GreenPower EL100, EL150, EL150SCPC Installation Instructions Manual
Web: www.greenwood.co.uk
Environmental
Slotvent
Email: info@greenwood.co.uk
Tel: (01903) 771021 Fax: (01903) 782398
Rustington, West Sussex, BN16 3LF.
Greenwood House, Brookside Avenue,
Greenwood Air Management Ltd
EL100, EL150U, EL150
& EL150SCPC Axial Fans
Bathroom, Toilets, Utility Rooms and Kitchens
Installation Instructions
2
Operation
� See Sensor / Timer Adjustments section for further details.
�
The Airvac Elite range of fans are fitted with electrical operated anti-backdraught
shutters which have a time delay to open or close.
The Airvac Elite range of fans are single and dual speed
axial flow extract fans designed to exceed Building
Regulation requirements for bathroom, toilet, kitchen or
utility room ventilation.
Types of controls and operation as follows:
TYPE EL100, EL150U, EL150
Operation by light switch, remote switch or
remote sensor.
TYPE ‘PC’ AND ‘UPC’
Operation by pull cord.
TYPE ‘TR’
Operation by light switch or remote switch.
When wired into room light or remote switch the fan will
operate whilst the switch is on. Switching off will activate
the overrun timer.
TYPE ‘T’
Operation by pull cord, light switch or remote switch.
Integral pull cord will activate the fan for pre-set overrun
timer operation. If wired into room light or remote switch
the fan will operate whilst the switch is on. Switching off
will activate the overrun timer.
TYPE ‘DT’
Automatic operation by light switch or remote switch.
Pre-set delay timer facility allows up to two minutes of
fan operation before the overrun timer is actuated. If fan
is switched off after the delay timer setting the integral
overrun timer will operate the fan for the pre-set time
period.
TYPE ‘HTR’
Automatic operation by light switch or remote switch.
The fans integral humidity sensor will operate the fan
whilst the RH exceeds the pre-set activation point, When
Read all instructions before
commencing installations
NOTES:
� Where an open-flued oil or gas- fuelled
appliance is installed in the kitchen, extract
ventilation can cause the spillage of flue
gases. Care must be taken to ensure
ventilation is reduced as appropriate, as set
out in the building regulations. The guide to
the regulations suggests that the reduced
provision should be an extract rate 20 l/s
3
(72 m
/h) maximum. Kitchens with solid-fuel
appliances should not have extract fans fitted.
� The fans should not be sited where it would
be subject to a direct source of heat in excess
of 40ºC.
� For window mounting do not install fans in
opening windows. Use the correct thickness
of glass for the size of window (at least 4
mm thick) if in doubt, contact a glazier.
� A clearance of 75 mm to be allowed on both
sides of fan for the removal of the internal
grille.
Operation
32
Operation
The Airvac Elite range of fans are single and dual speed
axial flow extract fans designed to exceed Building
Regulation requirements for bathroom, toilet, kitchen or
utility room ventilation.
Types of controls and operation as follows:
TYPE EL100, EL150U, EL150
Operation by light switch, remote switch or
remote sensor.
TYPE ‘PC’ AND ‘UPC’
Operation by pull cord.
TYPE ‘TR’
Operation by light switch or remote switch.
When wired into room light or remote switch the fan will
operate whilst the switch is on. Switching off will activate
the overrun timer.
TYPE ‘T’
Operation by pull cord, light switch or remote switch.
Integral pull cord will activate the fan for pre-set overrun
timer operation. If wired into room light or remote switch
the fan will operate whilst the switch is on. Switching off
will activate the overrun timer.
TYPE ‘DT’
Automatic operation by light switch or remote switch.
Pre-set delay timer facility allows up to two minutes of
fan operation before the overrun timer is actuated. If fan
is switched off after the delay timer setting the integral
overrun timer will operate the fan for the pre-set time
period.
the RH is reduced back to the activation point the linked
overrun timer continues to operate the fan for the pre-set
time period to ensure the RH level is further reduced
within the room to prevent ‘hunting’.
When wired into room light or remote switch the fan will
operate whilst the switch is on. Switching off will activate
the overrun timer.
TYPE ‘PIR’
Automatic operation by an integral passive infra-red sensor
which controls the fan by detecting body movement within
7 metres. The sensor picks up the movement and the fan
is activated. Once movement ceases the overrun timer will
run for the pre-set time period.
TYPE ‘MA’
Dual speed, automatic operation to slow speed and
manual operation to normal speed.
Integral humidistat operates fan to slow speed whilst the
RH (relative humidity) exceeds pre-set activation point.
When RH is reduced to the pre-set level the linked timer
continues fan at slow speed for the nominated overrun
period, further lowering the humidity level.
Manual operation by remote switch/light switch
operates the fan at normal speed.
