Gree ETAC12HP230V30AA User Manual

E-TAC (GB Series) Packaged Terminal Air Conditioner / Heat Pump 7,000 --- 15,000 Btuh

Performance and Specifications

Engineered Terminal Air Conditioner

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Bu ildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

TABLE OF CONTENTS

APPLICATIONS 3-4.................................

PRODUCT NOMENCLATURE 4.......................

PRODUCT OVERVIEW 5.............................

PRODUCT FEATURES & BENEFITS 6-9.............. .

COASTAL PROTECTION 10.............. . .... . . . . . . .

HEAT PUMP OPERATION

FIELD INSTALLED ACCESSORIES 12-20.............. .

DIMENSIONAL DRAWINGS & INSTALLATION DATA -- NEW CONSTRUCTION 21-25. . .

WALL THERMOSTAT CONNECTIONS 26..............

E-TAC

PAGE

11.............. . .... . .... .

PERFORMANCE AND ELECTRICAL DATA 27-30...... .

EXPANDED OPERATING RATING 31-33...............

INDOOR FAN PERFORANCE DATA 33.................

SOUND DATA 34-35.................................

SOUND TRANSMISSION COEFFICIENT 35. . ...........

OUTDOOR GRILLE SIZING & VENT AIRFLOW. . . . . . 37

TYPICAL WIRING SCHEMATICS ............ 38

ENERGY MANAGEMENT WIRING 39............... . .

MULTIPLE WALL THERMOSTAT WIRING 40....... . . .

GUIDE SPECIFICATION 41-44........................

. ...

2

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

The Gree E-TAC Packaged Terminal Air Conditioning

E-TAC

(E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

apid servicing reduces downtime: complete

• R chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

The following major competitors’ wall

—

sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

E-TAC

g Owner

Initial Cost Savings for the Buildin

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

3

PRODUCT CATALOG NUMBER-NOMENCLATURE

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Cooling Capacity 07 - 7,000 BTUH Electric Heat Capacity

ETAC

12 HP 230V 20 -AA

E-TAC

Fig. 3 – Catalog Number Nomenclature

APPLICATION CONSIDERATIONS

Installation instructions are shipped with all E-TAC units. It is important that air conditioning systems be properly sized and installed for each application in order to achieve the desired temperature and humidity levels within the space to be conditioned. It is strongly recommended that a professional engineer match the E-TAC units with the building structure and climate.

The following application considerations are all important in choosing the proper E-TAC for the building structure.

Undersizing

If an E-TAC unit is undersized (cooling capacity is less than required load for an application), the unit will not be able to cool the space down to the desired temperature during very hot days. The result could be warm and humid or warm and dry conditioned space.

Oversizing

If an E-TAC unit is oversized (cooling capacity is greater than required load for the specific application), the unit will cool the space down to the desired temperature too

The unit will cycle on and off, however, dehumidification only takes place when the unit is operating. The result of this type of application in a hot and/or humid climate would beacool, yet excessively humid, space.

quickly.

Air Infiltration

Excessive air infiltration can intensify problems associated with undersizing or oversizing a E-TAC unit. This can be the cause of insufficient cooling, dehumidification, or heating. Sources of air infiltration include vents, gaps around windows and doors, and improperly sealed floors, ceilings or wall joints.

Condensate Removal

Gree’s E-TAC has a new condensate (water) disposal system. The outdoor fan prop has a built in slinger ring which draws condensate and sprays it on the warm outdoor coil for evaporation. Thus providing better disposal of excess condensate and improving unit operating efficiency.

It is normal and desirable to have some condensate water in the base pan to boost operating efficiency.

NOTE: This unit will not always evaporate 100% of the unit generated condensate and blown in rain water. If it is necessary to control 100% of the condensate, the Drain Kit (Part No.: DRAINKIT-1PK) and a building condensate drain system is recommended.

noitcetorPlatnemnorivnEnoitangiseDseireS

noitcetorPdradnatS-ACATE

C - Sea Coast Protection

Revision Level

WK2-51HUTB000,9-90 WK3-02HUTB000,21-21 WK5-03HUTB000,51-51

gnitaRlacirtcelEepyTledoM

HP1zH06V032/802-V032pmuPtaeH-PH

HP1zH06V562-V562looC/taeH-CH

4

PRODUCT OVERVIEW (E-TAC)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No

expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid

servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see acce

ssory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

This section summarizes product features covered in detail in later sections of this manual.

COIL TUBE SHEETS

OUTDOOR ORIFICE

WIRE SCREEN

DISCHARGE GRILLE

INDOOR-AIR INLET FILTERS

Comfortouch Digital Control

• Temperature Display and Touch Pad on Unit

Precise and easy-to-use

• Continuous Temperature Sensing

• Cooling, Heating and Fan Modes

• Setpoint Stoppers

• Auto Restart and Random Restart Delay

• Freeze Protection

Protects unoccupied rooms from freezing

• Emergency Heat (Heat Pump Models)

• Remote Control Options

FRONT PANEL

Unit Components

Ideal comfort for your guests

One unit for all seasons

Electronic temperature limiting reduces operating costs

Automatically restarts after a power failure

temperatures

Bypasses compressor operation and activates electric heater for guest comfort

The ultimate in installation exibility; Wired, WirelessorEnergyManagement

ACCESSOR

INDOOR

COIL

BASEPAN

ACCESSORY

WALL

SLEEVE

Silencer System

• Three-Speed Indoor Fan

 Morecomfortoptionsforgueststochoosefrom

• Dual Motor Technology

Separate indoor and outdoor motors allows one of the

• AeroQuiet Indoor Blower Wheel

quietestandmostefcientunitsintheindustry

 Providesquiet andconsistent airow formaximum

guest comfort

• Rotary Compressor Technology

Quiet operation and low sound transmission indoors

•Insulated Bulkhead Between Indoors and Outdoors

Quiet operation and low sound transmission indoors

Smartfan Comfort Control

•

Programmable Constant Fan Operation

Gree customized comfort in heating or cooling modes.

• Quiet Fan Start-Up and Stops

Smooth ramp-up and ramp-down of fan speed for quiet comfort

OUTDOOR

GRILLE

E-TAC

5

E-TAC PRODUCT FEATURES AND BENEFITS

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

E-TAC 5-YEAR WARRANTY

All E-TACs are protected by a ve-year limited warranty.

•Two-yearpartsandlaborlimitedwarranty

• Three years additional parts andlabor coverage on

the sealed refrigeration system

• Limitedthreeyears(years3-5)parts-onlycoverage

TWO--PIECE LIFETIME INDOOR FILTER

E-TAC

Two--piece removable filters easily slide in and out from the front of the E-TAC unit and are interchangeable. The front panel does not need to be removed to access or change the filters. The filters are washable and permanent.

EASY ACCESS TO CHASSIS

Access to the chassis simply requires removing front panel, then four easy to access screws and then sliding the chassis out of the sleeve for service or maintenance.

E-TAC GB Series

Packaged Terminal Air Conditioner Limited Warranty

TWO-YEAR PARTS AND LABOR LIMITED WARRANTY – During the ﬁ rst two years after purchase, GREE will, through its authorized independent servicing dealer or service stations*, and free of charge to the user or subsequent users, repair or replace any parts that fail due to defect in material or wor kmanship. The replacement part can be a new or remanufactured part as provided at GREE’S sole option.

EXTENDED THREE-YEAR PARTS AND LABOR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM ONLY – During the third through ﬁ fth years after date

of original purchase, GREE will, through its author ized servicing dealers and service stations* and free of charge to the end user or subsequent users, repair or replace the compressor, condenser, evaporator or connecting tubing if it failed due to defect in material or workmanship. This includes system refrigeration charge. The replacement part can be new or a remanufactured part at GREE’S sole option.

EXTENDED THREE-YEAR PARTS ONLY LIMITED WARRANTY ON NON-SEALED REFRIGERATION SYSTEM ONLY – During the third through ﬁ fth years after date of original

purchase, Gree will, through its authorized servicing dealers and service stations and free of charge to the end user or subsequent users, repair or replace any non-sealed system part (motor, solenoid, thermistor, circuit boards, relays, switch, capacitor, overload, drain valve, fan, stator) if failed due to defect in material or workmanship. The replacement part can be new or a remanufactured part at GREE’S sole option. THIS LIMITED WARRANTY DOES NOT INCLUDE LABOR, user is responsible for labor, including cost of diagnosis of problem, removal and transportation of the air conditioner to and from the service center, and reinstallation charges necessary to accomplish repair.

LIMITATION OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE OR PURPOSE) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH EACH LIMITED WARRANTY IS GIVEN AND APPLIES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER.

ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING HOURS. ALL REPLACEMENT PA RTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.

*Authorized independent dealers or service stations are registered with Gree through its distributor organization.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state.

GREE WILL NOT BE RESPONSIBLE FOR:

1. CLEANING REQUIRED PRIOR TO WARRANTY REPAIR.

2. Standard maintenance, cleaning or damage resulting from failure to perfo rm normal maintenance as outlined in the owner’s manual.

3. Instruction on methods of control and use of air conditioning unit after initial installation.

4. Damage or repairs needed as consequence of faulty installation or application. This is the responsibility of the installer.

5. Failure to start due to voltage conditions, blown fuses, open circuit breakers or any other damages due to the inadequacy or interruption of electrical services.

6. Damage or repairs needed as consequence of any misapplication, abuse, unauthorized alteration, improper servicing or operation.

7. Damage as a result of ﬂ oods, winds, ﬁ res, lightning, accidents, corrosive environment, or other conditions beyond the control of GREE. EXCEPTION TO CORROSIVE ENVIRONMENT EXCLUSION IN ABOVE PARAGRAPH – Packed terminal units (GB Series) built with corrosion protection are exempt from the exclusion – “Corrosive Environment.” The unit model number is identiﬁed on the nameplate with CP sufﬁx.

8. Reimbursement for replacement parts or repair services which are not supplied or designated by GREE and which are speciﬁ cally covered under this warranty.

9. GREE products installed outside the continental U.S.A., Alaska, Hawaii, and Canada.

10. Shipping damage or damage as a result of transporting the unit. This is the responsibility of the selling dealer or the authorized service station.

11. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

12. Warranty coverage of accessor

13. Installations of non-corrosion protected models within one (1) mile of a corrosive body of water or environment shall void the EXTENDED THREE-YEAR PA RTS AND LABOR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM ONLY and EXTENDED THREE-YEAR PA RTS ONLY LIMITED WARRANTY ON

, OR

NON-SEALED REFRIGERATION SYSTEM ONLY limited warranties .

Edition Date: 11-11

y items (wall thermostats, wall sleeves

, etc.)

Exclusive Warranty

2 Air filters

Two --Piece Indoor Filter

A07057

Easy to Access Chassis

GA

OUTDOOR AIR VENTILATION

The unique vent system is activated by a twoposition control. Fresh outside air is redirected by the vent door to the indoor room. A molded plastic filter prevents dirt and debris from entering the room side of the unit. The vent mechanism is made from non corrosive material ensuring reliable operation. A magnet

high-pressure airflow create a tight, draft free seal

when the vent door is closed.

or screw on the door and

The vent will provide fresh air. For vent airflow data see page 37.

A07550

Outdoor Air Ventilation

6

BI--DIRECTIONAL DISCHARGE

)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

GRILLE

The discharge grille is constructed of durable polycarbonate and is reversible. Airflows upward at a 40 degree angle to the floor but can easily be adjusted to an 80 degree angle to the floor.

SYSTEM CONFIGURATION

There are many different configuration possibilities, through both dip switches and the digital keypad, that allow you to configure the E-TAC for your exact application. See Owner’s Manual for more detailed information.

COMFORTOUCH DIGITAL CONTROL

The digital keypad provides a simple to operate control. The large, easy to press, “On/Off”, “Fan Speed”, “Mode”, “Setpoint Up” and “Setpoint Down” buttons make the control easy to operate. LEDs are used to show the operating conditions selected. Large numbers are used to display the Setpoint, and if configured, room air temperature.

STAY DRY DEHUMIDIFICATION

The E-TAC provide users with Stay Dry mode to reduce the humidity in the room, making it more comfortable.

The Stay Dry mode is designed to assist removing extra moisture from the air, not dry it out completely. This is not intended to replace a dehumidifier or act as a dehumidifier.

