Grizzly H0588 User Manual

EYE INJURY HAZARD!

Quick Connector

Quick Coupler

Air Hose

Quick Coupler

Quick Connector

Lubricator

Filte

Regulato

Air

Compressor

Your Tool

Always wear safety glasses when using this tool to prevent serious personal

INJURY HAZARD! Always disconnect tool from air to prevent unexpected operation during service.

EXPLOSION HAZARD!

Never exceed 120 PSI.

MODEL H0588

⁄4" ANGLE DIE GRINDER

INSTRUCTION SHEET

Figure 1. Model H0588.

Introduction

Angle Die Grinders are excellent for reaching sideways into areas that are relatively confined. No-load speed is 18,000 RPM and collet size is

⁄4". Requires 90 PSI with 4 CFM of compressor

capacity. Air inlet is

⁄4" and air exhaust is in the

rear. Weighs just over 1 lb.

Inventory

A. Die Grinder ................................................. 1

B. Flat Wrench 17mm ..................................... 1

C. Flat Wrench 12mm ..................................... 1

Operation

Tool requires 90 PSI to operate correctly.

To improve tool lifespan, use a filter/lubricator/ regulator as shown in Figure 2. Otherwise, lubri cate daily with a couple drops of pneumatic tool oil directly into the air fitting as shown in Figure 3

Figure 2. Installing your tool.

Figure 3. Lubricating directly into air fitting.

If you need help with your new pneumatic tool, call our Tech Support at: (570) 546-9663.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#KM7957 PRINTED IN TAIWAN

H0588 Parts Breakdown and List

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PH0588001 MOTOR HOUSING 20 PH0588020 MOTOR CLAMP 2 PH0588002 THROTTLE VALVE 21 PH0588021 HOUSING CAP 3 PH0588003 THROTTLE VALVE SPRING 22 PH0588022 ANGLE HEAD HOUSING 4 PH0588004 AIR REGULATOR 23 PH0588023 REAR SPINDLE BALL BEARING 5 PH0588005 O-RING 24 PH0588024 SPINDLE GEAR 6 PH0588006 O-RING 25 PH0588025 FRONT SPINDLE BALL BEARING 7 PH0588007 VALVE SCREW 26 PH0588026 WOODRUFF KEY 8 PH0588008 THROTTLE LEVER 27 PH0588027 SPINDLE 9 PH0588009 THROTTLE LEVER PIN 28 PH0588028 CLAMP NUT 10 PH0588010 REAR ROTOR BALL BEARING 29 PH0588029 COLLET 11 PH0588011 REAR END PLATE 30 PH0588030 COLLET NUT 12 PH0588012 BALL 31 PH0588031 THROTTLE VALVE BUSHING 13 PH0588013 ROTOR COLLAR 32 PH0588032 O-RING 14 PH0588014 CULINDER 33 PH0588033 FLAT WRENCH 15 PH0588015 ROTOR 34 PH0588034 EXHAUST SLEEVE 16 PH0588016 ROTOR BLADE 35 PH0588035 AIR INLET 17 PH0588017 FRONT END PALTE 36 PH0588036 FLAT WRENCH 18 PH0588018 FRONT ROTOR BALL BEARING 37 PH0588037 BALL 19 PH0588019 PINION GEAR