Page 1
R7824, R7847, R7848, R7849,
R7861, R7886 Amplifiers for
7800 SERIES Relay Modules
APPLICATION
The R7824C Rectification Flame Amplifier is a solid state
plug-in amplifier that responds to a rectified signal from a
C7024E,F Self-Check Ultraviolet Flame Detector to indicate
the presence of flame when used with an RM7824 Relay
Module.
PRODUCT DATA
FEATURES
• Flame failure response time of 0.8 or 1 second; or 2.0 or
3.0 seconds, depending on the amplifier and relay
module selected. See Table 1.
• Plug-in to 7800 SERIES Relay Module through printed
circuit board edge connector keyed for proper
orientation.
• Flame signal test jacks measure amplifier flame signal
voltage.
• 0.0 to 5.0 Vdc Flame signal strength reading rang e.
• Color coded label identifies flame detection type:
Green—rectification. Red—infrared.
Purple—ultraviolet. Blue—pulsed rectification.
• R7847B, R7848B, R7849B Dynamic Ampli-Check®
circuitry tests all flame amplifier components 12 times
per minute. The 7800 SERIES Relay Module locks out on
safety shutdown with amplifier failure.
• R7824C and R7847C Dynamic Self-Check Rectification
Amplifier, R7861 Self-Check Ultraviolet Flame Amplifier
and R7886A Dynamic Self-Check Ultraviolet Amplifier
test the detectors and all electronic components in the
flame detection system 12 times per minute. The 7800
SERIES Relay Module locks out on safety shutdown
with flame detection system failure.
NOTE: R7824C, Series 2 or greater, and R7847C,
Series 4 or greater, pulse shutter when signal of
1.5 Vac is sensed.
The R7847A,B Rectification Flame Amplifiers are solid state
plug-in amplifiers that respond to a rectified signal from a
rectification type flame detector to indicate the presence of
flame when used with 7800 SERIES Relay Modules.
The R7847C Self-Check Rectification Flame Amplifier is a
solid state plug-in amplifier that responds to a rectified signal
from a C7012E,F Self-Check Ultraviolet Flame Detector to
indicate the presence of flame when used with 7800 SERIES
Relay Modules. This is not European Community (CE)
approved for EC7810, EC7820, EC/RM7830 or EC/RM7850
Relay Modules.
The R7848A,B Infrared Flame Amplifiers are solid state plugin amplifiers that respond to an infrared signal from a C7015
Infrared Flame Detector to indicate the presence of flame
when used with 7800 SERIES Relay Modules.
The R7849A,B Ultraviolet Flame Amplifiers are solid state
plug-in amplifiers that respond to an ultraviolet signal from a
C7027, C7035 or C7044 Ultraviolet Flame Detector to
indicate the presence of flame when used with 7800 SERIES
Relay Modules.
® U.S. Registered Trademark
Copyright © 1998 Honeywell Inc. • All Rights Reserved
The R7861A Self-Check Ultraviolet Flame Amplifier is a solid
state plug-in amplifier that responds to an ultraviolet signal
from a C7061 Self-Check Ultraviolet Flame Detector to
indicate the presence of flame when used with 7800 SERIES
Relay Modules.
The R7886A Dynamic Self-Check Ultraviolet Amplifier is a
solid state plug-in amplifier that responds to a pulsed direct
current signal from a C7076A,C Ultraviolet Flame Detector
with adjustable sensitivity to indicate the presence of flame
when used with 7800 SERIES Relay Modules.
Contents
Application............................................................................. 1
Features ................................................................................ 1
Specifications ........................................................................ 2
Ordering Information ............................................................. 2
Installation ............................................................................. 4
Checkout ............................................................................... 6
65-0109-6
Page 2
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
SPECIFICA TIONS
Models:
Flame Detection Systems (see Table 2):
Rectification:
R7824C for use with C7024E,F Solid State Ultra violet
Detectors.
R7847A for use with flame rods, rectifying photocells or
C7012A,C Solid State Ultraviolet Detectors .
R7847B for use with flame rods, rectifying photocells or
C7012A,C Solid State Ultraviolet Detectors .
R7847C for use with C7012E,F Solid State
Ultraviolet Detectors.