SLEEP MODE

The E-TAC sleep mode function is geared toward making sleeping conditions more pleasant without your having to get up and adjust the unit while in bed. The sleep mode feature allows a time period between 0.5 to 24 hours for the E-TAC to automatically turn off for a pleasant sleeping experience.

Air discharge outward (Default)

Air discharge upward

Bi-Directional Discharge Grille

Dipswitch

UP

Down

Configuration Switches

TEMP CONTROL

Comfortouch Display

Stay Dry Mode

Freeze guard Setpoint Limit 2 Setpoint Limit 1 Fan CON/CYC for cooling Fan CON/CYC for heating Wall Thermostat enable

Electric heat only (for Heat Pumps

DRY

FAN, MODE& OPERATION

A07072

E-TAC

Sleep Mode

7

SETPOINT STOPPER

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

The E-TAC allows property owners to set setpoint

for heating and cooling. The ETAC comes from the factory with the economical range of 65 to 78˚

The cooling and heating setpoint ranges can be adjusted independently and the range may

be expanded or reduced to satisfy your needs and application. .

WALL THERMOSTAT INTERFACE

E-TAC provides a standard wired wall thermostat interface connecting block for quick easy installation. The unit has a removable terminal connector to make

E-TAC

field wiring easy. See more info on wall thermostat connections in the Dimensional Drawings and Installation Data Section.

ENERGY MANAGEMENT INTERFACE

The Energy Management interface is standard and provides a simple to install Energy Management connection. The unit has a removable terminal connector to make field wiring easy. When 24VAC is supplied to the input the unit will turn off. Once the 24VAC is removed (becomes 0 volts), the unit will turn back on.

Note: For more info, see the section in the back, Typical Wiring Schematic For Energy Management Interface.

65 F 78 F

Electronic Setpoint Limiting

R W Y O Gh Gl C

Removable Thermostat Connector

A07634

Energy Management

Terminal Connections

Wall Thermostat

Terminal Connections

Wall Thermostat and Energy Managem ent

Interface

A07073

8

LCDI

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No

expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid

servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see acce

ssory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

The power cord for the 208/230 volt unit provides LCDI protection by automatically disconnecting power during an unsafe condition. Power can be be restored by pressing the RESET button.

POWER CORD PROTECTION

SEAMLESS BASEPAN

Seamless drawn basepan add protection against water accumulation resulting from storm-driven rain with heavy wind. Gree’s deep basepan hold up to 1-3/4

gallons (6.6 liters) of water without spilling.

CONDENSATE DRAIN VALVE

The temperature--activated drain valve opens when the outdoor temperature drops below 55˚ F (12.8˚ C) to prevent water from freezing in the basepan.

CONDENSATE REMOVAL

Gree’s E-TAC has a new condensate (water) disposal system. The suction pull, along with the slinger ring, draws in water which is sprayed up onto the outdoor coil. The water then evaporates, thus providing better disposal of excess condensate and improving unit efficiency.

NOTE: If it is necessary to control 100% of the condensate, the Drain Kit (Part No.: DRAIN-KIT-1PK) is recommended.

LCDI Power Cord Plug Head

A07551

Condensate Drain Valve Prevents Water

from Freezing in Basepan

SLINGER RING

CONDENSER SECTION

Condensate Removal System

A07550

A07678

GA

E-TAC

9

COASTAL PROTECTION

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No

expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid

servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see acce

ssory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

The Gree Coastal E-TAC features a corrosion-resistant coating that exceeds the performance and protection of other products of this kind on the market. The coating pro

iving you added reliability in your business.

g

vides salt air corrosion protection

Install the best in corrosion protection for your property, without the worry of performance degradation, coating breakdown or shortened life.

Gree’s Coastal Units are made with a blue-colored anti-corrosion epoxy treated to resist corrosion. This technology maintains excellent heat transfer properties while extending the coil life against damage from salt air and salt water in seacoast installations. This is a tough epoxy coating that

GA

E-TAC

uniformly covers the outside coil surface with a thick .5 to 1.0 mil layer of protection. This advanced material is highly flexible, eliminating cracking problems with traditional coatings and dipped coils.

COASTAL PREMIUM PROTECTION

• Condenser Coils are coated with a corrosion

resistant epoxy resin providing enhanced resistance to acidic and salt air conditions.

• 1500 hr salt spray tested.

• Durable non-corrosive fan wheel and shroud.

• Added protection with durable powder coated paint.

• All exposed fasteners manufactured of high quality

NOTE: Refer to the product warranty for reduced warranty coverage on standard non-corrosion protected units installed within one mile of the of the sea coast or within a corrosive environment.

stainless steel.

f

i

t

e

r

d

e

C

S

e

a

c

o

a

s

t

n

o

i

t

c

e

t

o

r

P

Corrosion Protection

A09078

10

HEAT PUMPS PAY THEIR

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No

expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid

servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see acce

ssory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

OWN WAY

Heat pump models are available at a nominal additional cost. In many locales, the payback is realized in just a few months

SPECIAL FEATURES

Two-Stage Thermostat:

The indoor thermostat senses the indoor temperature and automatically turns on the electric heat to warm the room quickly. After the desired temperature conditions have been satisfied, the thermostat automatically switches to heat pump mode. If compressor failure occurs, thethermostat willprovide backup electric heat automatically.

Outdoor Thermostat:

During senses outdoor coil temperature. It swit to electric heat mode when the outdoor coil temperature is 28˚ F (--2.2˚ C) or below for one (1) minute. The thermostat switches the unit back to heat pump mode when the outdoor coil temperature rises above 40˚ F (4.4˚ C) for ten (10) minutes, which is enough to provide heat to meet demand. The entire operation is completely automatic.

Reversing Valve:

The reversing valve provides quiet refrigerant flow when energized in heating mode. The valve controls the direction of refrigerant flow for both heating and cooling functions and remains energized as long as the controls are in the heat position. When t cooling controls are activated, the valve automatically reverses to the cooling position.

Manual Comp

This configuration dip switch completely locks out the compressor. See Owners Manual for more details. Note that the compressor and heater do not operate at the same time, thus conserving energy.

the heating cycle, the outdoor thermostat

ches the unit

ressor Override Configuration:

he

HOW THE HEAT PUMP WORKS

In Hot Weather:

Gree’s E-TAC units provide indoor comfort in the same manner as conventional air conditioners, removing heat and humidity from indoor air. The heat and humidity is released to the outdoors. Gree’s high efficiency design saves energy and reduces cooling costs.

In Cool Weather:

When the outdoor coil temperature is above 28˚ F (--2.2˚ C), the heat pump draws heat from outdoor air and uses it to heat indoor air. Since heat is transferred and not produced, Gree’s heat pump uses less electricity and reduces energy costs significantly.

In Sub- Freezing Weather:

When the o (--2.2˚ C) for one (1) minute, the unit automatically switches on a built--in electric heater. The compressor stops and the indoor fan circulates warm air produced by the heater. When the outdoor coil temperature rises above 40˚ F (4.4˚ C) for ten (10) minutes, heat pump operation resumes automatically.

A07553

utdoor coil temperature falls below 28˚ F

A07554

GA

E-TAC

11

FIELD--INSTALLED ACCESSORIES

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No

expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid

servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see acce

ssory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

POLYMER WALL SLEEVES

For the best performance and longest life, Gree recommends genuine polymer wall sleeves for all installations.

All polymer wall sleeves are made from a molded polymer that is designed for strength and durability. This material has excellent corrosion resistance and a flammability rating of UL94--5V.

The sleeve surface is textured to prevent shine and hide scratches. The rib configuration on the sleeve bottom allows easy chassis removal and aids in drainage

E-TAC

Insulated Polymer Wall Sleeve

Part No.: SLEEVE--INSUL--1PK Gree’s accessory insulated polymer wall sleeve,

with factory--installed insulation, provides superior sound absorption, reduces heat loss and prevents sleeve sweating, a condition that can occur when the outside temperature is cold and the indoor conditions are warm and humid.

Non--Insulated Polymer Wall Sleeve

Part No.: WALL--SLEEVE--1PK Gree’s accessory non-insulated polymer wall sleeve provides a superior appearance and protection for many appli

cations.

IMPORTANT

conditions could influence sleeve sweating, a condition that can occur when the outside temperature is cold and the indoor conditions are warm and humid, the Insulated Polymer Wall Sleeve should be considered.

For applications where weather

f

i

t

e

r

d

e

C

S

e

a

c

o

a

s

t

The locating holes in the side and top panels allow for

easy fastening of the sleeve to wall openings. Refer to dimension drawings in Typical Wall Installation and Dimension section.

The sleeve’s alpine mist color (a shade of beige) closely matches the front panel and blends in well with any inside or outside decor. The polymer wall sleeve comes in both insulated (factory installed) or non-insulated, to meet the requirements of every application.

n

o

i

t

c

e

t

o

r

P

Corrosion-Protected Polymer Sleeve

42 in

(1067 mm)

(378 mm)

14 7/8 in

A07633

16 in

(406 mm)

12

FIELD--INSTALLED ACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Metal Insulated Wall Sleeves

Part No.: SLEEVE--STEEL--1PK

Gree’s metal wall sleeves are available in a variety of sizes for most applications and difficult installations. Choose from 14--3/4 in., 18 in., 24 in., 26 in., or 28 in. (375 mm, 457mm, 610 mm, 660 mm, and 711 mm) standard depth sizes. All metal wall sleeves come with factory--installed insulation,

SLEEVE--EXT18--1PK SLEEVE--EXT24--1PK SLEEVE--EXT26--1PK SLEEVE--EXT28--1PK

Amounts in ( ) = mm

Metal Wall Sleeve

designed to minimize heat loss, reduce outdoor noise transmissions into the room and prevent sleeve sweating. In addition, the metal wall sleeve provides a flammability rating higher than UL94--5V.

GA

Wall Sleeve Molding Kit

Part No.: SLEEVE–MOLDING For a superior look and to hide any construction

imperfections, use Gree’s wall sleeve molding kit to trim the wall sleeve to the wall. The molding kit is a perfect solution and can be used with any Gree wall sleeve (matches wall sleeve color).

Friedrich (and ZoneAire) Retrofit Wall Sleeve Adapter

Part No.: FR--SLEEVE--EXT

The Friedrich (and ZoneAire) wall sleeve adapter is constructed of metal and is designed to increase the depth of an existing Friedrich T-series or ZoneAire wall sleeve to accommodate all industry standard PTAC units.

42 in

(1067)

16 in (406)

Available in: 14-3/4 in. (375), 18 in. (457), 24 in. (610), 26 in. (660), 28 in. (711)

A07381

1 IN.

(25.4 mm)

1/2 IN.

(12.7 mm)

Wall Sleeve Molding Kit

A08395

16 IN.

(406.4 mm)

42 IN.

(1067 mm)

3 IN.

(76.2 mm)

A08396

Friedrich Wall Sleeve Adapter Kit

E-TAC

13

17

FIELD--INSTALLED ACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

OUTDOOR GRILLES

Polymeric Architectural Outdoor Grilles (Louvered)

Part No.: GRILLE--PLA--BEIGE

GRILLE--PLA--ALPIN

(color matches Gree’s polymer wall sleeve)

GRILLE-PLA-BROWN GRILLE-PLA-WHITE

This value line of polymeric architectural outdoor grilles will blend attractively with most building exteriors. Mounted easily from inside the room, the one--piece, molded grille is designed for protection, enhanced appearance, and superior weather-resistance. The grille is made of durable polymer and has a colorfast, lightly textured finish that blends well with

E-TAC

most exterior finishes.

Aluminum Architectural Outdoor Grilles (Louvered)

Part No.: GRILLE--ALU--CLEAR (anodized aluminum)

GRILLE--ALU--WHITE GRILLE--ALU--BEIGE GRILLE--ALU--ALPIN -Matches wall sleeve

(Custom

colors available)

This premium line of decorative outdoor grilles will enhance the appearance of any building. The grilles are made of strong, durable, extruded, anodized aluminum and are designed to be mounted easily from inside the room. These elegant grilles, available in many standard colors, have baked enamel finishes containing 50% Kynar will withstand the most extreme conditions.

Standard Outdoor Aluminum Grille

Part No.: GRILLE--ALU--STAMP This cost--effective, one--piece standard grille is made

from durable anodized aluminum. The grille is lightweight, has a clear finish, and is easy to install from inside the room.

