GreenWorks 5100744 Operator's Manual
Read all safety rules and instructions carefully before operating this tool.
OPERATOR’S MANUAL
TOLL-FREE HELPLINE: 1-888-909-6757
www.GreenWorksTools.com
1600 PSI / 1.3 GPM
ELECTRIC PRESSURE WASHER
5100744
2
Introduction.......................................................................................................................... 3
Important Safety Instructions............................................................................................ 3 - 4
Specific Safety Rules........................................................................................................5 - 6
Symbols ............................................................................................................................ 7- 8
Electrical ......................................................................................................................... 9-10
Know Your Pressure Washer ..............................................................................................11
Assembly .......................................................................................................................12-16
Operation. ..................................................................................................................... 17-20
Maintenance ................................................................................................................. 21-23
Troubleshooting ............................................................................................................ 24 -26
Warranty ............................................................................................................................ 27
Exploded View ................................................................................................................... 2 8
Part List ........................................................................................................................ 2 9 - 30
PRODUCT SPECIFICATIONS
Universal Motor ..................................................................................... 120 V, 60 Hz, 13 Amps
Max. Pounds Per Square Inch Pressure* ..................................................................... 1600 psi
Rated Gallons Per Minute*........................................................................................... 1.3 gpm
Maximum Inlet Water Temperature .................................................................................. 104˚F
Unit Weight .................................................................................................... 15.83lbs (7.18kg)
TABLE OF CONTENTS
1950 C.U
3
W A R N I N G
Read and understand all instructions. Failure to follow all instructions listed below may result
.
W A R N I N G
When using this product basic precautions should always be followed, including the following
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
• To reduce the risk of injury, close supervision is necessary when a product is used near
children.
• Be thoroughly familiar with controls. Know how to stop the product and release pressure
quickly.
• Stay alert and exercise control. Watch what you are doing and use common sense. Do not
operate product when you are tired. Do not rush.
•
medication.
• Keep the area of operation clear of all people,particularly small children, and pets.
• Don’t overreach or stand on unstable support. Keep proper footing and balance at all times.
•
• This product is provided with a ground fault circuit interrupter built into the power cord
plug. If replacement of the plug or cord is needed, use only identical replacement parts.
W A R N I N G
Risk of injection or injury – Do not direct discharge stream at people or animals.
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
This pressure washer is provided with a ground fault circuit interrupter (GFCI) built into the plug
of the power supply cord. This device provides additional protection from the risk of electric
shock. Should replacement of the plug or cord become necessary, use only identical replacement
parts that include GFCI protection.
SERVICING OF A DOUBLE-INSULATED APPLIANCE
In a double-insulated product, two systems of insulation are provided instead of grounding.No
grounding means is provided on a double-insulated product, nor should a means for grounding
be added to the product. Servicing a doubleinsulated product requires extreme care and
parts for a double insulated product must be identical to the parts they replace. A doubleinsulated
product is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED.”The
symbol may also be marked on the product.
IMPORTANT SAFETY INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
EXTENSION CORDS
by a marking “Acceptable for use with outdoor appliances; store indoors while not in use.” Use
only extension cords having an electrical rating not less than the rating of the product. Do not use
damaged extension cords. Examine extension cord before using and replace if damaged. Do not
abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and
sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the
product from the extension cord.
W A R N I N G
To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch
plug with wet hands.
DO NOT USE WITH EXTENSION CORD, USE DIRECT INTO RECEPTACLE.
5
SPECIFIC SAFETY RULES
• Know your product. Read the operator’s manual care-fully. Learn the machine’s applications
and limitations as well as the specic potential hazards related to this product.
• To reduce the risk of injury, keep children and visitors away. All visitors should wear safety
glasses and be kept a safe distance from work area.
• Use right product. Don’t force product or attachment to do a job it was not designed for. Don’t
use it for a purpose not intended.
• Dress properly. Do not wear loose clothing, gloves, neckties, or jewelry. They can get caught
and draw you into moving parts. Rubber gloves and nonskid footwear are recommended when
working outdoors. Also wear protective hair covering to contain long hair.
• Do not operate the equipment while barefoot or when wearing sandals or similar
lightweight footwear. Wear protective footwear that will protect your feet and improve your
footing on slippery surfaces.
• Exercise caution to avoid slipping or falling.
• Always wear eye protection with side shields marked to comply with ANSI Z87.1.
Following this rule will reduce the risk of serious personal injury.
• Use only recommended accessories. The use of improper accessories may cause risk of
injury.
• Check damaged parts. Before further use of the product, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its operation. A guard or other part that is
damaged must be properly repaired or replaced by an authorized service center to avoid risk of
personal injury.
• Never leave product running unattended. Turn power off. Don’t leave product until it comes
to a complete stop.
• Keep the motor free of grass, leaves, or grease to reduce the chance of a re hazard.
• Follow manufacturer’s recommendations for safe loading, unloading, transport, and
storage of machine.
• Keep product dry, clean, and free from oil and grease. Always use a clean cloth when
cleaning. Never use brake uids, gasoline, petroleum-based products, or any solvents to clean
product.
• Check the work area before each use. Remove all objects such as rocks, broken glass, nails,
wire, or string which can be thrown or become entangled in the machine.
• Do not use product if switch does not turn it off. Have defective switches replaced by an
authorized service center.
• Avoid dangerous environment. Don’t expose to rain. Keep work area well lit.
• Do not abuse the cord. Never use the cord to carry the product or to disconnect the plug from
an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged
cords immediately. Damaged cords increase the risk of electric shock.
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or
outlet(s) to be used for the product. Receptacles are available having built-in GFCI protection
and may be used for this measure of safety.
