COPYRIGHT © MARCH, 2002 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
THREE SPINDLE SHAPER
MODEL G9933
INSTRUCTION MANUAL
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and
other masonry products.
• Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
Table Of Contents
PAGE
1. SAFETY
SAFETY RULES FOR ALL TOOLS ......................................................................2-3
ADDITIONAL SAFETY INSTRUCTIONS FOR SHAPERS ......................................4
2. CIRCUIT REQUIREMENTS ............................................................................................5
G9933 OPERATION..................................................................................................5
GROUNDING & EXTENSION CORDS ....................................................................5
3. GENERAL INFORMATION ............................................................................................6
COMMENTARY ........................................................................................................6
UNPACKING..............................................................................................................7
PIECE INVENTORY ..................................................................................................7
CLEAN UP ................................................................................................................8
SITE CONSIDERATIONS ........................................................................................8
4. ASSEMBLY ....................................................................................................................9
BEGINNING ASSEMBLY ..........................................................................................9
DUST PORT ADAPTER ............................................................................................9
GUARD ASSEMBLY ..............................................................................................10
POWER CORD........................................................................................................10
5. ADJUSTMENTS............................................................................................................11
PULLEYS & V-BELTS ............................................................................................11
V-BELT TENSION ..................................................................................................12
CUTTERHEAD OPENING ......................................................................................12
SPEED CHANGES..................................................................................................13
FENCE ADJUSTMENT ..........................................................................................14
ALIGNING THE FENCE ..........................................................................................14
TABLE INSERTS ....................................................................................................15
HOLD-DOWNS ........................................................................................................15
SPINDLE CHANGES ..............................................................................................16
CUTTER INSTALLATION........................................................................................17
MITER GAUGE........................................................................................................17
TEST RUN ..............................................................................................................18
6. OPERATIONS ..............................................................................................................19
ROTATION ..............................................................................................................19
SPINDLE HEIGHT ..................................................................................................20
STRAIGHT SHAPING ........................................................................................20-21
RUB COLLARS ......................................................................................................22
PATTERN WORK & JIGS ......................................................................................23
7. MAINTENANCE ............................................................................................................24
GENERAL................................................................................................................24
TABLE......................................................................................................................24
LUBRICATION ........................................................................................................25
V-BELT ....................................................................................................................25
SCHEDULE ............................................................................................................25
WIRING DIAGRAM..................................................................................................26
8. CLOSURE ....................................................................................................................27
MACHINE DATA......................................................................................................28
PARTS BREAKDOWN AND PARTS LISTS ......................................................29-33
WARRANTY AND RETURNS ................................................................................34
-2- G9933 Three Spindle Shaper
Safety Instructions For Power Tools
SECTION 1: SAFETY
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should be
kept a safe distance from work area.
6. MAKE WORKSHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
7. NEVER FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
8. USE RIGHT TOOL. Do not force tool or
attachment to do a job for which it was not
designed.
1. KEEP GUARDS IN PLACE and in working
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. NEVER USE IN DANGEROUS ENVIRONMENT. Do not use power tools in
damp or wet locations, or where any flammable or noxious fumes may exist. Keep
work area well lighted.
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
Indicates an imminently hazardous situation which, if not
avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, MAY
result in minor or moderate injury. It may also
be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words which are intended to convey the level
of importance of the safety messages. The progression of symbols is described below.
Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
NOTICE
G9933 Three Spindle Shaper -3-
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage
rating should be listed on the motor or tool
nameplate. An undersized cord will cause a
drop in line voltage resulting in loss of
power and overheating. Your extension
cord must also contain a ground wire and
plug pin. Always repair or replace extension cords if they become damaged.
Minimum Gauge for Extension Cords
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear
is recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than
using your hand and frees both hands to
operate tool.
13. NEVER OVERREACH. Keep proper foot-
ing and balance at all times.
LENGTH
AMP RATING 25ft 50ft 100ft
0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 12 10
21-30 10 10 No
Safety Instructions For Power Tools
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing
and changing accessories, such as blades,
bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off
position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended accessories. The use of improper
accessories may cause risk of injury.
18. CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged should be properly
repaired or replaced.
19. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Do not
leave tool until it comes to a complete stop.
20. NEVER USE UNDER THE INFLUENCE of
alcohol or drugs, or when tired.
21. NEVER ALLOW UNSUPERVISED OR
UNTRAINED PERSONNEL TO OPERATE THE MACHINE. Make sure any
instructions you give in regards to the
operation of the machine are approved,
correct, safe, and clearly understood.
-4- G9933 Three Spindle Shaper
1. NEVER ALLOW YOUR HANDS to come
within 12 inches of the cutters. Never pass
your hands directly over or in front of the
cutter.
2. BLIND CUT WHENEVER POSSIBLE. This
keeps the knives on the underside of the
workpiece and provides a distance guard
for the operator.
3. WHEN SHAPING CONTOURED WORK
and using a rub collar, NEVER start out at a
corner. See the “Rub Collar” instructions
further on in the manual.
4. WITH THE MACHINE UNPLUGGED,
always rotate the spindle by hand with any
new setup to ensure proper cutter clearance before starting the machine.
5. DO NOT SHAPE STOCK SHORTER than
12 inches without special fixtures or jigs.
Where practical, shape longer stock and cut
to size.
6. NEVER ATTEMPT to remove too much
material in one pass. You are far more likely to enjoy safer and higher quality results if
you allow the cutter to remove material in
multiple passes.
7. THE DANGER OF kickback is increased
when the stock has knots, holes, or foreign
objects in it. Warped stock should be run
through a jointer before attempting to run it
through a shaper.
8. KEEP THE UNUSED PORTION of the cut-
ter below the table surface.
9. THE USE OF PUSH STICKS as safety
devices in some applications is smart; in
others it can be quite dangerous. If the push
stick comes in contact with the cutter on the
end grain, it can fly out of your hand like a
bullet—potentially causing serious injury.
We recommend using some type of fixture,
jig, or hold-down device as a safer alternative. Use a guard or other type of protective
device at all times.
10. NEVER FORCE MATERIALS through the
shaper. Let the cutters do the work.
Excessive force is likely to result in poor cutting results and will cause dangerous kickback conditions.
