How it Works
Greenheck
Loading...
331-2968
User Manual
5 pgs563 Kb0

Greenheck 331-2968 User Manual

Download
Page 1
SELECTING AN ACTUATOR
Step 1
Determine if the actuators need to be electric, pneumatic, or manual.
Step 2
If the actuators are to be electric, determine what voltage (120 Vac, 24 Vac, etc.) and what Hertz (50 or 60
cycles/sec.) are required . If the voltage requirement is not the same as the actuator, (i.e. the motor is 120 Vac and the requirement is 460 Vac) a transformer is needed. Pneumatic actuators require 20 psi supply.
Step 3
If the actuator is manual, then refer to the 'Manual Hand Quadrant' section on Page 3.
Step 4
If the actuator is either electric or pneumatic, then the operation type must be determined:
1) Two position – spring return See tables on following pages
2) Two position (power open – power closed) See tables on following pages
3) Floating (power open – power closed) See tables on following pages
4) Modulating – spring return See tables on following pages
5) Modulating (power open – power closed) See tables on following pages
2) Two position (power open – power closed): This type of actuator will power in either direction. When the power supply is removed (or turned off), the actuator will fail in place.
3) Floating (power open – power closed): This type of actuator is powered in both directions and will stop in any position. No spring is used.
4) Modulating – spring return: This type of actuator will power in either direction and will spring return upon power loss much like the two position actuators. The difference is that a control signal (4-20 mAdc, 0-10 Vdc, etc.) is used. The control signal acts much like a valve; as the signal is increased or decreased, the actuator will open or close or vice versa.
5) Modulating (power open – power closed): This type of actuator is the same as #3, except for its response to a control signal input (4-20 mAdc, 0-10 Vdc, etc.).
Step 5
If the actuator is pneumatic and needs to be modulating, a pilot positioner is required. A pilot positioner uses
the control signal (usually 3-15 psi) to vary the amount of supply pressure entering the actuator. Please note that the use of a pilot positioner will decrease the square foot rating of the actuator by 20%. Consult factory.
Step 6
Once the actuator operation is determined, then the fail position must be known. There are two options:
1) Power open – fail close
2) Power close – fail open
* If a non-spring return actuator is required, then the fail positions above
would become "fail in place."
Step 7
Auxiliary Switch – Separate switch in actuator which can be wired to either
make a circuit (Normally Open) or break a circuit (Normally Closed) when actuated. Switch is at end of power stroke for Siebe (Barber-Colman); actuation point is adjustable in Belimo.
Common
Step 8
Determine if the actuator is to be:
1) Internally mounted: The actuator is mounted in the airstream.
2) Externally mounted: The actuator is mounted out of the airstream at factory in a sleeve or external sidplate
3) External kit: The actuator is installed out of the airstream in the field.
Step 9
At this point there may be more than one actuator from which to choose. So the final step is to determine
which actuator will best operate the damper sizes needed. An actuator selection table is found on the follow­ing pages. If you need assistance, contact your local representative or Greenheck.
Normally Closed
Normally Open
Page 2
A
A
Actuator Selection for Control Dampers
VCD Actuator Limitations
Model Volt. Freq Torque With Without
TF-24 TF-24S FSLF-24 FSLF-24S LF-24 LF-24S FSNF-24 FSNF-24S AF-24 AF-24S FSAF-24 TF-120 TF-120S FSLF-120 FSLF-120S LF-120 LF-120S FSNF-120 FSNF-120S AF-120
F-120S FSLF-230 FSLF-230S FSNF-230 FSNF-230S AF-230 A F-230S
ML8202F1006 30 7 12 383264 See Page 4 ML8302F1004 30 7 12 383265 See Page 4 MS8105A1130 44 7 12 384189 -­MS8209F1003 80 12 20 382733 ACT-MS8209-24V MS8309F1001 80 12 20 382734 ACT-MS8309-24V MS8110A1206 88 12 20 includes auxiliary SPDT end switches 383818 -­MS8120F1002 175 25 50 382824 880349 MS8120F1200 175 25 50 includes auxiliary SPDT end switches 383255 831682 ML4202F1000 30 7 12 383260 See Page 4 ML4302F1008 30 7 12 383261 See Page 4 MS4209F1007 80 12 20 382731 See Page 4 MS4309F1005 80 12 20 382732 See Page 4 MS4120F1006 175 25 50 382823 880347 MS4120F1204 175 25 50 includes auxiliary SPDT end switches 383024 831681 ML4702F1009 30 7 12 383262 829879 ML4802F1007 30 7 12 383263 829878 MS4709F1014 80 12 20 382735 ACT-MS4709-230V MS4809F1012 80 12 20 382736 ACT-MS4809-230V MS4620F1005 175 25 50 382825 880348 MS4620F1203 175 25 50 includes auxiliary SPDT end switches 383254 831683
MA-305 MA-305-500 MA-318 MA-318-500 MA6-318-500 MA-405 MA-405-500 MA-418 MA-418-500 MA6-418-500 MA-419 60 MA-419-500 60 MA5-419 50 MA5-419-500 50 MA6-419-500 60 MA7-419-500 50
GGD221.1U 120 50/60 GGD121.1U 24 50/60 GGD321.1U 240 50/60
24 50/60 24 in.
