Grizzly G5959Z User Manual
HEAVY-DUTY LEFT-TILTING
12" TABLE SAW
MODEL G5959Z
INSTRUCTION MANUAL
COPYRIGHT © FEBRUARY 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#6025 PRINTED IN TAIWAN
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other
masonry products.
• Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter out microscopic particles.
Table Of Contents
SECTION 1: SAFETY ................................................................................................................................2
Safety Instructions For Power Tools....................................................................................................2
Additional Safety Instructions For Table Saws ....................................................................................4
Safety Accessories ..............................................................................................................................5
Common Definitions, Terms and Phrases ..........................................................................................7
SECTION 2: CIRCUIT REQUIREMENTS ..................................................................................................8
220V Single-Phase ..............................................................................................................................8
Grounding ............................................................................................................................................9
Extension Cords ..................................................................................................................................9
Wiring Diagram ....................................................................................................................................9
SECTION 3: INTRODUCTION..................................................................................................................10
Commentary ......................................................................................................................................10
Unpacking ..........................................................................................................................................11
Piece Inventory ..................................................................................................................................11
Clean Up ............................................................................................................................................12
Site Considerations ............................................................................................................................12
SECTION 4: ASSEMBLY ........................................................................................................................13
Beginning Assembly ..........................................................................................................................13
Extension Wings ................................................................................................................................13
Guard Support Shaft ..........................................................................................................................14
Fence Rails ........................................................................................................................................15
Motor Bracket ....................................................................................................................................15
Installing Saw Blade ..........................................................................................................................16
Table Insert ........................................................................................................................................16
Blade Guard/Splitter ..........................................................................................................................17
SECTION 5: ADJUSTMENTS ..................................................................................................................19
Blade Height ......................................................................................................................................19
Blade Tilt ............................................................................................................................................19
Miter Slot to Blade..............................................................................................................................20
Miter Gauge ......................................................................................................................................22
Rip Fence ..........................................................................................................................................22
Blade Alignment ................................................................................................................................24
SECTION 6: OPERATIONS......................................................................................................................25
Pre-Run Check ..................................................................................................................................25
Test Run ............................................................................................................................................25
Blade Selection ..................................................................................................................................26
Crosscutting ......................................................................................................................................27
Dado Operations ................................................................................................................................28
Ripping ..............................................................................................................................................28
Rabbet Operations ............................................................................................................................30
SECTION 7: MAINTENANCE ..................................................................................................................32
General ..............................................................................................................................................32
Table ..................................................................................................................................................32
V-Belt..................................................................................................................................................32
Lubrication..........................................................................................................................................33
SECTION 8: CLOSURE............................................................................................................................34
Machine Data Sheet ..........................................................................................................................35
Wiring Diagram ..................................................................................................................................36
Parts Breakdown................................................................................................................................37
Parts List ............................................................................................................................................42
Troubleshooting Guide ......................................................................................................................44
Push Stick Template ..........................................................................................................................45
Warranty and Returns........................................................................................................................46
Warranty Card....................................................................................................................................47
-2- G5959Z 12" Left-Tilting Table Saw
Safety Instructions For Power Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should be
kept a safe distance from work area.
6. MAKE WORKSHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
7. DO NOT FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
8. USE RIGHT TOOL. Do not force tool or
attachment to do a job for which it was not
designed.
1. KEEP GUARDS IN PLACE and in working
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS ENVIRONMENT. Do not use power tools in
damp or wet locations, or where any flammable or noxious fumes may exist. Keep
work area well lighted.
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the equipment.
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
NOTICE
SECTION 1: SAFETY
G5959Z 12" Left-Tilting Table Saw -3-
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage
rating should be listed on the motor or tool
nameplate. An undersized cord will cause a
drop in line voltage resulting in loss of power
and overheating. Your extension cord must
also contain a ground wire and plug pin.
Always repair or replace extension cords if
they become damaged.
Minimum Gauge for Extension Cords
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and frees both hands to operate tool.
13. DO NOT OVER-REACH. Keep proper foot-
ing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
15. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended accessories. The use of improper
accessories may cause risk of injury.