Infrared:
R7848A for use with C7015 Infrared (lead sulfide) Detector .
R7848B for use with C7015 Infrared (lead sulfide) Detector .
Ultraviolet:
R7849A for use with C7027/C7035/C7044 Minipeeper
Ultraviolet Detectors.
R7849B for use with C7027/C7035/C7044 Minipeeper
Ultraviolet Detectors.
R7861A for use with C7061A Ultraviolet Detector .
R7886A for use with C7076A,D Ultraviolet Detectors with
adjustable sensitivity .
Flame Failure Response Time :
See T able 1.
Table 1. Relay Module Flame Failure Response Time (FFRT).
Flame Failure Response
Time (FFRT)
Relay Module
EC7810, EC7820,
EC/RM7830, EC/RM7850
RM/EC7823, RM/EC7885,
RM/EC7890, RM/EC7895,
RM7896, RM7888, RM7838,
RM7800, RM7840
RM7824 N/A 3.0
0.8 or 1.0
seconds
1.0 2.0
0.8 3.0
2.0 or 3.0
seconds
Envir onmental Ratings:
Ambient T emper ature:
Operating: -40 °F to 140°F (-40°C to 60°C).
Storage: -40°F to 150°F (-40°C to 65°C).
Humidity: Oper ating 85% rh continuous, noncondensing.
Vibration: Contin uous 0.5G environment.
Dimensions:
See Fig. 1.
S
3-9/16 (91)
–+
FLAME AMPLIFIER
3
(76)
3/8 (9)
7/8
(23)
M11460
Fig. 1. Flame amplifier dimensions in in. (mm).
Weight:
2.5 oz (71g), unpacked.
Approvals:
Underwriters Laboratories Inc. Listed: File no. MP268, Guide no.
MCCZZ: R7847A, R7847B , R7847C , R7861A, R7886A,
R7848A, R7848B, R7849A, R7849B.
Underwriters Laboratories Inc. Component Recognized: File no.
MP268, Guide no. MCCZZ: R7824C.
Canadian Standards Association Certified: LR95329-3.
Factory Mutual Approv ed: Report J.I.1V9A0.AF.
Industrial Risk Insurers: Acceptable .
NO T E : EN298 Approved: When these amplifiers are used
with an EC7810, EC7820, EC/RM7830, or
EC/RM7850 Relay Module.
Flame Signal (V olts dc):
Minimum Acceptable: 1.25 Vdc.
Flame Signal Voltage Range (displayed on K e yboard Display
Module or measured with a 1M ohm/volt meter plugged into
amplifier test jacks): 0.0 to 5.0 Vdc.
Accessories:
Flame Simulators:
Rectification: 123514A.
Ultraviolet: 203659.
Flame Detectors (ordered separately): select from Tab le 2.
ORDERING INFORMATION
When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the
TRADELINE® Catalog or price sheets for complete ordering number.
If you have additional questions, need further information, or would like to comment on our products or services, please write or
phone:
1. Your local Home and Building Control Sales Office (check white pages of your phone directory).
2. Home and Building Control Customer Logistics
Honeywell Inc., 1885 Douglas Drive North
Minneapolis, Minnesota 55422-4386 (612) 951-1000
In Canada—Honeywell Limited/Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 3N7.
International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,
Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.
65-0109—6 2
Page 3
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
Table 2. Flame Detection Systems.
Plug-in Flame Signal Amplifiers Applicable Flame Detectors
Flame Failure
Type Color Self-Checking Model
Rectification Green Dymanic Self-
R7824C
b,c, i
Time (sec)
Check
Response
No
No
No
Dynamic
R7847A
R7847A
R7847A
R7847B
h
h
h
e,h
0.8/1 or 2/3 Gas Rectifying
0.8/1 or 2/3 Oil Rectifying
0.8/1 or 2/3 Gas Rectifying
Ampli-Check®
Dynamic
R7847B
e,h
0.8/1 or 2/3 Oil Rectifying
Ampli-Check®
Dynamic
R7847B
e,h
Ampli-Check®
Dynamic
R7847C
c,f, i
Self-Check
Infrared Red No R7848A 2/3 Gas, oil,
Dynamic
R7848B
e
3 sec Gas, oil,
Ampli-Check®
Ultraviolet Purple No R7849A 0.8/1 or2/3 Gas, oil Ultraviolet
Dynamic
R7849B
d
0.8/1 or 2/3 Gas, oil Ultraviolet
Ampli-Check®
Dynamic
R7861A
c,f
0.8/1 or 2/3 Gas, oil,
Self-Check
,f
Blue Dynamic
R7886A
c
Self-Check
a
Flame Failure Response Time (FFRT) depends on selection of amplifier and 7800 SERIES Relay Module.
