Greenheck ECV Series, ECV-10, ECV-30, ECV-20 Installation, Operation And Maintenance Manual

Page 1

Document 480955

Model ECV

Energy Core Ventilator

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with these instructions will result in voiding of the product warranty and may result in personal injury and/or property damage.

Energy Recovery & Make-Up Air Technical Support

Call 1-800-240-0870, press 1 for Service

General Safety Information

Only qualiﬁed personnel should install this system. Personnel should have a clear understanding of these instructions and should be aware of general safety precautions. Improper installation can result in electric shock, possible injury due to coming in contact with moving parts, as well as other potential hazards. Other considerations may be required if high winds or seismic activity are present. If more information is needed, contact a licensed professional engineer before moving forward.

DANGER

Always disconnect power before working on or near this equipment. Lock and tag the disconnect switch or breaker to prevent accidental power up.

CAUTION

When servicing the unit, the internal components may be hot enough to cause pain or injury. Allow time for cooling before servicing.

CAUTION

Precaution should be taken in explosive atmospheres.

1. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC), the National Fire Protection Agency (NFPA), where applicable. Follow the Canadian Electrical Code (CEC) in Canada.

2. All moving parts must be free to rotate without striking or rubbing any stationary objects.

3. Unit must be securely and adequately grounded.

4. Do not spin fan wheel faster than maximum cataloged fan RPM. Adjustments to fan speed signiﬁcantly effects motor load. If the fan RPM is changed, the motor current should be checked to make sure it is not exceeding the motor nameplate amps.

5. Do not allow the power cable to kink or come in contact with oil, grease, hot surfaces or chemicals. Replace cord immediately if damaged.

6. Verify that the power source is compatible with the equipment.

7. Never open access doors to the unit while it is running.

Energy Core Ventilator 1

Page 2

Table of Contents

Unit Overview

Unit Overview . . . . . . . . . . . . . . . . . . . . 2

Receiving, Handling and Storage . . . . . . . . . 3

Installation

Outdoor and Indoor Mounting Options . . . . . . . 4

Dimensional Data and Weights . . . . . . . . . . . 4

Service Clearances . . . . . . . . . . . . . . . . . 5

Access Panel Locations . . . . . . . . . . . . . . . 5

Handling . . . . . . . . . . . . . . . . . . . . . . . 6

Lifting . . . . . . . . . . . . . . . . . . . . . . . . 6

Roof Curb Mounting. . . . . . . . . . . . . . . . . 7

Curb Outside Dimensions and Weights . . . . . . . 7

Ductwork Connections . . . . . . . . . . . . . . . 8

Rail Mounting / Layout . . . . . . . . . . . . . . . 8

Electrical Information

General Electrical Information . . . . . . . . . . . . 9

Control Center Components . . . . . . . . . . . .10

Optional Accessory Wiring Schematics. . . . . 10-11

Unit Overview

Basic Unit . . . . . . . . . . . . . . . . . . . . . .11

Optional Component Overview

Economizer . . . . . . . . . . . . . . . . . . . . .12

Frost Control. . . . . . . . . . . . . . . . . . . . .12

Variable Frequency Drive . . . . . . . . . . . . . .12

Sensor . . . . . . . . . . . . . . . . . . . . .12

Dirty Filter Switch . . . . . . . . . . . . . . . . . .12

Start-Up

General . . . . . . . . . . . . . . . . . . . . . . .13

Pre Start-Up Checklist . . . . . . . . . . . . . . .13

Special Tools Required . . . . . . . . . . . . . . .13

Start-Up Checklist. . . . . . . . . . . . . . . . . .13

Optional Accessories Checklist . . . . . . . . . . .14

Start-Up Components

Fans . . . . . . . . . . . . . . . . . . . . . . . . .15

Fan Performance Modifications . . . . . . . . . . .15

Fan Belt Drives . . . . . . . . . . . . . . . . . . .15

Belt Drive Installation . . . . . . . . . . . . . . . .15

Direction of Fan Wheel Rotation . . . . . . . . . .15

Fan RPM. . . . . . . . . . . . . . . . . . . . . . .15

Optional Start-Up Components

Dirty Filter Switch . . . . . . . . . . . . . . . . . .16

Economizer . . . . . . . . . . . . . . . . . . . . .16

Frost Control. . . . . . . . . . . . . . . . . . . . .17

Proportional Control . . . . . . . . . . . . . .17

Vari-Green® EC Motors . . . . . . . . . . . . . . .17

Variable Frequency Drives. . . . . . . . . . . . 18-20

Routine Maintenance . . . . . . . . . . . . . . 20-21

Troubleshooting

Economizer Alarms . . . . . . . . . . . . . . . . .22

Airflow . . . . . . . . . . . . . . . . . . . . . . . .23

Unit . . . . . . . . . . . . . . . . . . . . . . . 24-25

Maintenance Log . . . . . . . . . . . . . . . . 26-27

Our Commitment . . . . . . . . . . . . . Backcover

Basic Unit

The unit is prewired such that when a call for outside air is made (via ﬁeld-supplied 24 VAC control signal wired to unit control center), the supply and exhaust fans are energized and optional motorized dampers open. The unit is normally interlocked (24 volt) to the rooftop air handler. When the rooftop air handler starts, the auxiliary contactor in the air handler closes to start the unit.

Summer Operation

Outdoor air is preconditioned (temperature and moisture levels are decreased) by the transfer of energy from the cooler, drier return air through the energy recovery core. The preconditioned air is typically mixed with return air going back to the air handler for final conditioning.

Winter Operation

Outdoor air is preconditioned (temperature and moisture levels are increased) by the transfer of energy from the warmer, more humid return air through the energy recovery core. The preconditioned air is typically mixed with return air going back to the air handler for final conditioning.

Exhaust Air

Summer

Operation

Supply Air

82° F

88 grains/lb.

Outdoor Air

95° F

125 grains/lb.

Return Air

75° F

50% RH

Energy Core Ventilator2

Page 3

Receiving

This product may have been subject to road salt during transit. If so, immediately wash off all visible white reside from all exterior surfaces. Upon receiving the product, check to ensure all items are accounted for by referencing the delivery receipt or packing list. Inspect each crate or carton for shipping damage before accepting delivery. Alert the carrier if any damage is detected, do not refuse shipment. The customer shall make notation of damage (or shortage of items) on the delivery receipt and all copies of the bill of lading should be countersigned by the delivering carrier. If damaged, immediately contact your manufacturer’s representative. Any physical damage to the unit after acceptance is not the responsibility of the manufacturer.

Handling

Units are to be rigged and moved by the lifting brackets provided or by the skid when a forklift is used. Location of brackets varies by model and size. Handle in such a manner as to keep from scratching or chipping the coating. Damaged ﬁnish may reduce ability of unit to resist corrosion.

Unpacking

Verify that all required parts and the correct quantity of each item have been received. Inspect interior of unit cabinet for any shipped loose items. If any items are missing, report shortages to your local representative to arrange for obtaining missing parts. Sometimes it is not possible that all items for the unit be shipped together due to availability of transportation and truck space. Conﬁrmation of shipment(s) must be limited to only items on the bill of lading.

Storage

Units are protected against damage during shipment. If the unit cannot be installed and operated immediately, precautions need to be taken to prevent deterioration of the unit during storage. The user assumes responsibility of the unit and accessories while in storage. The manufacturer will not be responsible for damage during storage. These suggestions are provided solely as a convenience to the user.

