Grieve Corporation 1762-IA8 Installation Manual

Installation Instructions

MicroLogix™ 1762-IA8 120V ac Input Module

Inside

Description.......................................................3

Installation........................................................4

Mounting..........................................................5

System Assembly .............................................7

Field Wiring Connections...................................7

I/O Memory Ma pping......................................10

Specifications.................................................11

Hazardous Location Considerations ................13

Environnements dang ereux.............................14

1762-IN002A-US-P

2 MicroLogix™ 1762-IA8 120V ac Input Module

For More Information

For Refer to this Document Pub. No.

Information on installing, wiring, and operating a MicroLogix 1200 Programmable Controller

Installation guide for the MicroLogix 1200 Programmable Controller.

Installation guide for the MicroLogix 1200 Memory Module and Real Time Clock.

Installation guide for the 1762-OW8 Discrete Output Module

Installation guide for the 1762-IQ8 Discrete Input Module

Installation guide for the 1762-IF2OF2 Analog I/O Module

More information on proper wiring and grounding techniques.

If you would like a manual, you can:

MicroLogix 1200 Programmable Controllers User Manual

MicroLogix 1200 Programmable Controllers Inst al lation Instructions

MicroLogix 1200 Memory Module and/or Real Time Clock Installation Instructions

1762-OW8 Relay Outpu t Module Installation Instructions

1762-IQ8 DC Input Module Installation Instructions

1762-IF2OF2 Analog Input/ Outp ut Module Installation Inst ructions

Industrial Automation Wirin g and Grounding Guidelines

1762-UM001A-US-P

1762-IN006A-ML-P

1762-IN001A-US-P

1762-IN003A-US-P

1762-IN004A-US-P

1762-IN005A-US-P

1770-4.1

• downlo ad a fre e el ec tr o n ic ver s i on fro m the inter n et :

www.ab .c om /micrologix

www.theautomationbookstore.com

• purchase a printed manual by:

– conta cting your local distributor or Rockwell Automation representative – visiting – calling

1762-IN002A-US-P

1.800.963.9548

001.330.725.1574

www.theautomationbookstore.com

(USA/Canada)

(Outside USA/Canada)

and placing your order

MicroLogix™ 1762-IA8 120V ac Input Module 3

Description

Item Description

1a upper panel mounting tab 1b lower panel mounting tab 2 I/O diagno stic LEDs 3 module door with terminal

identification label

4 bus connecto r

with male pins

5 bus connector cover 6 flat ribbon c able with bus

connector (female pins)

7 terminal block 8 DIN rail latch 9 pull loop

1762-IN002A-US-P

4 MicroLogix™ 1762-IA8 120V ac Input Module

Installation

1762 I/O is suitable for use in an industrial environment whe n installed in accord an ce with thes e in struction s . Sp e ci fic ally, this equipm en t is in tended for

use in clean, dry environmen ts (Pollution degree 2 exceeding Over Vo ltage Category II

(2)

(IEC 60664-1).

Prevent Electrostatic Discharge

(1)

) and to circuits not

(3)

Remove Power

ATTENTION:

circuits or semiconductors if you touch bus connector pins. Follow these guidelines when you handle the module:

• Touch a grounded object to discharge static potential.

• Wear an approved wrist-strap grounding de vice.

• Do not touch the bus connector or connector pins.

• Do not touch circuit components insid e the module.

• If av ailable, use a static-safe work s tation.

• When not in use, keep the module in its static-shield box.

ATTENTION:

this module. When you remov e or install a module with power applied, an electrical arc may occur. An electrical arc can cause personal injury or property damage by:

• sending an erroneous signal to your system’s field devices ,

causing unintended machine motion

• causing an explosion in a hazardous environment

• causing permanent damage to the module’s circuitry

Electrical arcing causes excessive wear to contacts on both the module and its mati ng connector. Worn contacts may create electri cal resistan c e.

Electrostati c discharge can damage integrated

Remove po wer before removing or installing

(1)

Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a temporary conductivity caused by condensation shall be expected.

(2)

Over Voltage C ateg ory II i s the l oad leve l se ction of t he elec tri c al dist ribution system. A t this lev el tr ans ient voltages are controlled and do not exceed the impulse voltage capability of the product’s insulation.

(3)

Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.

1762-IN002A-US-P

MicroLogix™ 1762-IA8 120V ac Input Module 5

Mounting

ATTENTION:

the module and a ll other e qui pment near t he module is mounte d a nd

wiring is complete. Once wiring is complete and the module is free of debris, carefully remove protective debris strip. Failure to remove strip before operating can cause overheating.

Minimum Spacing

Main ta in s p acing from enclosure walls, wireways, adjacent equipment, et c. Allow

50.8 mm (2 in.) of space on all side s for ad eq u at e ventilation, as sho wn:

Note:

1762 expansion I/O ma y be mounted horizontally only.

ATTENTION:

be sure that all debris (metal chips, wire strands, etc.) is kept from

falling into the module. Debris that falls into the module could cause damage when power is applied to the module.

Do not remove protective debris strip until after

Top

Side Side

During panel or DIN rail mounting of all device s,

MicroLogix

1200

1762 I/O

Bottom

1762 I/O

1762-IN002A-US-P

+ 11 hidden pages