®

resin, for a superior finish that

IMPORTANT: Gree recommends only the use of Gree-supplied grilles for use with the E-TAC units. However, the architectural designs of a building may dictate the use of special or oversized grilles and/or louvers. Special louvers or any special architectural treatment of the building facade that may restrict free circulation of condenser airflow should be referred to Gree Corporation for evaluation and approval.

See Sizing Outdoor Grille Selection.

f

i

t

e

r

d

e

C

S

e

a

c

o

a

s

t

n

o

i

t

c

e

t

o

r

P

Polymer Architectural Grille

Aluminum Architectural Grille

Standard Grille

GA

14

FIELD--INSTALLED ACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

SUBBASE

Part No.: PTACSUBBASE--A The easy to install, non--electrical subbase provides

mechanical support and requires no wiring.

All subbase models mount to the wall sleeve,and come with adjustable legs and side skirting to provide a finished appearance.

A subbase (or leveling legs) is required for installations where the wall sleeve extends 4 or more inches into the room or the wall is less than 2 in. (50.8 mm) thick. The minimum clearance between the bottom of the sleeve and the floor is 3--1/4 in. (82.6 mm), and the maximum clearance is 5--1/2 (139.7 mm) inches.

Electrical Subbase Modules

Upgrade non-electrical subbase to a fully electrical subbase by adding an Electrical Subbase module.

The electrical subbase modules have an electrical junction box, receptacle outlet, and cover plate.

Part No: PTAC-REC-230V15-A

Subbase Fuse Kit

Part No.: PTAC--FUSE--15-A

The fuse kit provides in--line over--current protection at the unit when required by NEC (National Electric Code) or local codes.

Subbase Power Disconnect Switch

Part No.: PTAC--SWITCH-A The subbase power disconnect 2--pole switch

provides a recessed power disconnect for the PTAC unit when required by NEC or local codes.

IMPORTANT: The fuse kits and disconnect switch accessories can only be used with Part No. PTAC-SUBBASE-A.

PTAC-REC-230V20-A

PTAC-REC-230V30-A

PTAC-REC-265V15-A

PTAC-REC-265V20-A

PTAC-REC-265V30-A

PTAC-REC-HW-A

PTAC--FUSE--20-A PTAC--FUSE--30-A

IMPORTANT: All standard cord-connected 265-v units will require a field-installed electrical subbase accessory per UL and NEC electrical codes.

Non --Electrical Subbase Assembly

Electrical Subbase Modules

Power Disconnect Switch Module

Subbase Fuse Module

GA

E-TAC

15

FIELD--INSTALLED ACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Leveling Legs

Part No.: LEVELING--LEGS Leveling legs attach easily to the wall sleeve and

offer accurate leveling and support for units without a subbase. Leveling legs are adjustable from 3--1/4 to 5--1/2 inches (82.6 to 139.7 mm).

Hardwire Kit

Part No.: HARDWIRE-KIT-1PK

This accessory hardwire kit provides a permanent connection to the unit. Electrical hard wiring is required when NEC (National Electrical Code) or local codes restrict the use of power cord and plug connections. The hardwire kit mounts on the front

E-TAC

right side of the unit and comes with 36 inches of flexible steel conduit and a Molex connector for easy connect/disconnect.

Conduit Interface Kit

Part No.: CONDUIT-INTF-1PK

The conduit interface accessory kit provides the wire connection to the unit to interface to existing installed conduit.

Extra Long Replacement 265v Power Cord

Part No. PWRCORD-265V-15A

PWRCORD-265V-20A

PWRCORD-265V-30A

The Extra Long Replacement 265v power cord extends 58 inches from bottom of front panel to the plug head. Do not use where prohibited by codes or regulations.

Replacement 265V

Leveling Legs

Hardwire Kit

Conduit Interface Kit

0 2

1918

Extra Long

Power Cord

1

10

9

8

7

6

5

4

3

2

1

17

16

15

14

3

1

2

1

16

FIELD--INSTALLED ACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

THERMOSTATS

Gree’s full line of wall thermostats are designed to enhance every E-TAC application. The TopTech Comfort Series of thermostats consists of programmable and non-programmable air conditioner and heat pump controls. Wall thermostats are simple and easy to use. Wall thermostats provide better temperature and

Non--Programmable Thermostat

Part No.: TT-N-411 (Heat / Cool Models)

This low--voltage, easy--to--use non--programmable thermostat provides maximum guest comfort.

TT-N-421 (Heat Pump Models)

•

Dual Powered – Hardwired or Battery

•

Large Display with Bright Blue Backlight

•

Adjustable Temperature Set Point Limits

•

Non-Volatile Memory Retains User Settings

•

Separate Heating and Cooling Set Points

•

Display Degree F or C Switch

•

Mount to Horizontal Box

•

Adjustable Temperature Differential

Digital Programmable Thermostat

Part No.: TT-P-411 (Heat / Cool Models)

This micro computer controlled, 7--day programmable wall thermostat has enhanced features for both heat pumps and heating/cooling units.

The programmable model includes the non--programmable features plus the following:

Wireless Non-Programmable Thermostat

PartNo.:TT-N-631W(forHeatPump&Heat/Cool Models)

This low voltage wireless wall thermostat provides easy installation and superior performance. Includes

bothwirelesswallthermostatandreceivermoduleand

features:

• Twospeedfancontrol(HighandLowSpeed)

• Universal2H/1CHeatPumpor1H/1CConventional

• PowerLossMemory

• HeatingandCoolingSet-pointLimit

• LargeTemperatureandSet-pointDisplay

• LargeBlueBacklightScreen

TT-P-421 (Heat Pump Models)

•

5-2 Day Separate P

•

Adaptive Recovery Mode (ARM™)

•

Separate Set Point Program Times

•

Temporary P

•

Programmable Extended Hold Mode

•

Meets California Title 24 Guidelines

rogramming

rogram Override

humidity control as they can be placed in an optimal position in the room.

For wiring multiple E-TAC units to one wall

thermostat see the Multiple Wall Thermostat

Wiring section in the installation manual.

Non --Prog rammable Thermostat

Programmable Thermostat

GA

E-TAC

17

FIELD-INSTALLED

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Air Deector

PartNo.:PTAC-DEFLECTOR-A

The PTACAir Deector mounts easily to the units

and directs air up and away from overhanging drapes.

TheAirDeectorsavesenergybyeliminatingtrapped air ow between the window and the curtain while

increasing guest comfort levels and helping to manage mold and mildew in the window area.

Sound Muzzler

PartNo.:PTAC-SOUND-A

Our Sound Muzzler is specically designed and

constructed with environmental friendly materials that

E-TAC

absorbmechanical sound energyandblock offensive

noise from the compressor. This acoustic wrap is weatherproof and easy to install.

ACCESSORIES (CONT.)

Security Door

PartNo.:PTAC-LOCK-A

This key-locking security door kit prevents

unauthorized access to the unit’s heating and cooling

controls andprevents tampering with units in public locationsandinstitutions.Thiseld-installedaccessory includes a control door with lock assembly and two matchingkeys.

E-9000 Remote Control

Part No. 30510092MX

The E-9000 remote control is versatility and allows users to change room temperature and modes from the palm of your hand. The large LCD display and buttons makes it easy-to-understand and easy-to-use.

Air Deector

Sound Muzzler

Security Door

E-9000 Remote Control

18

FIELD--INSTALLED ACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Condensate Drain Kit

Part No.: DRAIN--KIT--1PK This universal drain kit may be used internally or

externally to route condensate to a drainage system. It can be field-installed on any Gree wall sleeve. Although Gree units are designed to dissipate all the condensate generated during normal cooling, there may be times when abnormal conditions cause more condensate than the unit can dissipate. If condensate that drips from the wall sleeve is objectionable, this internal/external drain kit should be installed.

The drain kit may be attached to the exterior right or left side of the wall sleeve for external draining or mounted to the room side of the wall sleeve for internal draining.

A 3 in. (152.4 mm) straight tube and 90˚ curved tube

GA

are supplied to simplify any application (1/2 in. /

12.7 mm OD copper).

IMPORTANT: For internal drains installed in the plastic wall sleeve, the drain must be installed on the flat area of the sleeve. It cannot be installed in the wafer area.

Replacement Filters

Part No.: GA-FILTER-2PK The Gree E-TAC model replacement air filters come

in packages of two (2). The filters save energy by being plugged with dirt and lint. These economical and sturdy filters are interchangeable and may be washed, vacuumed, and reused.

Baffle Kit

Part No.: BAFFLE--KIT--1PK The accessory baffle kit ensures a good seal between

the unit and the exterior grille to prevent air recirculation, which can cause system failure.

The accessory baffle kit is required for applications using unauthorized exterior grille.

preventing the evaporator coils from

A07748

Drain Kit

Replacement FIlters

Baffle Kit

E-TAC

19

FIELD-INSTALLEDACCESSORIES (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

Lateral Duct Kit

Air Knight

TheAirKnightbyTopTechisanairtreatmentsystem not a lter.It drasticallyreduce odors, smoke, mold, fungi,VOC’s(chemical odors) andbacteria foundin

Air Knight Plug-In

PartNo.:RGF-PIP-16-GA.

The Air Knight Plug-In, plugs directly into a wall outletandcanbeusedwithorwithoutitsinternalfan. Becauseithasitsownoutletsaspartoftheunit,youdo

not lose the wall outlet.

E-TAC

Air Knight PTAC

PartNo:TT-AKPTAC

TheAir Knight PTACmounts inside the E-TAC air

discharge stream. The indoor fan delivers air treatment quietly and affectively into the room. The PTAC Air

Knightisneverlostormisplacedsinceitis installed  in the unit.

Part No.: LATERAL-DUCT (Adapter Plenum and Extension)

The accessory lateral duct kit allows one unit to heat or cool two rooms. The kit provides substantial savings for apartments, hotel suites, and office suites by eliminating the need for separate units for every room. The amount of air that can be diverted to an adjoining room is adjustable from 20 to 25 percent.

The lateral duct kit consists of two main components, the plenum and the extension duct. The kit mounts to

the wall sleeve and allows either right or left side ducting. Consider the following when designing a ducted application.

•The maximum extension of the duct length is 4 feet.

•The duct run must be straight and horizontal; no

bends or turns.

•The minimum recommended clearance between the unit and the adjoining room wall is 6 inches.

•You must provide for return air from the adjoining room.

NOTES:

1. Lateral duct kit includes wall register for duct exten-

sion and a molding kit to trim the wall opening.

2. The sleeve should extend a minimum of 3-in. into

the adjacent room to

install mounting brackets.

manyrooms.Airbornebacteriaandmoldreductionis

normally in the 90+ percentile.

Air Knight Plug In

Air Knight PTAC

Lateral Duct Kit

20

DIMENSIONAL DRAWINGS AND INSTALLATION DATA --

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

NEW CONSTRUCTION

Proper building practices must be used when constructing a wall opening to support a PTAC wall sleeve and chassis.

If practices are unknown, consult your local architect or building contractor. Installed wall sleeve must be level from side to side and a quarter bubble to the outside.

A08357

DIMENSIONAL DRAWINGS AND INSTALLATION DATA

VOLTAGE CURRENT DIMENSIONS --- Inches (mm) PLUG TYPE

VOLTS AMPS X

208/230 15 58 (1473) 2.36 (60) 2.44 (62) 3.35 (85) 4 (101) 6--- 15P 6--- 15R

208/230 20 58 (1473) 2.36 (60) 2.44 (62) 3.35 (85) 4 (101) 6--- 20P 6--- 20R

208/230 30 58 (1473) 2.55 (65) 4 (101) 2.63 (67) 3.8 (96) 6--- 30P 6 --- 30R

265 15 15 (381) 1.5 (38.2) 1.46 (37.3) 7 --- 15P 7 --- 15R

265 20 15 (381) 2 (50)

265 30 15 (381) 2.41 (61.3) 7--- 30P 7 --- 30R

DISCHARGE GRILLE

REMOVABLE FRONT PANEL

42"

(1067)

Z

Y

Front View

SUPPLIER 1 SUPPLIER 2 SUPPLIER 1 SUPPLIER 2

ACCESSORY WALL SLEEVE

HINGED CONTROL ACCESS DOOR

Y

208/230V

Accessory Service Cord

X

A08388

Z

NEMA PLUG

2.48 (63.2)

7--- 20P 7 --- 20R

Side View

A08386

NEMA

RECEPTACLE

A07379A

GA

E-TAC

21

DIMENSIONAL DRAWINGS AND INSTALLATION DATA --

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

NEW CONSTRUCTION (CONT.)

