COPYRIGHT © OCTOBER, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
ELECTRIC 3⁄16" CROWN STAPLER
MODEL H3119
INSTRUCTION MANUAL
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and
other masonry products.
• Arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter out microscopic particles.
H3119 Electric 3⁄16" Crown Stapler
SAFETY
-1-
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY
result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
NOTICE
Safety Instructions
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from winch
before operation.
3. KEEP CHILDREN AWAY. All children should be kept at a safe distance from winch.
4. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
5. NEVER ALLOW UNTRAINED
USERS TO RUN THIS TOOL
WHILE UNSUPERVISED.
6. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear protective
hair covering to contain long hair.
7. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if
cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they are NOT safety
glasses.
8. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL.
H3119 Electric 3⁄16" Crown Stapler
-2-
9. USE PROPER EXTENSION CORD
for the tool. Make sure your extension cord is in good condition.
Conductor size should be in accordance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
Minimum Gauge for Extension Cords
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving
parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
Safety Instructions For Power Tools
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s
manual for recommended accessories. The use of improper accessories may cause risk of injury.
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
AMP LENGTH
RATING 25ft 50ft 100ft
0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 12 10
21-30 10 10 No
No list of safety guidelines can be
complete. Operating this tool may
require additional safety precautions specific to your working
environment. Failure to use reasonable caution while operating
this tool could result in serious
personal injury.
H3119 Electric 3⁄16" Crown Stapler
-3-
INTRODUCTION
Commentary
We are pleased to provide this manual with
the Model H3119. It was written to encourage safety considerations and guide you
through general operating procedures and
maintenance. This manual represents our
effort to produce the best documentation
possible.
The specifications, details, and photographs in this manual represent the
Model H3119 as supplied when the manual was prepared. However, owing to
Grizzly’s policy of continuous improvement, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Grizzly Industrial, Inc.
C
/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com
We are proud to offer the Grizzly Model
H3119 Electric 3⁄16" Crown Stapler. This
model is part of a growing Grizzly family of
fine power tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.
The Model H3119 is a high powered electric stapler capable of firing 20 gauge, 3⁄16"
crown staples in lengths ranging from 1⁄4"
to 9⁄16". The quick loading magazine holds
85 staples and the weight is 3.25 lbs.
The Model H3119 is best suited for installation of carpet, insulation, ceiling tiles,
cabinets and HVAC systems.
Lack of familiarity with this manual
could cause serious personal injury.
Spend a sufficient amount of time
becoming familiar the contents of
this manual, including all the safety
warnings.
H3119 Electric 3⁄16" Crown Stapler
-4-
OPERATION
Getting Started
Please take the time to become familiar
with this instruction manual. The information contained will allow you to get the
maximum enjoyment and use from your
new tool.
Loading The Stapler
The Model H3119 can hold up to 85 staples in the quick loading magazine.
To load the stapler:
1. Unplug the tool from the power
source!
2. Press the silver lever while sliding back
on the staple magazine.
3. Point the tip of the stapler upward to
reveal the stapler loading area. The
loading area consists of a groove or
channel that runs along the bottom of
the stapler.
4. Load a stick of 20 gauge
3
⁄16" crown
staples 1⁄4" to 9⁄16" long into the loading
area.
5. Slowly slide the staple magazine back
into the closed position until the silver
lever latches in the closed position.
Using The Stapler
1. Be sure the stapler is loaded and the
magazine is closed securely.
2. Wear safety glasses when using the
stapler
3. Plug the stapler into a 110V power
source.
4. Place the tip of the stapler against the
workpiece and pull the trigger.
DO NOT pull the trigger until the tip
of the stapler is against the surface
to be stapled. The stapler does NOT
have a safety mechanism.
Avoid repeatedly shooting staples
into the exact same location without
moving the tip of the stapler. A staple
could become jammed in the tip of
the stapler.
H3119 Electric 3⁄16" Crown Stapler
-5-
Clearing Jammed Staples
Staple jams are an inevitable part of operating any stapler.
To clear a jammed stapler:
1. Unplug the tool from the power
source!
2. Open the staple magazine and remove
all un-jammed staples.
3. The jammed staple may be easily
removed at this time; otherwise, the
stapler tip will need to be disassembled.
4. To disassemble the tip, use an allen
wrench to remove the three allen head
cap screws from the face of the tip.
5. Once the screws are removed and the
staple magazine is open, the tip piece
should pull away from the stapler.
6. The jammed staple should now be
easy to remove.
7. Once the jammed staple is removed,
re-assemble the stapler.
Maintenance
Unplug the stapler from the power
source before performing any maintenance!
Cleaning The Stapler
While wearing safety glasses, periodically
clean the stapler with compressed air. DO
NOT use flammable products to clean the
stapler.
Gasoline or petroleum products used
to clean the tool could explode causing serious personal injury. DO NOT
use gasoline or petroleum products
to clean the tool.
