Instructions for Wired
Doorchimes & Bell Pushes
MODEL NUMBERS -
Doorchimes DH020A-C Galaxy Chime
DH021A-C Tubular Chime
These products should be installed by a
competent person and in accordance with
the current IEE Wiring Regulations.
If in doubt, consult a qualified electrician.
Bell Pushes -
f you have bought a bell push only please
I
go straight to step 3a. in these
instructions.
DP010A-C Black Bell Push
DP020A-C White Bell Push
DP050A-C Brass Plate Bell Push
DP050AC-C Chrome Plate Bell Push
DP080A-C Brass Bell Push
DP220A-C White Bell Push
DPL12A-C - Illuminating Button insert
Brass
DPL13A-C Illuminating Button insert
Silver
(for DPL12A-C & DPL13A-C please also
note step 3b)
DPL03A-C Illuminating Black Bell Push
DPL04A-C Illuminating White Bell Push
(DPL03A-C & DPL04A-C must be used with a
bell transformer)
4. The bell wire is now
ready to wire up the
doorchime to the bell
push.
2. WIRING
YOUR DOORCHIME
1. Unclip top cover.
2. Thread bell wire from the back of
the base and through the large
opening to the left of the keyhole
slot.
3. Insert either one of the stripped
ends to terminal A and the other to
terminal C, ensuring the terminal
screws are tightened securely
afterwards. Do not use terminals
marked B and D.
4. Position the base on the wall
vertically, away from opening
doors, with the battery
compartment at the bottom.
Ensure that it is less than 5 metres
away from the bell push.
5. Use one of the screws and wall
fixings to hang the base on the wall
via the top keyhole slot. Adjust the
screw for a flush fit if required.
This doorchime has a traditional
ding-dong sound and is easily fitted
for use with any bell push.
• Bell wire required
• Bell push required
An ornate bell push can be used if
preferred. (For illuminating bell pushes
a transformer must also be used KingShield model number DAT01A)
• Fixing screws included
• Requires 3 x C cell LR14 batteries
(not included)
PLEASE READ THE FOLLOWING
INSTRUCTIONS FULLY BEFORE
ATTEMPTING INSTALLATION.
1. PREPARING BELL WIRE
1. Using a knife, carefully split the bell
wire down the middle to form two
separate wires, each 30mm long.
2. Strip each wire back to expose
5mm of copper wire.
3. The process will need to be
repeated at the other end of the
bell wire once it has been cut to
the required length.
6. Insert 3 x C cell batteries as per
markings on the inside of the case.
3a. WIRING
YOUR BELL PUSH
1. If necessary, remove the base
cover of the bell push to reveal the
terminal screws.
2. Loosen one of the terminal screws
and wrap one of the stripped ends
of bell wire around the exposed
screw thread, ensuring the screw
is tightened securely afterwards.
Repeat this process for the other
screw terminal and wire.
. Fix the base to the doorframe
3
using two of the screws and
fixings provided. Try to position the
door push in an unexposed place
to protect it from bad weather.
4. Snap the cover back on if
appropriate.
An alternative bell push can be used
with this doorchime, please follow the
instructions on the pack.
ILLUMINATING BUTTON INSERTS
DPL12A-C & DPL13A-C ONLY)
(
Certain bell push models can be
converted to illuminated pushes by
purchasing either a KingShield
DPL12A-C or DPL13A-C bell push
button separately. Please Note:For
illuminated bell pushes, a bell
transformer must be used. KingShield
models - DP050A-C, DP050AC-C,
DP080A-C are all suitable to convert to
illuminated bell pushes.
3b.
TROUBLE SHOOTING
If the doorchime does not work, check
he batteries and also that the bell
t
wire is connected to the correct
terminals. Do not use terminal
marked B.
GUARANTEE
Your KingShield Doorchime & Bell
ushes are guaranteed for 12 months
P
rom the date of purchase. Please
f
retain your till receipt as proof of
purchase. This is in addition to your
statutory rights.
PLEASE KEEP THESE
INSTRUCTIONS SAFE FOR
FUTURE REFERENCE
Simply press the button on the back
through the front panel of the door
push and swap it with the DPL12A-C
or DPL13A-C button. Wire up a bell
transformer following Step 4.
4. USING A TRANSFORMER
For use with an illuminated bell push.
Only an 8Volt 1Amp transformer is
recommended, (KingShield Model
DAT01A). Please carefully follow the
manufacturer’s instructions - use
terminals C and D on the doorchime
case to connect up the transformer.
Remove the batteries from the
doorchime and ensure the power is
switched off at the mains before
attempting any wiring.
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
sal e s @gr e e nbr o o k.c o . uk
W W W. GR E E N BR O O K . C O. U K
Issue No: 703766
Loading...