The ideal environment for the storage of units and accessories is indoors, above grade, in a low humidity atmosphere which is sealed to prevent the entry of blowing dust, rain, or snow. Units designed for outdoor applications may be stored outdoors. All accessories must be stored indoors in a clean, dry atmosphere.

Indoor

Maintain temperatures evenly to prevent condensation. Remove any accumulations of dirt, water, ice, or snow and wipe dry before moving to indoor storage. To avoid condensation, allow cold parts to reach room temperature. Leave coverings loose to permit air circulation and to allow for periodic inspection.

The unit should be stored at least 3½ in. (89 mm) off the ﬂoor. Clearance should be provided to permit air circulation and space for inspection.

Outdoor

The unit should be placed on a level surface to prevent water from leaking into the unit. The unit should be elevated so that it is above water and snow levels. Ensure sufﬁcient support to prevent unit from settling into soft ground. Locate parts far enough apart to permit air circulation, sunlight, and space for periodic inspection. To minimize water accumulation, place all unit parts on blocking supports so that rain water will run off.

Do not cover parts with plastic ﬁlm or tarps as these cause condensation of moisture from the air passing through heating and cooling cycles.

Inspection and Maintenance

While in storage, inspect units once per month. Keep a record of inspection and maintenance performed.

If moisture or dirt accumulations are found on parts, the source should be located and eliminated. At each inspection, rotate the fan wheel by hand ten to ﬁfteen revolutions to distribute lubricant on motor. If paint deterioration begins, consideration should be given to touch-up or repainting. Units with special coatings may require special techniques for touch-up or repair.

Machined parts coated with rust preventive should be restored to good condition promptly if signs of rust occur. Immediately remove the original rust preventive coating with petroleum solvent and clean with lint-free cloths. Polish any remaining rust from surface with crocus cloth or ﬁne emery paper and oil. Do not destroy the continuity of the surfaces. Wipe thoroughly clean with Tectyl hard to reach internal surfaces or for occasional use, consider using Tectyl or the equivalent.

506 (Ashland Inc.) or the equivalent. For

511M Rust Preventive, WD-40®

Removing from Storage

As units are removed from storage to be installed in their ﬁnal location, they should be protected and maintained in a similar fashion until the equipment goes into operation.

Prior to installing the unit and system components, inspect the unit assembly to make sure it is in working order.

1. Check all fasteners, set screws on the fan, wheel, bearings, drive, motor base, and accessories for tightness.

2. Rotate the fan wheel(s) by hand and assure no parts are rubbing.

Energy Core Ventilator 3

Page 4

Installation

Outdoor Mounting Options

EXHAUST AIR DISCHARGE

SUPPLY AIR DISCHARGE

(NON ELECTRICAL SIDE)

Outdoor Air Discharge Bottom

Indoor Mounting Options

EXHAUST AIR DISCHARGE

SUPPLY AIR DISCHARGE

(NON ELECTRICAL SIDE)

EXHAUST AIR DISCHARGE

SUPPLY AIR DISCHARGE

RETURN AIR INTAKE

OUTDOOR AIR INTAKE

(NON ELECTRICAL SIDE)

OUTDOOR AIR INTAKE

RETURN AIR INTAKE

Outdoor Air Discharge End

EXHAUST AIR DISCHARGE

OUTDOOR AIR INLET

RETURN AIR INLET

SUPPLY AIR DISCHARGE

(NON ELECTRICAL SIDE)

OUTDOOR AIR INTAKE

RETURN AIR INTAKE

Top and Bottom ConnectionsTop and End Connections

EXHAUST AIR DISCHARGE

SUPPLY AIR DISCHARGE

(NON ELECTRICAL SIDE)

OUTDOOR AIR INTAKE

RETURN AIR INTAKE

Intake and Discharge Options

Bottom Top Side End

OA Intake X X

SA Discharge X X

RA Intake X X

EA Discharge X X

End Connections

Dimensional Data and Weights

Unit Size

ECV-10 54.8 28.9 43.9 18.4 x 15.9 13.6 x 13.6 8.5 x 11.6 10.25 x 15.25 485

ECV-20 65 43.9 56.9 31.2 x 19.2 13.6 x 13.6 8.6 x 11.8 15.8 x 27.8 816

ECV-30 69 61.4 60.7 43.2 x 18.2 20 x 20 16 x 13.8 40.9 x 15.9 1286

All dimensions are in inches. *Weight assumes outdoor unit with filters, weatherhoods, outdoor air intake damper, controls and internal double-wall sheet metal.

Exterior Dimensions Unit Connection Dimensions

AB C D E F G

Approx. Weight*

(lbs.)

Energy Core Ventilator4

Page 5

Service Clearances

The ECV unit requires minimum clearances to perform routine maintenance, such as ﬁlter replacement and energy core inspection. Blower and motor assemblies, energy recovery core and ﬁlter sections are always provided with a service door or panel for proper component access. Clearances for component removal may be greater than the

service clearances, refer to drawing below for these dimensions.

*NO END CLEARANCE ON UNITS WITHOUT WEATHER HOODS.

Model A (in.) ECV-10 42 ECV-20 42 ECV-30 30

CLEARANCE

WITH

BOLTED DOOR

ACCESS

24"

ACCESS DOOR

CORE REMOVAL

ACCESS DOOR

36"

HINGED ACCESS

CLEARANCE

WITH

OUTDOOR

AIR HOOD

CLEARANCE

WITH

BOLTED DOOR

ACCESS

24"

CORE

ELECTRICAL

CORE REMOVAL

ACCESS DOOR

EXHAUST AIR HOOD

*24"

ACCESS DOOR

36"

HINGED ACCESS

CLEARANCE

WITH

Access Panel Locations

The ECV is provided with access panels on both sides of the unit. The non electrical side can be placed against a wall. Clearance to the electrical side is essential to provide access to the control center and component maintenance.

1 Control Center

Core, filters, inlet

dampers, bypass dampers, blowers

3 Blowers

Electrical Side Non Electrical Side

Energy Core Ventilator 5

Page 6

Handling

While this unit was constructed with quality and dependability in mind, damage still may occur during handling of the unit for installation.

The system design and installation should follow accepted industry practice, such as described in the ASHRAE Handbook. Adequate space should be left around the unit for ﬁlter replacement and maintenance. Sufﬁcient space should be provided on the side of the unit for routine service and component removal should that become necessary.

Lifting

WARNING

All factory provided lifting lugs must be used when lifting the unit. Failure to comply with this safety precaution could result in property damage, serious injury or death.

1. Before lifting, be sure that all shipping material has been removed from unit.

2. To assist in determining rigging requirements, weights are shown under the Dimensional Data and Weights section.

3. Unit must be lifted by all lifting lugs provided on base structure.

4. Rigger to use suitable mating hardware to attach to unit lifting lugs.

5. Spreader bar(s) must span the unit to prevent damage to the cabinet by the lift cables.

6. Always test-lift the unit to check for proper balance and rigging before hoisting to desired location.

7. Never lift units by weatherhoods.

8. Never lift units in windy conditions.

9. Preparation of curb and roof openings should be completed prior to lifting unit to the roof.

10. Check to be sure that gasketing (supplied by others) has been applied to the curb prior to lifting the unit and setting on curb.