b
R7824C is used only with the 24 Vdc RM7824 Relay Module and C7024E,F Flame Detectors.
c
Circuitry tests all electronic components in flame detection system (amplifier and detector) 12 times a minute during burner
operation and shuts down burner if detection system fails.
d
Use only Honeywell part no. 38316 Photocell.
e
Circuitry tests flame signal amplifier 12 times a minute during burner operation and shuts down burner if amplifier fails.
f
200/220/240 Vac applications require a 120 Vac, 10 VA minimum stepdown transformer (not provided) to drive the shutter.
Applies to R7847C series 3 or greater; R7886A series 2 or greater; R7861 series 1 or greater. Fig. 2 shows flame detector
wiring.
g
Use C7027, C7035 and C7044 Flame Detectors only on burners that cycle on-off at least once every twenty-four hours. Use
C7012E,F Flame Detector with R7847C Amplifier, C7061A Ultraviolet Detector with R7861A Amplifier or C7076A Flame
Detector with R7886A Amplifier as ultraviolet flame detection system for appliances with burners that remain on continuously
for twenty-four hours or longer.
h
R7847A,B Amplifiers with 0.8/1 second FFRT should not be used with C7012A,C Solid State Ultraviolet Detectors.
i
R7824C Series 2 and greater and R7847C Series 4 and greater check flame detector system when flame reaches 1.5 Vdc or
at 4.5 seconds, whichever occurs first.
j
Order flame rod separately; see flame detector Instructions for holder.
a
Fuel Type Models
3 Gas, oil,
coal
2/3 Gas, oil,
coal
2/3 Gas, oil,
coal
2/3 Gas, oil,
coal
coal
coal
coal
2/3 Gas, oil,
coal
Ultraviolet
C7024E,F
(Purple
Peeper®)
C7004, C7007,
Flame Rod
Holders
j
C7011 Complete
Assemblies: C7008,
C7009, Q179
C7003, C7010,
Photocell
Ultraviolet
C7013, C7014
C7012A,C.
(Purple
Peeper®)
C7004, C7007,
Flame Rod
Holders
b
C7011 Complete
Assemblies: C7008,
C7009, Q179
C7003, C7010,
Photocell
Ultraviolet
C7013, C7014
C7012A,C
(Purple
Peeper®)
Ultraviolet
C7012E,F
(Purple
Peeper®)
Infrared (Lead
C7015
Sulfide)
Infrared (Lead
C7015
Sulfide)
C7027, C7035,
(Minipeeper)
C7044
C7027, C7035,
(Minipeeper)
C7044
Ultraviolet C7061
Ultraviolet
C7076
(Adjustable
Sensitivity)
d
d
g
g
65-0109—63
Page 4
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
1. Align the amplifier circuit board edge connector with the
CAUTION
Equipment Damage Hazard.
Incorrect combination of relay module, amplifier
and flame detector can cause equipment damage.
In infrared applications (C7015 Infrared Flame
Detector and R7848 Amplifier) using the RM7890
Relay Module with software revision 4004 or less
requires a ten-second delay to start sequence. This
applies only to the initial powering of the RM7890.
keyed receptacle on the 7800 SERIES Relay Module.
Be sure the amplifier nameplate faces away from the
Relay Module.
2. Push in the amplifier until the circuit board is fully
inserted into the receptacle and then push the amplifier
toward the 7800 SERIES Rela y Module retaining clasp.
3. Be sure the amplifier is firmly in place.
4. Perform all required check out tests.
Installing Flame Detector
INSTALLATION
When Installing this Product…
1. Read these instructions carefully. Failure to follow them
could damage the product or cause a hazardous
condition.
