GREEN SERIES FITNESS CIR-TM7000E-G1 Owner's Manual

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

John C. Jensen

Owner's Manual

CIR-UB7000E-G1

Full Commercial

Install Date: _________________________ Serial Number: ________________________

Light Commercial

Full Commercial

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

1

John C. Jensen

TABLE OF CONTENTS

SAFETY
PRECAUTIONS …………………………………………………..……………………..…..2-5

Important voltage information, grounding instructions, how often you exercise, how hard
you exercise, how long you exercise, beginner upright bike program, target heart rate
zone.

TECHNICAL
SPECIFICATIONS ………………………………………………………………………….….6

UNPACKING &
ASSEMBLY ………………………………………………………………………………...7-17

Parts, hardware kit and assembly drawing

WARM UP & COOL
DOWN ……………………………………………………….….………………………..……18

SETTINGS …………………………………………………………………………………….19

WiFi and TV

PROGRAMS ……………………………………………….…………………….….…....20-30

Control panel function and programs

OPERATION ……………………………………………………………………….…..…31-32

MAINTENANCE ……………………………………………………………...……...............33

PARTS …………………………………………………………………………………………34
EXPLODED DRAWINGS ………………………………………………………………..35-37

WARRANTY ………………………………………………………………………….......38-40

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

2

John C. Jensen

SAFETY PRECAUTIONS

Location of the Upright Bike

Before assembling the unit, verify the chosen site meets the following criteria:

• Area is well lit and well ventilated.

• Surface is structurally sound and properly leveled.

• Free area for access to the unit and emergency dismount. Minimum clearance is 24 inches (0.6 meters) on

the sides of the unit and 78.7 inches (2.0 meters) behind the unit.

• Adjacent units may share the free area.

• Place in a location away from direct sunlight. The intense UV light can cause discoloration on the plastics.

• Locate your upright bike in an area with cool temperatures and low humidity.

• Do not install, use or store the upright bike in an area of high humidity, such as in the vicinity of a steam

room, sauna, indoor pool, garage, covered patio, near water or outdoors. Exposure to extensive water
vapor, chlorine and/or bromine could adversely affect the electronics as well as other parts of the unit.

The below minimum spacing recommendations are based on a combination of the ASTM (U.S.) voluntary standards and EN
(European) regulations as of October 1, 2012, for access, passage around, and emergency dismount:

ASTM standards are voluntary and may not reflect current industry standards. The actual area for access, passage around,
and emergency dismount is the responsibility of the facility. The facility should consider the total space requirements for
training on each unit, voluntary and industry standards, and any local, state, and federal regulations. Standards and
regulations are subject to change at any time.

Careful consideration should be given to the requirements of the Americans with Disabilities Act (ADA), US Code 28 CFR
(see Section 305).

In compliance with the ADA (American Disabilities Act) there must be clear floor space of at least 30 inches by 48 inches and
be served by an accessible route for at least one of each type of exercise equipment. If the clear space is enclosed on three
sides (e.g., by walls or the equipment itself), the clear space must be 36 inches by 48 inches.

Important: These spacing recommendations should be used when positioning equipment away from sources of heat,

such as radiators, heat registers, and stoves. Avoid temperature extremes.

24”

600mm

79”

2000mm

12”

300mm

24”

600mm

24”

600mm

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

3

John C. Jensen

SAFETY PRECAUTIONS

Environment

The unit is designed to function normally in an environment with a relative humidity range of 30% to 75%. The unit can be
shipped and stored in a relative humidity range of 10% to 90%. Climatic dry air may cause static electricity. During a
workout, a user may experience a shock due to a buildup of static electricity on the body and the discharge path of the unit.
If static electricity is experienced, increase humidity to a comfortable level through the use of a humidifier.

Temperature

The unit is designed to function in an environment with an ambient temperature range of 50°F (10°C) to 104°F (40°C).
The unit can be shipped and stored in an environment with an ambient temperature range of 32°F (0°C) to 140°F (60°C).

Electrical Power Requirements

The power requirements for this upright bike are a grounded circuit rated for the following:

• 115 VAC, 50/60 HZ, 15A

Shock and electrocution hazard.

• Connect unit to a grounded outlet.

• Do not use a voltage adapter or extension cord.

• Important Voltage Information

• Before plugging the power cord into an electrical outlet, verify that the voltage requirements for your area match the

voltage of the upright bike that you have received. The power requirements for the upright bike include a grounded,
dedicated circuit, rated for one of the following figure. See the serial number decal for the exact voltage
requirements of your upright bike.