11. Do not use fork lifts for handling unit.

Energy Core Ventilator6

Page 7

Roof Curb Mounting

Rooftop units require curbs to be mounted ﬁrst. The duct connections must be located so they will be clear of structural members of the building.

1. Factory Supplied Roof Curbs: Roof curbs are Model GKD. The GKD ships in a knockdown kit (includes duct adapter) and requires ﬁeld assembly (by others). Assembly instructions are included.

2. Install Curb: Locate curb over roof opening and fasten in place. (Refer to Recommended Roof Openings). Check that the diagonal dimensions are within ±1/8 inch of each other and adjust as necessary. For proper unit operation, it is important that the installation be level. Shim as required to level.

3. Install Ductwork: Installation of all ducts should be done in accordance with SMACNA and AMCA guidelines. Duct adapter provided to support ducts prior to setting the unit.

4. Set the Unit: Lift unit to a point directly above the curb and duct openings. Guide unit while lowering to align with duct openings. Roof curbs ﬁt inside the unit base. Make sure the unit is properly seated on the curb and is level.

5. Fasten the Unit: Fasten the unit to the curb/ equipment support(s) using appropriate methods. The installer is responsible for determining appropriate support and fastening methods to ensure compliance with all applicable codes.

Curb Outside Dimensions and Weights

Unit Size

ECV-10 52.3 26.4 16.5 x 11.5 8.5 x 11.6 60

ECV-20 62.5 41.3 30.5 x 17.2 11 x 14 80

ECV-30 65 57.4 41 x 15.7 16 x 13.9 106

All dimensions are in inches. Weight is for 14-inch high model GKD curbs.

AB C D

Curb Weight

(lbs.)

Side of Unit

Roof Curb

Curb Cap Details for Factory-Supplied Roof Curbs

Unit Size A B C D E

ECV-10 1.9 5.3 4.3 0.8 0.4

ECV-20 1.9 5.3 4.3 0.8 0.4

ECV-30 1.9 5.3 4.3 0.8 0.4

All dimensions are in inches.

Base

1-inch Insulation

Energy Core Ventilator 7

Page 8

Ductwork Connections

POOR

Examples of poor and good fan-to-duct connections are shown. Airﬂow out of the fan should be directed straight or curve the same direction as the fan wheel rotates. Poor duct installation will result in low airﬂow and other system effects.

Recommended Discharge Duct Size and Length

Unit Size

Blower Size

(dia.-width)

ECV-10 10-6 14 x 14 35

ECV-20 10-6 14 x 14 35

ECV-30 12-8 12-12 20 x 20 50

• Recommended duct sizes are based on velocities across the cfm range of each model at approximately 800 feet per minute (FPM) at minimum airflow and up to 1600 fpm at maximum airflow. Recommended duct sizes are only intended to be a guide and may not satisfy the requirements of the project. Refer to plans for appropriate job specific duct size and/or velocity limitations.

• Straight duct lengths were calculated based on 100% effective duct length requirements as prescribed in AMCA Publication 201. Calculated values have been rounded up to nearest foot.

Length of Straight Duct

GOOD

Duct Size

(in.)

Straight Duct Length

(ft.)

Rail Mounting / Layout

• Rails designed to handle the weight of the unit should be positioned as shown on the diagram (rails by others).

• Make sure that rail positioning does not interfere with the supply air discharge opening or the exhaust air intake opening on the unit. Avoid area dimensioned “B” below.

• Rails should extend beyond the unit a minimum of 12 inches on each side.

Unit Size A B

ECV-10 4.2 11.5

ECV-20 5 15

ECV-30 2.9 13.8

All dimensions are in inches.

Energy Core Ventilator8

Page 9

Electrical Information

The unit must be electrically grounded in accordance with the current National Electrical Code, ANSI/NFPA 70. In Canada, use current CSA Standard C22.1, Canadian Electrical Code, Part 1. In addition, the installer should be aware of any local ordinances or electrical company requirements that might apply. System power wiring must be properly fused and conform to the local and national electrical codes. System power wiring is to the unit main disconnect (door interlocking disconnect switch standard on most units) or distribution block and must be compatible with the ratings on the nameplate: supply power voltage, phase, and amperage (Minimum Circuit Amps - MCA, Maximum Overcurrent Protection - MOP). All wiring beyond this point has been done by the manufacturer and cannot be modiﬁed without affecting the unit’s agency / safety certiﬁcation.

If ﬁeld installing an additional disconnect switch, it is recommended that there be at least four feet of service room between the switch and system access panels. When providing or replacing fuses in a fusible disconnect, use dual element time delay fuses and size according to the rating plate.

If power supply is desired through bottom of unit, run the wiring through the curb, cut a hole in the cabinet bottom, and wire to the disconnect switch. Seal penetration in cabinet bottom to prevent leakage.

The electric supply to the unit must meet stringent requirements for the system to operate properly. Voltage supply and voltage imbalance between phases should be within the following tolerances. If the power is not within these voltage tolerances, contact the power company prior to operating the system.

Voltage Supply: See voltage use range on the rating plate. Measure and record each supply leg voltage at all line disconnect switches. Readings must fall within the allowable range on the rating plate.

Key: V1, V2, V3 = line voltages as measured

VA (average) = (V1 + V2 + V3) / 3

VD = Line voltage (V1, V2 or V3) that deviates farthest from average (VA)

Formula: % Voltage Imbalance = [100 x (VA-VD)] / VA

WARNING

To prevent injury or death due to electrocution or contact with moving parts, lock disconnect switch open.

Most factory-supplied electrical components are prewired. To determine what electrical accessories require additional ﬁeld wiring, refer to the unit speciﬁc wiring diagram located on the inside of the unit control center access door. The low voltage control circuit is 24 VAC and control wiring should not exceed

0.75ohms.

Refer to Field Control Wiring Length/Gauge table for wire length maximums for a given wire gauge

Field Control Wiring Length/Gauge

Total Wire

Length

125 ft. 18

200 ft. 16

300 ft. 14

450 ft. 12

Control wires should not be run inside the same conduit as that carrying the supply power. Make sure that ﬁeldsupplied conduit does not interfere with access panel operation.

If wire resistance exceeds 0.75 ohms, an industrialstyle, plug-in relay should be added to the unit control center and wired in place of the remote switch (typically between terminal blocks R and G on the terminal strip (located on the 24 VAC terminal strip under the Typical Control Center Components). The relay must be rated for at least 5 amps and have a 24 VAC coil. Failure to comply with these guidelines may cause motor starters to “chatter” or not pull in which can cause contactor failures and/or motor failures.

Minimum

Wire Gauge

CAUTION

If any of the original wire as supplied with the appliance must be replaced, it must be replaced with wiring material having a temperature rating of at least 105ºC.