WALL SLEEVE MOUNTING DIMENSIONS FOR STANDARD AND ACCESSORY GRILLES

Standard Polymer Non--Insulated Wall Sleeve

Standard Polymer Insulated Wall Sleeve

E-TAC

42 in

(1067 mm)

16 in

(406 mm)

14 7/8 in

(378 mm)

A07633

MAIN STUD

JACK STUD

CRIPPLE

FLOOR

SUB-FLOOR

Framing and Minimum Wall Sleeve Opening

5/8" MIN.

(15.9)

Amounts in ( ) = mm

Standard and Extended Metal Insulated Wall

JACK STUDS

HEADER - 4” X 4” (101.6 X 101.6) OR

(2) 2” X 4” (50.8 X 101.6)

16 1/4”

(412.8)

42 1/8”

(1070.0)

MEASUREMENTS IN ( ) = mm

5/8" MIN.

(15.9)

A07382

42 in

(1067)

Sleeve

16 in (406)

Available in: 14-3/4 in. (375), 18 in. (457), 24 in. (610), 26 in. (660), 28 in. (711)

A07381

GA

1/2" (12.7) MINIMUM

STAMPED OUTDOOR GRILLE

Stamped grille thickness 0.75" (9.4)

NOTE: Dimensions in ( ) are in millimeters

SIDE

Wall Sleeve Mounting (All Models)

22

1/2" (12.7) MINIMUM

ARCHITECTURAL GRILLE

STANDARD MOUNT

ALUMINUM OR PLASTIC

Architectural grille thickness 1.25" (32)

SIDE

A07383A

TYPICAL WALL INSTALLATION

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

5/8”

(15.9 mm)

Typical Wall Sleeve Installation

Typical Curtain Wall Installation (All Models)

MINIMUM 3-1/4” (82.6 mm) ABOVE FLOOR COVERING IF SUBBASE IS USED

A07384

Important Sleeve Installation Considerations:

Wall Sleeve should be pitched 1/4 bubble

•

to the outside for condensate drainage.

• The sleeve should be caulked on all sides,

including both inside and outside the building.

•

• For all applications with an accessory

re than 4 in. (101 mm) of wall sleeve

If mo projects into the roo or leveling legs must be used for support.

m, an accessory subbase

subbase, wall sleeve must extend 3--1/4 in. (82.6 mm) minimum into room and must be 3--1/4 in. (82.6 mm) minimum to 5--1/2 in. (139.7 mm) maximum above floor (including

NOTES:

carpeting) to allow for proper fit of subbase.

• For applications where the wall sleeve is

mounte building (or recessed in), Gree recommends a field--supplied drip edge be installed to prevent water infiltration into the building.

• Insulated wall sleeves should be considered

for superior sound absorption, to reduce heat loss and to prevent sleeve sweating, a condition that can occur when the outside temperature is cold and the indoor conditions are warm and humid.

1. Sleeve may be flush mounted to floor, but front panel may have to be notched to accommodate service cord.

2. If more than4in. (101.6 mm) of sleeve projects

d flush to the exterior of the

into room, an accessory subbase or leveling legs must be used for support.

3. For walls 2 in. (50.8 mm) thick or less, an accessory subbase must be used for support.

4. Caulk around sleeve on both indoor and outdoor sides.

A07385

E-TAC

23

DIMENSIONAL DRAWINGS AND INSTALLATION --

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• R

apid servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

NEW CONSTRUCTION (CONT.)

MINIMUM CLEARANCE FOR INDOOR AND OUTDOOR DISCHARGE AIR

E-TAC

Indoor and Outdoor Discharge Air

GRILLE MOUNTING HOLES

2 3/8”

(60.3)

15” (381.0 mm) MINIMUM DISTANCE FROM

FRONT PANEL TO OBJECTS IN ROOM

36" (914.4 mm) MINIMUM DISTANCE FROM

SLEEVE TO BUILDING WALLS,

SHRUBS, etc.

Circulation

WALL SLEEVE

CONDENSATE OVERFLOW HOLES

WALL SLEEVE-(2) DRAIN LOCATIONS

(OUTSIDE)

Back of Pol ymer Wall Sleeve

!

EQUIPMENT OPERATION HAZARD

Failure to follow this caution may result in equipment damage or improper operation. Blocking indoor or outdoor discharge air could cause premature failure of unit.

OUTDOOR VIEW

2 3/8” (60.3)

CAUTION

A07386

GRILLE MOUNTING HOLES

GA

A07387

24

DIMENSIONAL DRAWINGS AND INSTALLATION DATA --

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

NEW CONSTRUCTION (CONT.)

TYPICAL SUBBASE INSTALLATION

0’-0 7/8”

OUTSIDE

GA

NOTES:

WALL

SEE

NOTES

SIDE

ACCESSORY DRAIN (EXTERNAL OR INTERNAL)

1. Accessory subbase is required for applications where:

2. For all applications with an accessory subbase:

- Wall sleeve extends 4 inches (101.6 mm) or more into the room.

- Wall thickness is less than 2 inches (50.8 mm).

- All 265-v cord-connected applications.

-

Wall sleeve must extend 4 in. (101.6 mm) into the room and 3-1/4 in. (82.6 mm)minimum above the floor

-

Subbase height is adjustable from 3-1/4 in. (82.6 mm) to 5-1/2 in. (139.7 mm) maximum above floor (including carpeting).

Refer to wall sleeve installation instructions.

(22)

SUBBASE LEVELING BOLTS

SUBBASE ACCESS

0’-3 1/4” MIN. (83) 0’-5 1/2” MAX. (140)

A07389

E-TAC

25

TYPICAL LATERAL DUCT INSTALLATION

WALL REGISTER

WALL MOLDING

3’-11 1/2” (1206.5)

MAX.

*Only one Lateral Duct Extension may be installed per

unit. Lateral duct extensions may be installed on either side of the unit.

LATERAL DUCT EXTENSION

REVERSIBLE AIR GRILLE

3’-8”

(117.6)

PLENUM

3’-11 1/2” (1206.5)

MAX.

END CAP

ALTERNATE EXTENSION POSITION*

NOTE: For all applications with an accessory lateral duct, sleeve must extend into the room a minimum of 3 inches. In applications where the sleeve will not extend a minimum of 3 in., the lateral duct mounting brackets will need to be mounted on the sleeve prior to installation to the wall.

26

WALL THERMOSTAT CONNECTIONS

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

TYPICAL WALL THERMOSTAT

NOTES:

1. Use terminal "O" for heat pump connection only.

2. Terminal "C" (common) is typically only required for digital thermostats.

TERMINAL BLOCK

E-TAC

Control Box Wire Terminal for

Wall Thermostat Models

R

W

Y

O

GH

GL

C

Management

Common

See Note 1

See Note 2

Energy

(24VAC in)

A07059

Energy Management

Terminal Connections

Terminal Connector Removal and Replacem ent

R W Y O Gh Gl C

A07073

Wall Thermostat

Terminal Connections

A07634

GA

THERMOSTAT WIRE ROUTING

(UNDER SLEEVE, BEHIND FRONT PANEL)

Terminal Wire Routing

A07074

NOTE: Thermostat wire is field su pp 18 to 20 gauge solid thermostat wire. Thermostat wire should always be routed around or under, NEVER through, the wall sleeve. The wire should then be routed behind the front panel to the easily accessible terminal connector.

27

lied. Recommended wire gauge is

PERFORMANCE AND ELECTRICAL DATA

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

208/230V HEAT/COOL MODELS

E-TAC

MODEL NUMBER

ETAC-07HC230V15A-A ETAC-07HC230V20A-A ETAC-09HC230V15A-A ETAC-09HC230V20A-A ETAC-12HC230V15A-A ETAC-12HC230V20A-A ETAC-12HC230V30A-A ETAC-15HC230V20A-A ETAC-15HC230V30A-A

*Rated in accordance with ARI Standard 380-93. LEGEND

†Coefficient of Performance (COP) at 47 F outdoor ambient temperature

**Electric resistance heater power and fan motor power.

MODEL NUMBER

RECEPTACLE

NEMA CONFIGURATION6-15R 6-20R6-30R

RATED VOLTS 250 250 250

TIME-DELAY TYPE FUSE 15 20

(or HACR Circuit Breaker)

Cooling

7,600/7,700 N/A5,200/6,800 1.6/2.0 12.2/12.0NA 126 A 7,600/7,700 N/A8,300/10,200 2.4/3.0 12.2/12.0NA 126 B 8,800/9,000 N/A5,200/6,800 1.6/2.0 11.4/11.3NA 128 A

8,800/9,000 N/A8,300/10,200 2.4/3.0 11.4/11.3NA 128 B 11,800/12,000 N/A5,200/6,800 1.6/2.0 10.5/10.7NA 132 A 11,800/12,000 N/A8,300/10,200 2.4/3.0 10.5/10.7NA 132 B 11,800/12,000 N/A 13,900/17,0004.1/5.0 10.5/10.7NA 132 C 14,600/15,000 N/A8,300/10,200 2.4/3.09.7/9.8 NA 141 B 14,600/15,000 N/A 13,900/17,0004.1/5.0 9.7/9.8NA 141 C

POWER

FACTOR (%)

VOLTAGE

RANGE

187-253

CAPACITY* (Btuh)

Heating

Rev. Cyc. Electric

Horsepower

97% 0.024 0.42 280/294 18.01.7 84% 97% 0.024 0.42 280/294 18.01.7 84% 99% 0.028 0.36 280/312 21.52.1 81% 99% 0.028 0.36 280/312 21.52.1 81% 99% 0.031 0.36 290/330 26.82.7 67% 99% 0.031 0.36 290/330 26.82.7 67% 99% 0.031 0.36 290/330 26.82.7 67% 98% 0.031 0.2 320/340 38.13.5 65% 98% 0.031 0.2 320/340 38.13.5 65%

CoolingHeatingCoolingHeating**

620/640 1,635/2,000 3.1/2.87.9/8.9 15 11.1 620/640 2,452/3,000 3.1/2.8 12.2/13.220 16.5 770/800 1,635/2,000 3.9/3.77.9/8.9 15 11.1

770/800 2,452/3,000 3.9/3.7 12.2/13.220 16.5 1,120/1,120 1,635/2,000 5.7/5.17.9/8.9 15 11.1 1,120/1,120 2,452/3,000 5.7/5.1 12.2/13.220 16.5 1,120/1,120 4,087/5,000 5.7/5.1 20.5/21.530 27.2 1,510/1,530 2,452/3,000 7.5/6.7 12.2/13.220 16.5 1,510/1,530 4,087/5,000 7.5/6.7 20.5/21.530 27.2

AMPS

INDOOR FAN

Full Load

Amps

AB

HEATER

CFM HI

Speed

KW

EER

R-410A

CHARGE

(oz)

AMPSWATTS

COP†

DEHUMIDIFI-

CACTION (Pints/Hr)

MAX FUSE

SIZE (Amps)

EER — Energy Efficiency Ratio COP — Coefficient of performance CFM — Cubic feet per minute

CHASSIS

SHIP WT. (lbs)

SENSIBLE

HEAT

FACTOR

MIN. CIRCUIT

AMP.