Humidistat adjustable 50 – 90% RH.
Adjustable overrun timer (up to 30mins).
TYPE ‘SCPC’
Operation by pullcord or remote switch.
Single speed operation at pre-set rate for use where
open flued gas appliances are present. At installation
the variable speed control is set and sealed to prevent
spillage from gas appliance.
32
32
the RH is reduced back to the activation point the linked
overrun timer continues to operate the fan for the pre-set
time period to ensure the RH level is further reduced
within the room to prevent ‘hunting’.
When wired into room light or remote switch the fan will
operate whilst the switch is on. Switching off will activate
the overrun timer.
TYPE ‘PIR’
Automatic operation by an integral passive infra-red sensor
which controls the fan by detecting body movement within
7 metres. The sensor picks up the movement and the fan
is activated. Once movement ceases the overrun timer will
run for the pre-set time period.
3
The Airvac Elite range of fans are single and dual speed
axial flow extract fans designed to exceed Building
Regulation requirements for bathroom, toilet, kitchen or
utility room ventilation.
Types of controls and operation as follows:
TYPE EL100, EL150U, EL150
Operation by light switch, remote switch or
remote sensor.
TYPE ‘PC’ AND ‘UPC’
Operation by pull cord.
TYPE ‘TR’
Operation by light switch or remote switch.
When wired into room light or remote switch the fan will
operate whilst the switch is on. Switching off will activate
the overrun timer.
TYPE ‘T’
TYPE ‘HTR’
Operation by pull cord, light switch or remote switch.
Automatic operation by light switch or remote switch.
Integral pull cord will activate the fan for pre-set overrun
The fans integral humidity sensor will operate the fan
timer operation. If wired into room light or remote switch
whilst the RH exceeds the pre-set activation point, When
the fan will operate whilst the switch is on. Switching off
the RH is reduced back to the activation point the linked
will activate the overrun timer.
overrun timer continues to operate the fan for the pre-set
time period to ensure the RH level is further reduced
TYPE ‘DT’
within the room to prevent ‘hunting’.
Automatic operation by light switch or remote switch.
When wired into room light or remote switch the fan will
Pre-set delay timer facility allows up to two minutes of
operate whilst the switch is on. Switching off will activate
fan operation before the overrun timer is actuated. If fan
the overrun timer.
is switched off after the delay timer setting the integral
overrun timer will operate the fan for the pre-set time
period.
TYPE ‘HTR’
Automatic operation by light switch or remote switch.
The fans integral humidity sensor will operate the fan
whilst the RH exceeds the pre-set activation point, When
� See Sensor / Timer Adjustments section for further details.
The Airvac Elite range of fans are fitted with electrical operated anti-backdraught
�
shutters which have a time delay to open or close.
the RH is reduced back to the activation point the linked
TYPE ‘MA’
overrun timer continues to operate the fan for the pre-set
Dual speed, automatic operation to slow speed and
time period to ensure the RH level is further reduced
manual operation to normal speed.
within the room to prevent ‘hunting’.
Integral humidistat operates fan to slow speed whilst the
RH (relative humidity) exceeds pre-set activation point.
When wired into room light or remote switch the fan will
When RH is reduced to the pre-set level the linked timer
operate whilst the switch is on. Switching off will activate
continues fan at slow speed for the nominated overrun
the overrun timer.
period, further lowering the humidity level.
TYPE ‘PIR’
Manual operation by remote switch/light switch
Automatic operation by an integral passive infra-red sensor
operates the fan at normal speed.
which controls the fan by detecting body movement within
Humidistat adjustable 50 – 90% RH.
7 metres. The sensor picks up the movement and the fan
Adjustable overrun timer (up to 30mins).
is activated. Once movement ceases the overrun timer will
run for the pre-set time period.
TYPE ‘SCPC’
Operation by pullcord or remote switch.
TYPE ‘MA’
Single speed operation at pre-set rate for use where
Dual speed, automatic operation to slow speed and
open flued gas appliances are present. At installation
manual operation to normal speed.
the variable speed control is set and sealed to prevent
Integral humidistat operates fan to slow speed whilst the
spillage from gas appliance.
RH (relative humidity) exceeds pre-set activation point.
When RH is reduced to the pre-set level the linked timer
continues fan at slow speed for the nominated overrun
period, further lowering the humidity level.
Manual operation by remote switch/light switch
operates the fan at normal speed.
Humidistat adjustable 50 – 90% RH.
Adjustable overrun timer (up to 30mins).
TYPE ‘SCPC’
Operation by pullcord or remote switch.
Single speed operation at pre-set rate for use where
open flued gas appliances are present. At installation
the variable speed control is set and sealed to prevent
spillage from gas appliance.
Loading...