LENGTH
AMP RATING 25ft 50ft 100ft
0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 12 10
21-30 10 10 No
Safety Instructions For Power Tools
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. On machines with mag-
netic contact starting switches there is a
risk of starting if the machine is bumped or
jarred. Always disconnect from power
source before adjusting or servicing. Make
sure switch is in OFF position before reconnecting.
17. MANY WOODWORKING TOOLS CAN
“KICKBACK” THE WORKPIECE toward
the operator if not handled properly. Know
what conditions can create “kickback” and
know how to avoid them.
18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged should be properly
repaired or replaced.
19. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Do not
leave tool until it comes to a complete stop.
20. NEVER OPERATE A MACHINE WHEN
TIRED, OR UNDER THE INFLUENCE OF
DRUGS OR ALCOHOL. Full mental alert-
ness is required at all times when running
a machine.
21. NEVER ALLOW UNSUPERVISED OR
INEXPERIENCED PERSONNEL TO
OPERATE THE MACHINE. Make sure
any instructions you give in regards to
machine operation are approved, correct,
safe, and clearly understood.
22. IF AT ANY TIME YOU ARE EXPERIENCING DIFFICULTIES performing the intend-
ed operation, stop using the machine!
Then contact our service department or
ask a qualified expert how the operation
should be performed.
-4- G5959Z 12" Left-Tilting Table Saw
Additional Safety Instructions For Table Saws
1. ALWAYS use blade guard, splitter and
anti-kickback fingers on all ''through-sawing'' operations. Through-sawing operations are those when the blade cuts completely through the workpiece as in ripping
or crosscutting.
2. AVOID KICKBACKS. Kickback is a condi-
tion in which a piece of wood is thrown
back towards an operator at a high rate of
speed. If you do not have a complete
understanding of how kickback occurs, or
how to prevent it, DO NOT operate this
table saw.
3. NEVER reach behind or over the blade
with either hand for any reason.
4. ALWAYS use a push-stick for ripping nar-
row stock.
5. NEVER perform any operation using only
your hands to support or guide the workpiece. Always use either the fence or the
miter gauge to position and guide the work.
6. NEVER stand or have any part of your
body in line with the path of the saw blade.
7. USE GREAT CARE WHEN CUTTING
WITH A DADO BLADE. There is a high
degree of risk involved with any dado operation. Slight movement of the stock away
from the fence will cause kickback. Never
make a through cut using a dado blade.
8. MOVE the rip fence out of the way when
crosscutting.
9. NEVER use the miter gauge and rip fence
at the same time.
10. ALWAYS keep the work firmly against the
miter gauge or fence while holding the
work down against the table.
11. NEVER attempt to free a stalled saw blade
without first turning the saw OFF.
12. PROVIDE adequate support to the rear
and sides of the saw table for wide or long
workpieces.
13. AVOID awkward operations and hand
positions where a sudden slip could cause
your hand to move into the blade.
14. ALWAYS LOWER OR REMOVE SAW
BLADE WHEN NOT IN USE.
15. NEVER USE A DAMAGED SAW BLADE
OR ONE THAT HAS BEEN DROPPED.
16. IF AT ANY TIME YOU ARE EXPERIENCING DIFFICULTIES performing the intend-
ed operation, stop using the machine!
Then contact our service department or
ask a qualified expert how the operation
should be performed.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to
your individual working conditions. Use
this and other machinery with caution and
respect. Failure to follow guidelines could
result in serious personal injury, damage to
equipment or poor work results.
G5959Z 12" Left-Tilting Table Saw -5-
Push Sticks
The use of push sticks (shown in Figure 1), par-
ticularly when cutting small or narrow workpieces,
provides a double benefit for saw operators. The
push stick provides added leverage, enabling the
operator to keep the workpiece firmly supported
against the fence and table. At the same time, the
push stick keeps the operator’s hand safely away
from the rotation of the saw blade. See the template at the end of the manual for construction
details, or purchase one from the Grizzly catalog.
