Greenwood SK200A, SK200B2, SK200MA, SK200T Installation Instructions Manual

SK200A for Continuous Applications
SK200B2, MA & T Centrifugal Fans
for Kitchens & Utility Rooms

Greenwood Air Management Ltd

Greenwood House

Brookside Avenue

Rustington, West Sussex BN16 3LF

Tel: [phone] Fax: [phone]

Email: [e-mail]

Internet: www.greenwood.co.uk

Environmental

Slotvent

Installation Instructions

SK200 install AW 3.6.10 4/6/10 01:58 Page 1

32

Read all instructions before
commencing installations

WARNING NOTES:

● The appliance is not intended for use by young
children or infirm persons unless they have been
adequately supervised by a responsible person to
ensure that they can use the appliance safely.
Young children should be supervised to ensure
that they do not play with the appliance.

● Siting Notes: Where an open-flued oil or gas-
fuelled appliance is installed in the kitchen,
extract ventilation can cause the spillage of flue
gases. Care must be taken to ensure ventilation
is reduced appropriately, as set out in the
Building Regulations. Kitchens with solid-fuel
appliances should not have extract fans fitted.

● The fan should not be sited where it is subject to
a direct source of heat in excess of 40˚C.

Operation

The S200 range of fans are available with various
control options suited to kitchen, bathroom and
toilet applications

SK200A – Dual speed operation, continuous at low
speed, boost via remote switch, light switch or pull cord.

SK200B2 – Dual speed operation by pull cord,
remote switch or light switch.

SK200MA – Dual speed operation with humidistat
to low speed with adjustable overrun timer to further
reduce humidity. Manual operation by pull cord,
remote switch or light switch to full speed, without
overrun timer.

SK200T – Single speed operation by pull cord,
remote switch or light switch with overrun timer for
adjustable time period.

To clean or service fan
and filter

WARNING: Fan must be isolated from mains
electricity supply before carrying out any
maintenance.

Wall Mounting rear exit

1

2

The fan and grille may now be cleaned using a
brush or damp cloth. Do not immerse in water

.

The filter may be cleaned in warm soapy water –

ensure filter is dry before re-fitting to fan.

NOTE: CLEANING OF THE SK200MA MUST BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Ducting

External Grille

● The unit can be mounted to the

wall either by rear entry or side
entry depended on mounting
position and access to the outside.

● The unit can be mounted in any

orientation to suit the room space.

● When installing wall mounted fans,

ensure that there are no buried
cables or pipes in the way. It is
recommended that this fan is
mounted 2.3m above floor level.

SK200 install AW 3.6.10 4/6/10 01:58 Page 2

Select supply
cable entry

See page 10 for wiring instructions

54

Wall Mounted with rear exit installation

Wall Mounted with side exit installation

9

11

2

10

1

3

8

A

A

Inside

Outside

>1˚

2

4

5

1

Ø

= 125mm

Ø

6

7

3

4

DO NOT DISTORT BACKPLATE WHEN FITTING

C

ut out for surface

m

ounted cabling

A

B

Remove 2 screws. Release cover with flat blade

screwdriver A then apply thumb pressure to release

catch in position B and gently pull free.

Fit 2 cover screws and tighten, ensure corners

clip into place

T

ighten 3 screws to secure

Slide the top of the cover mounting clip into alignment.
Push cover in centre to engage centre clip.

Replace grille

A

B

A

B

12

SK200 install AW 3.6.10 4/6/10 01:58 Page 4