11. ALWAYS ensure that the cutters or bits,
fence, and spindle elevator knob have been
tightened properly before beginning any
operation.
12. ALWAYS feed the work toward the cutters
in the direction opposite of the cutter rotation. Also, using and maintaining a sharp
cutterhead will greatly reduce the chance of
kickback.
13. IF AT ANY TIME YOU ARE EXPERIENCING DIFFICULTIES PERFORMING THE
INTENDED OPERATION, STOP USING
THE SHAPER! Then contact our service
department or ask a qualified expert how
the operation should be performed.
Additional Safety Instructions For Shapers
Like all power tools, there is danger associated with shapers. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with
respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious
personal injury may occur.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious personal injury, damage to equipment or poor
work results.
G9933 Three Spindle Shaper -5-
SECTION 2: CIRCUIT REQUIREMENTS
G9933 Operation
The Model G9933 Shaper is furnished with 3
3450 R.P.M., 3 H.P., Single-Phase 220V motors,
a push-button ON/OFF magnetic starter switch, a
FORWARD/REVERSE switch for each motor and
a cord set. Under normal use, each motor draws
approximately 18 amps at 220V. We recommend
using a 30 amp circuit. This includes the appropriate wiring and circuit breaker. If frequent circuit
failures occur when using the shaper, contact our
service department.
The shaper must be connected to its own dedicated 30A circuit. It should not share a circuit with
any other machine. A standard 2-pole breaker is
necessary for use with the shaper.
We recommend using a NEMA-style L6-30 plug
and outlet similar to that in Figure 1. You may
also “hard-wire” the shaper directly to your panel,
provided you place a disconnect near the
machine. Check the electrical codes in your area
for specifics on wiring requirements.
Figure 1. Recommended plug configuration for
single-phase operation.
Grounding &
Extension Cords
In the event of an electrical short, grounding
reduces the risk of electric shock by providing a
path of least resistance to disperse electric current. This tool is equipped with an electric cord
that has an equipment-grounding conductor
which must be properly connected to a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Improper connections of the electrical-grounding
conductor can result in the risk of electric shock.
The conductor with green or green and yellow
striped insulation is the electrical-grounding conductor. If repair or replacement of the electric
cord or plug is necessary, do not connect the
equipment grounding conductor to a live terminal.
We do not recommend the use of extension
cords on 220V equipment. It is much better to
arrange the placement of your equipment and the
installed wiring to eliminate the need for extension cords. Should it be necessary to use an
extension make sure the cord is rated Hard
Service (grade S) or better. Refer to the chart in
Section 1: Safety to determine the minimum
gauge for the extension cord. The extension cord
must also contain a ground wire and plug pin.
Always repair or replace extension cords when
they become worn or damaged.
This equipment must be
grounded. Verify that any
existing electrical outlet
and circuit you intend to
plug into is actually
grounded. Under no circumstances should the
grounding pin from any
three-pronged plug be
removed. Serious injury
may occur.
-6- G9933 Three Spindle Shaper
SECTION 3: GENERAL INFORMATION
Grizzly Industrial, Inc. is proud to offer the Model
G9933 Shaper. This shaper is part of Grizzly’s
growing family of fine woodworking and metalworking machinery. When used according to the
guidelines stated in this manual, you can expect
years of trouble-free, enjoyable operation.
The Model G9933 is intended for heavy-duty professional use and is capable of cutting multiple
profiles without changing cutterheads.
The Model G9933 features three 3 H.P., 220V,
single-phase motors with magnetic power switching and full reversing capabilities. The Model
G9933
also offers a precision-ground cast iron
table, hold-down springs, and is capable of operating at 7000 and 10,000 R.P.M. A number of
optional accessories for the Model G9933 are
available. Please refer to the current Grizzly catalog for more information.
We are also pleased to provide this manual with
the Model G9933. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It represents our latest effort to produce the best documentation possible. If you have any criticisms
that you feel we should address in our next printing, please write to us at the address below:
Grizzly Industrial, Inc.
C
⁄O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227
Commentary
Most important, we stand behind our machines.
We have an excellent service department at your
disposal should the need arise. If you have any
service questions or parts requests, please call or
write to us at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone:(570) 546-9663
Fax:(800) 438-5901
E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G9933 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
Whenever possible, though, we send manual
updates to all owners of a particular tool or
machine. Should you receive one, we urge you to
insert the new information with the old and keep
it for reference.
Read the manual before
assembly and operation.
Become familiar with
the machine and it’s
operation before beginning any work. Serious
personal injury may
result if safety or operational information is not
understood or followed.
G9933 Three Spindle Shaper -7-
Unpacking
The shaper base unit (shown in Figure 2) is
shipped from the manufacturer in a carefully
packed carton. If you discover the machine is
damaged after you’ve signed for delivery, and the
truck and driver are gone, you will need to file a
freight claim with the carrier. Save the containers
and all packing materials for possible inspection
by the carrier or its agent. Without the packing
materials, filing a freight claim can be difficult. If
you need assistance determining whether you
need to file a freight claim, or with the procedure
to file one, please contact our Customer Service.
Piece Inventory
After all the parts have been removed from the
carton, you should have:
• Shaper Unit
• Miter Gauge
• Hardware (shown in Figure 3)
The Model G9933 Hardware:
Hardware Qty
Guard Assemblies 3
Dust Port Adapter 1
Set of 10 Hex Keys 1
11/13mm Combo Wrench 1
17/19mm Combo Wrench 1
Spindle Wrench 1
Spindle Key 1
Tool Box 1
10mm Flat Washers 6
10mm Lock Washers 6
1.5-10 x 30mm Hex Head Bolts 6
6mm Flat Washers 3
6mm Lock Washers 3
1.0-6 x 16mm Hex Head Bolts 3
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or, for the sake of expediency, replacements can be obtained at your local
hardware store.
When you are completely satisfied with the condition of your shipment, you should inventory its
parts.
Figure 3. Model
G9933
Hardware.
Figure 2. Model G9933 base unit.
The Model G9933 is a
heavy machine, 1270 lbs.
shipping weight. DO NOT
over-exert yourself while
unpacking or moving
your machine – use
power equipment to
move the machine.
Serious personal injury
may occur if safe moving
methods are not followed.