Zero Clearance Table Inserts
Ideal for use when ripping thin strips or making
bevel cuts, these prevent tearout and jammed
blades by supporting material close to the blade.
Use the standard table insert as a template when
creating additional inserts from wood or plywood.
Blade slot inserts can be custom cut for specific
blade angles by raising the running blade into an
uncut insert at the angle you desire. Be sure to
make an additional slot for the blade splitter. We
also carry a wide selection of table inserts (shown
in Figure 2) in the Grizzly catalog. Be sure to hold
the insert firmly in place with a piece of wood
when creating slots. Never hold the table insert
with your hand while cutting new slots.
Safety Accessories
Statistics prove that most common accidents among table saw users can be linked to kickback.
Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its
operator. In addition to the danger of the operator or others in the area being struck by the flying stock, the operator’s hands may be forced into the blade during the kickback. The following
can help minimize kickbacks.
1. Use your blade guard and splitter.
2. Never for any reason place your hand behind the blade. Should kickback occur, your hand will
be pulled into the blade.
3. Make sure the splitter and the blade are aligned.
4. Never use the fence as a guide for crosscutting.
5. Always use either the fence or the miter gauge to position and guide the work.
6. Use a pushstick or featherboard to maintain control of your workpiece.
7. Feed cuts through to completion.
8. Stand to the side when ripping.
9. Ensure your fence and miter slot are parallel to the blade.
If you do not clearly understand kickback and how it occurs, do not operate this table saw.
Figure 1. Push Stick.
Figure 2. Zero Clearance Table Inserts.
-6- G5959Z 12" Left-Tilting Table Saw
Push Paddles
Push paddles provide added leverage and support when ripping or crosscutting wide workpieces. See Figure 3. We offer a number of push
paddles in the Grizzly catalog.
Featherboard
Easily made from scrap stock, featherboards
provide an added degree of protection against
kickback. To make a featherboard, cut a 3040° angle at one end of the board and make a
number of end cuts at approximately
1
⁄4" apart
and 2" to 3" deep. We also offer a number of
featherboards in the Grizzly catalog. See
Figure 4.
Figure 3. Push paddles being used to feed a
work piece into the blade.
Figure 4. Featherboards in use during a ripping
operation.
G5959Z 12" Left-Tilting Table Saw -7-
Common Definitions, Terms and Phrases
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. It is important that you read and become familiar with them
before assembling, adjusting or operating this machine. Your safety is VERY important to us at Grizzly!
Arbor: Metal shaft extending from the drive
mechanism. The cutting blade attaches to the
arbor.
Bevel Edge Cut: Tilting the saw arbor and blade
to an angle between 0° and 45° to perform an
angled cutting operation.
Blade Guard: Metal or plastic mechanism that
mounts over the saw blade to prevent accidental contact with the cutting edge.
Crosscut: Table saw operation in which a piece
of wood is cut across the grain.
Crosscut Sled: A jig that supports the work-
piece during crosscutting operations.
Dado Blade: Blade or set of blades that attach
to the arbor and are used for cutting grooves
and rabbets.
Featherboard: Safety device used to keep a
board against the rip fence or table. Allows
operator to keep hands away from the saw
blade.
Kerf: The resulting cut or gap made by a saw
blade.
Kickback: A condition in which the wood is
thrown back towards an operator at a high
rate of speed.
Miter Gauge: A component that controls the
wood stock movement while performing a
crosscut. Allows for variation of angle cuts
such as miter cuts used on a picture frame.
Non-Thru Cut: A sawing operation that requires
the removal of the blade guard and splitter.
Dado and rabbet cuts are considered NonThru Cuts because the blade does not protrude above the top face of the wood stock.
Always remember to reinstall the blade guard
and splitter after performing a non-thru cut.
Parallel: Being an equal distance apart at every
point. i.e. the rip fence face is parallel to the
side face of the saw blade.
Perpendicular: Intersecting and forming right
angles; at right angles to the vertical and horizontal planes. i.e. the blade is perpendicular to
the table surface.
Push Paddle: Safety aid used to push a piece of
wood stock through a cutting operation.
Push Stick: Safety aid used to push a piece of
wood stock through a cutting operation.
