Instructions for Wired
Doorchimes & Pushes
MODEL NUMBERS -
Doorchimes DH020A-C Galaxy Chime
DH021A-C Tubular Chime
DH050A-C Galaxy Chime Kit
These products should be installed by a
competent person and in accordance with
the current IEE Wiring Regulations.
If in doubt, consult a qualified electrician.
Bell Pushes -
If you have bought a bell push only please
go straight to STEP 3a. in these
instructions.
DP010A-C Black Bell Push
DP020A-C White Bell Push
DP050A-C Brass Plate Bell Push
DP050AC-C Chrome Plate Bell Push
DP080A-C Brass Bell Push
DP220A-C White Bell Push
DPL12A-C ‘Push A Lite’ Brass Push
DPL13A-C ‘Push A Lite’ Silver Button
(for DPL12A-C & DPL13A-C please also
note step 3b)
DPL03A-C Lit (illuminated) Black Bell
DPL04A-C Lit (illuminated) White Bell
(DPL03A-C & DPL04A-C must be used with a
bell transformer)
3. The process will
need to be repeated
at the other end of the
ell wire once it has
b
been cut to the
required length.
. The bell wire is now
4
ready to wire up the doorchime to
the bell push.
2. WIRING
YOUR DOORCHIME
1. Unclip top cover.
2. Thread bell wire from the back of
the base and through the large
opening to the left of the keyhole
slot.
3. Insert either one of the stripped
ends to terminal A and the other to
terminal C, ensuring the terminal
screws are tightened securely
afterwards. Do not use terminals
marked B and D.
4. Position the base on the wall
vertically, away from opening
doors, with the battery
compartment at the bottom.
Ensure that it is less than 5 metres
away from the bell push.
5. Use one of the screws and wall
fixings to hang the base on the wall
via the top keyhole slot. Adjust the
screw for a flush fit if required.
This doorchime has a traditional
ding-dong sound and is easily fitted
for use with any door push.
• Bell wire required (included in
DH050A-C Galaxy Chime Kit)
• Bell push required (included in
DH050A-C Galaxy Chime Kit).
An ornate door push can be used if
preferred. (For lit bell pushes a
transformer must also be used KingShield Model Number
‘DAT01A’)
• Fixing screws included
• Requires 3 x C cell R14 batteries
(not included)
PLEASE READ THE FOLLOWING
INSTRUCTIONS FULLY BEFORE
ATTEMPTING INSTALLATION.
1. PREPARING BELL WIRE
1. Using a knife, carefully split the bell
wire down the middle to form two
separate wires, each 30mm long.
2. Strip each wire back to expose
5mm of copper wire.
6. Insert 3 x C cell batteries as per
markings on the inside of the case.
3a. WIRING
YOUR BELL PUSH
1. If necessary, remove the base
cover of the bell push to reveal the
terminal screws.
2. Loosen one of the terminal screws
and wrap one of the stripped ends
of bell wire around the exposed
screw thread,
ensuring the screw
is tightened securely
afterwards. Repeat
this process for the
other screw terminal
and wire.
3. Fix the base to the doorframe
sing two of the screws and fixings
u
provided. Try to position the door
push in an unexposed place to
protect it from bad weather.
4. Snap the cover back on if
appropriate.
An alternative bell push can be used
with this doorchime, please follow the
instructions on the pack.
3b.
PUSH A LITE BUTTONS
(DPL12 & DPL13 ONLY)
Certain door push models can be
converted to illuminated pushes by
purchasing either a KingShield
DPL12A-C or DPL13A-C bell push
button separately. Please note:For
illuminated pushes, a bell transformer
must be used. KingShield models DP050A-C, DP050AC-C, DP080A-C are
all suitable to convert to illuminated
pushes.
TROUBLE SHOOTING
If the doorchime does not work, check
the batteries and also that the bell
wire is connected to the correct
terminals. Do not use terminal
marked B.
GUARANTEE
Your KingShield doorchime is
guaranteed for 12 months from the
date of purchase. Please retain your till
receipt as proof of purchase. This is in
ddition to your statutory rights.
a
PLEASE KEEP THESE
INSTRUCTIONS SAFE FOR
FUTURE REFERENCE
Simply press the button on the back
through the front panel of the door
push and swap it with the ‘Push A Lite’
button. Wire up a bell transformer
following Step 4.
4. USING A TRANSFORMER
For use with an illuminated bell push.
Only an 8Volt 1Amp transformer is
recommended, (KingShield Model
DAT01A). Please carefully follow the
manufacturer’s instructions - use
terminals C and D on the doorchime
case to connect up the transformer.
Remove the batteries from the
doorchime and ensure the power is
switched off at the mains before
attempting any wiring.
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
sales@greenbrook.co.uk
W W W. G R E E N B R O O K . C O . U K
Issue No: 702517
Loading...