-8- G9933 Three Spindle Shaper
Clean Up
The unpainted surfaces are coated with a waxy
oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as
Grizzly’s G7895 Degreaser. Avoid chlorinebased solvents as they may damage painted surfaces should they come in contact. Always follow
the usage instructions on the product you choose
to clean.
Site Considerations
FLOOR LOAD
Your Model G9933 Shaper represents a large
weight load in a moderate sized footprint. Most
commercial shop floors will be adequate for the
1270 lb. weight of the Model G9933. Some floors
may require additional support. Contact an architect or structural engineer if you have any question about the ability of your floor to handle the
weight.
WORKING CLEARANCES
Working clearances can be thought of as the distances between machines and obstacles that
allow safe operation of every machine without
limitation. Consider existing and anticipated
machine needs, size of material to be processed
through each machine, and space for auxiliary
stands and/or work tables. Also consider the relative position of each machine to one another for
efficient material handling. Be sure to allow yourself sufficient room to safely run your machines in
any foreseeable operation.
LIGHTING AND OUTLETS
Lighting should be bright enough to eliminate
shadow and prevent eye strain. Electrical circuits
should be dedicated or large enough to handle
combined motor amp loads. Outlets should be
located near each machine so power or extension cords are not obstructing high-traffic areas.
Be sure to observe local electrical codes for proper installation of new lighting, outlets, or circuits.
Do not use gasoline or
other petroleum-based
solvents to clean with.
They have low flash
points which make them
extremely flammable. A
risk of explosion and
burning exists if these
products are used.
Serious personal injury
may occur.
Make your shop “child safe.”
Ensure that your workplace
is inaccessible to children by
closing and locking all
entrances when you are
away. Never allow visitors in
your shop when assembling,
adjusting, or operating
equipment.
Do not smoke while using
solvents. A risk of explosion or fire exists may
result in serious personal
injury.
Many of the solvents
commonly used to clean
machinery can be toxic
when inhaled or ingested. Always work in wellventilated areas far from
potential ignition sources
when dealing with solvents. Use care when disposing of waste rags and
towels to be sure they do
not create fire or environmental hazards.
G9933 Three Spindle Shaper -9-
SECTION 4: ASSEMBLY
Beginning Assembly
Most of your Model G9933 Shaper has been
assembled at the factory, but some parts must be
assembled or installed after delivery. We have
organized the assembly process into steps.
Please follow along in the order presented in this
section.
Dust Port Adapter
2. Fasten the dust port to the table, as shown in
Figure 5, with the 6mm-1.0 x 16mm hex
head bolts and 6mm flat washers.
Figure 5. Installing dust port.
Figure 4. Table mounting holes.
Keep clothing rolled up
and out of the way of
machinery and keep
hair pulled back.
Wear safety glasses during the entire assembly
process. Failure to comply may result in serious
personal injury.
Disconnect power to the
machine when performing any maintenance or
assembly. Failure to do
this may result in serious
personal injury.
Some die-cut metal parts may have sharp
edges (“flashing”) on them after they are
formed. Please examine the edges of all diecut metal parts before handling them.
Failure to do so could result in injury.
Dust Port
Adapter Holes
To install the dust port adapter on the table:
1. Line up the 3 holes on the dust port over the
3 holes (shown in Figure 4) in the center of
the table.
-10- G9933 Three Spindle Shaper
Guard Assemblies Power Cord
The Model G9933 comes with a guard assembly
for each of the 3 spindles. These come assembled complete with hold downs and fences. The
only set-up required is fastening them to the
table. To fasten the guard assemblies to the
table:
1. Slide the dust port on the back of the guard
assembly into the dust port adapter.
2. Line up the slots on the guard assembly with
the four closest holes to the spindle, and fasten the assembly to the table as shown in
Figure 6.
To connect a power cord to your Model G9933:
1. Locate the electrical box near the base of the
shaper.
2. Remove the two hex nuts and washers that
secure the cover on the electrical box.
3. Pull your power cord through the strain relief
on the electrical box cover.
4. Mirror the existing wires that are already
connected to the terminal. The smallest wire
(green) is the ground. Make sure the ground
from your power cord is across from the
ground wire on the shaper.
5. Insert each wire as shown on Figure 6A and
tighten the respective screws on the face of
the terminal block. The wires should now be
secure in each terminal. Give them a quick
test by tugging each one with mild pressure.
Do not pull too hard.
Figure 6. Fastening guard assembly to table.
Figure 6A. Connecting power cord to terminal block.
3. Repeat Steps 1 & 2 with the other two guard
assemblies.
6. Place the cover back over the terminal block
and secure it with the two washers and hex
nuts. Tighten the strain relief to the power
cord. See Section 2: Circuit Requirements
for plug information.
Shaper
Hot Hot
HotHot
Power Cord
Ground
Ground
G9933 Three Spindle Shaper -11-
Pulleys & V-Belts
SECTION 5: ADJUSTMENTS
Improper pulley alignment sharply reduces the
effectiveness of power transmission and belt life
expectancy. To align the pulleys:
1. Open the motor covers on the back of the
shaper cabinet to expose the motor and pulleys.
2. Check the alignment of each with a straight-
edge. If the pulleys are in alignment, the
straightedge should touch two sides of each
pulley evenly.
3. If pulleys are not in-line, loosen the motor
mount plate bolts shown in Figure 7, and
slide the motor up or down until the pulleys
are in line. To make this easier, use a bottle
jack to help in moving the motor up and
down or get help from a friend.
4. Tighten the motor plate bolts to secure the
motor after the pulleys are aligned.
Figure 7. Motor plate bolts.
Keep clothing rolled up
and out of the way of
machinery and keep
hair pulled back.
Wear safety glasses during the entire adjustment
process. Failure to comply may result in serious
personal injury.
Disconnect power to the
machine when performing any adjustments or
maintenance. Failure to
do this may result in serious personal injury.
-12- G9933 Three Spindle Shaper
Cutterhead Opening
The fence rails can be mounted on the fence
pieces in two ways. Figure 9 shows the incorrect
and correct way the rails should be mounted.
Figure 9. Correct fence rail position.
The correct position will allow the cutterhead
opening to travel from 0"-5
5
⁄8
". If the rail is
turned around or incorrect, the opening will
be restricted to 0"-3".