120 50/60 24 in.
230 50/60 24 in.
24 50/60 24 in.
120
230
24 60 24 in.
120
240
(in. lbs.)
(Hz)
18 18 30 30 35 35 70
70 133 133 133
18
18
30
30
35
35
70
70 133 133
30
30
70
70 133 133
60 24 in.
50/60 24 in.
16
16
60
60
60
16
142 142 142
16
60
60
60
60
60
60
60
60
60
60 24 in.
Max. Damper Sq/Ft
Seals Seals Diameter (includes actuator)
4.5 9 384237
4.5 9 includes auxiliary SPDT end switches 384238 7 12 383241 832778 7 12 includes auxiliary SPDT end switches 383394 832779 7 12 381724 ACT-LF24 7 12 includes auxiliary SPDT end switches 381725 ACT-LF24S
12 20 382889 ACT-FSNF24 12 20 includes auxiliary SPDT end switches 382966 ACT-FSNF24S 25 50 381085 ACT-AF24 25 50 includes auxiliary SPDT end switches 381152 ACT-AF24S 25 50 383413 383413
4.5 9 384241
4.5 9 includes auxiliary SPDT end switches 384236 7 12 383242 832776 7 12 includes auxiliary SPDT end switches 383392 832777 7 12 381722 ACT-LF120 7 12 includes auxiliary SPDT end switches 381723 ACT-LF120S
12 20 382888 ACT-FSNF120 12 20 includes auxiliary SPDT end switches 382965 ACT-FSNF120S 25 50 381087 ACT-AF120 25 50 includes auxiliary SPDT end switches 381151
7 12 383399 833249 7 12 includes auxiliary SPDT end switches 383400 833250
12 20 382963 ACT-FSNF230 12 20 includes auxiliary SPDT end switches 382964 ACT-FSNF230S 25 50 381598 ACT-AF230 25 50 includes auxiliary SPDT end switches 381599 A CT-AF230S
6 12 380712 ACT-MA305-24V 6 12 Includes SPDT end switch 380720 ACT-MA305-500-24V
25 50 380713 ACT-MA318-24V 25 50 Includes SPDT end switch 380721 ACT-MA318-500-24V 25 50 Explosion proof enclosure with end switch 381661 A CT-MA6318500-24V
6 12 380708 ACT-MA405-120V 6 12 Includes SPDT end switch 380722 ACT-MA405-500-120V
25 50 380709 ACT-MA418-120V 25 50 Includes SPDT end switch 380723 ACT-MA418-500-120V 25 50 Explosion proof enclosure with end switch 380806 A CT-MA6418500-120V 25 50 380813 ACT-MA419-230V 25 50 Includes SPDT end switch 381593 ACT-MA419-500-240V 25 50 381205 ACT-MA5-419-220V 25 50 Includes SPDT end switch 381594 ACT-MA5419500-240V 25 50 Explosion proof enclosure with end switch 381595 ACT-MA6419500-240V 25 50 Explosion proof enclosure with end switch 381597 A CT-MA7419500-240V
25 50 24" 382188 ACT-GGD221.1U-115V 25 50 24" 382279 ACT-GGD121.1U-24V 25 50 24" 382737 ACT-GGD321.1U-230V
Electric
VCDR Actuator External Mount
Maximum Description Part # Actuator Kit #
Two-position Spring Return
1
Belimo
Honeywell
Invensys (TAC)
24 in.
Siemens
CTAF120S
Consult factory for actuator applications on UL rated fire and smoke dampers.
NEMA 4, 4X & NEMA 7 housing are available.