Energy Core Ventilator 9

Page 10

Typical Control Center Components

1. Main Disconnect (nonfusible, lockable)

2. Motor Starter – Exhaust Air Fan

3. Motor Starter – Outdoor Air Fan

4. Speed Controllers/VFDs (Supply & Exhaust)

5. 24 VAC Control Transformer

6. 24 VAC Terminal Strip

Optional Control Center Components

7. Economizer Controller

8. Dirty Filter Pressure Switches

9. BMS Controller

10. Frost Control Timer

11. Thermostat

Optional Accessory Wiring Schematics

Remote Panel

The remote panel is available with a number of different alarm lights and switches to control the unit. The remote panel ships loose and requires mounting and wiring in the ﬁeld. The remote panel is available with the following options:

• Unit on/off switch

• Unit on/off light

• 7-day time clock

• Hand/off/auto switch

• Dirty ﬁlter light

• Economizer light

• Frost control light

7-Day Timer

BLACK

TIMER

RED

(CAPPED)

BLUE

RRRG4

On/Off/Auto Switch & Indictor Light Wiring

Energy Core Ventilator10

CONTROL CENTER DOOR

Page 11

Dirty Filter Indicator

(powered by others)

Motor Potentiometer/0-10 VDC Fan Motor Control

Model ECV-10-VG (reference unit wiring diagram)

CLOSED 115-120V

OPEN 208-230/277V

RED

BLACK

ST1

WHITE

SUPPLY FAN

CLOSED 115-120V

OPEN 208-230/277V

RED

BLACK

ST2

WHITE

EXHAUST FAN

RED

MOTOR

RED

MOTOR

BLACK

2CBL-M1

BLACK

2CBL-M2

RED

2CBL-M1

RED

2CBL-M2

POT

BLACK

ORANGE

POT

BLACK

ORANGE

BLACK

(-)

0-10VDC

(+)

BLACK

(-)

0-10VDC

(+)

Energy Core Ventilator 11

Page 12

Optional Component Overview

Economizer

The energy core operation can be altered to take advantage of economizer operation (free cooling). Two control options are available:

1. Bypass damper

2. Exhaust only operation

Bypass damper: An integral bypass damper will cycle into a bypass condition allowing cool air to ﬂow past the energy recovery core rather than ﬂow through it. When outdoor air conditions are not suitable for economizer operation, the damper will remain closed. Economizer mode is initiated by temperature or enthalpy and dependent on the sensor. To eliminate unnecessary control sequences and the concern of overloading fans. Energizing the bypass damper is accomplished one of two ways:

1. The outdoor air temperature is <40ºF or >65ºF.

2. The outdoor air temperature is <40ºF or >65ºF DB or >55˚F dew point.

Exhaust only operation: This option allows for the exhaust fan to run continuously while the supply fan is off.

Frost Control

Extremely cold outdoor air temperatures can cause moisture condensation and frosting on the energy recovery core. Timed exhaust and a electric preheater are optional frost control features that will prevent/ control core frosting.

Timed exhaust frost control includes a timer as well as an adjustable thermostat (preset at 35°F) that is factory installed in the exhaust airstream. When timed exhaust frost control is initiated, the timer will turn the supply blower off. Timed exhaust uses a default timer setting that will shut down the supply fan for 5 minutes every 30minutes to allow for the exhaust air to defrost the energy core.

Electric preheat comes standard as single-stage on/off control. Preheaters are single point wired at the factory. An adjustable thermostat (preset at 35°F) is mounted in the exhaust airstream to monitor the discharge air temperature and enable the preheater if required. If the temperature falls below the set point, the electric preheater will turn on. Access to the electric preheat is through the outdoor air ﬁlter access door.

Reference Optional Start Up Components, Frost Control Test Procedure for troubleshooting.

Variable Frequency Drives (VFD)

VFDs are used to control the speed of the fan as either multi-speed or modulating control. Multi-speed VFDs reference a contact which can be made by a switch or a sensor with a satisfied set point. Modulating control references a 2-10 VDC signal to the VFD which will vary the fan speed from a minimum 50% to full 100% rpm. An optional CO

sensor is available to provide both a

set point contact or a modulating 2-10 VDC signal.

CO2 Sensor

The factory-provided sensors can be set to reference a set point for on/off operation.

On model ECV, this accessory is often used in Demand Control Ventilation (DCV) applications. The factory provided sensor can be set to reference a set point for multi-speed operation on the ECV-20 and ECV-30. The CO

sensor can also be used to output a 2-10 VDC

signal to modulate the fan speed on the ECV-10-VG, ECV-20 and ECV-30.

The CO

sensor is either shipped loose to mount in

the room space, ductwork, or is factory-mounted in the return air intake. Follow instructions supplied with sensor for installation and wiring details.

Dirty Filter Sensor

Dirty ﬁlter sensors monitor pressure drop across the outdoor air ﬁlters, exhaust air ﬁlters, or both. If the pressure drop across the ﬁlters exceeds the set point, the sensor will close a set of contacts in the unit control center. Field-wiring of a light (or other alarm) to these contacts will notify maintenance personnel when ﬁlters need to be replaced. The switch has not been set at the factory due to external system losses that will affect the switch. This switch will need minor ﬁeld adjustments after the unit has been installed with all ductwork complete. The dirty ﬁlter switch is mounted in the unit control center.

Energy Core Ventilator12

Page 13

Start-Up

DANGER

Electric shock hazard. Can cause injury or death. Before attempting to perform any service or maintenance, turn the electrical power to unit to OFF at disconnect switch(es). Unit may have multiple power supplies.

WARNING

Use caution when removing access panels or other unit components, especially while standing on a ladder or other potentially unsteady base. Access panels and unit components can be heavy and serious injury may occur. Do not operate energy core ventilator without the filters and birdscreens installed. They prevent the entry of foreign objects such as leaves, birds, etc.

CAUTION

Do not run unit during construction phase. Damage to internal components may result and void warranty.

SPECIAL TOOLS REQUIRED

• Voltage Meter (with wire probes)

• Amperage Meter

• Thermometer

• Tachometer

• Incline Manometer or Equivalent

General Start-Up Information

Every installation requires a comprehensive start-up to ensure proper operation of the unit. As part of that process, the following checklist must be completed and information recorded. Starting up the unit in accordance with this checklist will not only ensure proper operation, but will also provide valuable information to personnel performing future maintenance. Should an issue arise which requires factory assistance, this completed document will allow unit experts to provide quicker resolve. Qualiﬁed personnel should perform start-up to ensure safe and proper practices are followed.

Unit Model Number _______________________________

Unit Serial Number _______________________________

Start-Up Date _______________________________

Start-Up Personnel Name __________________________

Start-Up Company _______________________________

Phone Number _______________________________

(e.g. 04C99999 or 10111000)

(e.g. ECV-10)

Pre Start-Up Checklist – check as items are

completed.

 Disconnect and lock-out all power switches  Remove any foreign objects that are located in the

energy recovery unit.

 Check all fasteners, set-screws, and locking collars

on the fans, bearings, drives, motor bases and accessories for tightness.

 Rotate the fan wheels by hand to ensure no parts are

rubbing. If rubbing occurs, refer to Start-Up section for more information.

 Conﬁrm the EC motor voltage is correct. Reference

unit wiring diagram.

 Check the fan belt drives for proper alignment

and tension (refer to Start-Up section for more information).

 Filters can load up with dirt during building

construction. Replace any dirty pleated ﬁlters and clean the aluminum mesh ﬁlters in the intake hood (refer to Routine Maintenance section).

 Verify that non-motorized dampers open and close

properly.

 Check the tightness of all factory wiring connections.  Verify control wire gauge (refer to the Electrical

Connections section).

Start-Up Checklist

The unit will be in operational mode during start-up. Use necessary precautions to avoid injury. All data must be collected while the unit is running. In order to measure volts & amps, the control center door must be open, and the unit energized using a crescent wrench to turn the disconnect handle.

