GreenTech Pure Wash Owner's Manual
Owner’s Manual
2
2
3
4
5
6
7
8
9
12
Introduction
Specifications
Warnings & Important Info
Diagrams
Installation Requirements
Installation
Indicators & Alarms
Using your pureWash
Frequently Asked Questions
Internal Diagram
10Troubleshooting
12
13
Replacement Parts
Warranty Information
www.GreenTechEnv.com
Copyright © 2010 GreenTech Environmental: All Right Reserved
2
Introduction:
pureWash is an environmentally friendly appliance designed to work with your residential
washing machine, adding enhanced oxygen and Photo Catalytic Oxidizers to the cold water
supply. Water treated by pureWash aids in cleaning laundry and killing bacteria without
leaving residual detergent in the fabric. Many people nd they are allergic to detergents used
in washers and the detergents create an environmental problem as they are dispersed into the
waste water by washers.
e operation of pureWash is easy and convenient. Once your pureWash is properly installed,
you simply operate your washing machine following the manufacturer’s instructions. pureWash
is designed to automatically turn on as soon as the washer demands water for the wash cycle
and again for any rinse cycles. You will be able to see the production of enhanced oxidation
bubbles through the viewing window as it glows blue. When the water stops owing, your
pureWash will automatically turn o.
Technical Specications:
Model: ........................... pureWash (Standard Flow)/pureWash (Low Flow)
Electrical INPUT: .....................................AC 100-240V/50-60Hz
Electrical OUTPUT: ............................................. DC 12V, 3A
Water Pressure Required: .............................................40-75 psi
Water Operating Temperature: ............................... Use Cold Water Only
Dimensions: .............................................. 16.4” x 7.9” x 3.7”
Weight: ............................................................. 5 lbs
Records:
Purchase Date: ___________________________________________________________
Model Number: __________________________________________________________
Serial Number: ___________________________________________________________
Distributor Name: ________________________________________________________
Distributor Phone: ________________________________________________________
3
Warning & Important Info:
Disconnect power before servicing.
Do not mount your pureWash vertically or at any angle. See installation instructions.
(unit is designed to operate horizontally ONLY).
Do not operate the unit with the cover removed.
pureWash is designed for residential use only and is not intended for use in a
commercial or industrial setting.
Water treated by pureWash is intended for laundry ONLY. It is not approved for
drinking or ingesting.
Do not use an extension cord or power adapter other than the one provided with your
pureWash unit.
pureWash is intended for use with COLD WATER ONLY, however the hot water
hose should remain connected to the washer and supply faucet to prevent backow leaks.
To avoid the possibility of water damage (i.e. a hose leak) it is recommended that you
always turn o the water supply valves/faucets when the washing machine is not in use.
Risk of water leaks from ruptured hoses could occur with major water pressure surges.
To maintain pressure seal, maximum inlet water pressure is 75 psi.
Never install the pureWash in areas where water may freeze. pureWash will always
maintain some water in the unit and freezing can cause damage to internal components.
pureWash is not recommended for use in homes with high iron content in their water.
If your water has high iron content, consult a water quality expert for available options.
Your pureWash can be cleaned with a damp soft cloth. Do not clean your pureWash
with harsh chemicals, abrasives or cleaners.
Before using, please read this Owner’s Manual carefully.
Copyright © 2010 GreenTech Environmental: All Right Reserved
4
Front Diagram:
Rear Diagram:
LEFT Side Diagram:
Water
Outlet
Mounting
Hole
D/C Adapter
Plug-in
Cover
Release
Tab
Water
Intlet
Mounting
Hole
5
Installation Requirements:
Electrical Requirements:
• pureWash requires 120 Volt 60 Hz power on a 15 amp fuse or circuit breaker.
• Never use an extension cord or a power adapter other than the one provided with pureWash.
Water Requirements:
• Water pressure of 40 to 75 psi is required for pureWash to operate correctly and safely.
• To avoid the possibility of water damage (i.e. a hose leak) it is recommended that you
always turn o the water supply valves/faucets when the washing machine is not in use.
• Water quality may aect the performance of your pureWash. If you have water quality
concerns, such as high iron content, consult a water ltration expert.
• Some later model high-eciency washing machines require water from both the cold and
hot water supplies even if a cold water cycle is selected. In this case, a Y-valve will connect
both the cold and hot water hoses from the pureWash outlet hose to the washing machine.
Location Requirements:
• Never install the pureWash in areas where water may freeze. pureWash will always
maintain some water in the unit and freezing can cause damage to internal components.
Prior to Installation:
1. Remove your pureWash from its packaging and inspect for any shipping damage.
2. Turn o the hot and cold water supplies/faucets to your washing machine.
3. Remove the cold water hose from the cold water faucet.
Loading...