• To reduce the risk of electric shock, this product has a polarized plug (one blade is
wider than the other) and will require the use of a polarized extension cord. The plug will
t into a polarized extension cord only one way. If the plug does not t fully into the extension
cord, reverse the plug. If the plug still does not t, obtain a correct polarized extension cord. A
polarized extension cord will require the use of a polarized wall outlet. This plug will t into the
polarized wall outlet only one way. If the plug does not t fully into the wall outlet, reverse the
6
SPECIFIC SAFETY RULES
plug. If the plug still does not t, contact a qualied electrician to install the proper wall outlet.
Do not change the equipment plug, extension cord receptacle, or extension cord plug in any
way.
• Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.)
of at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating.
• Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and
free from oil or grease.
• Never direct a water stream toward people or pets, or any electrical device.
• Before starting any cleaning operation, close doors and windows. Clear the area to be
cleaned of debris, toys, outdoor furniture, or other objects that could create a hazard.
• Do not use acids, alkalines, solvents, ammable material, bleaches, or industrial grade
solutions in this product. These products can cause physical injuries to the operator and
irreversible damage to the machine.
WARNING
High pressure jets can be dangerous if subject to misuse. The jet must not be directed at
people, animals, electrical devices, or the machine itself.
• Keep the motor away from ammables and other hazardous materials.
• Check bolts and nuts for looseness before each use. A loose bolt or nut may cause serious
motor problems.
• Before storing, allow the motor to cool.
• When servicing use only identical replacement parts. Use of any other parts may create a
hazard or cause product damage.
• ONLY use cold water.
• Make sure minimum clearance of 3 feet is maintained from combustible materials.
• Connect pressure washer only to an individual branch circuit.
• Hold the handle and wand securely with both hands. Expect the trigger handle to move
when the trigger is pulled due to reaction forces. Failure to do so could cause loss of control
and injury to yourself and others.
• Save these instructions. Refer to them frequently and use them to instruct other users. If you
loan someone this product, loan them these instructions also.
WARNING
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically-treated lumber Your risk from these exposures varies,
depending on how often you do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to lter out microscopic particles
SAVE THESE INSTRUCTIONS
7
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amps Current
Hz Hertz Frequency (cycles per second)
W Watt Power
no No Load Speed Rotational speed, at no load
Alternating Current Type of current
.../min Per Minute Revolutions, strokes, surface speed, orbits etc.,
per minute
Class II Construction Double-insulated construction
Safety Alert Indicates a potential personal injury hazard.
To reduce the risk of injury, user must read and
Read Operator’s Manual understand operator’s manual before using this
product.
Eye Protection Always wear eye protection with side shields
marked to comply with ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations.
To reduce the risk of injection or injury, never
direct a water stream towards people or pets or
Risk of Injection place any body part in the stream. Leaking
Kickback To reduce the risk of injury from kickback, hold
the spray wand securely with both hands when
the machine is on.
Electric Shock Failure to use in dry conditions and to observe
safe practices can result in electric shock.
Some of the following symbols may be used o n this product. Please study them and learn their
meaning. Proper inter-pretation of these symbols will allow you to operate the product better and safer.
SYMBOLS
8
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper inter-pretation of these symbols will allow you to operate the product better and safer.
SERVICE
service technician. For service we suggest you return the product to your nearest AUTHORIZED
SERVICE CENTER for repair. When servicing, use only identical replacement parts.
W A R N I N G
To avoid serious personal injury, do not attempt to use this product until you read thoroughly
and understand completely the operator’s manual. If you do not understand the warnings and
instructions in the operator’s manual , do not use this product . Call HGTV HOME customer
service for assistance.
W A R N I N G
The operation of any power tool can result in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields and, when needed, a
full face shield. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields. Always use eye protection which is marked to
comply with ANSI Z87.1.
SYMBOL NAME DESIGNATION/EXPLANATION
To reduce the risk of injury or damage, DO NOT
USE ACIDS, ALKALINES,BLEACHES,
Chemical Burns SOLVENTS, FLAMMABLE MATERIAL, OR
INDUSTRIAL GRADE SOLUTIONS in this
product.
SYMBOL SIGNAL MEANING
DANGER Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.
CAUTION (Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
9
ELECTRICAL
NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and
your nearest authorized service center for repair. Always use original factory replacement parts when servic-
ing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be connected to a power supply that
is 120 volts, 60 Hz, AC only (normal household current). Do not operate this product on direct
current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,double-check the power supply.
EXTENSION CORDS (
See Figure 1.)
When using a power tool at a considerable distance from a power source, be sure to use an
extension cord that has the capacity to handle the current the product will draw. An undersized
cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to
determine the minimum wire size required in an extension cord. Only round jacketed cords listed
by Underwriter’s Laboratories (UL) should be used. When working outdoors with a product, use
an extension cord that is designed for outside use.This type of cord is designated with “WA” or “W”
on the cord’s jacket. Before using any extension cord, inspect it for loose or exposed wires and
cut or worn insulation. It is possible to tie the extension cord and power cord in a knot to prevent
the plug end of the power cord into the receptacle end of the extension cord. This method can
also be used to tie two extension cords together..
W A R N I N G
The double insulated system is intended to protect the user from shock resulting from a break in
the product’s internal insulation. Observe all normal safety precautions to avoid electrical shock.
DOUBLE INSULATED
Double insulation is a concept in safety in electric power tools, which eliminates the need for the
usual three-wire grounded power cord. All exposed metal parts are isolated from the internal
metal motor components with protecting insulation. Double insulated products do not need to be
grounded.
Fig. 1
Pressure washer power cord
Extension cord
Drip loop
Loading...