Gripe Rite GRTPIN23 Operator's Manual

1

OPERATOR’S MANUAL

AND PARTS LIST

MODEL GRTPIN23 PIN NAILER

Distributed By

www.grip-rite.com

32

TABLE OF CONTENTS

TABLE OF CONTENTS -------------------------------- 2

SPECIFICATIONS --------------------------------------- 3

SAFETY ---------------------------------------------------- 4

TOOL PARTS --------------------------------------------- 8

PARTS DESCRIPTION--------------------------------- 9

OPERATION--------------------------------------------- 10

PARTS SCHEMATIC---------------------------------- 12

PARTS LIST --------------------------------------------- 13

MAINTENANCE ---------------------------------------- 14

TROUBLESHOOTING ------------------------------- 15

WARRANTY --------------------------------------------- 18

SPECIFICATIONS

IMPORTANT SAFETY INFORMATION

You must read this entire manual and familiarize yourself with all
safety, operating, and service instructions before loading, handling,
or using your tool. When used correctly, pneumatic fastening tools
provide a lightweight, powerful, and safe means of fastening. Used
improperly, these tools can cause serious injury to you and those
around you.

For best results, use only Grip-Rite™ collated fasteners.

FASTENER SELECTION CHART

SIZE QTY SKU

1/2 x 23 Ga. (12 mm) 3M GR12PIN

5/8 x 23 Ga. (16 mm) 3M GR58PIN

3/4 x 23 Ga. (19 mm) 3M GR34PIN

1” x 23 Ga. (25 mm) 3M GR1PIN

1-3/16” x 23 Ga. (30 mm) 3M GR1316PIN

ASSORTED x 23 Ga. 3M GRMIXPIN

SPECIFICATIONS

MODEL GRTPIN23
FASTENER RANGE 1/2” - 1-3/16 ” (12 mm - 30 mm)

FASTENER TYPE 23 Ga. Headless Pin

FASTENER ANGLE Straight

MAGAZINE CAPACITY 140 Pins

MAX AIR PRESSURE 100 psi (6.9 bar)

MIN AIR PRESSURE 70 psi (4.9 bar)

TOOL WEIGHT 2.15 lbs. (.98 kg)

TOOL LENGTH 8.75” (222.3 mm)

TOOL HEIGHT 6.69” (170 mm)

TOOL WIDTH 1.81” (56 mm)

TRIGGER TYPE Non-restrictive

AIR CONNECTION Male Quick Connect Coupler
LUBRICATION 10W Air Tool Oil (Provided)

NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 3774, ISO 11201:

A-weighted single-event sound
pressure level at operator’s position ---------------------------------- LpA, 1s = 86 dBA

A-weighted single-event sound power level ----------------------- LwA, 1s = 93 dBA
A-weighted single-event surface sound

pressure level ---------------------------------------------------------------- LpA, 1s = 80 dBA

VIBRATION CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 8862-1

Weighted root mean square acceleration ---------------------------- = 1.2 m/s

2

54

SAFETY

SAFETY LABELS

This pneumatic fastening tool includes a warning label to help remind you of
important safety information when operating the tool. The safety label must be
legible at all times, and must be replaced if it becomes worn or damaged.

SYMBOL

DESCRIPTION

READ THE MANUAL - The manual contains

important safety and operating instructions
that must be followed. All tool users must
read the manual before using the tool.

WEAR SAFETY GLASSES - Tool operator
and bystanders must wear safety glasses
with side shield that meet ANSI Z87.1
requirements.

RISK OF PERSONAL INJURY - Failure to
follow all safety and operating instructions,
or misuse of the tool, can result in serious
injury to tool operator and bystanders.

SAFETY SYMBOLS

These safety symbols provide a visual reminder of basic safety
rules, and the personal injury hazard that may arise if all safety and
operating instructions are not followed. Make sure you understand
the meaning of each of these symbols, and protect yourself and
others by obeying all safety and operating instructions.

SAFETY

SAFETY INSTRUCTIONS

WEAR SAFETY GLASSES

Always wear safety glasses with side shields that meet ANSI
Z87.1 requirements when operating the tool. Make sure all
others in work area wear safety glasses.

WEAR HEARING PROTECTION

Wear hearing protection to protect your hearing from noise.
Prolonged exposure to loud noise can result in hearing loss.

NEVER OPERATE THE TOOL WITH OXYGEN OR OTHER
BOTTLED GASES

Oxygen and other reactive or high-pressure bottled gases
can cause the tool to explode. Use clean, dry regulated
compressed air from a properly operating air compressor.