Incorrect
Correct
V-Belt Tension
The V-belts are small and run very fast; therefore,
the ideal deflection is
1
⁄4
" with moderate finger
pressure. The V-belts will slip if too loose, and will
squeal or cause vibration if too tight. Only adjust
the tension if necessary. To adjust one of the Vbelts:
1. Make sure the pulleys are properly aligned,
then loosen the hinge bolts that allow the
motor to swing toward and away from the
spindle pulley.
2. Adjust the position of the motor so it is either
closer or farther away than the spindle pulley, depending on if the V-belt was either too
loose or too tight.
3. Tighten the hinge bolts and test the tension.
4. Repeat steps 1-3 until the tension is correct.
G9933 Three Spindle Shaper -13-
Speed Changes
The Model G9933 Shaper is equipped with three
V-belt drive systems that control the speeds for
each of their respective spindles. To change spindle speeds:
1. Unplug the machine.
2. Loosen the V-belt by following the “V-Belt
Tension” instructions.
3. Select the desired speed. There are two
speeds for each spindle: 7000 and 10,000
R.P.M. Figure 8 shows the belt positions for
each available speed.
Figure 8. Spindle speed adjustment.
4. Align the belt along the appropriate pulley
grooves.
5. Swing the motor back into position and tight-
en the belt as discussed in the “V-Belt
Tension” instructions.
6. Tighten all the adjusting bolts.
7. Spin the pulley to ensure proper tracking.
Disconnect power to the
machine when performing any adjustments or
maintenance. Failure to
do this may result in serious personal injury.
-14- G9933 Three Spindle Shaper
Figure 11. Aligning fences with straightedge.
Aligning The Fence
The following procedure ensures that the fence is
parallel with itself and square with the table.
1. Check that the bolts through the wood facing
are tight on each side and adequately countersunk.
2. To align the wood facing, adjust one or both
fence halves so they are in close alignment.
Micro-adjust and check the alignment with a
straightedge as shown in Figure 11.
3. If the wood fences are not coplanar with
each other, shim the fence where it attaches
to the fence bracket until both fences are
coplanar.
Figure 10. Fence controls.
Fence Adjustment
The fence is a two-piece adjusting system. Each
fence is independently adjustable to compensate
for different cutting thicknesses and special shap-
ing applications. To adjust the fence see Figure
10 and follow the instructions below:
1. Loosen the fence lock handle.
2. Turn the fence adjustment knob until the
fence is set to the desired position.
3. Tighten the fence lock handle.
More detailed information concerning fence
adjustments is covered in the “Straight Shaping”
instructions.
Lock Handle
Adjustment Knob
G9933 Three Spindle Shaper -15-
Table Inserts
The Model G9933 is supplied with two inserts per
spindle. Use the smallest opening that a particular cutter will allow. This offers more support for
the workpiece and reduces the amount of chips
that can fall into the machine. The correct spindle
opening also allows any unused portion of the
cutter to remain below the table surface—
increasing operator protection. The largest insert
must be adjusted flush with the top of the table.
To adjust the insert:
1. For an accurate gauge, place a straightedge
across the top of the table insert and table
surface as shown in Figure 12.
2. Adjust each setscrew in the largest insert, so
the insert is flush with the surface of the
table.
3. Change the straightedge positions and
adjust the setscrews accordingly until the
entire circumference of the table insert is
flush with the table surface.
4. The smaller insert is designed to fit inside
and flush with the larger insert, so no further
adjustments are necessary once the larger
insert has been adjusted. However, clean
the inside lip of the larger insert before
installing the smaller insert so it will not raise
the it and cause problems.
Figure 12. Leveling table insert.
Figure 13. Hold-downs in place.
Hold-Downs
Hold-downs are used to hold the workpiece flat
on the table and snug against the fence as shown
in Figure 13.
It helps to periodically check the knob that
secures the hold-down bar to the guard to
make sure that it remains tight.
-16- G9933 Three Spindle Shaper
Spindle Changes
The spindles can be removed in order to change
sizes. It is important to always use the largest
spindle size possible for the cutter you have.
Always remove the cutters from the spindle
before changing spindles. To change spindles:
1. Unplug the shaper.
2. Place the spindle key over the spindle and
down inside the table as shown in Figure 14.
Rotate the key slowly until it locks into place.
Figure 14. Tightening spindle nuts.
3. Open the cabinet cover and engage the
spindle lock shown in Figure 15.
Figure 15. Spindle lock knob.
4. Rotate the spindle key counterclockwise to
remove the spindle.
5. Installation is the reverse of removal. When
inserting the new spindle, start it by hand
then use the spindle key to tighten it. Be sure
to release the spindle lock lever after installation is complete.
G9933 Three Spindle Shaper -17-
Miter Gauge
In the event that the miter gauge isn’t providing accurate cuts, it is important to ensure
that its gauge reads square to the fence at 0°.
To check this:
1. Lock the miter gauge at 0°.
2. Place a square flat along the face of the
miter gauge and slide it to the fence.
3. The square should be placed flat along both
the miter gauge face and the fence as shown
in Figure 17. If it is not, adjust the fence
accordingly.
Figure 17. Aligning fences with straightedge.
4. Repeat steps 1-3 for the other two sets of
fences.
Cutter Installation
Your shaper operates at speeds of 7000 and
10,000 R.P.M. 3
1
⁄2" or larger cutters must be
operated at the slowest speed. Always use the
largest spindle size possible. “Stacking” two
bushings inside each other in order to use a cutter two sizes bigger than the spindle will result in
a malfunction of cutter operation, which may
damage your equipment. To install a cutter:
1. Unplug the shaper.
2. Place the spindle wrench over the spindle
nut, and place a combo wrench on the spindle lock nut.
3. Loosen the spindle lock nut with the combo
wrench as shown in Figure 16.
Figure 16. Loosening spindle nuts.
4. Install the cutterhead onto the spindle. Use
spacers or collars so the configuration suits
your particular task. Refer to the “Rub Collar”
instructions further on in this manual for
ideas on the safest setup.
5. Place the spindle washer under the nut.
Screw on the nut and locknut.
6. Tighten the nuts while holding the spindle
stationary. Use a wrench on the notches at
the top of the spindle for leverage.