Usually used when rip cutting.
Rabbet: Cutting operation that creates an L-
shaped channel along the edge of wood stock.
Rip Cut: A cut made along grain of the wood.
Sacrificial Fence: A piece of wood attached to
the face of the rip fence that is designed to
extend the fence face away from the metal portion of the fence. Used primarily when making
rabbet cuts with a dado blade.
Splitter: Metal plate attached to the back of the
blade guard that maintains the kerf opening in
the wood when performing a cutting operation.
Standard Kerf:
1
⁄8" gap made with a standard
blade.
Straightedge: A tool used to check the flatness,
parallelism, or consistency of a surface(s).
Thin Kerf:
3
⁄32" gap made with a thin kerf blade.
Thru-Sawing: A sawing operation where the
wood stock thickness is completely sawn
through. Proper blade height usually allows
1
⁄4"
of the top of the blade to extend above the
wood stock.
-8- G5959Z 12" Left-Tilting Table Saw
220V Single-Phase
The Model G5959Z has a 5 HP, 3450 RPM motor
which requires a 220V single-phase circuit. The
cord set included does not have a plug, as the
style of plug you require will depend upon the type
of service you currently have or plan to install. The
motor will safely draw about 30 amps at 220V
under load. If you operate the Model G5959Z on
any circuit that is already close to its capacity, it
might blow a fuse or trip a circuit breaker.
However, if an unusual load does not exist, and
power failure still occurs, have the circuit inspected by a qualified electrician.
The Model G5959Z should be fused at 30 amps.
Fusing at amperage ratings higher than 30 amps
will not adequately protect the circuit. Make sure
that existing electrical wires are capable of handling a 30 amp current. If unsure, seek the assistance of a qualified electrician.
Figure 5. 220V Single-Phase.
SECTION 2: CIRCUIT REQUIREMENTS
In preparing to connect the Model G5959Z to your
existing or new circuit, it will be necessary to connect a plug that matches your 220V receptacle. If
you will be installing a new receptacle and plug,
we recommend using a NEMA-style 6L-30 plug
and outlet shown in Figure 5.
Wiring Diagram
G5959Z 12" Left-Tilting Table Saw -9-
We do not recommend the use of extension cords
on 220V equipment. It is much better to arrange
the placement of your equipment and the installed
wiring to eliminate the need for extension cords.
Should it be necessary to use an extension, make
sure the cord is rated Hard Service (grade S) or
better. Refer to the chart in Section 1: Safety to
determine the minimum gauge for the extension
cord. The extension cord must also contain a
ground wire and plug pin. Always repair or replace
extension cords when they become worn or damaged.
Extension Cords
A wiring diagram is provided at the back of this
manual should it be necessary to repair or revise
the wiring. Always utilize a qualified electrician
when doing any electrical work on this equipment.
We have covered some basic electrical
requirements for the safe operation of your
machine. These requirements are not necessarily comprehensive. You must be sure
that your particular electrical configuration
complies with local and state codes.
Ensure compliance by checking with your
local municipality or a licensed electrician.
Grounding
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having
an equipment-grounding conductor which must
be properly connected to a grounding plug. The
plug must be plugged into a matching outlet that
is properly installed and grounded in accordance
with all local codes and ordinances.
Improper connections of the electrical-grounding
conductor can result in risk of electric shock. The
conductor with green or green and yellow striped
insulation is the electrical-grounding conductor. If
repair or replacement of the electric cord or plug
is necessary, do not connect the equipment
grounding conductor to a live terminal.
This equipment must be
grounded. Verify that any
existing electrical outlet
and circuit you intend to
plug into is actually
grounded. Under no circumstances should the
grounding pin from any
three-pronged plug be
removed. Serious injury
may occur.
-10- G5959Z 12" Left-Tilting Table Saw
We are proud to offer the Grizzly Model G5959Z
Left-Tilt 12" Table Saw. The Model G5959Z is
part of a growing Grizzly family of fine woodworking machinery. When used according to the
guidelines set forth in this manual, you can expect
years of trouble-free, enjoyable operation and
proof of Grizzly’s commitment to customer satisfaction.