2. Check the ratings given in the instructions and on the
product to make sure the product is suitable for your
application.
3. Installer must be a trained, experienced, flame
safeguard control technician.
4. After installation is complete, check out the product
operation as provided in these instructions.
WARNING
Electric Shock Hazard.
Can cause electrical shock,
serious injury or death.
Disconnect the power supply before beginning
installation. More than one power supply
disconnection can be involved.
IMPORTANT
1. Wiring must comply with all applicable codes,
ordinances and regulations.
2. Wiring (where required) must comply with NEC
Class 1 (Line Voltage) wiring.
3. Perform all required checkout tests after
installation is complete.
NOTE: Table 2 lists flame detection systems available for
use with 7800 SERIES Relay Modules. Be sure to
use the correct combination of amplifier and flame
detector.
Proper flame detector installation is the basis of a safe and
reliable flame safeguard installation. Refer to the Instructions
packed with the flame detector and the equipment manufacturer instructions.
Keep the flame signal leadwires as short as possible from the
flame detector to the wiring subbase. Capacitance increases
with leadwire length, reducing the signal strength. The
maximum permissible leadwire length depends on the type of
flame detector, leadwire and conduit. However, the ultimate
limiting factor for the flame detector leadwire is the flame
signal; see Table 3 in the Checkout section.
CA UTION
Equipment Damage Hazard.
Can cause equipment damage.
Disconnect 7800 SERIES Relay Module power before
removing amplifier.
Installing Plug-In Flame
Signal Amplifier (Fig. 2)
W ARNING
Electric Shock Hazard.
Can cause electrical shock,
serious injury or death.
Disconnect the power supply before beginning
installation. More than one power supply
disconnection can be involved.
65-0109—6 4
Fig. 2. Installing flame signal amplifier.
Wiring
CAUTION
Electrical Shock Hazard.
Can cause electrical shock or equipment damage.
Disconnect power supply bef ore beginning installation.
More than one disconnection can be involved.
1. Remove the 7800 SERIES Relay Module from the
wiring subbase.
2. Refer to Fig. 3 for proper flame detector wiring.
3. Disconnect power supply before making wiring
connections to prevent electrical shock and equipment
damage.
4. All wiring must comply with appropriate electrical
codes, ordinances and regulations including NEC
Class 1 (Line Voltage) wiring where required.
Page 5
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
FLAME ROD
PHOTOCELL
F
X
G
X
INFRARED (C7015)
WHITE
F
BROWN
G
ULTRAVIOLET (C7027/C7035/C7044)
BLUE
F
1
WHITE
G
SOLID STATE
ULTRAVIOLET (C7012A,C)
BLUE
F
2
YELLOW
G
BLACK
L1
BLACK
L2
4
SOLID STATE SELF-CHECKING
ULTRAVIOLET (C7061A)
F
X
G
X
6
5
4
3
F G
F
3a
G
SHUTTER
SHUTTER
3
L2
REMOTE
SENSOR
3b
L1
L2
7800 SERIES
7
EARTH
2b
GROUND
8
2a
1
C7076A
OR
C7076D
2
TERMINAL
BLOCK
L1 (HOT)
L2 (COMMON)
22
5
SOLID STATE SELF-CHECKING
ULTRAVIOLET (C7012E,F)
C7076A,D ULTRAVIOLET DETECTOR
2
YELLOW
G
WHITE
22
WHITE
L2
BLACK
L1
BLACK
L2
3
BLUE
F
SOLID STATE SELF-CHECKING
ULTRAVIOLET (C7024E,F – E SHOWN)
BLUE
2
1
2
3
4
YELLOW
G
WHITE
22
WHITE
N
!
CAUTION: EQUIPMENT DAMAGE HAZARD. INCORRECT WIRING POLARITY CAN DAMAGE OR DESTROY UV SENSING TUBES.
CONNECT FLAME DETECTOR WIRES ACCORDING TO FOOTNOTES 1 AND 2 TO PREVENT UV SENSING TUBE DAMAGE.FLAME DETECTOR
LEADS ARE COLOR CODED. THE BLUE LEAD MUST BE CONNECTED TO THE F TERMINAL AND THE WHITE MUST BE CONNECTED TO
THE G TERMINAL. THE UV SENSING TUBE IS POLARITY SENSITIVE.
