jaws. As when previously opening jaws, step-side opens slightly first before fore-side opens.
Note: Step-side jaws will always open slightly
before fore-side jaws. Step-side jaws will
5
always open between
16"– 3⁄8".
Model T10065/66 (Mfd. Since 2/21)
Removing Fixed Jaw & Securing Step-Side
By reconfiguring the jaws and jaw plates, this vise can be adapted to handle almost any type of workpiece. The fixed center jaw can be removed and the step-side made stationary to clamp larger workpieces.
Tools Needed Qty
Hex Wrench 8mm (T10065) .............................. 1
Hex Wrench
To remove fixed jaw and secure step-side:
1.
Remove (2) cap screws attached to top of
fixed jaw and remove jaw (see Figure 5).
3
/8" (T10066) ................................. 1
Fixed
Jaw
Replacing Vise Jaws
The fore and step-side jaws can also be removed along with the center, and replaced with machin­able soft jaws. Soft jaws offer the precision of hardened parallel blocks, and can be easily machined back to perfection after frequent use.
In addition to the soft jaws offered by Grizzly, many vise owners prefer to custom make their own soft jaw sets out of aluminum, customizing grooves and steps (often referred to as "jack blocks") directly onto the soft jaws.
Tools Needed Qty
Hex Wrench 8mm (T10065) .............................. 1
Hex Wrench
To replace jaws:
1. Remove locking pin from side of desired jaw
and remove set screw used to adjust jaw against leadscrew nut (see Figure 7). Lift jaw directly up to remove.
3
/8" (T10066) ................................. 1
Figure 5. Removing center jaw.
Open vise until outer edge of step-side is
2.
flush with matching edge of vise body.
Attach step-side lock plate to step-side and
3.
vise body using (6) 3⁄8"-16 x 11⁄2" cap screws that came with vise (see Figure 6).
Note: Model T10066 uses 1⁄2"-13 x 1 3⁄4" cap
screws.
Lock
Plate
Replacement
Jaws
Locking
Pin
Figure 7. Changing jaws.
Set alternate jaw (sold separately) down on
2.
leadscrew nut. Thread in adjusting set screw and insert locking pin.
Apply directions listed in Removing Fixed
3. Jaw & Securing Step-Side section to
remove and replace center jaw.
Figure 6. Attaching step-side lock plate.
Model T10065/66 (Mfd. Since 2/21)
-3-
Replacing & Moving Jaw Plates
Jaw plates are also interchangeable and can be used in a variety of ways. Additionally, jaw plates can be bolted onto the opposite ends of the step and fore-side jaws, enhancing the overall clamp­ing range of the vise.
Tools Needed Qty
Hex Wrench 8mm (T10065) .............................. 1
Hex Wrench
To change jaw plates:
Remove (2) cap screws holding jaw plate to
1.
jaw (see Figure 8).
Replace original jaw plate with alternate plate
2.
(sold separately) and tighten into place (see Figure 8).
Remove
Existing
Jaw Plate
3
/8" (T10066) ................................. 1
x 2
Accessories
SB1284 —4" Step Jaw for T10065 SB1286 —6" Step Jaw for T10066
These step jaws hold flat stock and are direct jaw plate replacements for your milling vise. They are precision-ground and flame-hardened for added accuracy and durability. Sold in pairs.
Figure 9. 4" and 6" step jaws for milling vises.
SB1287—4" V Jaw for T10065 SB1289 —6" V Jaw for T10066
These jaws feature horizontal and vertical V-grooves to secure round stock parallel or per­pendicular to vise during operation. They are precision-ground and flame-hardened for added accuracy and durability.
Alternate
Jaw Plate
Figure 8. Removing and replacing jaw plates.
Note: Jaw plates can also be attached to
opposite ends of jaws. This allows for wider clamping area when working with extra-long narrow workpieces (see Common Clamping Arrangements on Page 5).
Figure 10. 4" and 6" V jaws for milling vises.
-4-
Model T10065/66 (Mfd. Since 2/21)
Common Clamping Arrangements
= Jaw Plate
Figure 11. Clamping two identical-sized
workpieces at once.
= Workpiece
Figure 14. Clamping thin workpieces of different
sizes with ridged jaw plates (sold separately).