The Model G5959Z is an industrial grade table
saw intended for professional use. Features
include cast iron trunnions, 4" dust port, triple Vbelt drive, dual arbor (
5
⁄8" and 1"), cam lever fence,
magnetic switch, and a 5 HP, 220V, single-phase
motor.
All running parts operate on shielded ball bearings and require no maintenance for the life of the
bearings. We also offer many accessories for the
table saws including blades, outfeed rollers, a
sliding table and a mobile base. Please refer to
our current catalog for prices and ordering information.
We are also pleased to provide this manual with
the Model G5959Z. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It represents our effort to produce the best documentation possible. If you have any comments regarding this manual, please write to us at the address
below:
Grizzly Industrial, Inc.
C
/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Commentary
Most importantly, we stand behind our machines.
If you have any service questions or parts
requests, please call or write us at the location
listed below:
Grizzly Industrial, Inc.
1203 Lycoming Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G5959Z as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
Whenever possible, though, we send manual
updates to all owners of a particular tool or
machine. Should you receive one, we urge you to
insert the new information with the old and keep it
for reference.
Read the manual before
assembly and operation. Become familiar
with the machine and
it’s operation before
beginning any work.
Serious personal injury
may result if safety or
operational information
is not understood or followed.
SECTION 3: INTRODUCTION
G5959Z 12" Left-Tilting Table Saw -11-
The Model G5959Z is shipped from the manufacturer in a carefully packed carton. If you discover
the machine is damaged after you have signed
for delivery, please call Customer Service immediately at (570) 546-9663.
When you are completely satisfied with the condition of your shipment, you should inventory its
parts.
The G5959Z is a heavy
machine, 635 lbs. shipping weight. DO NOT
over-exert yourself
while unpacking or
moving your machine –
you will need assistance and power equipment. Serious personal
injury may occur if safe
moving methods are
not followed.
Make sure floor structure
is capable of supporting
the combined weight of
the machine, accessories and people.
Some metal parts may
have sharp edges on
them after they are
formed. Please examine
the edges of all metal
parts before handling
them. Failure to do so
could result in injury.
Piece Inventory
After all the parts have been removed from their
containers, you should have:
1. Table Saw Cabinet (Not Shown)
2. Miter Gauge
3. Extension Wings (2)
4. Fence
5. Splitter/Guard Assembly
6. Splitter/Guard Support Shaft
7. Hardware Bag
8. Arbor Spanner Wrench
9. Open End Wrench (2)
10. Hex Wrench Set
11. Arbor Extension Assembly
12. Motor Cover
13. Dado Table Insert
14. Standard Table Insert (Not Shown)
15. Fence Angle Irons (2)
16. Fence Rail
17. Tool Box
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them; or for the sake of expediency, replacements can be obtained at your local
hardware store.
Figure 6. G5959Z component layout.
3
4
5
6
7
8
9
10
17
11
12
2
13
15
15
16
Unpacking
-12- G5959Z 12" Left-Tilting Table Saw
The table and other unpainted parts of the Model
G5959Z are coated with a waxy grease that protects them from corrosion during shipment. Clean
this grease off with a solvent cleaner or citrusbased degreaser such as Grizzly’s G7895
Degreaser. Do not use chlorine-based solvents –
if you happen to splash some onto a painted surface, you will ruin the finish.
Site Considerations
1. Floor Load: Your Model G5959Z weighs
635 lbs. with a 26" x 23
1
⁄2" footprint. Most
commercial floors are suitable for the saw.
Some residential floors may require additional bracing to support both machine and operator.
2. Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through each machine, and
space for auxiliary stands, work table or
other machinery when establishing a location for your table saw.
3. Lighting and Outlets: Lighting should be
bright enough to eliminate shadows and prevent eye strain. Electrical circuits should be
dedicated or large enough to handle amperage requirements. Outlets should be located
near each machine so power or extension
cords are clear of high-traffic areas. Observe
local electrical codes for proper installation
of new lighting, outlets, or circuits.
