Grizzly H0602 User Manual

COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.

1821 VALENCIA ST., BELLINGHAM, WA 98227

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

PRINTED IN CHINA

12V CORDLESS VACUUM

MODEL H0602

INSTRUCTION MANUAL

H0602 12V Cordless Vacuum

-1-

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

Indicates an imminently hazardous situation which, if
not avoided, WILL

result in death or serious injury.

Indicates a potentially hazardous situation which, if
not avoided, COULD

result in death or serious injury.

Indicates a potentially hazardous situation which, if
not avoided, MAY

result in minor or moderate injury.

It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful information
about proper operation of the equipment.

The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres­sion of symbols is described below. Remember that safety messages by them­selves do not eliminate danger and are not a substitute for proper accident pre­vention measures.

NOTICE

Safety Instructions For Power Tools

5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors

should be kept a safe distance from
work area.

6. MAKE WORK SHOP CHILD
PROOF with padlocks, master

switches, or by removing starter
keys.

7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.

8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.

1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-

ing to see that keys and adjusting
wrenches are removed from tool
before turning on.

3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.

4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power

tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.

SAFETY

No list of safety guidelines can be
complete. Every shop environment is
different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage to
equipment or poor work results.

H0602 12V Cordless Vacuum-2-

9. USE PROPER EXTENSION CORD

for the charger. Make sure your
extension cord is in good condition.
Conductor size should be in accor­dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.

Minimum Gauge for Extension Cords

10. WEAR PROPER APPAREL. Do not

wear loose clothing, gloves, neck­ties, rings, bracelets, or other jewel­ry which may get caught in moving
parts. Non-slip footwear is recom­mended. Wear protective hair cover­ing to contain long hair.

11. ALWAYS USE SAFETY GLASSES.

Also use face or dust mask if cutting
operation is dusty. Everyday eye­glasses only have impact resistant
lenses, they are NOT safety glass­es.

12. SECURE WORK. Use clamps or a

vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.

13. DON’T OVERREACH. Keep proper

footing and balance at all times.

Safety Instructions For Power Tools

AMP LENGTH

RATING 25ft 50ft 100ft

0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 12 10
21-30 10 10 No

14. MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.

15. DISCONNECT TOOLS before ser-

vicing and changing accessories,
such as blades, bits, cutters, and
the like.

16. REDUCE THE RISK OF UNINTEN­TIONAL STARTING. Make sure

switch is in off position before plug­ging in.

17. USE RECOMMENDED ACCES­SORIES. Consult the owner’s man-

ual for recommended accessories.
The use of improper accessories
may cause risk of injury.

18. CHECK DAMAGED PARTS.

Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate proper­ly and perform its intended function.
Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.