Check line voltage at unit disconnect _______ L1-L2 volts

_______ L2-L3 volts

_______ L1-L3 volts

Motor Amp Draw

• Supply Fan • Exhaust Fan _______ L1 amps ______ L1 amps

_______ L2 amps ______ L2 amps

_______ L3 amps ______ L3 amps

Fan RPM

_______ Supply Fan ______ Exhaust Fan

Correct fan rotation direction

Supply Fan Yes / No

Exhaust Fan Yes / No

Energy Core Ventilator 13

Page 14

Optional Accessories Checklist

Refer to the respective sections in this Installation, Operation and Maintenance Manual for detailed information.

Refer to wiring diagram in unit control center to determine what electrical accessories were provided.

Provided with Unit?

Frost Control Application / Operation section: Setting Factory Default

Yes No Frost Control set point 32ºF

Differential 2ºF Timer Refer to page 17

Economizer Application / Operation section:

Yes No Economizer (temperature)

Set point 65ºF

Offset 20ºF

Differential 2ºF

Yes No Economizer (enthalpy)

Set point D

Optional Accessories section: Operational

Yes No OA Dirty Filter Sensor Yes No N/A

Yes No EA Dirty Filter Sensor Yes No N/A

Yes N o CO

Yes No Remote Control Panel Yes No N/A

Sensor Yes No N/A

Variable Frequency Drives section: Operational

Yes No Blower VFDs Yes No N/A

Damper section: Operational

Yes No Outdoor Air Damper Yes No N/A

Yes No Exhaust Air Damper Yes No N/A

Energy Core Ventilator14

Page 15

Start-Up Components

Fans

The unit contains two forward curved (supply and exhaust) fans. These forward curved fans should be checked for free rotation. If any binding occurs, check for concealed damage and foreign objects in the fan housing. Be sure to check the belt drives per the start-up recommendations in the following section. (Not applicable to ECV-10. The ECV-10 has direct drive fans).

Forward Curved

Exhaust Fan

5. Place belts over sheaves. Do not pry or force belts, as this could result in damage to the cords in the belts.

6. With the fan off, adjust the belt tension by moving the motor base. (See belt tensioning procedures in the Routine Maintenance section of this manual). When in operation, the tight side of the belts should be in a straight line from sheave to sheave with a slight bow on the slack side.

CAUTION

When operating conditions of the fan are to be changed (speed, pressure, temperature, etc.), consult Greenheck to determine if the unit can operate safely at the new conditions.

Fan Performance Modiﬁcations

Due to job speciﬁcation revisions, it may be necessary to adjust or change the sheave or pulley to obtain the desired airﬂow at the time of installation. Start-up technician must check blower amperage to ensure that the amperage listed on the motor nameplate is not exceeded. Amperage to be tested with access doors closed and ductwork installed.

Fan Belt Drives

The fan belt drive components, when supplied by Greenheck, have been carefully selected for the unit’s speciﬁc operating condition. Utilizing different components than those supplied could result in unsafe operating conditions which may cause personal injury or failure of the following components:

• Fan Shaft • Bearings • Motor

• Fan Wheel • Belt

Tighten all fasteners and set screws securely and realign drive pulleys after adjustment. Check pulleys and belts for proper alignment to avoid unnecessary belt wear, noise, vibration and power loss. Motor and drive shafts must be parallel and pulleys in line (see diagrams in this section).

Belt Drive Installation

1. Remove the protective coating from the end of the fan shaft and assure that it is free of nicks and burrs.

2. Check fan and motor shafts for parallel and angular alignment.

3. Slide sheaves on shafts. Do not drive sheaves on as this may result in bearing damage.

4. Align fan and motor sheaves with a straight-edge or string and tighten.

WRONG WRONG

WRONG CORRECT

Direction of Fan Wheel Rotation

Blower access is labeled on unit. Check for proper wheel rotation by momentarily energizing the fan. Rotation is determined by viewing the wheel from the drive side and should match the rotation decal afﬁxed to the fan housing (see Rotation Direction ﬁgures). If the wheel is rotating the wrong way, direction can be reversed by interchanging any two of the three electrical leads.

Check for unusual noise, vibration, or overheating of bearings. Refer to the Troubleshooting section of this manual if a problem develops.

Airﬂow

Forward Curved

Fan RPM

Supply fan and exhaust fan will have an adjustable motor pulley (on 15 HP and below) preset at the factory to the customer speciﬁed RPM. Fan speed can be increased or decreased by adjusting the pitch diameter of the motor pulley. Multi-groove variable pitch pulleys must be adjusted an equal number of turns open or closed. Any increase in fan speed represents a substantial increase in load on the motor. Always check the motor amperage reading and compare it to the amperage rating shown on the motor nameplate when changing fan RPM. All access doors must be installed except the control center door. Do not operate units

with access doors open or without proper ductwork in place as the fan motors will overload.

Energy Core Ventilator 15

Page 16

Optional Start-Up Components

Economizer

Dirty Filter Switch

Setscrew (on front of switch) must be manually adjusted after the system is in operation.

Negative pressure connection is toward the ‘front or top’ of the switch. (Senses pressure on

the blower side of filters)

Positive pressure connection is toward the ‘back or bottom’ of the switch. (Senses pressure at air inlet side of filters)

To adjust the switch, the unit must be running with all of the access doors in place, except for the compartment where the switch is located (exhaust intake compartment). The adjusting screw is located on the top of the switch.

1. Open the ﬁlter compartment and place a sheet of plastic or cardboard over 50% of the ﬁlter media.

2. Replace the ﬁlter compartment door.

3. Check to see if there is power at the alert signal leads (refer to electrical diagram).

4. Whether there is power or not, turn the adjustment screw on the dirty ﬁlter gauge (clockwise if you did not have power, counterclockwise if you did have power) until the power comes on or just before the power goes off.

5. Open the ﬁlter compartment and remove the obstructing material.

6. Replace the door and check to make sure that you do not have power at the alert signal leads.

The unit is now ready for operation.

Relevant Set Points

1. MAT SET The outdoor air temperature set point after the energy core. The control will open/close the bypass damper to maintain temperature as best as it can. (Set point menu, default 53°F )

2. LOW T LOCK The set point for the low temperature mechanical cooling lockout. (Set point menu, default 32°F)

3. DRYBLB SET The outdoor air set point to call for economizer. (Set point menu, default 63°F)

4. AUX1 O The controllers operating sequence structure. (Set point menu, default ‘None’)

5. ERV OAT SP The set point for low temperature economizer lockout. This is the low temperature set point when AUX1 O is set to ERV. (Set point menu, default 40°F)

Using the Keypad with Settings and Parameters

To use the keypad when working with set points, system and advanced settings, checkout tests, and alarms:

1. Navigate to the desired menu.

2. Press currently displayed menu.

3. Use the and buttons to scroll to the desired parameter.

4. Press displayed item.

5. Press the button to increase (change) the displayed parameter value.*

6. Press the displayed parameter value.

7. Press (enter) to accept the displayed value and store it in non-volatile RAM.

8. CHANGE STORED displays.

9. Press parameter.

10. Press parameter.

When values are displayed, pressing and holding the or button causes the display to automatically increment.

(enter) to display the ﬁrst item in the

(enter) to display the value of the currently

button to increase (change) the

(enter) to return the current menu

(escape) to return to the current menu

Energy Core Ventilator16

Page 17

Frost Control Test Procedure

Timed Exhaust

1. Remove power from unit.

2. Jumper the temperature indicating sensor in the unit control center. Thermostat controller has a pre-set temperature of 35ºF.