Make your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. Never
allow visitors in your shop
when assembling, adjusting or operating equipment.
Do not use gasoline or
other petroleum-based
solvents. They have low
flash points which make
them extremely flammable. A risk of explosion
and burning exists if
these products are
used. Serious personal
injury may occur if this
warning is ignored.
Do not smoke while using
solvents. A risk of explosion or fire exists and may
result in serious personal
injury.
Many of the solvents
commonly used to clean
machinery can be toxic
when inhaled or ingested. Always work in wellventilated areas far from
potential ignition sources
when dealing with solvents. Use care when disposing of waste rags and
towels to be sure they do
not create fire or environmental hazards.
Clean Up
G5959Z 12" Left-Tilting Table Saw -13-
Most of your Model G5959Z has been assembled
at the factory, but some parts must be assembled
or installed after delivery. We have organized the
assembly process into steps. Please follow along
in the order presented here.
TOOLS REQUIRED: You will need a high quality
square, a long straightedge, 10mm, 12mm, 14mm
open end wrenches and a 3mm hex wrench.
Extension Wings
Inspect the extension wings for burrs or foreign
material that may inhibit assembly. The mating
edges of the wings and table must be clean,
smooth, and flat. Use a wire brush or file if necessary to clean up the edges.
1. Disconnect the table saw from the power
source.
2. Attach the left wing to the table using three
hex head bolts and flat washers. Adjust the
wing reasonably flush with the table. Do not
tighten the bolts.
3. Attach the right wing to the table using three
hex head bolts and flat washers. Adjust the
wing reasonably flush with the table. Do not
tighten the bolts.
4. Align the top of the wing flush with the table
top directly above the front bolt, and tighten
the front bolt. The front edge of the extension
wing should also be flush with the front edge
of the table.
5. Raise or lower the rear of the extension wing
until the middle of the wing is flush with the
table top. Tighten the middle bolt.
NOTICE
The right and left wings are not the same.
The left wing has two tapped holes on the
outside edge, the right has a tapped hole on
the front and back edge. If the wings are not
installed in their correct location, the fence
cannot be attached.
The wings represent a
very heavy load.
Improper lifting techniques or inadequate lifting assistance could
result in serious injuries.
Disconnect power to the
machine when performing any maintenance,
assembly or adjustments. Failure to do this
may result in serious
personal injury.
Wear safety glasses during the entire assembly
process. Failure to comply may result in serious
personal injury.
Some metal parts may
have sharp edges on
them after they are
formed. Please examine
the edges of all metal
parts before handling
them. Failure to do so
could result in injury.
Beginning Assembly
SECTION 4: ASSEMBLY
!
-14- G5959Z 12" Left-Tilting Table Saw
Figure 7. Using tape to shim for wing alignment.
Masking Tape
6. Raise or lower the rear of the wing until the
wing and table are flush. Tighten the bolt.
Further adjustments should be minimal.
7. Check flushness at the front bolt and adjust
if necessary.
8. Repeat Steps 3-7 for the other extension
wing.
9. Now, check the alignment of the table and
both wings with a straightedge. The straightedge should run flat across both wings and
the table top. If the straightedge contacts
both wings and the table evenly, you are finished with this section. If it does not, continue to Step 10.
10. If the extension wings tilt up or down at the
outside edges, remove the wings and shim
them with masking tape as shown in Figure 7.
a. If the wings tilt down, stick layers of mask-
ing tape under each bolt near the bottom
edge of the wing and retighten.
b. If the wing tilts up, apply layers of masking
tape above each bolt near the top edge of
the wing and retighten. Allow tape to
extend above the table surface and trim
with a sharp knife after final assembly.
11. Replace the wings and check again.
FIGURE 8. Attaching guard support shaft.
Guard Support Shaft
1. Disconnect the table saw from the power
source.
2. Push the threaded end of the shaft through
the hole in the back of the sawand into the
rear trunnion bracket (Figure 8).
3. Reach into the table opening and secure the
guard support shaft with the hex nut and
washer.
4. Slide the guard support over the shaft and
tighten the hex bolt.
Loading...