Grizzly H5528, H5529 User Manual

This gravity feed spray gun includes a 1.4mm nozzle, a durable 600cc cup, an air adjust valve, and a chrome finish for easy clean-up.

Figure 1. Spray gun controls.

Fluid

Control

Nozzle

Control

Paint

Reservoir

Pattern Control

Air Flow

Control

Model H5528 & H5529

Medium Duty Spray Gun

SETUP

1. Thread the paint reservoir onto the top of the

spray gun and attach the airline with a

⁄4" NPT

fitting.

2. Adjust the air pressure so that the gun is

supplied with 30 PSI.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

PRINTED IN CHINA

ADJUSTMENTS

Identify the spray gun controls in Figure 1 and adjust in the following order:

1. Fluid Control—Adjusts how far back the

trigger can be pulled, which affects the volume of finish released.

2. Air Flow Control—Adjusts the volume of air

that mixes with the finish, and thus, increases or decreases the finish atomization.

3. Pattern Control—Variably adjusts the spray

pattern from round to a wide fan.

4. Nozzle Control—Adjusts the spray pattern

from vertical to horizontal.

OPERATION

Hold the sprayer 6"–8" from the workpiece, and keep the spray gun perpendicular to the workpiece during strokes. DO NOT pivot your wrist when spraying! Feather strokes by starting your stroke before triggering the spray gun, and releasing the trigger before finishing the stroke. Overlap strokes by 50%

MAINTENANCE

1. Clean the spray gun passages after each use

by spraying a small amount of thinner. DO NOT immerse the spray gun in the thinner.

2. To avoid internal damage, use only the

included brush soaked with thinner when cleaning inside the spray gun.

3. Regularly clean the filter between the

reservoir and the spray gun.

4. Trigger, control valves, and springs should be

lubricated periodically.

EXPLOSION HAZARD! Do not spray flammable fluids near an open flame or ignition source.

RESPIRATORY HAZARD! Always wear a respirator rated for paint and solvent vapors when operating the H5528 and H5529 Spray Guns.

If you need additional help with these procedures, call our service department at: (570) 546-9663.

H5528 & H5529 Parts Diagram

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PH5528001 BREATHER PLUG 2 PH5528002 RESERVOIR COVER 3 PH5528003 PLASTIC RESERVOIR 4 PH5529004 ALUMINUM RESERVOIR 5 PH5528005 FILTER 6 PH5528006 FLUID INLET JOINT SEAL 7 PH5528007 FLUID INLET JOINT 8 PH5528008 HANGER 9 PH5528009 FLUID ADJ. NEEDLE 10 PH5528010 FLUID NEEDLE SPRING 11 PH5528011 JOINT CAP 12 PH5528012 FLUID ADJ. KNOB 13 PFH31M FLAT HD SCR M6-1 X 8 14 PH5528014 PATTERN ADJ. KNOB 15 PH5528015 PATTERN ADJ. KNOB 16 PH5528016 COPPER WASHER 8MM 17 PH5528017 PATTERN ADJ. SCREW 18 PH5528018 O-RING 19 PEC09M E-CLIP 6MM 20 PH5528020 AIR INLET PLUG 21 PH5528021 MULTI-TOOL WRENCH 22 PH5528022 HEX SOCKET TOOL 23 PH5528023 BRUSH 24 PH5528024 AIR ADJ. SCREW 25 PH5528025 AIR ADJ. KNOB

26 PH5528026 O-RING 27 PH5528027 DOMED SEAL WASHER 28 PH5528028 AIR ADJ. SPRING 29 PH5528029 AIR INLET VALVE 30 PH5528030 SWITCH SPRING 31 PH5528031 AIR VALVE BODY 32 PH5528032 SWITCH KNOB 33 PH5528033 O-RING 34 PH5528034 DOMED SEAL WASHER 35 PH5528035 DIRECTION SCREW 36 PH5528036 LOCKED SPRING 37 PH5528037 NOZZLE NUT 38 PH5528038 SEAL WASHER 30MM 39 PH5528039 ATOMIZATION 40 PH5528040 FLUID NOZZLE 41 PH5528041 FLUID NOZZLE PLUG 42 PH5528042 SEAL WASHER 10MM 43 PH5528043 DIRECTION SCREW 44 PH5528044 DOMED SEAL WASHER 45 PH5528045 SPRING 46 PH5528046 TRIGGER PIN I 47 PH5528047 TRIGGER PIN II 48 PH5528048 TRIGGER 49 PEC02M E-CLIP 4MM 50 PEC02M E-CLIP 4MM

1718

3 (H5528) 4 (H5529)

29 28

30313233

25 24