3. Set the frost control timer scale for T1 and T2 to 5m. Set the timer settings for T1 and T2 to 30.

4. Add power to the unit. Blower should cycle on for 30 minutes, then turn off for 5 minutes.

5. Remove power from unit and remove jumpers that were placed. Reset timer settings.

• T1 timer setting set to 5 and timer scale set to

10m for 5 minutes of blower off time.

• T2 timer setting set to 5 and

timer scale set to 1h for 30 minutes of blower on time.

Electric Preheat

1. Remove power from unit.

2. Place wire jumper between terminal R and G.

3. Turn dial on the thermostat TS1

Timer Scale

Timer

Settings

Timer Scale

to highest temperature setting.

4. Apply power to unit. Preheater should turn on.

5. Remove power from unit, if applicable remove wire jumper placed between R and terminal G, and turn dial on thermostat TS1 to factory setting (35ºF).

CO2 Proportional Control

Speed Controller

A carbon dioxide sensor is provided from the factory for ﬁeld mounting OR unit mounting in the space(s) being served by the energy recovery unit.

The ECV-10-VG carbon dioxide sensor is wired to the speed controller with default factory settings for proportional control of 500 PPM or less CO speed and 1500 PPM or greater CO

= 100% fan speed.

= 50% fan

The blower’s speed proportionally modulates between 500 and 1500 PPM CO

Variable Frequency Drive

The ECV-20 and ECV-30 are wired to the Variable Frequency Drive (VFD). Refer to the Variable Frequency Drive section for control sequence and programming.

Vari-Green® Electronically Commutated (EC) Motor

Features

Soft Start – All motors feature soft-start technology which eliminates inrush current at start-up. The motors will reliably start at any speed setting.

Overload Protection – If the motor becomes overloaded, it will automatically reduce its speed until it is no longer overloaded. This means that the motor will never operate in the “service factor” which is possible with many AC motors.

Locked Rotor Protection – If the motor ever encounters a locked-rotor scenario, the motor will automatically shut itself down. It will try to restart up to 3 times and if after the 3rd time the motor will still not rotate, the motor will not attempt to start again until power is cycled.

Thermal Protection – The motors will have an internal thermal protection which electronically regulates the RPM limit until an acceptable temperature is met.

Operation and Wiring

These motors have the ability to accept a plug in potentiometer for speed adjustment AND the ability to accept a 0-10V signal for remote control.

Motor Potentiometer - Turn the dial with your ﬁngers to adjust. To increase the speed, rotate the dial clockwise. To decrease the speed, rotate the dial counterclockwise. Turning the dial full counterclockwise will turn the motor off.

0-10 VDC Signal - From 0-1.9V, the motor will be off and will operate within the 2-10V range. This motor does not require 24V power for operation.

Energy Core Ventilator 17

Page 18

Variable Frequency Drives

Optional factory installed, wired, and programmed variable frequency drives (VFDs) may have been provided for modulating or multi-speed control of the blowers. One VFD, either Yaskawa model V1000 or J1000, is provided for each blower (supply air and exhaust).

Refer to the tables in this section for factory settings and field wiring requirements. Refer to the unit control center for unit specific wiring diagram. When making adjustments outside of the factory set points, refer to Yaskawa VFD instruction manual, which can be found online at www.drives.com. For technical support, contact Yaskawa direct at 1-800-927-5292.

IGS-S+R-R+

MPACAMAC+VA2A1PCP2P1

MA MB MCRPH1SCHCS7S6S5S4S3S2S1

J1000

V1000

OPTION 1 - 0-10 VDC CONTROL

USER TO PROVIDE ISOLATION AS REQUIRED

A1 AC

SEE VFD INSTALLATION MANUAL FOR MORE DETAIL

FOR CONTINUOUS 60Hz OPERATION JUMPER TERMINALS A1 AND +V.

USER TO PROVIDE CONTACTS AND ISOLATION AS REQUIRED

SEE VFD INSTALLATION MANUAL FOR MORE DETAIL

0-10 VDC CONTROL SIGNAL (BY OTHERS) WIRED TO A1 (+) AND AC (COMMON) 0 VDC = 30 Hz 10 VDC = 60 Hz

FOR ONE 0-10 SIGNAL, WIRE TO DRIVES IN PARALLEL

OPTION 2 - MULTI SPEED CONTROL

S5S4 SC

NEITHER S4 OR S5 CONTACT CLOSED DRIVE SPEED = 60 Hz.

S4 TO SC CONTACT CLOSED (BY OTHERS) DRIVE SPEED = 40 Hz.

S5 TO SC CONTACT CLOSED (BY OTHERS) DRIVE SPEED = 30 Hz.

MA MB MCACAMAC+VA1SCS5S4S3S2S1

Factory Set Points

Variable frequency drives (VFDs) for the blowers are factory setup to operate in one of the three following modes:

• Modulating: 0-10 VDC signal wired in the ﬁeld by others varies the speed of the blower between 30 and 60 Hz

• Multi-speed: Digital contact closures by others command the VFD to run at multiple speed settings: ż Open - Drive runs at 60 Hz

ż SC to S4 - Drive runs at 40 Hz ż SC to S5 - Drive runs at 30 Hz

• CO

Sensor:

ż Set Point Control: A carbon dioxide sensor is

provided from the factory for ﬁeld mounting OR unit mounting in the space(s) being served by the energy recovery unit. The CO

sensors are wired

to the unit VFD’s with two preset speeds of 700 PPM or less CO2 = 50% fan speed and 800 PPM or greater CO

= 100% fan speed.

ż Proportional Control: A carbon dioxide sensor

is provided from the factory for ﬁeld mounting OR unit mounting in the space(s) being served by the energy recovery unit. The CO

sensors are wired

to the unit VFD’s with default factory settings of 500 PPM or less CO2 = 50% fan speed and 1000 PPM or greater CO2 = 100% fan speed. Modulation of VFD occurs proportional to CO

between 500 and 1000PPM.

The terminal locations for modulating and multi-speed are shown on the previous page. Most of the set points in the VFDs are Yaskawa factory defaults. However, a few set points are changed at Greenheck and are shown in the tables. These settings are based on the VFD mode selected.

Change Set Points

To gain access to change set points on the V1000 and J1000 drives, parameter A1-01 needs to be set at “2”. To prevent access or tampering with drive settings on either drive, change parameter A1-01 to “0”.

• Drive Operation

ż SC to S1 contact for On/Off

ż A1 (0-10 VDC) referenced to AC.

Can use +15 VDC from +V.

Resetting the V1000 drive to factory defaults

To reset the V1000 drive back to Greenheck factory defaults, go to parameter A1-01 and set it to “2”. Then go to A1-03 and change it to “1110” and press enter. The drive is now reset to the settings programmed at Greenheck. This option is not available on the J1000.