1
Unless otherwise specified, spring return actuators will be linked "power open - fail closed" which is also called "normally closed" or "NC". If "power closed - fail open" operation is desired, be sure to indicate this requirement. "Power closed - fail open" is also referred to as "normally open" or "NO".
Page 3
V
Actuator Selection for Control Dampers
VCD Actuator Limitations
Model
oltageFreq. Manufacturer Torque With Without Maximum Description Part # Actuator Kit #
(Hz) (in. lbs.) Seals Seals Diameter (includes actuator)
Max. Damper Sq/Ft
Two-position NON Spring Return
MC431 120 60 Invensys 220 50 100 24 in. Requires SPDT 3 wire controller 381149 ACT-MC431-120V
TF24-SR 24 50/60 Belimo 18 4.5 9 24 in. 2 to 10 volts DC 384239 -­TF24-SR-S 24 50-60 Belimo 18 4.5 9 24 in. 2 to 10 volts DC with end switch 384240 -­LF24-SR 24 50/60 Belimo 35 7 12 24 in. 0-10 volts DC 381737 ACT-LF24SR LF24-SR-S 24 50/60 Belimo 35 7 12 24 in. 0-10 volts DC with end switch 383011 833253 NF24-SR 24 50/60 Belimo 60 12 20 24 in. 0-10 volts DC 381736 ACT-NF24SR NF24-SR-S 24 50/60 Belimo 60 12 20 24 in. 0-10 volts DC with end switch 383012 -­AF24-SR 24 50/60 Belimo 133 25 50 24 in. 0-10 volts DC 381150 ACT-AF24-SR AF24-MFT-S 24 50/60 Belimo 133 25 50 24 in. 0-10 volts DC with end switch 381600 ACT-AF-24-MFT-S MS7505A2008 24 50/60 Honeywell 44 7 12 24 in. 0 or 2-10 volts DC 383740 -­MS7505A2130 24 50/60 Honeywell 44 7 12 24 in. 0 or 2-10 volts DC with end switch 384133 -­MS7505A2030 24 50/60 Honeywell 44 7 12 24 in. 0 or 2-10 volts DC 384187 -­M9185D-1004 24 50/60 Honeywell 60 12 20 24 in. Series 90 (135 ohm slidewire) 380949 ACT-M9185D1012-24V MS7510A2206 24 50/60 Honeywell 88 12 20 24 in. 0 or 2-10 volts DC with end switch 383213 -­MS7510A2008 24 50/60 Honeywell 88 12 20 24 in. 0 or 2-10 volts DC 383739 -­MS7520A2007 24 50/60 Honeywell 175 25 50 24 in. 0 or 2-10 volts DC 383214 -­MS7520A2015/B 24 50/60 Honeywell 175 25 50 24 in. 0 or 2-10 volts DC 383785 -­MS7520A2205 24 50/60 Honeywell 175 25 50 24 in. 0 or 2-10 volts DC with end switch 383738 -­MS7520A2213 24 50/60 Honeywell 175 25 50 24 in. 0 or 2-10 volts DC with end switch 383784 --
LMB24-SR 24 50/60 Belimo 45 7 12 24 in. 0-10 volts DC 381728 833286 NMB24-SR 24 50/60 Belimo 60 10 20 24 in. 0-10 volts DC 381138 833288 AMB-24 SR 24 50/60 Belimo 180 25 50 24 in. 0-10 volts DC 382131 833290
LMB24-3 24 50/60 NMB24-3 24 50/60 Belimo 90 10 20 24 in. 381601 ACT-NM24 AMB24-3 24 50/60 Belimo 180 25 50 24 in. 381602 ACT-AM24 M6184D1035 24 50/60 Honeywell 150 25 50 24 in. 381715 --
AE-201 Invensys (TAC) 381477 Not Applicable (N/A)
T-249 Invensys (TAC) 380842 --
50017460-001 Honeywell 381043 --
1/2 in. dia. shaft - For use on all VCDs 48 in. wide and less (or 96 in. wide if height is 24 in. or less) 1 in. dia. shaft - For use on all VCDs over 48 in. wide and over 24 in. high (for use on all VCDs over 96 in. wide)
331-4551 Siemens 10 10 20 24 in. #3 Actuator 454130 ACT-331-4551-P 331-2968 Siemens 30 25 50 24 in. #4 Actuator 451918 -­331-2976 Siemens 30 25 50 24 in. #4 Actuator 454129 ACT-331-2976-P 331-2856 Siemens 50 42 84 24 in. #6 Actuator 451919 ACT-331-2856-P MK2-7121 Invensys 67.5 42 84 24 in. 454138 ACT-MK2-7121-P MK4-7121 Invensys 67.5 42 84 24 in. 382845 --
332-4551 Siemens 10 8 16 24 in. #3 Actuator with pilot positioner 457043 ACT-332-4551-P 332-2976 Siemens 30 20 40 24 in. #4 Actuator with pilot positioner 457384 ACT-332-2976-P 332-2856 Siemens 50 35 70 24 in. #6 Actuator with pilot positioner 457407 ACT-332-2856-P
1/2 in. Extension pin kit 1/2 in. Crankarm (with bolt and nut)
Belimo 45 7 12 24 in. 381726 ACT-LM24
Plate mounted transformer - Primary 120 Vac, Secondary 24 Vac Compatible on any 24 Vac Actuator Plate mounted transformer - Primary 480/277/240/208 Vac, Secondary 120 Vac. Compatible on any 120 Vac Actuator. Transformer (mounted within actuator) to convert Honeywell model M9185D-1012 modulating actuator to 120, 208, or 240 Vac.