C

3015 20

30

RECEP-

TACLE

TYPE

E-TAC

28

PERFORMANCE AND ELECTRICAL DATA (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

265V HEAT/COOL MODELS

1E 1F

.L

E-TAC

MODEL NUMBER

ETAC-07HC265V20B-A ETAC-09HC265V20A-A ETAC-12HC265V20A-A ETAC-12HC265V30A-A ETAC-15HC265V20A-A ETAC-15HC265V30A-A

MODEL NUMBER

ETAC-07HC265V20B-A ETAC-09HC265V20A-A ETAC-12HC265V20A-A ETAC-12HC265V30A-A ETAC-15HC265V20A-A ETAC-15HC265V30A-A

MODEL NUMBER

ETAC-07HC265V20B-A ETAC-09HC265V20A-A ETAC-12HC265V20A-A ETAC-12HC265V30A-A ETAC-15HC265V20A-A ETAC-15HC265V30A-A

*Rated in accordance with ARI Standard 380-93

†Coeffic

**Electric resistance heater power and fan motor power.

NEMA CONFIGURATION 7-15R 7-20R 7-30R

TIME-DELAY TYPE FUSE152030

(or HACR Circuit Breaker)

12,000 N/A10,200 3.0 10.7NA132 E 12,000 N/A17,000 5.0 10.7NA132 F 15,000 N/A10,200 3.09.8 NA 14 15,000 N/A17,000 5.09.8 NA 14

POWER

FACTOR (%)

VOLTAGE

RANGE

239-292

ie

nt of Performance (COP) at 47 F outdoor ambient temperature

RECEPTACLE

RATED VOLTS 277 277 277

CAPACITY* (Btuh)

Heating

Rev. Cyc. Electric

7,700 N/A10,200 3.0 12.0NA124 E 9,000 N/A10,200 3.0 11.3NA126 E

Horsepower

97% 0.0280.4 294 24.71.7 84% 99% 0.0280.2 300 19.42.1 81% 99% 0.0310.2 310 25.02.7 67% 99% 0.0310.2 310 25.02.7 67% 98% 0.0310.2 320 40.23.5 65% 98% 0.0310.2 320 40.23.5 65%

WATTS AMPS

CoolingHeatingCoolingHeating**

640 3,000 2.4 11.320 16.5

800 3,000 3.2 11.320 16.5 1,1203,000 4.6 11.320 16.5 1,1205,000 4.6 18.930 27.2 1,1203,000 5.9 11.320 16.5 1,5305,000 5.9 18.930 27.2

AMPS

INDOOR FAN

Full Load

Amps

DEF

15 20 30

HEATER

CFM HI

KW

Speed

EERCOP†

R-410A

CHARGE

(oz)

CHASSIS

SHIP WT. (lbs)

DEHUMIDIFI-

CACTION (Pints/Hr)

MAX FUSE

SIZE (Amps)

EER — Energy Efficiency Ratio COP — Coefficient of performance CFM — Cubic feet per minute

SENSIBLE

HEAT

FACTOR

MIN. CIRCUIT

AMP.

EGEND

RECEP-

TACLE

TYPECooling

E-TAC

29

PERFORMANCE AND ELECTRICAL DATA

208/230V HEAT PUMP MODELS

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

MODEL NUMBER

ETAC-07HP230V15B-A 7,600/7,700 6,100/6,300 5,200/6,8001.6/2.0 12.2/12.03.4/3.4 126 A ETAC-07HP230V20B-A 7,600/7,700 6,100/6,300 8,300/10,2002.4/3.0 12.2/12.03.4/3.4 126 B ETAC-09HP230V15B-A 8,800/9,000 7,900/8,100 5,200/6,8001.6/2.0 11.4/11.33.3/3.3 130 A ETAC-09HP230V20B-A 8,800/9,000 7,900/8,100 8,300/10,2002.4/3.0 11.4/11.33.3/3.3 130 B ETAC-12HP230V15A-A 11,800/12,000 10,500/10,700 5,200/6,8001.6/2.0 10.5/10.73.1/3.1 135 A ETAC-12HP230V20A-A 11,800/12,000 10,500/10,700 8,300/10,2002.4/3.0 10.5/10.73.1/3.1 135 B ETAC-12HP230V30A-A 11,800/12,000 10,500/10,700 13,900/17,0004.1/5.0 10.5/10.73.1/3.1 135 C ETAC-15HP230V20B-A 14200/14,500 13,000/13,300 8,300/10,2002.4/3.0 9.7/9.83.0/3.0 143 B ETAC-15HP230V30B-A 14200/14,500 13,000/13,300 13,900/17,0004.1/5.0 9.7/9.83.0/3.0 143 C

CAPACITY* (Btuh)

Heating

Rev. Cyc. Electric

E-TAC

MODEL NUMBER

ETAC-07HP230V15B-A 97% 0.028 0.42 280/29422.91.7 84% ETAC-07HP230V20B-A 97% 0.028 0.42 280/29422.91.7 84% ETAC-09HP230V15B-A 99% 0.028 0.36 280/31225.02.1 81% ETAC-09HP230V20B-A 99% 0.028 0.36 280/31225.02.1 81% ETAC-12HP230V15A-A 99% 0.031 0.36 290/33026.82.7 67% ETAC-12HP230V20A-A 99% 0.031 0.36 290/33026.82.7 67% ETAC-12HP230V30A-A 99% 0.031 0.36 290/33026.82.7 67% ETAC-15HP230V20B-A 98% 0.031 0.8 320/34138.13.2 65% ETAC-15HP230V30B-A 98% 0.031 0.8 320/34138.13.2 65%

MODEL NUMBER

ETAC-07HP230V15B-A 620/6401,635/2,0003.0/2.8 7.9/8.91511.1 ETAC-07HP230V20B-A 620/6402,452/3,0003.0/2.8 12.2/13.22016.5 ETAC-09HP230V15B-A 770/8001,635/2,0003.9/3.7 7.9/8.91511.1 ETAC-09HP230V20B-A 770/8002,452/3,0003.9/3.7 12.2/13.22016.5 ETAC-12HP230V15A-A 1,120/1,120 1,635/2,0005.7/5.1 7.9/8.91511.1 ETAC-12HP230V20A-A 1,120/1,120 2,452/3,0005.7/5.1 12.2/13.22016.5 ETAC-12HP230V30A-A 1,120/1,120 4,087/5,0005.7/5.1 20.5/21.53027.2 ETAC-15HP230V20B-A 1,460/1,480 2,452/3,0007.5/6.7 12.2/13.22016.5 ETAC-15HP230V30B-A 1,460/1,480 4,087/5,0007.5/6.7 20.5/21.53027.2

*Rated in accordance with ARI Standard 380-93. LEGEND

†Coefficient of Performance (COP) at 47 F outdoor ambient temperature

**Electric resistance heater power and fan motor power.

POWER

FACTOR (%)

VOLTAGE

RANGE

187-253

Horsepower

WATTSAMPS

CoolingHeating CoolingHeating**

INDOOR FAN

Full Load

Amps

HEATER

CFM HI

Speed

RECEPTACLE

ABC

NEMA CONFIGURATION6-15R 6-20R 6-30R

TIME-DELAY TYPE FUSE 15 20 30

(or HACR Circuit Breaker)

RATED VOLTS250 250250

AMPS

15 20 30

KW

EERCOP†

CHASSIS SHIP WT.

(lbs)

RECEP-

TACLE

TYPECooling

R-410A

CHARGE

(oz)

DEHUMIDIFI-

CACTION (Pints/Hr)

SENSIBLE

HEAT

FACTOR

MAX FUSE

SIZE (Amps)

MIN. CIRCUIT

AMP.

EER — Energy Efficiency Ratio COP — Coefficient of performance CFM — Cubic feet per minute

30

265V HEAT PUMP MODELS

4E 1E 5E 5F

.L

PERFORMANCE AND ELECTRICAL DATA (CONT.)

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

MODEL NUMBER

ETAC-07HP265V20B-A ETAC-09HP265V20A-A ETAC-12HP265V20A-A ETAC-12HP265V30A-A ETAC-15HP265V20B-A ETAC-15HP265V30B-A

MODEL NUMBER

ETAC-07HP265V20B-A ETAC-09HP265V20A-A ETAC-12HP265V20A-A ETAC-12HP265V30A-A ETAC-15HP265V20B-A ETAC-15HP265V30B-A

MODEL NUMBER

ETAC-07HP265V20B-A ETAC-09HP265V20A-A ETAC-12HP265V20A-A ETAC-12HP265V30A-A ETAC-15HP265V20B-A ETAC-15HP265V30B-A

*Rated in accordance with ARI Standard 380-93

†Coeffic

**Electric resistance heater power and fan motor power.

12,000 10,700 10,200 3.0 10.73.1 13 12,000 10,700 17,000 5.0 10.73.1 13 14,500 13,300 10,200 3.09.8 3.0140 E 14,500 13,300 17,000 5.09.8 3.0140 F

POWER

FACTOR (%)

VOLTAGE

RANGE

239-292

ient of Performance (COP) at 47 F outdoor ambient temperature

RECEPTACLE

CAPACITY* (Btuh)

Heating

Rev. Cyc. Electric

7,700 6,30010,200 3.0 12.03.4 9,300 8,10010,200 3.0 11.33.3 13

INDOOR FAN

Horsepower

97% 0.0280.4 294 24.71.7 84% 99% 0.0280.2 300 23.62.1 81% 99% 0.0310.2 310 27.22.7 67% 99% 0.0310.2 310 27.22.7 67% 98% 0.0310.6 341 36.32.8 65% 98% 0.0310.6 341 36.32.8 65%

CoolingHeatingCoolingHeating**

640 3,000 2.4 11.3

825 3,000 3.4 11.320 16.5 1,1203,000 4.6 11.320 16.5 1,1205,000 4.6 18.930 27.2 1,4803,000 5.8 11.320 16.5 1,4805,000 5.8 18.930 27.2

Full Load

Amps

WATTS AMPS

DEF

NEMA CONFIGURATION 7-15R 7-20R 7-30R

RATED VOLTS 277 277 277

TIME-DELAY TYPE FUSE152030

(or HACR Circuit Breaker)

AMPS

15 20 30

HEATER

KW

EERCOP†

R-410A

CFM HI

Speed

CHARGE

(oz)

DEHUMIDIFI-

CACTION (Pints/Hr)

MAX FUSE

SIZE (Amps)

20 16.5

EER — Energy Efficiency Ratio COP — Coefficient of performance

— Cubic feet per minute

CFM

CHASSIS

SHIP WT. (lbs)

12

SENSIBLE

HEAT

FACTOR

MIN. CIRCUIT

AMP.

EGEND

RECEP-

TACLE

TYPECooling

E-TAC

31

ALL 7,000 NORMINAL BTUH MODELS

ALL 9,000 NORMINAL BTUH MODELS

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

E-TAC

EXPANDED RATING DATA

COOLING PERFORMANCE - HEAT/COOL MODELS

Evaporator entering air temp (D.B.) = 80 deg F Evaporator entering air temp (D.B.) = 80 deg F

TEMP (DEG F) AIR

ENT COND (40%RH)

BtuH 8062 8709 9055 BtuH 9423 10179 10584 Kw 536 531 522 Kw 670 663 653 Amps 2.4 2.3 2.3 Amps 3.1 3.1 3.1 SHR 0.96 0.72 0.53 SHR 0.89 0.66 0.49 BtuH 7500 8131 8624 BtuH 8766 9504 10080 Kw 582 575 569 Kw 727 718 711 Amps 2.5 2.5 2.5 Amps 3.3 3.3 3.3 SHR 0.98 0.74 0.54 SHR 0.91 0.69 0.5 BtuH 6815 7700 8285 BtuH 7965 9000 9684 Kw 640 640 640 Kw 800 800 800 Amps 2.8 2.8 2.8 Amps 3.7 3.7 3.7 SHR 0.99 0.77 0.54 SHR 0.91 0.71 0.5 BtuH 6075 6892 7762 BtuH 7101 8055 9072 Kw 693 691 692 Kw 866 864 865 Amps 3.0 3.0 3.0 Amps 4.0 4.0 4.0 SHR 0.99 0.81 0.55 SHR 0.92 0.75 0.51 BtuH 5251 5944 6907 B Kw 758 755 755 Kw 947 943 943 Amps 3.3 3.3 3.3 Amps 4.4 4.3 4.3 SHR 0.99 0.87 0.58 SHR 0.91 0.8 0.54

Evaporator entering air temp (D.B.) = 80 deg F Evaporator entering air temp (D.B.) = 80 deg F

TEMP (DEG F) AIR

ENT COND (40%RH)

BtuH 12564 13572 14112 BtuH 15705 16965 17640 Kw 939 928 914 Kw 1282 1268 1248 Amps 4.3 4.2 4.2 Amps 5.6 5.6 5.5 SHR 0.89 0.66 0.49 SHR 0.85 0.63 0.47 BtuH 11688 12672 13440 BtuH 14610 15840 16800 Kw 1018 1006 996 Kw 1391 1374 1360

mps 4.6 4.6 4.5 Amps 6 6 6

A SHR 0.91 0.69 0.5 SHR 0.87 0.66 0.48 BtuH 10620 12000 12912 BtuH 13275 15000 16140 Kw 1120 1120 1120 Kw 1530 1530 1530 Amps 5.1 5.1 5.1 Amps 6.7 6.7 6.7 SHR 0.91 0.71 0.5 SHR 0.87 0.68 0.48 BtuH 9468 10740 12096 BtuH 11835 13425 15120 Kw 1213 1210 1211 Kw 1657 1652 1654 Amps 5.5 5.5 5.5 Amps 7.2 7.2 7.2 SHR 0.92 0.75 0.51 SHR 0.88 0.72 0.49 BtuH 8184 9264 10764 BtuH 10230 11580 13455 Kw 1326 1320 1320 Kw 1812 1804 1804 Amps 666 Amps 7.9 7.9 7.9 SHR 0.91 0.8 0.54 SHR 0.87 0.77 0.51