H3119 Electric 3⁄16" Crown Stapler
-6-
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
techsupport@grizzly.com
Web Site: http://www.grizzly.com
Thank you again for your business and continued support. We hope to serve you again
soon!
WARRANTY AND RETURNS
H3119 Electric 3⁄16" Crown Stapler
-8-
01 PH3119001 CYLINDER CAP ASSEMBLY
02 PH3119002 PLUNGER
03 PH3119003 PIN
04 PH3119004 PLUNGER BLADE
05 PH3119005 PLUNGER RET. WASHER
06 PH3119006 RETURN SPRING
07 PH3119007 CLIP
08 PH3119008 LOCATOR RING
09 PH3119009 HANDLE (RIGHT)
10 PFH27
FLAT HD ALLEN SCR 8-32 X 3/4"
11 PLN09 LOCK NUT 8-32
12 PSB67 CAP SCREW 8-32 X 7/8"
13 PFH28
FLAT HD ALLEN SCR 8-32 X 1-5/16"
14 PH3119014 HANDLE (LEFT)
15 PH3119015 RING
16 PH3119016 COIL/WASHER ASSEMBLY
17 PH3119017 STAPLER BODY
18 PSB38 SCREW 10-32 X 3/8"
19 PH3119019 BUMPER
20 PH3119020 NOSE RETAINER
21 PH3119021 CLAMP
22 PSB68 CAP SCREW 10-32 X 1/2"
23 PSB33 SCREW 10-24 X 3/4"
24 PH3119024 PIN
25 PH3119025 NOSE
26 PH3119026 PIN
27 PH3119027 PUSHER
28 PH3119028 MAGAZINE BASE
29 PH3119029 SPRING
30 PH3119030 BASE
31 PH3119031 MAGAZINE SUPPORT
32 PH3119032 PIN
33 PH3119033 E-CLIP
34 PH3119034 SUPPORT SPACER
35 PSB41 SCREW 10-24 X 1/2"
36 PLN10 LOCK NUT 10-32
37 PH3119037 POWER SUPPLY
38 PLW08 LOCK WASHER #6
39 PS36 PHLP HD SCR 6-32 X 3/8"
40 PH3119040 INSULATION SLEEVING
41 PLN11 LOCK NUT 6-32
42 PH3119042 FUSE HOLDER
43 PSB69 CAP SCREW 6-32 X 3/8"
44 PH3119044 CORD ASSEMBLY
45 PH3119045 SWITCH PROTECTOR
46 PH3119046 SWITCH ASSEMBLY
47 PH3119047 CONTACT PIN
48 PH3119048 SPRING
49 PH3119049 TRIGGER BRACKET
50 PLW01 LOCK WASHER 5/16"
51 PN20 HEX NUT 5/16"-24
52 PH3119052 SPRING
53 PH3119053 CONTACT BUTTON
54 PH3119054 TRIGGER
55 PH3119055 RETAINING RING
56 PH3119056 TRIGGER PIN
57 PH3119057
CARRYING CASE (NOT SHOWN)
REF PART # DESCRIPTION
REF PART # DESCRIPTION
H3119 Electric 3⁄16" Crown Stapler
-9-
NOTES
H3119 Electric 3⁄16" Crown Stapler
-10-
NOTES
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #___________________________ Serial #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
WARRANTY CARD
9. How many of the machines checked above are
Grizzly? ____________
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander ___Orbital Sander
___Biscuit Joiner ___Palm Sander
___Circular Saw ___Portable Planer
___Detail Sander ___Saber Saw
___Drill/Driver ___Reciprocating Saw
___Miter Saw ___Router
___Other_________________________________
11. What machines/supplies would you like Grizzly
Industrial to carry?
________________________________________
________________________________________
________________________________________
________________________________________
12. What new accessories would you like Grizzly
Industrial to carry?
________________________________________
________________________________________
________________________________________
________________________________________
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
14. Do you think your purchase represents good value?
___Yes ___No
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We
never use names more than three times.
___Yes ___No
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
1. How did you learn about us?
___Advertisement ___Friend
___Catalog ___Card Deck
___World Wide Web
___Other__________________________
2. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
3. What is your age group?
___20-29 ___50-59
___30-39 ___60-69
___40-49 ___70 +
4. How long have you been a woodworker?
___0 - 2 Years ___8 - 20 Years
___2 - 8 Years ___20+ Years
5. How would you rank your woodworking skills?
___Simple ___Advanced
___Intermediate ___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
___Air Compressor ___Panel Saw
___Band Saw ___Planer
___Drill Press ___Power Feeder
___Drum Sander ___Radial Arm Saw
___Dust Collector ___Shaper
___Spindle Sander ___Jointer
___Table Saw ___Lathe
___Mortiser ___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
7. How many of your woodworking machines are
Grizzly? _____________
8. Which benchtop tools do you own? Check all
that apply.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw ___8" - 10" Bandsaw
___Scroll Saw ___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT NAIL
Name________________________________
Street________________________________
City______________State______Zip_______
Send a Grizzly Catalog to a friend:
Place
Stamp
Here
Loading...