DO NOT EXCEED MAXIMUM RECOMMENDED OPERATING AIR
PRESSURE OF 100 PSI /6.9 Bar.

Exceeding the maximum recommended air pressure can
cause the tool housing to burst, or cause premature failure of
components.

NEVER CONNECT THE TOOL TO AN AIR SUPPLY THAT HAS
THE POTENTIAL TO EXCEED 180 PSI/12.4 Bar.

Using a regulated air supply with a line or tank pressure
greater than 180 psi can cause the tool to burst if the air line
regulator fails suddenly.

USE AN AIR HOSE RATED FOR 180 PSI/12.4 Bar OR
GREATER

Always use air hose rated to handle 180 psi or the maximum
potential pressure of the air supply.

ALWAYS KEEP THE TRIGGER SAFETY LEVER IN THE FOR­WARD “SAFE” POSITION UNTIL TOOL IS IN DRIVING POSI­TION AND YOU ARE READY TO DRIVE A FASTENER.

When driving is completed, or before reloading, move the
trigger safety lever forward to “SAFE” position.

DO NOT ATTEMPT TO OPERATE THE TOOL IF THE TOOL’S
OPERATING CONTROLS HAVE BEEN MODIFIED OR ARE NOT
WORKING PROPERLY.

Attempting to use a tool with modified or malfunctioning
trigger or safety lever can result in a fastener being driven
unintentionally.

100 psi

4.9 bar

70 psi

6.9 bar

76

SAFETY

USE CORRECT FASTENERS

Only use the correct fastener for the tool. Using fasteners
with incorrect specifications can jam the tool or cause
serious injuries.

USE THE CORRECT FASTENERS FOR THE APPLICATION.

Using the wrong fasteners can cause the workpiece to split
and allow the fastener to fly free.

KEEP TOOL POINTED IN A SAFE DIRECTION WHEN LOADING
FASTENERS.

Never point the tool at yourself or anyone else when loading
fasteners.

DO NOT LOAD TOOL WITH TRIGGER DEPRESSED.

Depressing the trigger during loading can result in an
unintentional fastener drive.

KEEP FINGER OFF TRIGGER UNTIL TOOL IS IN POSITION TO
DRIVE A FASTENER.

An unexpected bump or sudden contact with your body or that
of a bystander can result in serious injuries.

AVOID DRIVING FASTENERS INTO KNOTS, ON TOP OF
OTHER FASTENERS, AT WORKPIECE EDGES, OR INTO
BRITTLE MATERIALS.

Driving fasteners into extremely hard materials, or driving into
workpiece edges, can cause fasteners to deflect away from
the workpiece. Flying fasteners can cause serious injuries.

DO NOT MODIFY TOOL

Modifications can cause a tool to be unsafe and can cause
the tool to operate improperly.

ONLY USE A RELIEVING-TYPE AIR COUPLING IN THE TOOL
AIR INLET OPENING.

Use of a non-relieving air coupling on the tool can trap air
inside the tool housing, and allow the tool to drive a fastener
even after the air hose has been disconnected.

SAFETY INSTRUCTIONS

SAFETY

KEEP HANDS AND BODY PARTS AWAY FROM AREA BEING
FASTENED.

Fasteners can deflect and turn as they are being driven into
the workpiece, and penetrate fingers, hands, and other body
parts that may be in the fastening area.

DO NOT OVERREACH OR WORK WHILE ON UNSTABLE
FOOTING

If you lose your balance while fastening, you could drive a
fastener into yourself or a bystander.

DO NOT USE TOOL IF TOOL MALFUNCTIONS OR BEGINS
LEAKING AIR.

Operating a malfunctioning tool can result in an unexpected
fastener discharge and injury to yourself or others.

DISCONNECT THE TOOL FROM THE AIR SUPPLY TO RE­LOAD, CLEAR JAMS, OR PERFORM MAINTENANCE.

Never attempt to reload a tool, clear a jam, or perform
maintenance without first disconnecting the air supply.

NEVER LEAVE A LOADED, PRESSURIZED TOOL
UNATTENDED

A loaded, pressurized tool could be picked up or handled by
someone who is unfamiliar with the tool or that has not read
the tool manual.

KEEP TOOLS OUT OF THE REACH OF CHILDREN

Place the tool back in the tool box after use, and store the tool
out of reach.

SAFETY INSTRUCTIONS