Energy Core Ventilator18

Page 19

MODULATING CONTROL FOR FAN SPEED

(0-10 VDC)

Parameter

Setting

V1000 J1000

A1-01 Access Level 2 2 B1-17 VFD Start-Up Setting 1 1 C6-02 Carrier Frequency 1 1 D2-02 Ref Lower Limit 50% 50%

E2-01 Motor Rated FLA

Motor

FLA

Motor

FLA H2-01 Terminal MA, MC Function 5 5 H3-04 Terminal A1 Bias 50% 50%

L4-01 H2-01 Frequency Detection 15 15 L5-01 Auto Restart Attempt 5 5 A1-01 Access Level 0 0

CO2 SENSOR CONTROL FOR FAN SPEED

(1/2 SPEED WHEN CO2 DROPS BELOW 700 PPM)

(FULL SPEED WHEN CO2 RISES ABOVE 800 PPM)

MULTI-SPEED CONTROL FOR FAN SPEED

(1/3 OR 1/2 SPEED REDUCTION)

Parameter

Setting

V1000 J1000

A1-01 Access Level 2 2

B1-01

Reference Source

(Frequency)

B1-17 VFD Start-Up Setting 1 1 C6-02 Carrier Frequency 1 1 D1-01 Frequency Reference 1 60 Hz 60 Hz D1-02 Frequency Reference 2 40 Hz 40 Hz D1-03 Frequency Reference 3 30 Hz 30 Hz D1-04 Frequency Reference 4 60 Hz 60 Hz D2-02 Ref Lower Limit 50% 50%

E2-01 Motor Rated FLA

H1-04

H1-05

H1-06

Multi-Function Input Sel 4

(Terminal S4)

Multi-Function Input Sel 5

(Terminal S5)

Multi-Function Input Sel 6

(Terminal S6)

Motor

FLA

Motor

FLA

5NA

H2-01 Terminal MA, MC Function 5 5 H3-10 A2 Not Used F NA

L4-01 H2-01 Frequency Detection 15 15 L5-01 Auto Restart Attempt 5 5 A1-01 Access Level 0 0

CO2 PROPORTIONAL CONTROL

Parameter

Setting

V1000 J1000

B1-17 VFD Start-Up Setting 1 1

C6-02 Carrier Frequency 1 1

D2-02 Ref Lower Limit 50% 50% E2-01 Motor Rated FLA FLA FLA

H3-03

H3-04

Analog Frequency

Reference (Gain)

Analog Frequency

Reference (Bias)

150% 150%

25% 25%

L2-01 Ride Thru Power Loss 2 2 L4-05 Frequency Ref Loss 0 NA

L5-01 Auto Restart Attempt 5 5

A1-01 Access Level 0 0

Energy Core Ventilator 19

Page 20

Routine Maintenance

DANGER

CAUTION

Once the unit has been put into operation, a routine maintenance program should be set up to preserve reliability and performance. Items to be included in this program are:

Lubrication

Apply lubrication where required

Dampers

Check for unobstructed operation

Fan Belts

Check for wear, tension, alignment

Motors

Check for cleanliness

Blower Wheel & Fasteners

Check for cleanliness Check all fasteners for tightness Check for fatigue, corrosion, wear

Bearings

Check for cleanliness Check set screws for tightness Lubricate as required

External Filter

Check for cleanliness - clean if required

Internal Filter

Check for cleanliness - replace if required

Door Seal

Check if intact and pliable

Maintenance Procedures:

Lubrication

Check all moving components for proper lubrication. Apply lubrication where required. Any components showing excessive wear should be replaced to maintain the integrity of the unit and ensure proper operation.

Dampers

Check all dampers to ensure they open and close properly and without binding. Backdraft dampers can be checked by hand to determine if blades open and close freely. Apply power to motorized dampers to ensure the actuator opens and closes the damper as designed.

Fan Belts

Belts must be checked on a regular basis for wear, tension, alignment, and dirt accumulation. Premature or frequent belt failures can be caused by improper belt tension (either too loose or too tight) or misaligned sheaves. Abnormally high belt tension or drive misalignment will cause excessive bearing loads and may result in failure of the fan and/or motor bearings. Conversely, loose belts will cause squealing on start-up, excessive belt ﬂutter, slippage, and overheated sheaves. Both loose and tight belts can cause fan vibration.

When replacing belts on multiple groove drives, all belts should be changed to provide uniform drive loading. Do not pry belts on or off the sheave. Loosen belt tension until belts can be removed by simply lifting the belts off the sheaves. After replacing belts, insure that slack in each belt is on the same side of the drive. Belt dressing should never be used.

Do not install new belts on worn sheaves. If the sheaves have grooves worn in them, they must be replaced before new belts are installed.

The proper belt setting is the lowest tension at which the belts will not slip under peak load operation. For initial tensioning, set the belt deflection at 1/64-inch for each inch of belt span (measured half-way between sheave centers). For example, if the belt span is 64inches, the belt deflection should be oneinch (using moderate thumb pressure at mid-point

Deflection =

Belt Span

of the drive). Check belt tension two times during the first 24hours of operation and periodically thereafter.

Belt Span

Fan Motors

Motor maintenance is generally limited to cleaning and lubrication. Cleaning should be limited to exterior surfaces only. Removing dust and grease buildup on the motor housing assists proper motor cooling. Never wash-down motor with high pressure spray. Greasing of motors is only intended when ﬁttings are provided. Many fractional motors are permanently lubricated for life and require no further lubrication.

Energy Core Ventilator20

Page 21

Fan Wheel & Fasteners

Wheels require very little attention when moving clean air. Occasionally oil and dust may accumulate on the wheel causing imbalance. When this occurs the wheel and housing should be cleaned to assure smooth and safe operation. Inspect fan impeller and housing for fatigue, corrosion or wear.

Routinely check all fasteners, set screws and locking collars on the fan, bearings, drive, motor base and accessories for tightness. A proper maintenance program will help preserve the performance and reliability designed into the fan.

Bearings

Most bearings are permanently lubricated and require no further lubrication under normal use. Normal use being considered -20ºF to 120ºF and in a relatively clean environment. Some bearings are relubricatable and will need to be regreased depending on fan use. Check your bearings for grease zerk ﬁttings to ﬁnd out what type of bearing you have. If your fan is not being operated under normal use, bearings should be checked monthly for lubrication.

External Filter Maintenance

Aluminum mesh, 2-inch deep ﬁlters are located in the supply weatherhood (if the weatherhood option was ordered). Filters should be checked and cleaned on a regular basis for best efﬁciency. The frequency of cleaning depends upon the cleanliness of the incoming air. These ﬁlters should be cleaned prior to start-up. Clean ﬁlters by rinsing with a mild detergent in warm water.

Internal Filter Maintenance

The units will typically be provided with 2-inch, pleated ﬁlters in the outdoor air and exhaust airstreams. These ﬁlters should be checked per a routine maintenance schedule and replaced as necessary to ensure proper airﬂow through the unit. See table for pleated ﬁlter size and quantity for each unit. Replacement ﬁlters shall be of same performance and quality as factory installed ﬁlters. Filter type must be pleated design with integral metal grid. Two acceptable ﬁlter replacements are Aerostar Series 400 or Farr 30/30

Outdoor Air Filters: Access to the outdoor air ﬁlters is through the door labeled as “Filter Access” on the sides of the unit.

Exhaust Air Filters: Access to the exhaust air ﬁlters is through the door labeled as “Filter Access” on the sides of the unit.

Refer to Access Panel Location section for additional information on ﬁlter locations.

Door Seal Maintenance

A bulb seal is installed on the perimeter of the door frame. Inspect at least annually to ensure that the seal is still intact.

Energy Recovery Core

Annual inspection of the energy recovery core is recommended. Units ventilating smoking lounges and other nonclean air spaces should have energy recovery core inspections more often based upon needs.