1 in. Crankarm (with bolt and nut) 816252 N/A Standoff bracket with ball bearing (for volume control dampers) 815027 N/A Standoff bracket without ball bearing (for manual balancing dampers) 651812 N/A 6 in. long, 1/2 in. diameter control shaft 452509 N/A
8.5 in., 1/2 in. diameter control shaft 455064 N/A Retaining clip used to hold control shaft on axle pin (required with control shaft) 451738 N/A
Consult factory for actuator applications on UL rated fire and smoke dampers.
Electric
VCDR Actuator External Mount
Modulating Spring Return
1
Modulating NON Spring Return
Floating PO/PC
Transformers
Manual Hand Quadrant
Pneumatic
Two-position Spring Return
Modulating Spring Return
1
Miscellaneous Parts
N/A 811518 N/A 813938
1
809735 N/A 812097 N/A
NEMA 4, 4X & NEMA 7 housing are available.
1
Unless otherwise specified, spring return actuators will be linked "power open - fail closed" which is also called "normally closed" or "NC". If "power closed - fail open" operation is desired, be sure to indicate this requirement. "Power closed - fail open" is also referred to as "normally open" or "NO".
Page 4
POWER CLOSED
FAIL OPEN
Power Direction
Power Direction
POWER OPEN
FAIL CLOSED
Left-Hand Drive Right-Hand Drive
Voltage Actuator Model Actuator Kit Actuator Part # Spring Return Action Driving Torque
115 Vac
ML4302F1008 829876 383261
30 in.lb.
MS4309F1005 ACT-MS4309-115V 382732
CCW
80 in.lb.
24 Vac
ML8302F1004 829880 383265
30 in.lb.
MS8309F1001 ACT-MS8309-24V 382734
80 in.lb.
Honeywell, ML Series External Actuator Kits
The ML-XXXX A & MS
series actuators can be
mounted as shown here.
Voltage Actuator Model Actuator Kit Actuator Part # Spring Return Action Driving Torque
115 Vac
ML4202F1000 829877 383260
30 in.lb.
MS4209F1007 ACT-MS4209-115V 382731
CW
80 in.lb.
24 Vac
ML8202F1006 829881 383264
30 in.lb.
MS8209F1003 ACT-MS8209-24V 382733
80 in.lb.
The ML-XXXX B series actuators can be mounted as shown here.
