SUMMER MODE
1. In operating mode, pressing the ‘PROG’
and ‘TIME’ (combination of buttons) to set
the summer mode. The clock will forward
on one hour (showing the icon
S
Dia.22).
Dia.22
(Example: the clock will change to ‘11.00’, if the time is ‘10.00’ now
ress “PROG’ and ‘TIME’.)
p
Note: Pressing the ‘PROG’ and ‘TIME’ (combinations of buttons) to exit the summer mode.
Installation / Operating Instruction
for 7 day Fused Timer Spur Switch
Model: T205-C
-
Please read the instructions fully before attempting installation.
WIRING DIAGRAM
T205
L
Supply
N
13A Fuse
Isolation Switch
IMER
T
L
Load
N
BATTERY BACK UP/LIFE
Note: Battery is fully charged after 14.5 hours.
The non-replaceable, fully charged battery, will retain any program information
for a period of 700 hours should their be power loss or the unit switched off with
the double pole isolation switch.
Display is not visible during this period unless a button is pressed.
TECHNICAL INFORMATION
Display: LCD
Working Voltage: 230V-50Hz
Rated Impulse Voltage: 2,500V
Operating Temp: -5°C to +40°C
Operation: Integrated Control
Max Load:
Resistive - 13A
Inductive - 6A
Isolation: Double Pole Isolation
Switch
Conforms to: BS 1363-4:1995+A4:2012,
Working Environment: Indoor use only
Pollution Degree: 2
BS EN 60730-1:2011,
BS EN 60730-2-7:2010.
IMPORTANT
his unit should be installed by a competent person
T
in accordance with the current IET Wiring Regulations.
If in doubt consult a qualified electrician
Timer Spur must not be mounted on a flammable surface.
•
.
• Ensure that the Timer Spur does not come into contact with any
combustible materials such as towels or bedding.
• Ensure at least a 300mm air space is allowed around the Timer Spur
switch.
• A 12mm pattress is provided if extra spacing is required.
• Twin Earth terminal provided.
Note: Where earthing termination is required this must be connected to
a earth terminal as provided in a metal back box.
OPERATING INSTRUCTIONS
‘ON’ Indicator
Fuse
Holder
Dia.1
RESET THE DEVICE
1. To fully reset this unit press the recessed
‘Reset’ button with a insulated blunt probe.
2. A full display will show when the battery is
charged, then revert to the default screen
( : ). No display indicates that the
battery requires charging for a minimum 3
hour period. (Dia.2 - Full display)
Programme
Button
Double Pole
Isolation Switch
Reset
Button
Time
Button
‘+’ and ‘-’
Button
Front Cable
Entry
Dia.2
Your GreenBrook Fused Timer Spur Switch
is guaranteed for 1 year from
This is in addition to your statutory rights.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
GUARANTEE
the date of purchase.
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
info@greenbrook.co.uk
www.greenbrook.co.uk
SETTING THE DAY OF WEEK
AND TIME
Dia.3
Note: Time setting is 24 hour mode.
1. Press the ‘TIME’ button for 2 seconds. Day of
week will start flashing (example shows 7 Day
setting Dia.3)
2. Use the ‘+’ or ‘-’ button to change the
display to the correct day of the week.
3. Press the ‘TIME’ button and the hour digits will
(Dia.4)
Issue no: 705307
flash.
4. Use the ‘+’ or ‘-’ button to set the hours.
5. Press the ‘TIME’ button and the minute digits will
flash. (Dia.5)
6. Use the ‘+’ or ‘-’ button to set the minutes.
7. Press the ‘TIME’ button to save the setting
and return to operating mode.
Dia.4
Note: If ‘+’ or ‘
seconds, the selected time digit will add or
decrease quickly (about 5 steps per second), if
no key is pressed within 60 seconds the display
will return to operating mode.
-’ button is held for more than 2
Dia.5
PROGRAMMING THE
‘ON’/OFF’ TIMES
1. Press the ‘PROG’ button and hold for 2
seconds, after 2 seconds the display will show:
(example shows 7 Day setting
Dia.6)
Dia.6
Note: Only ONE of the following
options can be used at one time.
2. Use the ‘+’ or ‘-’ button to change the day
rouping (PROG) at the top of the display. This
g
will step through the following programming options:
7 DAY - MON TUES WED THU FRI SAT SUN
All of them have the same programming.