Figure 12. Clamping two different-sized
workpieces at once.
Figure 13. Clamping single large workpiece by
removing center jaw.
Figure 15. Clamping multiple sizes and shapes
by repositioning jaw plates.
Figure 16. Clamping extra-long, thin workpieces.
Model T10065/66 (Mfd. Since 2/21)
-5-
Dimensional Specifications
A
B
h
c
H
C
i
C
D
g
d
e
Model
T10065
T10066
a
j
Length Specifications (in inches)
A
4.05 1.29 3.54 1.49 15.9 4.09 3.99 2.5 0.68 0.51 1.22 3.79 2.5 1.85 16.9 5.62 7.67 44 lbs.
5.98 1.6 4.9 1.75 20.47 6 4.98 3.87 0.94 0.7 0.63 4.86 3.25 2.52 25.15 7.59 9.64 116 lbs.
C
B
D
a b c d e f g h
f
H
i j
b
k
l
k l
Weight
Inspection Specifications
Parallelism: Squareness:
Running face to bottom of bed
G
Guaranteed: 0.0004"
G
Keyways on bottom of bed to jaw plate
Keyways on bottom of bed to jaw
Guaranteed: 0.0008"
Between running face to jaw plate
-6-
Guaranteed: 0.0006"
Running face of the test block to bottom
Guaranteed: 0.0008"
Guaranteed: 0.0006"
Model T10065/66 (Mfd. Since 2/21)
T10065 Parts Breakdown & List
REF PART # DES CRIP TIO N REF P ART # DES CRIP TIO N
35
28
26
30
36
41
33
34
27
33
34
26
32
34
22
33
34
33
31V2
25
21
20
27
30
23
28
35
24A
24
21 20
4
7
1V2
40
3
29
2
5
8
2
3
37
40
38
16
17
10
11
12
13
6
10A
29
39
42
43
44
15
18
1V2 PT10065001V2 VISE BASE V2. 02.21 24 PT10065024 STATI O NARY CHI P G UARD 2 PT10065002 RAIL CAP 4-PC 25 PT10065025 CHIP GUA RD CLI P 3 PT10065003 FLAT HD CAP SCR 1/4-20 X 1/2 26 PT10065026 SET SCREW M8-1.25 X 16 BALL PT 4 PT10065004 VI SE LEADSCREW 27 PT10065027 MOVABLE JAW 2-PC 5 PT10065005 FO RE- SI DE LE ADS CREW NUT 28 PT10065028 LOCKING PIN 2-PC 6 PT10065006 STEP-SIDE LEADSCREW NUT 29 PT10065029 LEADSCREW NUT SLEEVE 2-PC 7 PT10065007 CAP SCREW 1/4-20 X 3-1/2 30 PT10065030 SET SCREW 3/8-16 X 5/ 8 8 PT10065008 STEP-SIDE COMPRESSION SPRING 2-PC 31V2 PT10065031V2 FIXED JAW V2.02. 21 10A PT10065010A ADJUSTING LEADSCREW STOPPER ASSEMBLY 32 PT10065032 HEX BOLT 3/8-16 X 1-1/2 10 PT10065010 ADJUSTING LEADSCREW STOPPER 33 PT10065033 JAW PLATE 4-PC 11 PT10065011 STOPPER ADJUSTMENT PIN 34 PT10065034 CAP SCREW 3/8-16 X 1/ 2 12 PT10065012 COLLAR 11.8MM 35 PT10065035 KNOB BOLT M8-1.25 X 38 13 PT10065013 DISC SPRING 12 X 5.2MM 36 PT10065036 STEP-SIDE LOCK PLATE 15 PT10065015 LEADSCREW STOPPER BRAKE 37 PT10065037 HANDLE ASSEMBLY 16 PT10065016 SET SCREW M8-1 X 12 CONE PT 38 PT10065038 SET SCREW 1/4-20 X 1/ 4 17 PT10065017 COMPRESSION SPRING 39 PT10065039 CAP SCREW 3/8-16 X 1-1/ 2 