• WARNING: Don't attempt to use this unit with an unapproved voltage adapter. All voltage adapters MUST be

approved and supplied by Green Series Fitness prior to use.

• Don't attempt to use this unit with an extension cord which does not meet Green Series Fitness criteria of the following;

12 gauge SO3, maximum of 25 foot length with a 20 amp rating.

Grounding Instructions

This equipment must be grounded. If it should malfunction or break down, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock.
This equipment is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Please make sure that the equipment is connected to an outlet having the same configuration as the plug. Do not use a
ground plug adapter to adapt the power cord to a non-grounded outlet.

120V EURO PLUG 208-240V

NEMA 5-20 CEE 7/7 NEMA 6-15

The power requirements for the equipment includes a grounded, dedicated circuit, rated for one of the
following:
120 VAC 5%, 60HZ and 15 amps;
208/240 VAC, 60HZ, 15 amps
240 VAC 5%, 50HZ and 15amps.

WARNING

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

4

John C. Jensen

SAFETY PRECAUTIONS

Waste Disposal

Products are recyclable. At the end of its useful life please dispose of this
article correctly and safely (local refuse sites).

▪The running belt must be set up on firm even ground. Ensure that the power cable is not pinched and that on-one can trip
over it.

▪Never touch the moving belt with your hands. Also ensure that there are no objects close to the belt or the rollers which
could be pulled into it thus causing injury or damaging the unit itself.

▪Repairs on the electrical components in the unit should be carried out by qualified persons only.
▪The upright bike has an emergency stop mechanism for your safety. Before starting your workout, fasten the cord of the

safety key to your clothing. If the upright bike has been shut down by removing the safety key, restart it by reinserting the
key. An automatic restart of the upright bike belt does not occur. Further instructions concerning the handling of the safety
cut-out can be found in the operating instructions for the training computer.

Thank you for your purchasing our products. Even though we go to great efforts to ensure the quality of each product,
occasional error, and/or omissions do occur. In any event should you find this product to be defective or missing parts
please contact us.

IMPORTANT: Read all instructions and warnings before assembly and operation.

IMPORTANT SAFETY INSTRUCTIONS

When using equipment, basic precautions should always be followed, including the following:
Read all instructions before using the Upright bike.

DANGER - To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet

immediately after using and before cleaning.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons:

1. The equipment should never be left unattended when plugged in. Unplug from outlet when not in use and before
putting on or taking off parts.

2. Close supervision is necessary when the equipment is used by, on, or near children, invalids, or disabled
persons.

3. Use the equipment only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacture.

4. Never operate the equipment if it has a damaged cord or plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return the equipment to a service center for examination and repair.

5. Do not carry the equipment by supply cord or use cord as a handle.

6. Keep the cord away from heated surfaces.

7. Never operate the equipment with the air openings blocked. Keep the air openings free of lint, hair, and the like.

8. Never drop or insert any object into any opening.

9. Do not use outdoors.

10. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

11. To disconnect, turn all controls to the OFF position, then remove plug from outlet.

12. Connect the equipment to a properly grounded outlet only. See Grounding Instructions.

13. The equipment is intended for commercial use.

14. Store the safety key in a secured location while not in use and keep away from children.

15. Maximum user weight: 450Ibs (204 kg) .

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

5

John C. Jensen

SAFETY PRECAUTIONS

CONSULT A PHYSICIAN IMMEDIATELY

Warning: Before starting any exercise program consult your physician. This is especially important for individuals

over the age of 35 or persons with preexisting health problems. Read all instructions before using any fitness
equipment. We assume no responsibility for personal injury damage sustained by or through the use of this .

How often you exercise:

You should exercise three to four times a week to improve your cardiovascular and muscle fitness.

How hard you exercise:

Intensity of exercise is reflected in your heart rate. Exercise must be sufficiently rigorous to strengthen your heart muscle
and condition your cardiovascular system. Only your doctor can prescribe the target training heart range for you. Before
starting any exercise program consult your physician.

How long you exercise:

Sustained exercise conditions your heart, lungs and muscles. The longer you are able to sustain exercise within your target
heart range, the greater the aerobic benefits. To begin maintain 2~3 minutes of steady, rhythmic exercise, then check your
heart rate.