-18- G9933 Three Spindle Shaper
Once assembly is complete and adjustments are
done to your satisfaction, you are ready to start
the machine.
Turn on the power supply at the main panel.
Press the START button. Make sure that your finger is poised on the STOP button, just in case
there’s a problem. The shaper should run
smoothly with little or no vibration or rubbing noises. Strange or unnatural noises should be investigated and corrected before operating the
machine further.
Run the Model G9933 for a short time to ensure
that the moving parts are working properly with
no excessive vibration. If any problem develops,
correct it before attempting to use the machine.
If you cannot locate the source of unusual noises,
immediately contact our service department for
help.
Test Run
Never use the Model G9933 for applications
other than those for which it was intended.
DO NOT overload the machine or use
excessive force when shaping materials.
Severe personal injury, damage to the
machine, or damage to your workpiece
could occur.
Disconnect power to the
machine when performing any adjustments or
maintenance. Failure to
do this may result in
serious personal injury.
G9933 Three Spindle Shaper -19-
SECTION 6: OPERATIONS
Figure 18. Forward/reverse switch.
Rotation
Your shaper is equipped with a
FORWARD/REVERSE switch as shown in
Figure 18. In many instances, it will be necessary
to flip the cutter over and reverse cutter rotation.
Whenever possible, mount the cutter so the
board is milled on the bottom side. This does a
better job, and it is safer for the operator.
Always check the direction of cutter rotation before beginning any shaping operation.
Keep clothing rolled up
and out of the way of
machinery and keep
hair pulled back.
Wear safety glasses during all operations on the
shaper. Failure to comply may result in serious
personal injury.
Disconnect power to the
machine when performing any adjustments or
maintenance. Failure to
do this may result in serious personal injury.
Always wear a dust
mask when operating
the shaper. Using this
machine produces sawdust which may cause
allergic reactions or respiratory problems.
NOTICE
This machine was designed to be started
and stopped with the START/STOP buttons—not the reversing switch.
NOTICE
The following section was designed to give
instructions on the basic operations of this
shaper. However, it is in no way comprehensive of every shaper application. There
are many different jigs that can be built to
increase safety, accuracy, and types of
cuts. WE STRONGLY RECOMMEND that
you read books, trade magazines, or get formal training to maximize the potential of
your shaper.
-20- G9933 Three Spindle Shaper
The fence assembly is a two-piece, independently adjustable system. When removing material
from the whole face of your workpiece, the outfeed fence can be adjusted to provide support for
the workpiece as it passes over the cutter, or it
can be set in-line for partial face removal.
If removing material from the whole face,
observe the following steps:
1. Loosen the locking handles shown in Figure
20 that hold the fences in place.
Straight Shaping
Figure 20. Location of fence locking handles.
Spindle Height
To adjust the cutter height:
1. Loosen the spindle lock knob shown in
Figure 19.
2. Move the spindle up or down with the hand-
wheel until the desired position is obtained.
3. Lock the spindle into position.
Figure 19. Spindle height adjustment wheel.
The lock knob keeps the spindle in a fixed
position during shaper operation. Do not
over-tighten the lock knob. A snug fit is all
that is needed to keep the spindle from
moving during shaper use.
NOTICE
2. Adjust the infeed fence by turning the adjust-
ment knobs until the workpiece contacts the
cutter in the desired location.
3. Lock the infeed fence in position with the
locking handle. Use a test piece to determine
the best setting.
Read the entire manual
before making any cuts
with your shaper.
Serious personal injury
may result if safety or
operational information
is not understood or followed.
Lock Knob
G9933 Three Spindle Shaper -21-
4. Set the right and left wood face ends to
barely clear the cutter. This allows the maximum support possible. Remember to tighten down the wood facing before starting the
shaper.
5. When removing the entire face of the work-
piece, a test sample of the desired cut
should be advanced about 8'' then stopped.
6. Once the shaper is turned off and the cutter
has come to a complete stop, adjust the
outfeed fence to support the new profiled
edge as shown in Figure 21.
Figure 21. Fence adjusted to support workpiece.
If the face of the workpiece will only be partially
removed, observe the following steps:
1. Adjust the infeed fence to approximately
the desired depth of cut. Lock the infeed
fence in place.
2. Use a straightedge to adjust the outfeed
fence to the same plane as the infeed. Lock
the outfeed fence in place.
3. Set the right and left wood face ends so
they barely clear the cutter. This allows the
maximum support possible for the workpiece. Remember to tighten down the wood
facing before starting the shaper.
4. Run a test piece through the shaper as
shown in Figure 22.
Figure 22. Fence adjustment for blind cuts.
5. Always cut the end grain first when putting
an edge around the perimeter of your work-
piece. See Figure 23.
Figure 23. Sequence for multiple cuts.
-22- G9933 Three Spindle Shaper
Figure 25. Rub collar installed above cutter.
Figure 26. Rub collar between two cutters.
3. Between two cutters: Using a rub collar
between two cutters, as in Figure 26, has
the distinct advantage of performing two cuts
at once or eliminating the need to change
cutters for two different operations. Notice
that part of the edge is left uncut. The uncut
portion rides on the rub collar.
2. Above the cutter (preferred method—
safer): When the rub collar is used above
the cutter as seen in Figure 25, the cut can-
not be seen. This offers some advantage:
the stock is not affected by slight variations
in thickness and accidental lifting will not
damage the workpiece. If lifting occurs, simply correct the mistake by repeating the
operation.
Figure 24. Rub collar installed below cutter.
Rub Collars
Rub collars are used when shaping curved or
irregular workpieces, such as arched doors or
round table tops. Rub collars also limit the depth
of your cut.
There are two types of rub collars—solid and ballbearing. We recommend against the use of solid
rub collars. Grizzly carries an extensive line of
ball bearing rub collars designed for use with
Grizzly shapers. See the current catalog for listings.
It is possible to use the rub collars in any of the
following positions:
1. Rub collar below the cutter: When the rub
collar is used below the cutter as shown in
Figure 24, the progress of the cut can be
observed. However, any unintentional movement may lift the workpiece into the cutter,
damaging your work and possibly kicking the
workpiece back toward you with great force.
We do not recommend this position!
Whenever the cutterhead is above the
workpiece, or you can see it spinning during use, you must take extreme caution to
keep your hands away from the cutterhead.