FLAME DETECTOR LEADS ARE COLOR CODED. THE BLUE LEAD MUST BE CONNECTED TO THE F TERMINAL AND THE YELLOW MUST
BE CONNECTED TO THE G TERMINAL. THE UV SENSING TUBE IS POLARITY SENSITIVE.
!
CAUTION: EQUIPMENT DAMAGE HAZARD. INCORRECT VOLTAGE CAN DAMAGE SHUTTER MECHANISM ONLY ON EC7800 SERIES
RELAY MODULES. INSTALL A 200/220/240 VAC TO 120 VAC, 10VA MINIMUM, STEPDOWN TRANSFORMER (NOT PROVIDED) TO DRIVE
THE SHUTTER MECHANISM.
DO NOT USE 0.8/1 SECOND FFRT AMPLIFIER WITH C7012A,C FLAME DETECTOR.
3
BLUE
F
F
YELLOW
2
G
WHITE
22
WHITE
L2
RED
3
BLACK
L2
M11462B
Fig. 3. Flame detector wiring.
65-0109—65
Page 6
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
5. Use recommended wire size and type no. 18 copper
conductors TTW(60C) or THW (75C) or THNN(90C).
6. Use recommended wire routing:
a. Keep the flame signal leadwire as short as
possible from the detector to the 7800 SERIES
Relay Module. The maximum permissible leadwire
length depends on the type of leadwire, conduit
type and leadwire diameter. The ultimate limiting
factor for flame signal leadwire length is the flame
signal voltage.
b. Do not run high voltage ignition tr ansformer wires
in the same conduit with the flame detection wiring.
c. If the flame detector leadwires are not long
enough to reach the 7800 SERIES Relay Module
electrical connectors, make splices in a junction
box.
1. Enclose scanner wiring without armor cable in
metal cable or conduit.
2. Follow flame detector Instructions.
7. Check wiring, see Fig. 4.
8. Install 7800 SERIES Relay Module.
9. Restore power to the 7800 SERIES Relay Module.
Flame detector wiring is shown in Fig. 3.
CHECKOUT
3 Amplifier is securely mounted on the 7800 SERIES
Relay Module.
4 Detectors are properly positioned and cleaned
according to Detector Instructions.
5 Correct combination of amplifier and flame detector is
used.
Flame Signal Measurement (Fig. 4)
Flame signal can be measured at the Flame Signal Test
Jacks, see Fig. 4, and at the Keyboard Display Module.
Measure the flame signal at the appropriate times defined in
the Checkout section; see applicable 7800 SERIES Relay
Module Instructions. See Table 3 for acceptable and
maximum flame signal voltage strengths.
POSITIVE (+)
NEGATIVE (-)
METER LEAD
FLAME SIMULATOR
TEST JACK
METER LEAD
ONE
MEGOHM/VOLT
METER
Preliminary Inspection
Make certain that:
1 Wiring connections are correct and all terminal screws
and electrical connections are tight.
2 Proper flame failure response time is selected.
Fig. 4. Flame signal measurement with meter.
Table 3. Flame signal.
Flame Detector Flame Signal Amplifier
Flame Rod Photocell
C7012A,C
C7012E,F
c
c
R7847A,B
R7847C
C7015A R7848A,B
C7024E,F R7824C
C7027A
R7849A,B
b
d,e
b
d,e
b
Minimum Acceptable
Steady dc Voltage
1.25 Vdc 5.0 Vdc at Keyboard Display
a
Maximum Expected dc Voltage
Module or on volt-ohmmeter
C7035A
C7044A
C7061A R7861A
C7076A,D R7886A
a
This minimum or stronger signal can be easily obtained if the detector is correctly installed and positioned to properly sense
d
d
the flame. Obtain this voltage before completing checkout.
b
The flame amplifiers are Ampli-Check® type.
c
Adjust slightly, or face the pipe down, or extend the sight pipe on C7012A,C,E,F applications to obtain a maximum flame signal
reading less than 5.0 volts.
d
The flame signal amplifier circuitry is tested one-half second every five seconds during burner operation and shuts down the
burner if the amplifier fails (all installations).
e
R7824C, Series 2 or greater, and R7847C, Series 4 or greater, pulse the shutter when the flame signal reaches 1.5 Vdc.
