Grizzly H0626 User Manual
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL H0626 OSCILLATING DRILL PRESS
Product Dimensions:
Weight.............................................................................................................................................................. 115 lbs.
Length/Width/Height............................................................................................................................. 24 x 15 x 38 in.
Foot Print (Length/Width)....................................................................................................................... 17-1/2 x 11 in.
Shipping Dimensions:
Type............................................................................................................................................................. Cardboard
Content............................................................................................................................................................Machine
Weight.............................................................................................................................................................. 127 lbs.
Length/Width/Height............................................................................................................................. 32 x 19 x 12 in.
Electrical:
Switch............................................................................................................. Paddle On/Off with Safety Lockout Key
Switch Voltage......................................................................................................................................................110V
Cord Length............................................................................................................................................................ 9 ft.
Cord Gauge....................................................................................................................................................18 gauge
Minimum Circuit Size........................................................................................................................................ 15 amp
Plug Included.......................................................................................................................................................... Yes
Motors:
Main
Type..................................................................................................................TEFC Capacitor Start Induction
Horsepower..............................................................................................................................................3/4 HP
Voltage........................................................................................................................................................110V
Prewired......................................................................................................................................................110V
Phase........................................................................................................................................................Single
Amps...............................................................................................................................................................9A
Speed.................................................................................................................................................1725 RPM
Cycle..........................................................................................................................................................60 Hz
Number Of Speeds........................................................................................................................................... 1
Power Transfer ............................................................................................................................... V-Belt Drive
Bearings.......................................................................................................................Shielded and Lubricated
Main Specifications:
Construction
Table Construction...................................................................................................Precision Ground Cast Iron
Spindle Housing Construction..............................................................................................................Cast Iron
Column Construction....................................................................................................Cylindrical Ground Steel
Head Construction................................................................................................................................Cast Iron
Base Construction................................................................................................................................Cast Iron
Paint..........................................................................................................................................................Epoxy
Head Information
Head Swivel..........................................................................................................................................360 deg.
The information contained herein is deemed accurate as of 10/6/2008 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 2Model H0626
Other Related Information
Base Length.........................................................................................................................................17-1/2 in.
Base Width.................................................................................................................................................11 in.
Quill Diameter........................................................................................................................................1.565 in.
No. Of Dust Ports..............................................................................................................................................1
Dust Port Size.............................................................................................................................................. 2 in.
Depth Stop Type.............................................................................................Threaded Rod with Positive Stop
Column Diameter.................................................................................................................................... 2.79 in.
Spindle Information
Spindle Taper............................................................................................................................................... B16
Spindle Travel........................................................................................................................................3-1/4 in.
Dist From Spindle To Column................................................................................................................6-3/4 in.
Dist From Spindle To Table................................................................................................................. 17-1/4 in.
Dist From Spindle To Base........................................................................................................................ 24 in.
Table Information
Table Diameter.....................................................................................................................................12-3/4 in.
Table Thickness...........................................................................................................................................1 in.
Floor To Table Height...............................................................................................................9-1/2 - 21-1/4 in.
Vertical Table Movement................................................................................................ Crank Handle Operate
Table Swing.......................................................................................................................................... 360 deg.
Table Tilt................................................................................................................................................. 90 deg.
Table Swivel Around Center................................................................................................................. 360 deg.
Table Swivel Around Column................................................................................................................360 deg.
Maximum Movement Of Work Table....................................................................................................11-3/4 in.
No. Of T Slots....................................................................................................................................................5
T Slot Width...............................................................................................................................................5/8 in.
T Slot Length................................................................................................................................................3 in.
Operation Information
Oscillating Stroke Length.......................................................................................................................... 3/4 in.
Swing................................................................................................................................................... 13-1/4 in.
Drilling Capacity........................................................................................................................... 3/4 in. in Steel
No Of Spindle Speeds.....................................................................................................................................12
Range Of Spindle Speeds..................250, 330, 380, 500, 590, 640, 980, 1530, 1600, 1870, 2580, 3050 RPM
Drill Chuck Type....................................................................................................................... JT33 Key Chuck
Drill Chuck Size.........................................................................................................................................5/8 in.
Other Specifications:
Country Of Origin ................................................................................................................................................China
Warranty ............................................................................................................................................................2 Year
Serial Number Location ................................................................................................................Data Label on Head
Assembly Time ...........................................................................................................................................30 minutes
Features:
Includes Sanding Kit with 1", 1-1/2", & 2" Drums, Mandrel Washers, and 80 Grit Sanding Sleeves
Sanding Drum Shaft
Dust Collection Fitting
Oscillating Spindle
12 Speeds
3/4HP Motor
1/8" - 5/8" Chuck
Cushioned Grip Quill Handles
The information contained herein is deemed accurate as of 10/6/2008 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 2Model H0626
Loading...