Failure to do so may cause serious personal injury.
G9933 Three Spindle Shaper -23-
Jigs or fixtures must be solid, stable, and
secure; or kickback may occur, causing
personal injury.
2. Secure your workpiece on three sides with
toggle clamps, or fasten the workpiece to the
fixture with wood screws. Make sure they do
not protrude through the workpiece.
3. Ensure that clamps and hidden screws do
not come into contact with the cutter, and
design your fixture so that all cutting occurs
underneath the workpiece.
4. Always consider the cutting circle and rub
collar diameter for the correct cutting depth
when designing your pattern.
5. Make sure the workpiece rests flat on the
table, not on the fixture.
6. When cutting small pieces or cutting against
the grain, it is important to use safety jigs to
keep your hands farther away from the cutterhead and protect you from kickback.
Pattern Work & Jigs
When using a pattern, the rub collar can be positioned either above, below or between cutters.
The pattern is usually used when the entire edge
is to be shaped or when many duplicate pieces
are needed. Pattern work is particularly useful
when rough cutting irregular or oversize pieces
and then shaping the edge in a simple two-step
operation. A pattern can be incorporated into a
fixture by way of adding toggle clamps, hand
holds or other safety devices.
You have greater flexibility when choosing the
correct diameter rub collar for pattern work than
for non-pattern work. If you look at Figure 27,
you’ll notice that the position of the pattern determines the depth of cut. In other words, your pattern size is dependent upon the interrelationship
of the cutting circle, the desired amount of material removed, and the rub collar size. Changing
one or more of these will change the amount of
material removed. Planning ahead, you can best
decide which rub collars are best suited for your
application.
Figure 27. Rub collar determines depth of cut.
Figure 28. The right angle jig.
When making a pattern, jig, or fixture, here are a
few things to consider:
1. Use a material that will smoothly follow the
rub collar or fence, make the fixture stable,
and fasten the hand-holds to permit effective
operator support and safety.
Again, if you are unfamiliar with the use of jigs
and the various types available, read a shaper
book and/or get professional training. Also, many
jigs are available to purchase. The jig in Figure
28 shows an example of one type of jig available
through the Grizzly catalog.
Pattern
Rub Collar
-24- G9933 Three Spindle Shaper
Regular periodic maintenance on your Model
G9933 Shaper ensures its optimum performance.
Make a habit of inspecting your shaper each time
you use it.
Check for the following conditions and repair or
replace when necessary.
• Loose mounting bolts.
• Worn switch.
• Worn or damaged cords and plugs.
• Damaged V-belt.
• Any other condition that could hamper the
safe operation of this machine.
SECTION 7: MAINTENANCE
General
Table
The table and other non-painted surfaces on the
Model G9933 should be protected against rust
and pitting. Wiping the table clean after every use
ensures that wood dust isn’t allowed to trap moisture against bare metal surfaces.
Tables can be kept rust-free with regular applications of products like Boeshield
®
T-9. For long
term storage you may want to consider products
like Kleen Bore's Rust Guardit™.
Disconnect power to the
machine when performing any adjustments or
maintenance. Failure to
do this may result in serious personal injury.
G9933 Three Spindle Shaper -25-
V-Belt
Avoid getting grease or oil on the V-belts or pulleys. Check the V-belts, as part of a monthly
inspection for proper tension and belt condition.
Cracking and glazing could result in belt failure.
Replace the belt if such conditions appear.
Lubrication Schedule
The only parts on this machine that require periodic lubrication are the ways where the cartridge
slide rides on the elevation housing and where
the worm gears and bushings are located. Use a
light grease or anti-seizing compound on the
ways and worm gear, and give the shaft mount a
shot of light oil.
Regularly blow out air vents with compressed air
and keep exhaust port clear.
For every 1 hour of use, clean and spray an
application of Boeshield
®
T-9:
• Table
• Fence faces
• Miter slot
For every 5 hours of use, clean and oil:
• Spindle columns and cartridges
• Offset adjustment mechanisms on fence
• All worm drive and other gears
Once a year, replace the V-belt.
-26- G9933 Three Spindle Shaper
G9933 Three Spindle Shaper -27-
SECTION 8: CLOSURE
The following pages contain general machine
data, parts diagrams/lists, troubleshooting guide
and Warranty/Return information for your Model
G9933 Shaper.
If you need parts or help in assembling your
machine, or if you need operational information,
we encourage you to call our Service
Department. Our trained service technicians will
be glad to help you.
If you have comments dealing specifically with
this manual, please write to our Bellingham,
Washington location using the address in the
General Information section. The specifications,
drawings, and photographs illustrated in this
manual represent the Model G9933 as supplied
when the manual was prepared. However, due to
Grizzly’s policy of continuous improvement,
changes may be made at any time with no obligation on the part of Grizzly. Whenever possible,
though, we send manual updates to all owners of
a particular tool or machine. Should you receive
one, add the new information to this manual and
keep it for reference.
We have included some important safety measures that are essential to this machine’s operation. While most safety measures are generally
universal, Grizzly reminds you that each workshop is different and safety rules should be considered as they apply to your specific situation.
We recommend you keep a copy of our current
catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Service
Department listed in the Introduction section.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines and your local
library are good places to start.
Like all power tools, there is danger associated with the Model G9933 Shaper. Accidents
are frequently caused by lack of familiarity or
failure to pay attention. Use this tool with
respect and caution to lessen the possibility
of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.
The Model G9933 was specifically designed
for wood shaping operations only. DO NOT
MODIFY AND/OR USE THIS MACHINE FOR
ANY OTHER PURPOSE. Modifications or
improper use of this tool will void the warranty. If you are confused about any aspect
of this machine, DO NOT use it until all your
questions have been answered, or serious
personal injury may occur.
Operating this equipment has the potential
for flying debris to cause eye injury. Always
wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain
the safety glasses you wear meet the appropriate standards of the American National
Standards Institute (ANSI).
-28- G9933 Three Spindle Shaper
Design Type...................................................................................................... Floor Model
Overall Dimensions:
Working Table Size (each side) ..............................................................21
3
⁄4
" x 28
1
⁄4
"
Height (includes fence) ............................................................................................45"
Height From Table To Floor ....................................................................................35"
Overall Length ......................................................................................................45
1
⁄
2"
Overall Width ........................................................................................................52
1
⁄8"
Weight (Shipping)............................................................................................1270 lbs.