BEGINNER UPRIGHT BIKE PROGRAM

EXERTION LEVEL

DURATION

WEEK 1

Easy

6~12 minutes

WEEK 2

Easy

10~16 minutes

WEEK 3

Moderate

14~20 minutes

WEEK 4

Moderate

18~24 minutes

WEEK 5

Moderate

22~28 minutes

WEEK 6

Slightly higher or slightly lower

20 minutes

WEEK 7

Add interval training

3 minutes at moderate exertion with 3 minutes at higher
exertion for 24 minutes

UTARGET HEART RATE ZONE

220-your age = maximum heart zone

You do not want to workout at your
maximum heart rate. The recommended
Heart Rate Zone is a percentage of your
maximum heart rate. Between 65% and
80% of your maximum heart rate.

* Lower limit of Target Heart Rate Zone
=maximum heart rate X 0.6

* Upper limit of Target Heart Rate Zone
=Maximum heart rate X 0.8

(This is recommended by American Heart
Association. Before starting exercise
program, please consult your physician
to understand your physical situation)

*This appliance is not intended for use by persons
(including children) with reduced physical sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

6

John C. Jensen

TECHNICAL SPECIFICATIONS

The Serial Number of the products

The serial number contains of ten values. The location of the serial number shows as the figure.

SPECIFICATIONS:

Length: 113 cm
Width: 69cm
Weight of product: 66 kgs (145 lbs)

Program：6 Preset Program, 3 Goal, 4 HRC, Physical Test, Virtual GO
Standard features: Time, Speed, Incline, Heart Rate, Distance, Calories, Program Profile

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

7

John C. Jensen

UNPACKING & ASSEMBLY

Parts

Main frame / 1pc

Console set 1pc

Handlebar 1pc

Pedal with strap 1set

Upper water bottle
holder cover 1pc

Lower water bottle
holder cover 1pc

Rear base tube cover

1pc

Upright tube cover, right
/ left 1 set

#3-6

#5-1

#5-2

#5-25

#5-15

#5-9

#5-8

#5-21

#5-22

#5-6

#5-11

#5-10

Console upright Tube /

1pc

Front base tube

1pc

Rear base tube

1pc

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

8

John C. Jensen

UNPACKING & ASSEMBLY

Hardware kit

X 2

(lower water bottle

holder cover)

M4x20mm

X 1

Allen wrench

(6mm)

X 1

Allen wrench

(5mm) M15/M15

M4x12mm

X 2

(rear stabilizer)

#5-7

#5-24

M8x20mm

X 1

(handlebar)

#5-12

M8x65mm

X 2

(handlebar)

#5-19

M8 curve

X 2

(handlebar)

#5-20

X 1

Step2

Step7

Step8

#5-14

M8 Flat

Washer

#5-13

M8 Lock

Washer

X 1

(handlebar)

X 3

(handlebar)

X 1

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

9

John C. Jensen

UNPACKING & ASSEMBLY

Unpack your bike where you plan to use it. Being careful not to damage the plastic pieces and other components. Place
your bike on a level flat surface. It is recommended that you place a protective covering on your floor.

Step 1: Assemble Front/Rear Base Tube with Main Frame

1). Remove the pre-lock screws on the front and back base tube.

2). Using a Allen wrench (6mm), install the (2) M8x20mm screws, lock washers, and flat washers securing the front
base tube to the main frame.

3). Using a Allen wrench (6mm), install the (2) M8x20mm screws, lock washers, and flat washers securing the back
base tube to main frame.

X1

X1

X 4

M8x20mm

X 4

M8 Lock

Washer

#5-1

#5-2

#5-3

#5-4

X 4

M8 Flat

Washer

#5-5

Allen wrench

(6mm)

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

10

John C. Jensen

UNPACKING & ASSEMBLY

Step 2: Assembling Rear Stabilizer Cover to the Main Frame

1). Using a Allen wrench (6mm) install the (2) M4x12mm screws to secure the housing of back base tube to main

frame.

X1

X 2

M4x12mm

#5-6

#5-7

Allen wrench

(6mm)

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

11

John C. Jensen

UNPACKING & ASSEMBLY

Step 3: Assemble Pedal Set to the Crank

1). Use wrench to clockwise fix right pedal set to crank set.

2). Use wrench to counterclockwise fix left pedal set to crank set.

X1 set

#5-9

#5-8

www.GreenSeriesFitness.com ©April 2017 Call Toll free at [phone]

CIR-UB7000E-G1 Revision 1.2

12

John C. Jensen

UNPACKING & ASSEMBLY

Step 4: Console Wire Routing

1). Remove the pre-lock screws on the main frame.

2). Use the guide wire to route the console wire and cable connecter through the console upright tube. Do not remove
the guide wire from the top of the console upright tube. Leave the guide wire secured to the top of the tube until
Step 9.

X1

#3-6