18 PT10065018 ROLL PIN 4 X 30 40 PT10065040 MILL TABLE GUIDE BLOCK 2-PC 20 PT10065020 SEGMENTED COIL SPRING 4-PC 41 PT10065041 MILL TABLE CLAMP KIT 4-PC 21 PT10065021 PHLP HD SCR M3-.5 X 6 42 PT10065042 HEX WRE NCH 3/ 1 6 22 PT10065022 FORE-SIDE SLIDING CHIP GUARD 43 PT10065043 HEX WRE NCH 4MM 23 PT10065023 STEP-SIDE SLIDING CHIP GUARD 44 PT10065044 HEX WRE NCH 8MM 24A PT10065024A STA TI ONA RY CHI P GUA RD W/ CLI P
Model T10065/66 (Mfd. Since 2/21)
-7-
T10066 Parts Breakdown & List
REF P ART # DES CRIP TIO N REF P ART # DES CRIP TIO N
35
26
30
36
34
33
27
26
32
33
34
34
28
33
22V2
41
33
31V2
24AV2
25V2
24V2
27
30
23V2
34
38
3
5V2
2
1V2
40
2
40
3
29
6V2
10
11
14
14
13
12
10A
37
16
17
19
1V2 PT10066001V2 VISE BASE V2. 02.21 24AV2 PT10066024AV2 STATIONARY CHIP GUARD W/CLIP V2. 02.21 2 PT10066002 RAIL CAP 4-PC 24V2 PT10066024V2 STATIONARY CHIP GUARD V2.02.21 3 PT10066003 FLAT HD CAP SCR 1/4-20 X 1/2 25V2 PT10066025V2 CHIP GUARD CLIP V2.02.21 4 PT10066004 VI SE LEADSCREW 26 PT10066026 SET SCREW M8-1.25 X 16 BALL PT 5V2 PT10066005V2 FORE-SIDE LEADSCREW NUT V2.02.21 27 PT10066027 MOVABLE JAW 2-PC 6V2 PT10066006V2 STEP-SIDE LEADSCREW NUT V2.02.21 28 PT10066028 LOCKING PIN 2-PC 7 PT10066007 CAP SCREW 5/16-18 X 4-1/2 29 PT10066029 LEADSCREW NUT SLEEVE 2-PC 8 PT10066008 STEP-SIDE COMPRESSION SPRING 30 PT10066030 SET SCREW 1/2-13 X 3/ 4 10A PT10066010A ADJUSTING LEADSCREW STOPPER ASSEMBLY 31V2 PT10066031V2 FIXED JAW V2.02.21 10 PT10066010 ADJUSTING LEADSCREW STOPPER 32 PT10066032 CAP SCREW 7/16-14 X 2 11 PT10066011 STOPPER ADJUSTMENT PIN 33 PT10066033 JAW PLATE 4-PC 12 PT10066012 COLLAR 16MM 34 PT10066034 CAP SCREW 1/2-13 X 3/4 13 PT10066013 UPPER DISC SPRING 16 X 8.2MM 35 PT10066035 KNOB BOLT M8-1.25 X 38 14 PT10066014 LOWER DISC SPRING 16 X 0.8MM 36 PT10066036 STEP-SIDE LOCK PLATE 15 PT10066015 LEADSCREW STOPPER BRAKE 37 PT10066037 HANDLE ASSEMBLY 16 PT10066016 SET SCREW M12-1.25 X 20 CONE PT 38 PT10066038 SET SCREW 5/16-18 X 5/ 16 17 PT10066017 COMPRESSION SPRING 39 PT10066039 CAP SCREW 1/2-13 X 1-3/ 4 18 PT10066018 ROLL PIN 4 X 30 40 PT10066040 MILL TABLE GUIDE BLOCK 2-PC 19 PT10066019 L EA DSCRE W HANDL E S HROUD 41 PT10066041 MILL TABLE CLAMP KIT 4-PC 22V2 PT10066022V2 FORE-SIDE SLIDING CHIP GUARD V2.02. 21 42 PT10066042 T-HA NDLE HEX WRENCH 6 MM 23V2 PT10066023V2 STEP-SIDE SLIDING CHIP GUARD V2.02.21 43 PT10066043 HEX WRE NCH 3/ 8
18
15
28
35
43
4
7
8
29
42
39
-8-
Model T10065/66 (Mfd. Since 2/21)
Loading...