Greenwood EL100 SELV Installation Instructions Manual

Installation Instructions

EL100 SELV (Safety Extra Low Voltage)
Axial Fans for Bathroom & Toilets

Greenwood Air Management Ltd

Brookside Industrial Estate

Rustington, West Sussex BN16 3LH

Tel: [phone]. Fax: [phone]

Email: [e-mail]

Internet: www.greenwood.co.uk

Environmental

Slot vent

Elite SELV Inst 26/8/04 3:36 pm Page 1

32

NOTES:

� Where an open-flued oil or gas- fuelled

appliance is installed in the kitchen, extract
ventilation can cause the spillage of flue
gases. Care must be taken to ensure
ventilation is reduced as appropriate, as set
out in the building regulations. The guide to
the regulations suggests that the reduced
provision should be an extract rate of 20 l/s
(72 m

3

/h) maximum. Kitchens with
solid-fuel appliances should not have extract
fans fitted.

� The fans should not be sited where

it would be subject to a direct source
of heat in excess of 40ºC.

� For window mounting do not install fans in

opening windows. Use the correct thickness
of glass for the size of window (at least 4
mm thick) if in doubt, contact a glazier.

� A clearance of 75 mm to be allowed on both

sides of fan for the removal of the internal
grille.

Operation

The Airvac Elite range of fans are single speed
SELV 12V axial flow extract fans to exceed
Building Regulation requirements for bathroom
and toilet ventilation. The remotely mounted
controller contains switch line control.

Types of controls and operation

as follows:

TYPE ‘T’

Operation by pull cord, light switch
or remote switch.

Integral pull cord will activate the fan for
pre-set overrun timer operation.
If wired into room light or remote switch the fan
will operate whilst the switch is on. Switching off
will activate the overrun timer.

TYPE ‘TR’

Operation by light switch or remote switch.

When wired into room light or remote switch the
fan will operate whilst the switch is on. Switching
off will activate the overrun timer.

TYPE ‘HTR’

Automatic operation by light switch or remote
switch.

The fans integral humidity sensor will operate the
fan whilst the RH exceeds the pre-set activation
point, When the RH is reduced back to the
activation point the linked overrun timer
continues to operate the fan for the pre-set time
period to ensure the RH level is further reduced
within the room to prevent ‘hunting’.

When wired into room light or remote switch the
fan will operate whilst the switch is on. Switching
off will activate the overrun timer.

� See Sensor / Timer Adjustments section for further details.

�

The Airvac Elite range of fans are fitted with electrical operated anti-backdraught
shutters which have a time delay to open or close.

Read all instructions before
commencing installations

Elite SELV Inst 26/8/04 3:36 pm Page 2

54

7

1

3

5

8

4

6

Window Mounting

EL100 SELV Ø = 118 mm ± 1 mm

Make sure
rubber cable
grommet is
fitted onto cable
before threading
cable through
fan back plate.

Ø

EL100 SELV

EW100

� For window mounting do

not install fans in opening
windows. Use the correct
thickness of glass for the size
of window (at least 4 mm thick)
if in doubt, contact a glazier.

� The components supplied are

suitable for the installation of fans
in windows from 4 mm single
glaze to 28 mm thick double­glazing.

To aid assembly,
smear the spigot
of the fan or lip of
seal with silicone
lubricant or silicone
polish.

2

SEE PAGE 8 FOR WIRING INSTRUCTIONS

25 mm long screws – Single glazing
38 mm long screws – 20 mm & 24 mm double glazing
50 mm long screws – 28 mm double glazing

Elite SELV Inst 26/8/04 3:36 pm Page 4