Greenware Defendo 600, Defendo 1000, Defendo 1500, Defendo User Manual

1. Introduction

Thank you for purchasing the product. AVR-protected socket will automatically maintain a

constant voltage level to protect sensitive electronics from brownouts and overvoltages. With

its fashionable cabinet, it can be installed on a desk or wall without causing an unsightly or

unprofessional image, and will perfectly utilize a limited working environment.

Features:

 Provides AVR-protected sockets
 Provides stable output voltage through boost and buck stabilizer
 Accepts wide input voltage range
 Provides over-voltage protection (option)
 Provides Over-temperature protection (option)

2. Product Overview

 Power switch  Power LED: green lighting
 AC input  AVR LED: yellow lighting
 AVR-protected output receptacles  Modem/phone surge protection
 5V USB port (option)

3. Installation and Initial Startup

Inspection

Remove the unit from the shipping package and inspect it for damage that may

occurred during transportation. Notify the carrier and place of purchase if any

damage is found.

Placement & Storage Conditions

Install the unit in a protected area that is free of excessive dust and has adequate air flow.

Please place the unit away from other units at least 2.5cm to avoid interference. Do NOT block

the top or side air vents on the unit. Do not operation the unit in an environment where the

ambient temperature or humidity is outside the limits listed in the specifications. Operate the

unit in an environment free of excessive dust, mechanical vibration, inflammable gases and

explosive or corrosive atmospheres.

Connect to the Wall Outlet

Plug the input power cord of the unit to the wall outlet.

Connect the Loads

The AVR-protected receptacles will provide stable power to connected devices by boosting

and bucking the input power. Therefore, simply connect sensitive loads to AVR-protected

receptacles.

Connect Modem/Phone for Surge Protection

Connect a single modem/phone line into surge-protected “IN” outlet on the unit. Connect

from “OUT” outlet to the computer with phone line cable.

Turn On/Off the Unit

Turn on the unit by pressing the power switch to “RESET” position. Then, all connected
devices will be powered on.

DEFENDO Automatic Voltage Regulator

Quick Guide v.1.0

4. Mounting Unit

The unit can be mounted to a wall surface. There are two ways to position the unit: vertically

and horizontally.

1. Use a ruler to draw a straight line in 114 mm vertically or horizontally on the wall.

2. Use a sharp nail to puncture the center of the two ends to mark the wall.

(see below chart 1 as placing the unit horizontally)

3. Mount the unit by positioning the key-hole slots over the mounting nails. (see chart 2 and

chart 3)

Chart 1 Chart 2 Chart 3

114 mm distance between 2 holes Mounting horizontally Mounting vertically

5. Applications

CAUTION: The total power consumption of all equipment plugged into the voltage

regulator must not exceed its capacity*. A total load in excess of its capacity* will cause the

fuse to fault (blow).

*For the capacity of unit, please check the specifications.

The voltage regulator is designed for use with voltage sensitive equipment such as: a home

computer, monitor, inkjet printer, scanner or fax. It is also designed for use with home

electronics equipment such as television, stereos, CD players, VCRs, and DVD players, data

processing equipment, modems, typewriters, calculators, and telephone equipment.

Appliances not suitable for use with the product are items such as freezers, power tools, air

conditioners, dehumidifiers, blenders, or any device that employs an AC motor for operation.

Not for use with small fuel generators. Also excluded are life sustaining equipment.

When use the voltage regulator with an Uninterruptible Power Supply (UPS), connect the

UPS to the output of this product, then connect the product to the wall outlet.

6. Important Safety Warning (SAVE THESE INSTRUCTIONS)

To safely operate this voltage regulator, please read and follow all instructions

carefully. Read this manual thoroughly before attempting to unpack, install, or

operate. You may keep this quick guide for further reference.

CAUTION: The unit is designed only for use under the 50 Hz input frequency and pure sine

wave environment. Any other input frequency or wave form will effect the voltage range

and load capability.

CAUTION: Please DO NOT connect the unit to the environment with direct voltage or

simulated sine wave.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and

humidity controlled indoor area free of conductive contaminants. (See the specifications for

the acceptable temperature and humidity range.)

7 Specifications

Model

600

1000

1500

CAPACITY

600VA/300W

1000VA/500W

1500VA/750W

INPUT

Voltage

230 VAC

Voltage Range

184-284 VAC

Frequency

50 Hz

OUTPUT

Voltage Regulation

± 10%

Output Receptacles

Schuko x 3 / Universal x 3 / India x 3

INDICATOR

Power LED

Green lighting

AVR LED

Yellow lighting

Over-voltage LED
(option)

Red lighting

PHYSICAL

Dimension (DxWxH)

180 x 95 x 114 mm

Net Weight (kgs)

1.36

1.6

1.96

Environment

Humidity

0-90 % RH @ 0-40° C (non-condensing)

Noise Level

Less than 40 dB