Default in CAPS for FSD, SMD, and CFSD
Power Direction
POWER CLOSED
FAIL OPEN
Right-Hand Drive
Power Direction
POWER OPEN
FAIL CLOSED
Left-Hand Drive
Default in CAPS for VCD
& MS
Item No. Part Number Qty Description
1 1 ML ACTUATOR 2 822979 1 ACT. MOUNTING BRACKET 3 702973 1 STANDOFF BRACKET 4 415264 8 1/4-20 X 1/2 TCS
TORQUE SET SCREWS
TO 50-55 IN-LBS
TORQUE SET SCREWS
TO 50-55 IN-LBS
FSD MOUNTING
VCD MOUNTING
Right Hand (standard on FSD, SMD, CFSD)
Left Hand (standard on VCD)
Page 5
New Part #
Old Part #
Description Dampers Used On
same as old part #
851038
End Switch Kit
All WDs
826848
MP100A-24V
MP-100 24 V motorpack kit
WD-100 series
826840
MP100A-115V
MP-100 115 V motorpack kit
WD-100 series
826840
MP100A-208V
MP-100 208V motorpack kit
WD-100 series
826840 MP100A-230V MP-100 230V motorpack kit
WD-100 series
826855 MP100A-380V/50HZ MP-100 380V/50HZ motorpack kit
WD-100 series
826844
MP100A-460V
MP-100 460V motorpack kit
WD-100 series
826840 with
#380711
MP100A-115V with
#380711
MP-100 575/600V w/ Micron
Transformer WD-200 series
Replaced with
826851
MP200-24V
MP-200 24V motorpack kit WD-200 series
Replaced with
826842
MP200-115V
MP-200 115V motorpack kit WD-200 series
Replaced with
826842
MP200-208V
MP-200 208V motorpack kit WD-200 series
Replaced with
826842
MP200-230V
MP-200 230V motorpack kit WD-200 series
Replaced with
826857
MP200-380V/50HZ
MP200-380V/50HZ motorpack kit WD-200 series
Replaced with
826847
MP200-460V
MP-200 460V motorpack kit WD-200 series
Replaced with
826842 plus
#380711 MP200-115V with #380711
MP-200 575/600V w/ Micron
Transformer WD-200 series
826851
MP210-24V
MP-210 24 V motorpack WD-200 series
826842
MP210-115V
MP-210 115 V motorpack WD-200 series
826842
MP210-208V
MP-210 208 V motorpack WD-200 series
826842
MP210-230V
MP-210 230 V motorpack WD-200 series
826857
MP210-380V/50HZ
MP210-380V/50HZ motorpack WD-200 series
826847
MP210-460V
MP-210 460 V motorpack WD-200 series
826842 with
#380711 MP210-115V with #380711
MP-210 575/600V w/ Micron
Transformer WD-200 series
826858
MP220A-24V
MP-220A-24V motorpack WD-200 series
826860
MP220A-115V
MP-220A-115V motorpack WD-200 series 826860 MP220A-230/460V MP-220A-240V motorpack WD-200 series 826860
MP220A-208V
MP-220A-208V motorpack WD-200 series 826865 MP-220A-380V/50HZ MP-220A-308V motorpack WD-200 series
826860 with
#380711
MP220A-115V with
380711
MP-220A-115V motorpack w/
Transformer WD-200 series
826861 MP-220A-230/460V MP-220-460V motorpack WD-200 series
Replaced with
826850
MP300-24V
MP-300 24V motorpack kit
WD-300 series
Replaced with
826841
MP300-115V
MP-300 115V motorpack kit
WD-300 series
Replaced with
826841
MP300-208V
MP-300 208V motorpack kit
WD-300 series
Replaced with
826841
MP300-230V
MP-300 230V motorpack kit
WD-300 series
Replaced with
826856 MP-300-380V/50HZ MP-300 380V/50HZ motorpack kit
WD-300 series
Replaced with
826846
MP300-460V
MP-300 460V motorpack kit
WD-300 series
Replaced with
826841 plus
#380711 MP300-115V with #380711
MP-300 575/600V w/ Micron
Transformer
WD-300 series
826850
MP310-24V
MP-310 24V motorpack kit
WD-300 series
826841
MP310-115V
MP-310 115V motorpack kit
WD-300 series
826841
MP310-208V
MP-310 208V motorpack kit
WD-300 series
826841
MP310-230V
MP-310 230V motorpack kit
WD-300 series
826856
MP310-380V/50HZ
MP-310-380V/50HZ motorpack kit
WD-300 series
826846
MP310-460V
MP-310 460V motorpack kit
WD-300 series
826841 with
#380711 MP310-115V with #380711
MP-310 575/600V w/ Micron
Transformer
WD-300 series
826849
MP323-24V
MP-323 24V motorpack kit
WD-323
826843
MP323-115V
MP-323 115V motorpack kit
WD-323
826843
MP323-208V
MP-323 208V motorpack kit
WD-323
826843
MP323-230V
MP-323 230V motorpack kit
WD-323
826845
MP323-460V
MP-323 460V motorpack kit
WD-323
826843 with
#380711 MP323-115V with #380711
MP-323 575/600V w/ Micron
Transformer
WD-323
WD Dam
p
er Series Actuator Selection
Copyright ©2009 Greenheck Corporation
Actuator Selection Rev. 5 November 2009
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use