Weight (in place) ............................................................................................1185 lbs.
Box Size................................................................................55" L x 48
1
⁄4" W x 431⁄2" H
Footprint................................................................37
1
⁄4" max width x 341⁄4" max depth
Capacities:
Spindle Sizes ..........................................................................................................1
1
⁄4"
Spindle Travel ............................................................................................................4"
Exposed Spindle Length ............................................................................................4"
Spindle Openings..............................................................................3
1
⁄4", 61⁄4" and 81⁄4"
Table Counter-bore................................................................8
1
⁄
4" Diameter x
3
⁄
8" Deep
Max. Cutter Diameter ..............................................................................................7
3
⁄4"
Spindle Speeds ........................................................................7,000 & 10,000 R.P.M.
Spindle Bearings..................................................Shielded & Lubricated Ball Bearings
Construction:
Table ....................................................................................Surface Ground Cast Iron
Fence Assembly..............................................................................................Cast Iron
Body Assembly ..............................................................................................Cast Iron
Base....................................................................................................Pre-formed Steel
Motor:
Type ............................................................................TEFC Capacitor-Start Induction
Horsepower..........................................................................................................3 H.P.
Phase ⁄ Voltage ............................................................................Single Phase ⁄ 220 V
Amps..........................................................................................................................18
Cycle ⁄ R.P.M.............................................................................60 Hertz ⁄ 3450 R.P.M.
Bearings..............................................................Shielded & Lubricated Ball Bearings
Switch ..........................................................Magnetic w/ Thermal Overload Protector
Features:
.........................................................................................................3 Separate Motors
............................................................................................3 Micro Adjustable Fences
.....................................................................................3 Magnetic Reversing Switches
...............................................................................Spindles Include Spacers and Nuts
.....................................................................................................Vertical Spindle Lock
.....................................................................................................Spindle Turning Lock
...................................................................................................................Miter Gauge
....................................................................Includes Service Wrenches and Tool Box
Specifications, while deemed accurate, are not guaranteed.
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
GRIZZLY MODEL G9933 THREE SPINDLE SHAPER
MACHINE DATA
SHEET
G9933 Three Spindle Shaper -29-
-30- G9933 Three Spindle Shaper
G9933 Three Spindle Shaper -31-
-32- G9933 Three Spindle Shaper
42 G9933042 HEX BOLT M6 X 35
43 G9933043 SNAP RING C27.5
44 G9933044 BALL BEARING
45 G9933045 SPACER
46 PW02M FLAT WASHER M5
47 PSB10M CAP SCREW M5 X 16
48 PB03M HEX BOLT M8 X 16
49 PW04M FLAT WASHER M10
50 G9933050 THRUST WASHER
51 G9933051 WORM GEAR
52 G9933052 SPACER
53 G9933053 SCREW SHAFT
56 PW01M FLAT WASHER M8
57 PLW04M LOCK WASHER M8
58 PB20M HEX BOLT M8 X 35
59 G9933059 LOCK PIN
60 PRP24M ROLL PIN M5 X 16
61 G9933061 SPRING
62 G9933062 SUPPORT
63 PSB28M CAP SCREW M6 X 15
64 G9933064 KNOB
65 PB09M HEX BOLT M8 X 20
66 PW04M FLAT WASHER M10
67 G9933067 SHAFT
68 G9933068 MOTOR SUPPORT
69 PB20M HEX BOLT M8 X 35
70 PLW04M LOCK WASHER M8
71 PW01M FLAT WASHER M8
72 PN03M HEX NUT M8
73 PB07M HEX BOLT M8 X 25
74 PLW04M LOCK WASHER M8
75 PW04M FLAT WASHER M10
76 G9933076 ADJUSTABLE KEY
77 G9933077 HANDLE
78 G9933078 MOTOR 3 H.P./1-PHASE
79 G9933079 PULLEY
80 PW01M WASHER M8
81 G993381 V-BELT 3V-280 (PVM28)
101 G9933101 FRAME
102 G9933102 DOOR
104 G9933104 DOOR
1 G9933001 OUTSIDE TUBE
2 G9933002 GREASE HOLE
3 PB01M HEX BOLT M10 X 30
4 PLW06M LOCK WASHER M10
5 PW04M FLAT WASHER M10
6 P6007 BALL BEARING 6007ZZ
7 G9933007 SPACER
8 G9933008 SPACER
9 G9933009 INT RETAINING RING 61
10 G9933010 COVER
11 G9933011 CONNECT NUT
12 G9933012 CUTTER SPINDLE
13 G9933013 ROUTER SPINDLE
14 G9933014 ROUTER COLLET
15 G9933015 ROUTER COLLET NUT
16 G9933016 SPACER KIT
17 G9933017 SPINDLE NUT
18 PW06M FLAT WASHER M12
19 PB25M HEX BOLT M12 X 25
20 G9933020 INSIDE TUBE
21 G9933021 SPINDLE
22 G9933022 KEY 7 X 7 X 30
23 P6007 BALL BEARING 6007ZZ
24 G9933024 INT RETAINING RING 61
25 G9933025 SPINDLE PULLEY
26 PW01M FLAT WASHER M8
27 PB09M HEX BOLT M8 X 20
28 G9933028 KNOB
29 G9933029 HANDLE
30 G9933030 ADJUSTMENT WHEEL
31 G9933031 SUPPORT
32 PW01M FLAT WASHER M8
33 PLW04M LOCK WASHER M8
34 G9933034 CAP SCREW M8 X 15
35 G9933035 PLASTIC SPACER
36 PK20M KEY 5 X 5 X 15
37 G9933037 SPACER