Accessing the energy recovery core - Disconnect the power to the ECV. Remove access panel.

Removing the energy recovery core - Once the energy core access doors are removed, the core can be pulled from the housing. To replace the core, reverse the procedure.

Recommended cleaning procedure - First, remove the energy recovery core by following the instructions on this page.

Once the core is removed, gently vacuum the surfaces of the core to remove the dirt and debris that has accumulated.

Frequency of cleaning - A regular cleaning cycle must be established for the energy recovery core in order to maintain optimum sensible and latent energy transfer. In reasonably clean environments such as schools, ofﬁces or retail stores, the energy recovery core should be inspected annually and cleaned as needed.

Failure to follow a regular cleaning cycle for the energy recovery core can result in signiﬁcant energy transfer performance losses.

WARNING

Do not wash, soak in water or use detergents and cleaners on the core. This will result in a damaged core.

Pleated Filter Size and Quantities

Unit Size

ECV-10 16 x 20 2 20 x 20 2

ECV-20 16 x 20 2 20 x 20 2

ECV-30 20 x 20 3 20 x 20 3

All dimensions in inches.

Supply Exhaust

Size Qty Size Qty

Energy Core Ventilator 21

Page 22

Troubleshooting - Economizer Alarms

Addressing Alarms

Alarms will signify a faulty sensor. When this occurs, verify all connections to the sensor and controller are secure. Press enter twice to clear the alarm. If the issue persists, consult the factory.

Clearing Alarms

Once the alarm has been identiﬁed and the cause has been removed (e.g. replaced faulty sensor), the alarm can be cleared from the display.

To clear an alarm, perform the following:

1. Navigate to the desired alarm.

2. Press the

3. ERASE? displays.

4. Press (enter).

5. ALARM ERASED displays.

6. Press to the previous menu.

If an alarm still exists after you clear it, it redisplays within 5 seconds.

(enter).

(escape) to complete the action and return

NOTE

Energy Core Ventilator22

Page 23

Troubleshooting – Airﬂow

Test and Balance Report

The Test and Balance Report (TAB) is utilized to determine whether the appropriate amount of outdoor air and exhaust air is being supplied and removed from a building, respectively. There are no set rules on what information must be included in a TAB report. As such, if a TAB report indicates that the airflow on a unit is low, prior to contacting the factory, please determine the following information:

Unit #1 Unit #2 Unit #3 Unit #4

Model Number

Serial Number

Nameplate Information

Voltage

Hertz

Phase

Outdoor Air Fan Amps

Exhaust Fan Amps

Outdoor Air Fan Horsepower

Exhaust Fan Horsepower

Design Airflow

Outdoor Air

Exhaust

Measured Airflow

Outdoor Air

Exhaust

Measured Data

Blower Rotation

Outdoor Air Fan RPM

Exhaust Fan RPM

Outdoor Air Fan Amp Draw

Exhaust Fan Amp Draw

Airflow problems can often be tied back to improper ductwork installation. Be sure to install ductwork in accordance with SMACNA and AMCA guidelines.

Energy Core Ventilator 23

Page 24

Troubleshooting – Unit

Symptom Possible Cause Corrective Action

Replace fuse or reset circuit breaker and check amps.

Check for On/Off switches. Check for correct supply voltage.

Check for broken or loose belts. Tighten loose pulleys.

Shorten wiring run to mechanical room or install a relay which will turn unit on/off. Consult factory for relay information.

Need to increase supply power or use a special control transformer which is sized for the actual supply power.

If higher, ductwork should be improved. If lower, fan rpm should be lower.

See speciﬁcations and catalog for fan curves to determine if horsepower is sufﬁcient.

Improve ductwork to eliminate losses using good duct practices.

For 3-phase, see Direction of Fan Wheel Rotation under Unit Start-Up section.

Follow cleaning procedures in Routine Maintenance section.

Correct or improve ductwork.

Check for correct fan rpm. Decrease fan speed if necessary.

Induce Ps into system ductwork. Make sure grilles and access doors are installed. Decrease fan speed if necessary.

Adjust frost temperature sensor set point as needed.

Blower fails to operate

Motor starters “chatter” or do not pull in

Motor over amps

Low airﬂow (cfm)

High airﬂow (cfm)

One or both blowers turn off intermittently and back on after about 2 minutes

Blown fuse or open circuit breaker.

Defective motor or capacitor. Replace.

Motor starter overloaded. Reset starter and check amps.

Electrical.

Drive.

Control power (24 VAC) wiring run is too long (resistance should not exceed 0.75 ohms).

Incoming supply power is less than anticipated. Voltage supplied to starter coil must be within +10% / -15% of nominal voltage stated on the coil.

CFM too high. Check cfm and adjust drives if needed.

Static pressures are higher or lower than design.

Blower rotation is incorrect. Check rotation and reverse if necessary.

Motor voltage incorrect. Check motor nameplate versus supplied voltage.

Motor horsepower too low.

Shorted windings in motor. Replace motor.

Unit damper not fully open. Adjust damper linkage or replace damper motor.

System static pressure too high.

Blower speed too low. Check for correct drives and rpm with catalog data.

Fan wheels are operating backwards.

Dirty ﬁlter or energy core.

Leaks in ductwork. Repair.

Elbows or other obstructions may be obstructing fan outlet.

Belt slippage. Adjust belt tension.

Blower fan speed too high.

Filter(s) not in place. Install ﬁlters.

Insufﬁcient static pressure (Ps) (airﬂow resistance).

Frost control sensors are tripping.

Always have a completed Pre Start-Up Checklist, unit Start-Up Checklist, and Optional Accessories Checklist prior to requesting parts or service information.

Energy Core Ventilator24

Page 25

Troubleshooting – Unit

Symptom Possible Cause Corrective Action

Adjust wheel and/or inlet cone. Tighten wheel hub or bearing collars on shaft.

Replace defective bearing(s). Lubricate bearings. Tighten collars and fasteners.

Excessive noise

Fan wheel rubbing on inlet.

Bearings.

Motor base or blower loose. Tighten mounting bolts.

or vibration

Bearing and drive misaligned. Realign.

Make sure ductwork is supported properly. Make

Noise being transmitted by duct.

sure ductwork metal thickness is sized for proper stiffness. Check duct size at discharge to ensure that air velocities are not too high.

Always have a completed Pre Start-Up Checklist, unit Start-Up Checklist, and Optional Accessories Checklist prior to requesting parts or service information.

Energy Core Ventilator 25

Page 26

Maintenance Log

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Energy Core Ventilator26

Page 27

Maintenance Log

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Date ___________________Time _____________ AM/PM

Notes: ___________________________________________

_________________________________________________

Energy Core Ventilator 27

Page 28

Our Commitment

As a result of our commitment to continuous improvement, Greenheck reserves the right to change speciﬁcations without notice.

Product warranties can be found online at Greenheck.com, either on the speciﬁc product page or in the literature section of the website at Greenheck.com/Resources/Library/Literature.

Greenheck catalog, Energy Core Ventilators, Model MiniCore and ECV, provides additional information describing the equipment, fan performance, available accessories, and speciﬁcation data.

Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: gfcinfo@greenheck.com • Website: www.greenheck.com

AMCA Publication 410-96, Safety Practices for Users and Installers of Industrial and Commercial Fans, provides additional safety information. This publication can be obtained from AMCA International, Inc. at www.amca.org.