Temp EVAP AIR-EWB (DEG F)

LEGEND EWB - Entering Wet Bulb D.B. Dry Bulb AMP - Total Current Kw - Total Power BtuH - Total Cooling Capacity

SHR-

Senable Heating Ratio-

TEMP (DEG F) AIR

ENT COND (40%RH)

TEMP (DEG F) AIR

ENT COND (40%RH)

5757

5858

5959

501501

tuH 6138 6948 8073

011011

5757

5858

5959

501501

011011

Temp EVAP AIR-EWB (DEG F)

277626277626

SLEDOMHUTBLANIMRON000,51LLASLEDOMHUTBLANIMRON000,21LLA

277626277626

E-TAC

32

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

E-TAC

EXPANDED RATING DATA

COOLING PERFORMANCE - HEAT PUMP MODELS

ALL 7,000 NORMINAL BTUH MODELS ALL 9,000 NORMINAL BTUH MODELS

Evaporator entering air temp (D.B.) = 80 deg F Evaporator entering air temp (D.B.) = 80 deg F

TEMP (DEG F) AIR

ENT COND (40%RH)

BtuH 8062 8709 9055 BtuH 9423 10179 10584 Kw 536 531 522 Kw 670 663 653

75

Amps 2.4 2.3 2.3 Amps 3.1 3.1 3.1 SHR 0.96 0.72 0.53 SHR 0.89 0.66 0.49 BtuH 7500 8131 8624 BtuH 8766 9504 10080 Kw 582 575 569 Kw 727 718 711

85

Amps 2.5 2.5 2.5 Amps 3.3 3.3 3.3 SHR 0.98 0.74 0.54 SHR 0.91 0.69 0.5 BtuH 6815 7700 8285 BtuH 7965 9000 9684 Kw 640 640 640 Kw 800 800 800

95

Amps 2.8 2.8 2.8 A SHR 0.99 0.77 0.54 SHR 0.91 0.71 0.5 BtuH 6075 6892 7762 BtuH 7101 8055 9072 Kw 693 691 692 Kw 866 864 865

105

Amps 3.0 3.0 3.0 Amps 4.0 4.0 4.0 SHR 0.99 0.81 0.55 SHR 0.92 0.75 0.51 BtuH 5251 5944 6907 BtuH 6138 6948 8073 Kw 758 755 755 Kw 947 943 943

110

Amps 3.3 3.3 3.3 Amps 4.4 4.3 4.3 SHR 0.99 0.87 0.58 SHR 0.91 0.8 0.54

ALL 12,000 NORMINAL BTUH MODELS ALL 15,000 NORMINAL BTUH MODELS

Evaporator entering air temp (D.B.) = 80 deg F Evaporator entering air temp (D.B.) = 80 deg F

TEMP (DEG F) AIR

ENT COND (40%RH)

BtuH 12564 13572 14112 BtuH 15182 16400 17052 Kw 939 928 914 Kw 1240 1227 1208 Amps 4.3 4.2 4.2 Amp SHR 0.89 0.66 0.49 SHR 0.88 0.65 0.48 BtuH 11688 12672 13440 BtuH 14123 15312 16240 Kw 1018 1006 996 Kw 1345 1329 1316 Amps 4.6 4.6 4.5 Amps 5.9 5.9 5.9 SHR 0.91 0.69 0.5 SHR 0.89 0.68 0.49 BtuH 10620 12000 12912 BtuH 12833 14500 15602 Kw 1120 1120 1120 Kw 1480 1480 1480 Amps 5.1 5.1 5.1 Amps 6.6 6.6 6.5 SHR 0.91 0.71 0.5 SHR 0.9 0.7 0.49 BtuH 9468 10740 12096 BtuH 11441 12978 14616 Kw 1213 1210 1211 Kw 1603 1598 1600 Amps 5.5 5.5 5.5 Amps 7.1 7.1 7.1 SHR 0.92 0.75 0.51 SHR 0.9 0.74 0.5 BtuH 8184 9264 10764 BtuH 9889 11194 13007 Kw 1326 1320 1320 Kw 1752 1745 1745 Amps 6 6 6 Amps 7.7 7.7 7.7 SHR 0.91 0.8 0.54 SHR 0.9 0.79 0.53

Temp EVAP AIR-EWB (DEG F)

LEGEND EWB - Entering Wet Bulb D.B. Dry Bulb AMP - Total Current Kw - Total Power BtuH - Total Cooling Capacity RH - Relative Humidity

SHR - Senable Heating Ratio

TEMP (DEG F) AIR

ENT COND (40%RH)

TEMP (DEG F) AIR

ENT COND (40%RH)

75

85

95

mps 3.7 3.7

105

110

5757

5858

5959

501501

011011

Temp EVAP AIR-EWB (DEG F)

s 5.5 5.5

277626277626

3.7

277626277626

5.4

GA

E-TAC

33

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

EXPANDED RATING DATA

HEAT PUMP HEATING PERFORMANCE

NORNIMAL BtuH

SIZE

BtuH 5250 5540 6300 6900 7620

7,000

9,000

12,000

15,000

GA

E-TAC

INDOOR FAN PERFORMANCE DATA

7000 BTUH Heat / Cool 7000 BTUH Heat Pump

9000 BTUH Heat / Cool 9000 BTUH Heat Pump

12,000 BTUH Heat / Cool 12,000 BTUH Heat Pump

15,000 BTUH Heat / Cool

15,000 BTUH Heat Pump

15,000 BTUH Heat / Cool 15,000 BTUH Heat Pump

Kw 509 518 540 549 580 Amps 2.3 2.4 2.4 2.5 2.6 BtuH 6005 6399 8100 8647 9245 Kw 647 656 720 725 735 Amps 3.3 3.3 3.4 3.4 3.5 BtuH 7726 8531 10700 11278 12234 Kw 883 917 1010 1039 1073 Amps 4 4.1 4.5 4.7 4.9 BtuH 10530 10850 13300 14550 15940 Kw 1197 1212 1300 1377 1439 Amps 5.3 5.4 5.8 6.1 6.3

Based on 70 Deg F Indoor Temperature

D.B. - Dry Bulb AMP - Total current Kw - Total Power BtuH - Total Cooling Capacity RH - Relative Humidity

Model Voltage

OUTDOOR TEMP D.B (DEG F)

37 42 47 52 57

LEGEND

Dry Coil (CFM)*

Low Medium High Low Medium High

208 235 250 270 220 235 250

230 260 280 300 240 260 280

265 260 280 300 240 260 280

208 235 250 270 220 235 250

230 260 280 300 240 260 280

265 260 280 300 240 260 280

208 245 260 280 225 240 260

230 270 290 310 250 270 290

265 270 290 310 250 270 290

208 270 290 305 250 270 290

230 300 320 340 280 300 320

265 300 320 340 280 300 320

Wet Coil (CFM)*

E-TAC

*

Dry CFM = INDOOR AIRFLOW WITH DRY INDOOR COIL Wet CFM = INDOOR AIRFLOW WITH WET INDOOR COIL

34

CFM = Cubic Feet per Minute

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purcha

se

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime: complete cha

ssis can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree GA series PTAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wa

ll slee

ve

extensi

on(see accessor

y

Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree GA Series will meet your needs.

The Gree GA series Packaged Terminal Air Conditioning (PTAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purcha

se

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime: complete cha

ssis can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Re

trofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purcha

se

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime: complete cha

ssis can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Re

trofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

GA

HEAT / COOL

HEAT PUMP

Indoor SoundEstimatingTable (Sound Pressure)

NOMINAL SIZES (dBA) NOMINAL SIZES (BELS)

HEAT PUMP HEAT / COOL

Volts

6.2

12000 15000

9000

7000

52.6 5.5 5.9 5.9 6.0 5.6 6.0 6.1 6.2

52.0

48.3

52.1 46.7

52.9

48.1 46.7

208

53.1 53.2 5.7 6.1 6.1 6.1 5.7 6.1 6.2 6.2

51.1

48.4

53.0

54.4

49.5 48.8

230

6.0 5.8 6.2 6.2 6.2

6.0

51.9 6.1 5.9

52.4

52.0

50.0 47.9

50.9 48.7 50.3

265

15000

5.8 5.9 5.9 5.6 5.9 6.1 6.1

9000 12000

5.5

7000

51.6 52.5

51.7 51.2 6.1 5.8 6.0 6.0 5.8 6.2 6.2 6.1

52.8 52.8 5.7 6.0 6.1 6.1 5.7 6.1 6.2

12000 15000

51.6

50.6

47.8

47.6

47.4

7000 9000

51.4 46.0

52.2

52.4

47.8 46.3

208

48.9 47.8 54.1

230

50.0

49.9

50.7 47.9

265

15000

12000

7000 9000

6.1 5.8 6.1 6.2 6.3

6.1

52.5 53.0 5.6 5.9 6.0 6.0 5.6 5.9 6.0 6.2

53.5 53.7 5.8 6.1

49.3

51.5

52.9 47.2

53.5 48.9

54.4

53.8

49.1

48.6 47.4

50.0

208

230

6.2 5.8 6.2 6.3 6.3

6.1

52.8 52.9 6.1 5.9

52.3

52.0 48.3

51.2

51.1 49.5

265

5.5

5.3

5.5 4.7 5.1

5.3

46.0 4.7 5.1

47.0

40.4

46.2 38.8

47.0

41.0

39.6

208

5.7 4.9 5.3 5.5 5.8

5.5

48.1 47.4 5.0 5.3

44.0

48.6 41.9

48.3

42.6 44.3

230

5.7

5.4

5.2

5.6

5.4

5.1 5.1

43.5 46.6

41.9

46.0 41.9

43.6

41.1 41.4

265

5.7

5.5

5.5 5.0 5.4

5.3

47.1 4.9 4.9

48.3

42.2

48.2 41.3

48.1

41.9 43.1

208

5.9

6.0

5.9

5.8

5.4

5.6

5.7

5.6

5.5

5.1

5.8

5.7 5.4 5.5

5.6

5.4 5.6

5.2 5.4

48.0 5.3

45.6

49.1 48.2

45.2

45.1

49.7 43.8

47.0 43.5

49.1

42.7 43.9 45.6

44.5 45.8

230

265

5.7

5.3

5.6

5.2

5.3

5.4

5.6

5.9

5.7

5.5

5.6 5.7

5.4 5.6

5.1 5.2

5.4

48.2

49.2

49.8 49.0

47.4 50.2

46.2

46.3

43.9

49.8 43.0

49.0 44.4

50.6 45.4

49.2

43.6 44.5

45.7 46.5 49.7

44.1 45.6 47.1

230

265

208

5.7

5.6

5.5 5.8

5.5

5.4

5.6

5.2 5.3 5.4

5.3 5.3 5.4

6.0

6.2

6.1

6.1 6.1

6.2 6.1

5.9 5.9

5.5

47.0 47.8

40.6

40.5

52.1

47.5 47.6 53.5

208

5.9 6.0 6.1 5.4

5.5

5.7

5.9

49.1

48.1 49.2

43.5 47.0

44.0

43.2

42.4 48.3

42.4

52.8

51.0 42.6

53.4 43.2

54.2

49.5 56.4

49.0 52.2 50.7

48.3 48.1

49.5

230

265

208

6.0

5.6 5.6 5.7

6.2

49.1 50.2 5.7 6.1 6.1

45.2

53.6 44.9

49.6 55.5

50.1

230

6.3 6.1 6.0 5.4 5.6 5.6 5.8

6.0

48.6 48.5

45.5

50.0 43.6

52.5 50.9

49.8

265

6.0

49.2 50.2 5.6 6.0 6.1 6.1 5.5 5.6 5.6

43.7

53.3 43.8

54.0

48.5 48.4

208

6.2 6.2 6.2 5.6 5.7 5.7 6.1

5.8

49.8 50.8

46.1

53.8 46.2

49.8 54.7

50.3

230

6.0

47.9 50.4 6.0 6.3 6.2 6.2 5.5 5.7 5.8

47.2

45.0

52.0

52.7 51.5

50.2

265

GA

E-TAC

INDOOR SOUND POWER DATA

Mode

Operating

Low Cool

Cool

Medium

High Cool

Low Fan

Fan

Medium

35

High Fan

Low Heat

Heat

Medium

High Heat

See notes on page 36

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HV

AC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime

: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Frie

drich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HV

AC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime

: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Frie

drich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

7.3

GA

E-TAC

Outdoor Sound Estimating Table (dBA and BELS)