38 G9933038 WORM SHAFT
39 G9933039 WORM BOX
40 PW03M FLAT WASHER M6
41 PLW04M LOCK WASHER M8
REF PART # DESCRIPTION REF PART # DESCRIPTION
G9933 Three Spindle Shaper -33-
106 PN09M HEX NUT M12
107 PW06M FLAT WASHER M12
108 G9933108 STUD M12 X 70
109 PSB14M CAP SCREW M8 X 20
110 G9933110 FENCE
111 G9933111 RAIL
112 G9933112 FENCE MOUNT
113 PB07M HEX BOLT M8 X 25
114 PW01M FLAT WASHER M8
115 G9933115 MAIN FENCE HOUSING
116 G9933116 SHAFT
117 PB09M HEX BOLT M8 X 20
118 G9933118 SUPPORT
119 G9933119 SPRING
120 G9933120 KNOB
121 PSS03M SET SCREW M6 X 8
122 G9933122 TABLE INSERT
123 PW04M FLAT WASHER M10
124 PB32M HEX BOLT M10 X 25
125 PEC03M E-RING 10MM
126 G9933126 STOP RING
128 G9933128 KNOB
129 G9933129 DUST HOOD
134 G9933134 KNOB
135 PW01M FLAT WASHER M8
136 G9933136 MITER GAUGE BODY
137 G9933137 SLIDE PLATE
138 G9933138 PIN 6 X 10
139 G9933139 COVER
140 G9933140 STUD 10-24 X 64MM
141 PW02M FLAT WASHER M5
142 PB02M HEX BOLT M6 X12
143 PSS31M SET SCREW M5 X 8
144 G9933144 WORKING TABLE
REF PART # DESCRIPTION
145 PR11M E RETAINING RING 25MM
146 G9933146 3/4” CUTTER SPINDLE
147 G9933147 3/4” SPACER KIT
148 G9933148 SPECIAL NUT
149 G9933149 SPECIAL WASHER
150 PLW04 LOCK WASHER
3
⁄
8"
151 PB18 HEX BOLT
3
⁄8"-16 X 1"
152 G9933152 INNER TABLE INSERT
153 G9933153 T-SLOT WASHER
154 PS09 PHLP SCREW
1
⁄4
"-20 X
1
⁄4
"
155 G9933155 ANGLE INDICATOR
156 P9933156 PHLP SCREW 10-24 X
5
⁄16
"
157 G9933157 SPECIAL SLOT HD BOLT
158 PN02 HEX NUT
5
⁄16
"-18
159 PLABEL-8 GRIZZLY NAMEPLATE
160 P9933160 SLFTAP SCREW M3 X 10
161 P9933161 SPRING
162 PEC02M E-CLIP 4MM
163 P9933163 DOOR HINGE PIN
164 P9933164 FORWARD/REVERSE SW
165 P9933165 ON/OFF SWITCH
166 P9933166 HINGE PIN
167 P9933167 HEX SCREW
1
⁄
4"-20 X
3
⁄
8"
168 P9933168 SPECIAL WASHER
169 P9933169 LATCH
170 P9933170 SPECIAL BOLT
171 P9933171 RUBBER WASHER
172 P9933172 TRIM RING
173 P9933173 HANDLE
174 P9933174 STRAIN RELIEF
175 P9933175 RUBBER WASHER
176 PN07 HEX NUT 10/24
177 P9933177 TERMINAL BLOCK
178 P9933178 STRAIN RELIEF
REF PART # DESCRIPTION
-34- G9933 Three Spindle Shaper
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
WARRANTY AND RETURNS
CUT ALONG DOTTED LINE
10. Which benchtop tools do you own? Check all that apply.
___1" x 42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw ___10" - 12" Thickness Planer
___8" - 10" Bandsaw ___Scroll Saw
___Disc/Belt Sander ___Spindle/Belt Sander
___Mini Jointer
___Other__________________________________________________
11. How many of the machines checked above are Grizzly? ____________
12. Which portable/hand held power tools do you own? Check all that apply.
___Belt Sander ___Orbital Sander
___Biscuit Joiner ___Palm Sander
___Circular Saw ___Portable Planer
___Detail Sander ___Saber Saw
___Drill/Driver ___Reciprocating Saw
___Miter Saw ___Router
___Other__________________________________________________
13. What machines/supplies would you like Grizzly Industrial to carry?
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
14. What new accessories would you like Grizzly Industrial to carry?
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
15. What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
16. Do you think your purchase represents good value?
___Yes ___No
17. Would you recommend Grizzly Industrial to a friend?
___Yes ___No
18. Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
___Yes ___No
19. Comments:_______________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
1. How did you learn about us?
___Advertisement ___Friend
___Catalog ___World Wide Web
___Other__________________________________________________
2. Which of the following magazines do you subscribe to.
___American Woodworker ___Practical Homeowner
___Cabinetmaker ___Shop Notes
___Family Handyman ___Today’s Homeowner
___Fine Homebuilding ___WOOD
___Fine Woodworking ___Wooden Boat
___Home Handyman ___Woodshop News
___Journal of Light Construction ___Woodsmith
___Old House Journal ___Woodwork
___Popular Mechanics ___Woodworker
___Popular Science ___Woodworker’s Journal
___Popular Woodworking ___Workbench
___Other__________________________________________________
3. Which of the following woodworking/remodeling shows do you watch?
___Backyard America ___The New Yankee Workshop
___Home Time ___This Old House
___The American Woodworker ___Woodwright’s Shop
___Other__________________________________________________
4. What is your annual household income?
___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +
5. What is your age group?
___20-29 ___50-59
___30-39 ___60-69
___40-49 ___70 +
6. How long have you been a woodworker?
___0 - 2 Years ___8 - 20 Years
___2 - 8 Years ___20+ Years
7. How would you rank your woodworking skills?
___Simple ___Advanced
___Intermediate ___Master Craftsman
8. What stationary woodworking tools do you own? Check all that apply.
___Air Compressor ___Panel Saw
___Band Saw ___Planer
___Drill Press ___Power Feeder
___Drum Sander ___Radial Arm Saw
___Dust Collector ___Shaper
___Horizontal Boring Machine ___Spindle Sander
___Jointer ___Table Saw
___Lathe ___Vacuum Veneer Press
___Mortiser ___Wide Belt Sander
___Other__________________________________________________
9. How many of your woodworking machines are Grizzly? _____________
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL#____________________Serial#__________________________Order#___________________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
WARRANTY CARD
FOLD ALONG DOTTED LINE
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
Place
Stamp
Here
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Name_______________________________
Street_______________________________
City______________State______Zip______
Send a Grizzly Catalog to a friend:
Loading...