M11459A
e
65-0109—6 6
Page 7
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
CAUTION
Equipment Damage Hazard.
Improper wiring can destroy ultraviolet
sensing tube.
Carefully follow polarity sensitive wiring instructions for the
C7027, C7035, C7044, C7012, C7024, C7061 and C7076.
Reversing the leadwires, ev en momentar ily, can destroy
the ultraviolet sensing tube.
1. Connect blue leadwire from detector to terminal F and
white leadwire from C7027/C7035/C7044/C7061 to
terminal G.
2. Connect blue leadwire from detector to terminal F and
yellow leadwire from C7012/C7024 to terminal G.
3. Follow lightoff Instructions for applicable 7800 SERIES
Relay Module.
Measuring Flame Signal
With Keyboard Display Module
Consult Instructions for applicable 7800 SERIES Relay
Module or Keyboard Display Module.
Measuring Flame Signal
with a Volt Ohmmeter
Two test jacks, positive and negative (Com) are accessible on
the top of the amplifier when plugged into the 7800 SERIES
Relay Module. These jacks are provided for monitoring flame
signal strength. Use a one megohm/volt meter to measure the
flame signal strength. Connect the positive meter lead (red) to
the positive (+) amplifier test jack and the negative meter lead
(black) to the negative (-) amplifier test jack. The test jacks
use standard 0.180 inch diameter voltmeter probes. A
minimum 1.25 Vdc flame signal is required.
The flame signal for the pilot alone, the main burner flame
alone, and both together must be steady and a minimum of
1.25V. If the flame signal is unsteady, or less than the
minimum acceptable voltage, check the flame detector
installation and circuitry in the following procedure.
1. Check the supply voltages at terminals (L1) and L2 (N).
Make sure the master switch is closed, connections are
correct, and the power supply is of the correct voltage
and frequency and is sinusoidal.
2. Check the detector wiring for defects including:
a. Incorrect connections.
b. Wrong type of wire.
c. Deteriorated wire.
d. Open circuits.
e. Short circuits.
f. Leakage paths caused by moisture, soot or
accumulated dirt.
3. For a flame rod, make sure:
a. There is enough ground area.
b. The flame rod is properly located in the flame.
c. Temperature at the flame rod insulator is no
greater than 500°F (260°C).
4. For all optical detectors, clean the detector viewing
window, lens, and inside of the sight pipe as applicable.
5. With the burner running, check the temperature at the
detector. If it exceeds the detector maximum rated
temperature:
a. Add a heat block to stop conducted heat traveling
up the sight pipe.
b. Add a shield or screen to reflect radiated heat.
c. Add cooling (refer to sight pipe ventilation in the
detector Instructions).
6. Make sure that the flame adjustment is not too lean.
7. Make sure the optical detector is properly sighting the
flame.
8. If necessary, resight or reposition the detector.
9. If you cannot obtain proper operation, replace the plug-
in amplifier.
10. If you cannot yet obtain proper operation, replace the
flame detector.
IMPORT ANT
If you make any changes to the flame detection
system, repeat all required Checkout tests in
Checkout section of the Instructions for the
applicable 7800 SERIES Relay Module.
65-0109—67
Page 8
R7824, R7847, R7849, R7861, R7886 AMPLIFIERS FOR 7800 SERIES RELAY MODULES
Home and Building Control
Honeywell Inc.
Honeywell Plaza
P.O. Box 524
Minneapolis MN 55408-0524
Honeywell Latin American Region
480 Sawgrass Corporate Parkway
Suite 200
Sunrise FL 33325
65-0109—6 G.R. Rev. 7-98
65-0109—6 8
Home and Building Control
Honeywell Limited-Honeywell Limitée
155 Gordon Baker Road
North York, Ontario
M2H 3N7
Honeywell Europe S.A.
3 Avenue du Bourget
1140 Brussels
Belgium
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
Honeywell Asia Pacific Inc.
Room 3213-3225
Sun Hung Kai Centre
No. 30 Harbour Road
Wanchai
Hong Kong
www.honeywell.com
Loading...