NOMINAL SIZES (dBA) NOMINAL SIZES (BELS)

HEAT PUMP HEAT / COOL HEAT PUMP HEAT / COOL

Volts

7000 9000 12000 15000

65.7 66.1 6.9 7.1 7.2 7.3 7.0 7.1 7.2 7.3

63.0

62.9

66.4

63.3 62.7 65.7

230

62.5 63.3 7.0 7.1 7.3 7.3 6.9 7.2 7.3 7.3

62.2

59.4

59.9 60.7 62.9 63.0

265

7.1 6.8 6.9 7.0 7.2

7.0

65.1 6.7 6.9

64.7

60.4

61.6

65.2

61.7 61.2 64.7

208

15000

9000 12000

7000

64.8 65.1 6.7 69 7.0 7.2 6.8 6.9 7.0 7.2

12000 15000

60.4

61.5

7000 9000

65.4

15000

64.5

12000

61.9 61.0

7000 9000

208

65.9 66.0 6.9 7.1 7.2 7.3 7.0 7.1 7.2 7.3

63.2

66.4

65.7

63.5 63.0

230

7.3 6.9 7.2 7.3 7.3

7.3

62.5 63.3 7.0 7.1

62.2

63.0 59.4

59.9 60.7 62.9

265

7.2 6.8 6.9 7.0 7.2

7.1

65.1 6.7 6.9

64.6

60.4

65.6 61.7

65.2

61.8 61.1

208

--- --- --- ---

7.2

--- --- --- ---

7.3 7.0 7.1

7.3 6.9 7.2 7.3 7.3

7.2

7.3

7.1

6.8 7.0

65.8 6.9 7.1

62.5 63.3 7.0 7.1

66.0

--- --- --- --- --- --- --- ---

62.2

63.0

63.5

--- --- --- --- --- --- --- ---

66.6

63.0 59.4

66.4

68.1

66.0

62.9

62.3

62.9

62.7

63.3

59.9 60.7

230

265

208

--- --- --- ---

7.4 --- --- --- --- --- --- --- ---

7.3

7.0 7.2

--- --- --- --- --- --- --- ---

--- --- --- ---

67.6

70.0

64.6 64.5

230

--- --- --- ---

7.4

7.3

7.1 7.2

--- --- --- --- --- --- --- ---

64.0

63.2

50.6 61.7

265

--- --- --- ---

7.2 --- --- --- --- --- --- --- ---

7.0 7.1

6.8

--- --- --- --- --- --- --- ---

--- --- --- ---

7.4

7.3

7.0 7.2

--- --- --- --- --- --- --- ---

--- --- --- ---

7.4

7.2 7.3

7.1

--- --- --- --- --- --- --- ---

--- --- --- ---

--- --- --- --- --- --- --- --- --- --- --- ---

7.3

7.4

7.2

7.2 7.3

6.8 7.0

7.0

--- --- --- --- --- --- --- ---

--- --- --- --- --- --- --- --- 7.1 7.2 7.3 7.4 --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- ---

--- --- --- --- --- --- --- ---

--- --- --- ---

--- --- --- --- --- --- --- ---

Sound Transmission Coefficient (STC) = 23

66.8

68.0

62.8 62.3

208

67.6

69.5

64.9 64.5

230

64.0

60.6 61.7 63.2

265

66.8

68.0

62.8 62.3

208

67.9

64.8 64.5 69.5

230

64.0

63.2

60.6 61.7

265

GA

Mode

Operating

Low Cool

Medium

OUTDOOR SOUND PRESSURE DATA

Cool

High Cool

Low Heat

Heat

Medium

36

High Heat

NOTES:

The tables above indicate the approximate indoor and outdoor sound levels of an ETAC unit.

1.

Tests were conducted in the Gree Sound Testing Laboratory according to AHRI (Air Conditioning, Heating and Refrigeration Institute) Noise Rating Standard 300 for non-ducted indoor air conditioning equipment.

FIELD--INSTALLED ACCESSORIES

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive compone

nt HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces do

wntime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Fr

iedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive compone

nt HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces do

wntime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Fr

iedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

OUTDOOR GRILLE SIZING

IMPORTANT: If you wish to use a grille not made for the Gree E-TAC contact Gree Application Engineering.

The following guidelines must be followed in the initial selection of any alternate exterior grille or louver:

The above criteria must be followed, since a louver that is restrictive or allows re--circulation will result in a reduction of the unit’s capacity and efficiency and will ultimately shor ten the compressor life.

OUTDOOR AIR VENTILATION

The ETAC will supply outdoor air through the ventilation opening in the partition wall into the room. The following ventitation airflow is based on the vent door fully open and the indoor fan operating at HIGH speed:

1. The louver must haveaminimum of 65% free area. Free area is the minimum area of the opening in an air inlet or outlet in which air can pass. Free Area (%) = X/Y.

2. The louver should be attached to the wall sleeve in a manner that will prevent recirculation of condenser discharge air into the inlet. In most applications, baffles, splitters, and/or gasket will be required between the chassis tube end sheets and the recirculation.

Cooling Capacity Size Max Vent Aiflow (CFM)

7,000 45

9,000 65 12,000 75 15,000 75

louver t o prevent air

Y

X

Lou ver Dimensional Reference

Y

Sample Calculations

Free Area (%) =

F.A. (%) =

X

Y

x y

x = 1 y = 1.5

1

x 100 = 66.7%

1.5

X

Y

x 100

X

E-TAC

37

WIRING SCHEMATIC

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree GA series PTAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wa

ll slee

ve

exte

nsion (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree GA Series will meet your needs.

The Gree GA series Packaged Terminal Air Conditioning (PTAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

GA

E-TAC

GA

E-TAC – Typical Wiring Schematic for Standard Units

(Except Models with 5KW Elec. Heaters)

38

WIRING SCHEMATIC

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

E-TAC

E-TAC – Typical Wiring Schematic for Models with 5KW Elec. Heaters

39

TYPICALWIRINGSCHEMAT IC FORENERGY

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

MANAGEMENT INTERFACE

GA

E-TAC

B

E-TAC #1

AW G--- American Wire Gage B--- Black PTAC --- Packaged Te rminal Air Conditioner W--- White

NOTES:

1. To size transformer, use the following equation:

Quantity of ETAC units x 0.1VA = transformer Size (VA) Example: 110 ETAC units x 0.1VA = 11 VA (24V) Transformer

2. Following are recommended wire sizes: Recommend 20 AWG wire (or larger) for wire runs up to 2,000 feet in length

W

LEGEND

FRONT DESK SWITCH PANEL

B

E-TAC #2

W

N MOOR101 MOOR001 MOOR

FIELD-SUPPLIED

24-V

TRANSFORMER

(SEE NOTE 1)

B

E-TAC #N

W

GA

40

TYPICAL WIRING SCHEMATIC FOR MULTIPLE E-TACS

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC

components

• Less sensitivity to building orientation (sun,

wind, shade)

• Optional architectural grille to permit custom

exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance

engineering staff

• Two--part delivery to minimize on--site

damage

• Weather--protected wall sleeve that goes in

place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling

or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No e

xpensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servi

cing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see access

ory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

CONNECTED TO A SINGLE WALL THERMOSTAT

MASTER

PTAC

UNIT 1

UNIT 2

UNIT 3

R

Y

W

G

O

C

R

Y

W

G

O

C

R

Y

W

G

O

C

R

Y

W

G

O

C

R

Y

W

G

O

C

Do not daisy chain R (24 VAC). Only a single "R" is needed.

1.

2. Maximum of 4 E-TAC units can be connected to one single wall thermostat.

3. Wall thermostat wire is field-supplied and should be 18 to

20 gauge solid thermostat wire.

T’STAT

GA

E-TAC

41

PACKAGED TERMINAL COOLING UNIT

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expe

nsive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servic

ing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessor

y Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

WITH HEAT PUMP OR ELECTRIC HEATING

HVAC Guide Specifications Size Range:

Cooling: 7,200 to 15,000 Btuh Electrical Heating: 5,600 to 17,100 Btuh

Heat Pump: 6,100 to 13,800 Btuh

Model Numbers:

Cooling with Electric Heat Heat Pump with Electric Heat

Part 1—System Description

Packaged Terminal Air Conditioners shall be of the sizes and capacities as shown on the contract drawing schedule and in the specifications.

System shall be tested to insure no water infiltration

E-TAC

into the room, when tested at eight inches of rain per hour with 40 mph (64.4 KPh) wind.

The complete system shall consist of the following:

A. Packaged Terminal Heat Pump or Heat/Cool

B. Power Cord or Hardwire Kit shall provide the

C. Insulated Polymer Wall Sleeve shall provide

D. Wall Sleeve Molding shall trim the wall sleeve to

E. Outdoor Polymer Louvered Grille shall resist

F. Subbase will support the wall sleeve when it

Chassis : See section 2 -- Chassis Description

power connection to the unit.

excellent thermal insulation, be textured to hide scratches and prevent shine, will have superior outdoor noise absorption and shall be corrosion free for the life of the product. The Wall Sleeve must have dimensions of 42” (1067 mm) width x 16“ (406 mm) height x 14--7/8” (377.8 mm) depth and be shipped with a rear weather barrier installed.

the existing wall to hide wall imperfections and irregularities due to the sleeve opening.

corrosion, breakage and match the color specified on drawing schedule and specifications.

extends into the room more than 4“ (101.6 mm). Subbase must come from the factory pre-assembled, (size as specified on drawing schedule and specifications).

Part 2—Chassis Description

2.1 General:

The chassis shall be a factory--assembled, single--piece heating and/or cooling unit, that is simple to install and operate. Just slide the chassis into a wall sleeve, plug it into an outlet, and operate after installation. The chassis dimensions sha exceed 42” (1067 mm) wide and 16“ (406 mm) high with room cabinet in place. The chassis shall consist of the following functional sections and components:

A. Certifications:

B. Operating Characteristics:

C. Electrical:

D. Safeties:

System shall be approved and certified by UL & UL, Canada. Chassis shall meet ASHRAE Standard

90.1 for minimum energy efficiency.

Chassis shall be capable of starting and running at 115˚ F (46.1˚ C) ambient outdoor temperature per maximum load criteria of ARI Standard 310/380.

The power cord will be 58” (1473 mm) for 208/230v models or 15“ (381 mm) for 265v models. The Hardwire kit accessory will provide 36” (914 mm) of flexible conduit. The chassis current draw shall be specified on the chassis nameplate and match electrical requirements specified on the Contract drawing schedule and specifications. The power cord plug configuration shall conform to NEMA standards and the rating shall support the current draw of the electric resistance heater. For 265v installations, UL codes require the use of an electrical equipped subbase for power cord usage or hardwire conduit for non--corded installations.

Compressor shall have automatic reset, over temperature and over current protection. The fan motors shall have an inherent, automatic reset over temperature protection. The electric heate shall have two over temperature protectors.

ll not

r

42

E. Air Flow System:

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive c

omponent HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduce

s downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory F

riedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive c

omponent HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduce

s downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory F

riedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive c

omponent HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduce

s downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory F

riedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

For superior sound and comfort, the airflow system shall consist of two, direct--drive permanently lubricated fan motors. The outdoor fan motor will be single speed, with a dynamically balanced, corrosion resistant, multi-blade axial flow design, with integrated slinger ring. The indoor fan motor will be three speeds, with a dynamically

balanced aluminum, tangential blower wheel, to assure uniform air distribution and optimal sound.

Both Fan Motors shall be of an enclosed design to reduce the effects of moisture and corrosion.

F. Compressor & Refrigerant:

The rotary--type Compressor shall be fully hermetic with internal and external vibration isolation. The refrigeration system will be sealed and contain a full refrigerant charge (R410A).

G. Coils:

E-TAC

Condenser and evaporator coils to be constructed of high-efficiency copper and aluminum, necessary to achieve EER and COP rating, as specified on the chassis name plate.

