Greenway Home Products GEF252AEE User Manual
Elegant Fireplace Mantel
YEAR
ANNÉE
AÑO
1
I
N
-
H
O
M
E
W
A
R
R
A
N
T
Y
G
A
R
A
N
T
I
E
À
L
A
M
A
I
S
O
N
G
A
R
A
N
T
Í
A
E
N
S
U
P
R
O
P
I
A
C
A
S
A
with integrated sound system
Manteau de cheminée élégant
Elegante repisa de chimenea
Assembly Instructions
Instructions d'assemblage
Instrucciones de montaje
GEF252AEE
con sistema de sonido integrado
avec système sonore intégré
REV00
TIPS FOR THE ASSEMBLY OF
YOUR NEW MANTEL
• Before you begin assembly, locate the instructions and hardware. Take out all the parts and
compare them to the diagrams below. Be sure you have all the parts and can identify them.
• A helping hand is always good. Assemble your mantel with an adult assistant if possible. Some
pieces are heavy and will need to be held by a helper. Assembly time will take approximately 30-60 minutes.
TOP 1PC
ZZ.252AEE.01
RIGHT SIDE
PANEL
INTERIOR
1PC
ZZ.252AEE.06
RIGHT TOP SHELF 1PC
ZZ.252AEE.11
RIGHT LOWER PANEL
1PC
ZZ.252AEE.16
BASE 1PC
ZZ.252AEE.02
PANEL UNDERNEATH
THE TOP 1PC
ZZ.252AEE.07
LEFT BASE SHELF 1PC
ZZ.252AEE.12
CENTRAL PANEL 1PC
ZZ.252AEE.17
CENTRAL TOP SHELF
1PC
ZZ.252AEE.08
LEFT ADJUSTABLE SHELF
1PC
ZZ.252AEE.13
LEFT BACK
PANEL 1PC
ZZ.252AEE.18
LEFT SIDE
PANEL
EXTERIOR
1PC
ZZ.252AEE.03
CENTRAL SHELF 1PC
ZZ.252AEE.09
RIGHT INTERIOR SHELF
1PC
ZZ.252AEE.14
RIGHT BACK
PANEL 1PC
ZZ.252AEE.19
LEFT SIDE
PANEL
INTERIOR
1PC
ZZ.252AEE.04
LEFT LOWER PANEL
RIGHT SIDE
PANEL
EXTERIOR
1PC
ZZ.252AEE.05
LEFT TOP SHELF 1PC
ZZ.252AEE.10
1PC
ZZ.252AEE.15
SPEAKER 2PCS
ZZ.252AEE.20
2PCS
LEFT DOOR
1PC
ZZ.252AEE.21
2PCS
RIGHT DOOR
1PC
ZZ.252AEE.22
4PCS
CENTRAL DOOR 1PC
ZZ.252AEE.23
DOOR SUPPORTER
2PCS
SHELF MOUNTING
PEG 4PCS
WING NUT
38PCS
HARDWARE
21PCS
4PCS
1
GET READY TO START
Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or
exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the
hardware bag which is RED and located inside the packaging, taped to the top box. Be sure you DO
NOT discard any pieces. Use an appropriate screwdriver to insert and tighten all screws.
Step 1
Locate the base and place it on the floor. DO NOT put the base up
against the wall at this point in the assembly. You need to get behind the
mantel during the assembly process to insert and tighten several wing
nuts, lock washers, hinges and screws.
Step 2
Locate the left side panel (exterior) and position it on the left side
(exterior) of the base. Line up the 2 holes, insert and tighten the 2
wing nuts and lock washers.
Step 3
Locate the left back panel and slide it into
the groove shown on the base and the left
side panel. Locate the left lower panel.
Insert the 2 dowels into the dowel holes
located on the left side panel.
Step 4
Locate the left side panel (interior) and position it on the left side
(interior) of the base. Ensure the 2 dowels on the left lower panel
insert into the 2 holes on the left side (interior). Line up the 2
holes between the base and the left side panel (interior), insert
and tighten the 2 wing nuts and lock washers.
2
Loading...