OR
5 DAY - MON TUE WED THU FRI
Are grouped as one group, and they will all have the same
programming. SAT and SUN will be programmed individually.
OR
INDIVIDUAL DAY -
Each day will have its program set individually. MON followed
automatically in programming by each of the other days. To copy
times set for an individual day to another day (e.g. copy Sat set
times to Sun), please see PROGRAM
DUPLICATION below.
3. Once the desired day grouping is selected,
press ‘PROG’ button to move onto
programming ON/OFF times. Display will
show PROG 1 ON, and the hour digits flashing
(24 hour clock) (Dia.7).
(Example shown is for 5 + 1 + 1 + day program)
4. Use the ‘+’ or ‘-’ to set the hours and the
‘PROG’ to change between hours and
minutes. Followed by ‘+’ or ‘-’ again to set the
minutes. Press ‘PROG’ to change to program
OFF time. (Dia.8)
5. Use the ‘+’ or ‘-’ to set the OFF time in the
same way as for PROG 1 ON time.
6. Press ‘PROG’ to scroll through program 2 ON,
program 2 OFF, program 3 ON, program 3 OFF,
program 4 ON, program 4 OFF, adding in times
as required. If you wish to omit programmes
just leave dashes in that ON/OFF location.
Press ‘PROG’ to move to the next linked day
(SAT follows the 5 day group automatically)
(Dia.9).
7. Set ON/OFF times as before. Press ‘PROG’ to
move to the next linked day (SUN follows the
SAT automatically) (Dia.10).
8. Set ON/OFF times as before.
9. Once program 4 OFF has been set, press
‘PROG’ to exit program mode and
return to operating mode.
Dia.7
Dia.8
Dia.9
Dia.10
PROGRAM DUPLICATION
There are two copy functions: copy one day to another, or copy one day to all
other days. When programming for ‘Individual Day’ or ‘5 Day’ you can copy
the programmed data from one day to another day.
1. When setting ON time of ‘PROG’ 1, press ‘TIME’ button and then use ‘+’ or ‘-’
to select the day you want to copy.
2. Press ‘TIME’ button twice to copy the data of the selected day to current
day.
Or press ‘TIME’ button for 2 seconds to copy the data of the selected day to
the following days.
(Example shown for copying data TUE to THU)
When the ON/OFF times for WED are set, the
display will show ‘THU’:- (Dia.11).
3. Press ‘TIME’ button then the icon ‘MON’ will
e flashing (Dia.12).
b
4. Use ‘+’ or ‘-’ button to select ‘TUE’, then press
‘TIME’ button twice to copy the data. The
display will show: (Dia.13).
Dia.11
Dia.12
MODIFYING OR ADDING
NEW PROGRAMMES
. Press ‘PROG’ button and hold for approx 2
1
seconds, the display will show: (Dia.14).
2. Use ‘+’ or ‘-’ button to select the day
grouping which requires modifying or a new
day grouping for a new programme.
3. For modification press ‘PROG’ repeatedly to
arrive at the programme time requiring
modification then use ‘+’ or ‘-’ button to
make the change. Press ‘PROG’ repeatedly
again to arrive at the next time requiring
modification and use ‘+’ or ‘-’ button to
make the change.
Dia.13
Dia.14
OPERATING MODE
Note: Operating mode needs to be set to allow programmed times to
function.
To set timer status:-
1. Use’+’ button to set the output mode.
ON - Output to permanently ON and omit the program (Dia.15).
OFF - Output to permanently OFF and omit the program (Dia.16).
ON AUTO - Output to ON until next program OFF period (Dia.17).
OFF AUTO - Output to OFF until next program ON period (Dia.18).
Note: When in program mode display will always show AUTO.
Dia.15
Dia.17
Dia.16
Dia.18
ONE AND TWO HOUR BOOST
1. Pressing ‘-’ (Boost) once in normal
operating mode turns on for 1 hour period
(Dia.19).
2. Pressing ‘-’ (Boost) twice turns output on a
for 2 hour period (Dia.20).
3. Pressing ‘-’ (Boost) button three times
cancels the (Boost) ON period (Dia.21).
Dia.20
Dia.19
Dia.21
Loading...