H. Factory--Installed Electr

The factory--installed, open coil type, electric heater is standard in heat/cool and heat pump chassis. The electric heater shall contain both an automatic reset and a one--shot over temperature protection device. The heating capacity of the electric heater shall be as identified on the Contract drawing schedule and in the specifications.

I. Controls:

All standard models shall be equipped with electronics, for added features and improved reliability of the unit.

The chassis shall have an easy to operate, user friendly, electronic display with simple to push, large digital buttons. All controls will be easily accessible and covered by a hinged door.

The mode selection control shall consist of OFF, FAN ONLY, HEAT, COOL and DRY operations. There will be 3 optional Fan Speed Options, LOW, MED or HIGH. The temperature selection will be controlled by color coded, simple to operate warmer and cooler buttons. The upper and lower setpoint temperature limits, can be easily configured.

All models shall have a configuration dipswitch, easily accessible for optimal comfort settings, CONTINUOUS or CYCLE fan mode in HEATING, CONTINUOUS or CYCLE fan mode in COOLING, FREEZE GUARD enabled or disabled, WALL

ic Heater:

THERMOSTAT enabled or disabled, EMERGENCY HEAT (for heatpumps), and 4 optional SETPOINT LIMIT selections.

Fan cycle configuration switches, will allow continuous fan operation for maximum comfort or cycle operation for maximum energy savings. Settings can be differe cooling operations, for maximum comfort and efficiency.

All standard models shall have Temperature Limiting control, with four easy to configure settings. Temperature limiting allows a room temperature range to be set to avoid extreme temperature settings and to maximize savings.

Emergency Heat Switch (Heat Pump Models Only) shall disable the compressor in heating mode and only allow the use of electric heat during heating cycles. The Emergency Heat switch is active at all outdoor ambient temperatures.

All units shall be capable of interfacing to a wall thermostat; haveablank control panel for wall thermostat applications; and have a removable wall thermostat terminal block, to simplify field wiring. No additional field--installed kits shall be required.

Wall thermostat interface shall provide two fan speed selections to maximize comfort.

Compatible with2wire central desk control systems.

Freeze Guard to automatically activate the electric heater and indoor fan to warm the room, to prevent damage from freezing temperatures. Freeze guard will be active as long as there is power supplied to the unit. Unit shall have the ability to disable Freeze guard, if needed.

Un in˚F or˚C.

Unit will have memory; in case power is lost, unit will return to all previous settings.

Unit will havearandom compressor restart after a power outage, to prevent power surges due to many units turning on at the same time.

Room temperature sensing shall useaSolid state thermostat control.

it shall have the option to display temperature

nt for both heating and

out label to cover the

GA

E-TAC

43

J. Front Panel (supplied with chassis): Front

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No

equipment room or maintenance

engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime: complete chassi

s can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retr

ofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive component HVAC system purchase

• No

equipment room or maintenance

engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduces downtime: complete chassi

s can be replaced in minutes without

disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory Friedrich Retr

ofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

panel shall be constructed of a polymer material to resist breakage and corrosion. It shall have a front louvered surface with integrated control door and air filters. The air filters shall be easily accessible without removing the front panel from the chassis.

K. Air Filters: The chassis shall contain air filters,

with a minimum of 40% arrestance per ASHRAE Standard 52.1. Two easily accessible front access supply air filters, shall be interchangeable, washable and permanent type. The vent filter shall beaone--piece, removable a filter.

L. Bi--Directional Discharge Grille: Bi--directional

polymer discharge grille shall resist corrosion and breakage. It shall be easily set to direct air at 40 degrees from horizontal or 80 degrees from

GA

E-TAC

horizontal. This non--metallic discharge grille shall be cool to the touch during the heating cycle.

M.Ventilation: The chassis shall have a manual

adjustable fresh air vent with a concealed manual control. The vent control shall allow a maximum of up to 65 CFM of fresh air to be drawn into the room when the indoor fan is operating and the door is open.

N. High Efficiency Condensate Removal System:

The chassis shall haveacondensate removal system consisting of a slinger ring integrated in the outdoor fan, to disperse condensate onto the condenser coil to be evaporated.

O. Accessories:

1.

Hardwire kit (PN: HARDWIRE-KIT-xxxV) shall be required if an accessory power cord is not used. The hardwire kit provides a permanent connection to the unit and shall have 36” (914 mm) of flexible steel conduit and a plug-in connector for easy connect/disconnect.

2.

Insulated Polymer Wall Sleeve (PN: SLEEVE-INSUL-1PK) shall be made from a molded polymer, with factory installed insulation and a minimum flammability rating of UL94-5V. The sleeve surface shall be textured to prevent shine and hide scratches.

3. Deep Wall Metal Wall Sleeve (up to 28” /

711.2 mm.) (PN: SLEEVE--EXTxx--1PK) shall beaone-- piece, extended wall sleeve, with factory installed insulation and deep wall baffles integrated.

nd washable type

4. Sleeve Molding (PN: SLEEVE--MOLDING) shall trim the wall sleeve to the existing wall to hide wall joints and irregularities due to the sleeve opening.

5. Architectural Grille

GRILLE--ALU--xxxxx)

durable life or painted aluminum for a superior color match to the building.

6.

Subbase (PN: PTAC-SUBBASE-A): Non- electrical subbase shall provide mechanical support and adjustable legs for leveling. the subbase. Access electrical modules below:

230V Receptacle Module (PN: PTACREC-230Vxx-A): 208/230V outlet receptacle module (available in 15, 20, or 30amp configurations) that mounts in the subbase.

265V Receptacle Module (PN: PTACREC-265Vxx-A): 265V outlet receptacle module (available in 15, 20, or 30amp configurations) that mounts in the subbase.

Disconnect Switch (PN: PTAC-SWITCH-A): Two (2) pole power disconnect switch (DPST) module that mount in the subbase.

Fuse Protection (PN: PTAC-FUSE-xxA): Fuse module (available in 15, 20, or 30amp) provides in-line over-current protection. The module mounts in the subbase and contains a cartridge-style fuse.

Drain Kit (PN: DRAIN-KIT-1PK): This

7.

universal drain kit shall be used internally or externally to route excess condensate to a central drainage system. The drain kit include both a straight tube and a 90˚bend tube.

Wall Thermostats

8.

A. Wireless Wall Thermostat (PN: TT-N631W)

The wireless digial wall thermostat and receiver

module provide maximum temperature control without pulling wires. The non-programmable wall thermostat comes complete with LCD

display, backlighting and two speed fan control.

B. Wired Wall Thermostats (PN: TT-N-411 & PN: TT-N-421) The digital wall thermostat shall have a large LCD display with backlighting, operate with 24VAC, be non-programmable, easy to use and provide maximum guest comfort.

(PN:GRILLE--PLA--xxxxx or

shall be polymeric for long

44

3.0 DELIVERY, STORAGE, AND

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive c

omponent HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduce

s downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory F

riedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• No expensive c

omponent HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapid servicing reduce

s downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve extension (see accessory F

riedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

HANDLING

The packaging of the chassis shall be sufficient to protect the chassis from damage during shipment via an enclosed truck. Chassis must also be able to withstand an impact force of 8 g’s and a random continuous force o f 1g, during shipping.

Chassis, wall sleeves, and grilles shall be shipped in separate cartons. Universal handling instructions shall be defined and visible on the carton, from front, back and sides.

Cha ssis shall be capable of withstanding temperatures from --40˚F to 155˚F (--40˚C to

68.3˚C), at 5 to 95 percent RH, non--condensing, during shipment an failure.

Chassis must be stored and left in a horizontal

position for serveral hours before attempting to engage or start unit.

d storage, without componen

t

E-TAC

45

3.0 DELIVERY, STORAGE, AND HANDLING

The packaging of the chassis shall be sufficient to protect the chassis from damage during shipment via an enclosed truck. Chassis must also be able to withstand an impact force of 8 g’s and a random continuous force o f 1g, during shipping.

Chassis, wall sleeves, and grilles shall be shipped in separate cartons. Universal handling instructions shall be defined and visible on the carton, from front, back and sides.

Cha ssis shall be capable of withstanding temperatures from --40˚F to 155˚F (--40˚C to

68.3˚C), at 5 to 95 percent RH, non--condensing, during shipment an

d sto

rage, without component

failure.

3.0 DELIVERY, STORAGE, AND HANDLING

The packaging of the chassis shall be sufficient to protect the chassis from damage during shipment via an enclosed truck. Chassis must also be able to withstand an impact force of 8 g’s and a random continuous force o f 1g, during shipping.

Chassis, wall sleeves, and grilles shall be shipped in separate cartons. Universal handling instructions shall be defined and visible on the carton, from front, back and sides.

Cha ssis shall be capable of withstanding temperatures from --40˚F to 155˚F (--40˚C to

68.3˚C), at 5 to 95 percent RH, non--condensing, during shipment an

d sto

rage, without component

failure.

GA

NOTES:

________________________________________________________________________________________

APPLICATIONS

• Hotels and motels

• Nursing homes and assisted living care

centers

• Offices

• Apartments

• Single--family dwellings

• Home conversions and residential add--ons

NEW CONSTRUCTION

ADVANTAGES FOR NEW CONSTRUCTION

Design Flexibility for the Architect/Engineer

• Whisper--quiet performance, indoors and out

• No bulky duct system

• No separate equipment room

• No water towers or additional cooling

equipment

• No complex match--up of different HVAC components

• Less sensitivity to building orientation (sun, wind, shade)

• Optional architectural grille to permit custom exterior appearance

Initial Cost Savings for the Buildin

g Owner

• N

o expensive component HVAC system

purchase

• No equipment room or maintenance engineering staff

• Two--part delivery to minimize on--site damage

• Weather--protected wall sleeve that goes in place during construction; chassis that slides in place after construction

• No seasonal changeover required for cooling or heating -- units are self--contained comfort systems

Lower Operating Costs and Reliable Comfort for The Occupant

• Heat pump models offer substantial savings over models with conventional electric resistance heaters

• Individual units allow tenants to choose the degree of comfort and operating economy.

• Rapi

d servicing reduces downtime: complete chassis can be replaced in minutes without disrupting other occupants.

• Each unit operates independently of other units in the building. No dependency by building on central HVAC system.

RETROFIT/REPLACEMENT

If you are replacing a unit in an existing wall sleeve, your options include:

• Replace the existing wall sleeve with the the polymer wall sleeve. See accessory sleeve section for selecting the correct sleeve for your application. NOTE: in most cases, when replacing the wall sleeve, the exterior grille must also be replaced.

• Use an existing sleeve and exterior grille. The Gree E-TAC will fit into:

—

— Friedrich T series and ZoneAire wall

sleeves, with a required wall sleeve ex

tension (see accessory Friedrich

Retrofit Wall Sleeve Adapter).

Whether you are designing a new structure or replacing packaged terminal air conditioning units in an existing building, Gree E-TAC will meet your needs.

The Gree E-TAC Packaged Terminal Air Conditioning (E-TAC) unit is designed to meet the needs of the architect, engineer, and contractor. For unit installation, Gree’s expert support network will assist in all applicable aspects of the construction project, from preparing a budget to start-up.

4

The following major competitors’ wall sleeves/grilles: Carrier, GE, Amana, Trane, Friedrich and Bryant, and NO accessory retrofit kit is required.

NOTES:

________________________________________________________________________________________

E-TAC

________________________________________________________________________________________

_______________

________________________________________________________________________________________

_________________________________________________________________________

GA

________________________________________________________________________________________

46

3.0 DELIVERY, STORAGE, AND HANDLING

The packaging of the chassis shall be sufficient to protect the chassis from damage during shipment via an enclosed truck. Chassis must also be able to withstand an impact force of 8 g’s and a random continuous force o f 1g, during shipping.

Chassis, wall sleeves, and grilles shall be shipped in separate cartons. Universal handling instructions shall be defined and visible on the carton, from front, back and sides.

Cha ssis shall be capable of withstanding temperatures from --40˚F to 155˚F (--40˚C to

68.3˚C), at 5 to 95 percent RH, non--condensing, during shipment an

d storage, without compone

nt

failure.

GA

NOTES:

________________________________________________________________________________________

_______________

_________________________________________________________________________

________________________________________________________________________________________

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Printed in U.S.A.

Edition Date:9/15

&DWDORJ1R37$&*%3'

Gree ETAC12HP230V30AA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual