Gree 13-04582 user guide manual

Page 1

OWNER’S MANUAL

CANADIAN STANDARDS

3-IN-1 MOBILE

AIR CONDITIONER

Please read the following owner’s manual before using this air conditioner. Keep this manual along with your proof of purchase in a safe place for future reference.

MODEL : 13-04582

00223-27/12/06

Page 2

TABLE OF CONTENTS

USE ........................................................................3

SAFETY NOTES ........................................................3

UNIT DIAGRAM

Front........................................................................4

Back ........................................................................4

Installation Kit ..........................................................4

INSTALLATION

Electrical requirements ............................................ 5

Preparing the air conditioner.................................... 5

Choosing the location .............................................. 6

Fixing the exhaust hose ............................................ 6

Wall installation ...................................................... 6

Installation by window type .................................... 7

CONTROL PANEL AND LCD DISPLAY

Control panel .......................................................... 8

LCD display ............................................................ 8

UNIT OPERATION

Cooling .................................................................. 9

Dehumidifying ........................................................ 9

Fan ........................................................................ 9

Auto Mode .......................................................... 10

Sleep Mode .......................................................... 10

Setting the timer .................................................... 10

REMOTE CONTROL ....................................11-12-13

WATER DRAINAGE ................................................14

MAINTENANCE

Cleaning the housing ............................................15

Cleaning the filter ..................................................15

Storage........................................................... ......15

TROUBLESHOOTING CHART ........................... ......16

TECHNICAL SPECIFICATIONS ................................17

CUSTOMER SERVICE ............................................17

WARRANTY............................................................18

Page 3

WARNING

Before using this air conditioner, please read this owner’s manual carefully. This manual is not a contract and should be used as a reference guide only. We reserve the right to make technical changes at all times without prior notice.

USE

Thank you for purchasing this 3-in-1 mobile air conditioner. This unit is designed to improve indoor living and working comfort by providing cooling, dehumidifying and ventilation with minimal installation. Unlike traditional portable units, there is almost no tank to empty as the unit evaporates 80% of the condensate water which is drained through the hot air exhaust hose. When using this appliance, always take basic safety precautions.

SAFETY NOTES

1. Always place the unit on a flat surface in a cleared out area.

2. The unit must be connected to a grounded power supply properly rated. For your safety, this unit is

grounded through the power cord plug when connected to a grounded wall outlet. Never use an adapter plug or extension cord, nor plug the unit in a damaged receptacle.

3. Before unplugging the unit, always turn it off. Always unplug the unit before cleaning or servicing it.. When unplugging the unit, never pull on the power cord - always grip the plug.

4. Ensure that removable covers, hoses and other accessories are correctly fitted before running the unit.

5. Do not install or use the unit in the following places :

• near a heat source ;

• an area with possible gas leakage or in an explosive atmosphere ;

• near a bath, shower enclosure, swimming pool, or any other steamy and wet areas ;

• in a greenhouse.

6. Do not apply insecticides or any other flammable products on the unit.

7. Do not start or stop the unit by plugging in or pulling out the power cord.

8. Do not operate with wet hands or spray water or other liquid on the unit, nor immerse

the appliance.

9. This unit is not intended for the use of children and close supervision is necessary when it is operating near children.

10. Never insert fingers, foreign objects, or anything to obstruct the air inlet and outlet grills. Always warn children.

11. Do not cover the appliance.

12. Do not expose skin or eyes directly to cool air over a long period of time.

13. If an abnormal odour or smoke comes out of the unit, immediately unplug the unit and contact

SUNRISE TRADEX Customer Service.

14. When opening the filter cover, do not touch the internal metal parts of the unit.

15. Always check the power cord for signs of damage before use. If the power cord is damaged, contact

SUNRISE TRADEX Customer Service.

16. Do not place a plant or allow a pet to be exposed directly to the unit cool air flow.

17. Do not put any combustion appliance in the direct path of the unit airflow ; it could affect the

combustion efficiency.

18. Do not sit on the unit or place anything on the unit.

19. Always store the unit standing up. If the unit is to be moved or carried horizontally, wait 24 hours

before plugging the air conditioner.

20. Before storing the unit in a clean and dry area, drain the water and clean the filter.

Page 4

UNIT DIAGRAM

Front

Back

upper air inlet grille

electric cord

hot air outlet

upper air outlet

handle

lower air inlet grille

control panel

lower air inlet grille

water drain hole

INSTALLATION KIT

square hose adaptor to unit

air exhaust hose

window adjustable slider kit

oval hose adaptor to window

Page 5

ELECTRICAL REQUIREMENTS

1. The air conditioner must be grounded ; it is equipped with a LCDI

(Leakage Current Detection and Interruption) power cord and plug This feature will circuit trip the electrical power source if the nominal current leakage between the cord shield and either load conductor exceeds a predetermined value. The cord will remain out of power until the device is manually reset. This is intended to protect against electric shock and to reduce the risk of a fire in the power cord or combustible materials nearby. The cord shield is not grounded and must be considered a shock hazard if exposed. The cord shield must not be connected to ground or to any exposed metal.

2. Do not cut or bypass the plug ground prong. If you do not have a grounded outlet available near the air conditioner, have one installed by a qualified electrician.

3. The power supply rated voltage is ± 6%.

4. Do not connect the unit to an outlet being used by other appliances; ideally, connect to a single

grounded 15A circuit (time-delay fuse or circuit breaker).

5. If the power cord or plug is damaged, call SUNRISE TRADEX Customer Service.

• Electrical ratings of the air conditioner are detailed on the rating plate on the back of the unit.

• Basic electrical requirements are listed hereafter. Please make sure to check the following before installing and connecting your unit.

INSTALLATION

Casters

Drain hose

Cap Clamp

Rear grille

PREPARING THE AIR CONDITIONER F

IXING THE CASTERS (Some models only)

To avoid the risk of causing damages to the air conditioner, you must install the casters before using the appliance.

1. Open the accessory bag and take the 4 casters out.

2. Recline the unit, one side at a time, to insert the unit into

the base holes. Do not recline the unit more than 45° from the ground.

3. Screw the casters into the base threaded holes.

INSTALLATION OF THE DRAIN HOSE (Some models only)

You must fix the drain hose before operating the unit.

1. Take out the drain hose, the hose cap and the clamp from the accessory bag.

2. Insert the drain hose into the drain hole on the lower back of the unit. Make sure that the drain hose is correctly inserted into the drain hole.

3. Put the hose cap on the free end of the drain hose.

4. Fix the drain hose on the rear grille with the clamp.

Page 6

INSTALLATION

CHOOSING THE LOCATION

Place the unit on a level surface in a cleared out area where the air outlets cannot be obstructed. For a maximum efficiency, keep a clearance of at least 50 cm

(20”) front

and rear of the unit (Figure A).

FIXING THE EXHAUST HOSE

• During the operation of an air conditioner, a large flow of hot air must be exhausted out of the room. The exhaust hose supplied with this air conditioner must be connected at all times (when running in air conditioning mode) to exhaust the hot air out.

LIDE THE HOSE SQUARE ADAPTOR ALL THE WAY

DOWN OVER THE HOT AIR OUTLET ON BACK OF

THE UNIT

(Figure B).

WALL INSTALLATION

• The hot air must be exhausted outdoor through a window, a patio door or directly through the wall.

1. Pick an exterior wall where you will be able

to correctly install the air conditioner and the hot air outlet.

2. Drill a hole of 13,3 cm (5-1/4”) on the

exterior wall. The hole must be 40 to 130 cm (16” to 50”) above the floor (Figure C).

3. Fix the external end of the exhaust hose onto

the wall pre-drilled hole.

NOTE :

The hot air exhaust hose must be as short as possible. To avoid hot air backdraft and guarantee an efficient exhausting of the hot air, make sure the hose is not bent, kinked or twisted (Figure D). In order to do so, please check upon the following :

• Position the air conditioner as close as possible to the outside air outlet.

• Unscrew the hose connector, cut the excess hose and screw the connector back on the hose.

• Do not forget to leave a 50 cm (20”) clearance all around the air conditioner.

• To maximize the efficiency of the air conditioner, you may insulate the exhaust hose with a 6” insulating flexible tube (not included).

840 mm

50 cm50 cm50 cm

450 mm

370 mm

Figure A

Figure B

130 cm (50”)

40 cm (16”)

MUR

Figure C

Figure D

Note : model may differ from illustration.

Page 7

Casement window

1. It is recommended to replace the screen with a clear plexiglass panel (1/4'') fitted to the size of your window screen.

2. Cut a hole to the same size as the window oval adaptor of the exhaust hose - approximately 13,3 cm (5-1/4”).

3. Correctly fit on the adaptor.

4. Fix it on the plexiglass using

4 screws (not included).

Sliding windows or patio door

1. Install the window slider kit

vertically or horizontally within the inside frame (vertically for a patio door). If necessary, screw the slider kit on the frame.

2. Close the window onto the window kit to form a tight seal.

3. Attach the exhaust hose adaptor to the window slider kit; the adaptor tabs will lock into place the adaptor to the window kit.

INSTALLATION

NOTE :

Using the window slider kit may make it difficult to correctly close and/or lock the window. Additional safety precautions should be considered.

• Make sure to correctly install and insulate the window slider kit. It must perfectly fit into the window. The length can be adjusted. The three pieces are easy to cut and slide well into each other.

• Tape the edge around the slider kit to stop insect or bug intrusion (tape not included).

HUNG

WINDOW

CASEMENT

WINDOW

INSTALLATION BY WINDOW TYPE

SLIDING

WINDOW or PATIO DOOR

Note : model may differ from illustration

Page 8

OFF

LOW MD HIGH

SLEEP

COOL

DRY

SET TEMP

AUTO

SET TIME

CONTROL PANEL AND LCD DISPLAY

Press this button to turn the unit on or off.

Press this button to select one of the following modes : COOL, FAN, DRY or AUTO.

In COOL, FAN or AUTO mode, press this button to select the fan speeds (LOW

- MEDIUM - HIGH). In DRY mode, the fan speed cannot be adjusted.

To set temperature in cooling or auto mode.

To set the time (# of hours) when the timer is on.

Sets the air conditioner in SLEEP mode (automatic shut off).

SLEEP : In sleep mode (automatic shut off) COOL : In cooling mode FAN : In fan only mode DRY : In dehumidifying mode

SET TEMP : Displays the set temperature

AUTO : Auto mode

: Fan speeds -

LOW/MEDIUM/HIGH

SET TIME : Displays the hours set when

timer is on

ON : Timer is on OFF : Timer is off

LCD DISPLAY

CONTROL PANEL

*HEATING mode is optional on some models.

FAN

Page 9

UNIT OPERATION

• Plug the power cord into a properly rated grounded outlet. Do not connect the unit to an outlet that is being used by other electrical appliances.

• Then press the ON/OFF button to begin operation.

• When starting the air conditioner, always set the unit to COOL and the temperature to the coolest degree - 16

C (61oF). Let it run with for 2 hours.

• When the desired room comfort level is reached, adjust the fan speed to maintain this temperature and adjust temperature accordingly if necessary.

• Since the air conditioner takes few hours to cool off the room, it is recommended to let the air conditioner work 24/24 h. and adjust the temperature instead of stopping and starting the air conditioner on a daily basis.

• If the unit is turned off while running in COOL, DRY or AUTO mode, when turning the unit back on, allow 3 minutes before the compressor resumes.

COOLING

1. Press the MODE button and set until the COOLING icon lights up.

2. The display will show the set temperature. Press on the temperature button to set the

temperature - 16

C to 31oC (61oF to 88oF).

3. Press FAN SPEED to set fan speed at LOW, MEDIUM or HIGH ; each speed level is

identified by an icon lighting up when selected .

• When the room temperature is slightly warmer than the set temperature, the compressor starts running and the air conditioner cools the room off. When the room temperature is slightly colder, the compressor stops, but the fan keeps on running.

• The exhaust hose must be correctly installed and that the air inlet and outlet grilles must be cleared out.

• Make sure that the drain hose and cap are correctly installed.

• For maximum efficiency, draw the curtains or blinds if the room is exposed to direct sunlight.

• Do not place near a heat source.

DEHUMIDIFYING

RESS THE MODE BUTTON UNTIL THE DEHUMIDIFYING ICON LIGHTS UP.

• The exhaust hose must be correctly installed.

• In dehumidifying mode, the fan runs at low speed and speed cannot be changed.

• Make sure that the drain hose and cap are correctly installed.

• The unit will not operate if the room temperature is lower than 16

C (61oF).

• For maximum dehumidifying efficiency, keep windows and doors closed.

FAN

1. Press the MODE button and set until the FAN icon lights up.

2. Press FAN SPEED to set fan speed at LOW, MEDIUM or HIGH ; each speed level is

identified by an icon lighting up when selected .

• In FAN mode, the exhaust hose is inoperative.

Page 10

UNIT OPERATION

AUTO MODE

The unit built-in microcomputer analyses the temperature and humidity level in the room ; the air conditioner controls and automatically adjusts the cooling system (compressor on or off) and the fan speed. This self-adjustment feature allows you to maintain room comfort by controlling the temperature and air dehumidification in the room.

To set in AUTO mode, press the MODE button until AUTO lights up on the control panel.

• Exhaust hose, drain hose and cap hose must be correctly installed in AUTO mode.

• The TIMER may be used in AUTO mode.

SLEEP MODE

When setting this mode, the air conditioner will automatically shut off in 7 hours. This is a fast way to program an automatic shut off of the unit for the night for an optimal room comfort ; it is also energy saving.

1. Unit must be running when using this mode.

2. Press on the SLEEP button until the SLEEP icon lights up on the panel.

3. The air conditioner will automatically shut off after 7 hours.

4. For programming a shut off in less than 7 hours, use the TIMER button to adjust the

delay by 1/2 hour slot up to 7 hours maximum. The LCD display will show the set time.

5. To cancel, press again the SLEEP button until the SLEEP icon goes off.

• When the SLEEP mode is on, you can still modify/program any other function on the unit.

• You cannot set the TIMER ON for an automatic shut off if the unit is in SLEEP mode.

• The SLEEP mode cannot be used if the air conditioiner is in AUTO mode.

SETTING THE TIMER

When the unit is operating, the timer can be used to set an automatic shut off time. If the unit is off but still plugged, the timer can be used to set an automatic start time.

UTOMATIC STARTING :

1. While the unit is off, press the TIMER button until the TIMER ON icon lights on.

2. Press the up/down arrows on the TIMER button to set the time (number of hours)

before the air conditioner turns on (1-24 hours) ; LCD display will show the set time

UTOMATIC SHUT OFF :

While the unit is running, repeat steps 1 and 2, as detailed previously for an automatic shut off.

• To cancel the timer, whether you are programming an automatic start or shut off of the air conditioner, simply press on the TIMER button until the OFF icon lights on.

Page 11

REMOTE CONTROL

How to insert the batteries

• Following the arrows shown in the figure, remove the battery cover.

• Insert the 2 batteries, making sure that the terminals (+ /-) are correctly fitted.

• Put the cover back into position.

Note :

Always use 2 AAA 1.5V battaries. Replace batteries with new ones when the LCD display of your remote is fading out.

You can control your air conditioner from a distance with the remote control provided with your unit. The remote can control the same functions than those operated directly from the unit on the control panel. Before using the remote, do not forget to insert 2 AAA 1.5V batteries (included).

USING THE REMOTE :

• Always line up the remote signal transmitter with the unit signal receiver on the front panel.

• The LCD display of the remote will show all the messages and icons you may need to control your air conditioner from a distance.

• All operational functions of your remote, as well as message and icon identification are described in the next 2 pages.

• After entering a mode or function on your remote, always press on SEND to initiate the command on the unit. You will hear a “beep” from the unit, meaning that the function has been received and initiated.

• When keying a function or mode on the remote, the identification icon or message flashes on the remote LCD display and stops flashing when the SEND button is pressed.

POWER FAILURE

• In case of a power failure during operation, all settings programmed directly from the unit will be cancelled.

• However, the remote control will keep in memory the last settings programmed on the remote control. To resume operations, simply press on SEND.

• If the air conditioner does not work properly, unplug the unit and plug it back.

• Wait 3 minutes and then turn the unit on.

• Press SEND on the remote control to resume last operations set from the remote.

Page 12

REMOTE CONTROL

MODE : to set the air conditioner in AUTO, COOL or FAN mode

SLEEP : to set the air conditioner in SLEEP mode

I/O (ON/OFF) : to start or close the air conditioner

TIMER : to set the timer or the clock (time)

DRY : to set in DEHUMIDIFYING mode

SEND : initiate all operations of the air conditioner

+oC / -oC :

to set temperature

To set the number of hours when the timer is on or the time (clock)

LCD DISPLAY

FAN : to set fan speeds

*Product may differ from illustratiion

TO START OR STOP THE AIR CONDITIONER :

Press on the I/O (ON/OFF) button.

TO SET THE MODE :

• Press on MODE until the matching icon flashes on the remote LCD display : for COOLING mode, for FAN ONLY mode ou for the AUTO mode.

• Press on SEND to initiate the operation on the air conditioner ; a “beep” will confirm transmission and the icon will stop flashing.

IMPORTANT: some screen may display a “sun” icon for HEATING mode; this mode is available only

on some models.

TO SET FAN SPEED :

• Press on FAN and choose the speed : HIGH, M (Medium) or LOW - each speed icon will flash.

• Press on SEND ; a “beep” will confirm transmission and the speed icon will stop flashing.

TO SET TEMPERATURE :

• Press on +°C or -°C to set the desired température - the temperature icon will flash. The temperature is increased or decreased by 1°each time you press on these buttons. The temperature settings range from 16°C to 30°C (61°F to 86°F).

• Press on SEND ; a “beep” will confirm transmission and the temperature icon will stop flashing.

NOTE : all the above operations can be keyed in on the remote control before pressing on SEND

to initiate the operations on the air conditioner.

EX. : to set your air conditioner in COOLING mode, at HIGH fan speed and at

22°C :

• press on MODE until the COOLING flashing icon shows on the LCD display ;

• then, press on FAN until the HIGH flashing icon shows on the display - when pressing on FAN,

the cooling icon will stop flashing;

• then, press on +

or -

until you reach 22

C - the temperature icon will flash and the FAN

icon will stop flashing ;

• to complete, press on SEND - a “beep” will confirm transmission and the temperature icon will

stop flashing.

Page 13

DEHUMIDIFYING MODE :

• Press on DRY to set the air conditioner in dehymidifying mode - will show on the remote control LCD display ; press on SEND.

• To cancel this mode, simply press on DRY again.

• In DRY (dehumidifying) mode, the compressor is running but the fan speed cannot be changed.

TIMER AND TIME (CLOCK) :

When pressing on TIMER , you may select TIMER to put the timer on and set the number of hours, or you may select TIME (CLOCK) to set the current time.

TO SET THE TIMER : For an automatic start of the air conditioner :

1. Press on TIMER - the TIMER icon will flash and the LCD display will show 0.5 if there have been

no previous setting - otherewise, the display will show the time set previously (number of hours).

2. Press on Hr - the number of hours icon will flash and the TIMER icon will stop flashing ; keep on

pressing Hr to set the number of hours (1-24) before the air conditioner starts. From 0 to 8, time will increase by 1/2 hour ; from 8 to 24, it will increase by 1 hour.

3. Press on SEND ; a “beep” will confirm transmission and the time (hours) icon will stop flashing.

TO SET THE TIME (CLOCK) :

• Press on TIMER until the TIME icon flashes - the LCD screen will display the current time.

• To change the time, press on Hr - the hour icon will flash ; set the hour, then press on Min to set the minutes - the minute icon starts flashing and the hour icon stops flashing ; set the minutes, then press on SEND - the minute icon will stop flashing.

MPORTANT : always check and set the clock at the right time before initiating the timer or the sleep

mode ; do nof forget to press on SEND.

SLEEP MODE

This mode is a fast way to set a 7-hour time delay automatic shut off of your air conditioner.

1. Set this mode when the air conditioner is running.

2. Press on SLEEP ; the SLEEP icon will appear on your remote display ; your air conditioner will

automatically stop running in 7 hours.

4. If you want an earlier shut off, press on Hr - the hour icon will flash ; you may increase the time

(1 hour at a time) up to 7 hours.

5. Press on SEND ; a “beep” will confirm transmission and the hour icon will stop flashing and the

remote LCD screen will display the time left before the shuf off of the air conditioner.

6. To cancel the SLEEP mode, simply press on SLEEP again - the SLEEP icon will go off, then press

on SEND.

• For other operational settings, proceed as detailed previously.

REMOTE CONTROL

Page 14

WATER DRAINAGE

When the unit is in cooling mode, the air humidity is converted in water used to cool down the unit. 80% of the water is condensated and evaporated outdoor through the exhaust hose. When the unit is used in extremely humid environment, exceeding water will be drained into a pan located at the bottom of the unit. When the water pan is full, the compressor stops but the fan keeps on running.

When the water pan is full, an overflow alarm will “beep” and the LCD display will show an H8 message, meaning that the tank is full, and the unit will stop running. To resume operation, empty the water tank as per the following:

1. Turn the unit off. Do not move the unit when the water pan is full.

2. Unclamp the drain hose from the rear grille.

3. Place a 2 L container under the drain hose.

4. Remove the cap from the drain hose. The condensate water will drain out

automatically. When the 2 L container is full, put the cap back into the drain hose to stop the water from draining out. Empty the 2 L container. Repeat until all the water is completely drained out.

5. Once the water container is empty, put the cap back into the drain hose and clamp the hose back on the grille.

Drainage port

CONTINUOUS DRAINAGE (NOT SHOWN)

- For a continuous drainage, take a hose of the appropriate length (not ncluded) and connect to the drainage port (located at the bottom).

- Place the other end into a drain such as a floor drain or else.

IMPORTANT :

Make sure that the drainage hose (not included) is always lower than the drainage port of the unit.

Fig 1

Page 15

MAINTENANCE

CLEANING THE HOUSING

• Wipe the surface of the unit with a soft damp cloth. Cleaning the unit with gasoline, paint thinner, chemical products or abrasive detergent could damage it. Use mild soap.

• Do not clean the air conditioner directly under a faucet or with a garden hose - its electrical components could be damaged and cause electric shocks.

• Avoid direct exposure to sunlight as this may affect the finish colour.

CLEANING THE FILTER

• Open the rear grille of the air conditioner and take the filter out.

• Immerse the filter gently in lukewarm water and a mild detergent. Rinse thoroughly, let it dry completely and put the filter back.

• For maximum efficiency of the air conditioner, clean the air filters every two weeks, or more frequently if there are animals around.

• If the filter is damaged or used, contact SUNRISE TRADEX Customer Service.

STORAGE

• Turn the unit off and unplug.

• Drain all condensate water from the unit.

• Turn the unit to fan mode for a couple of hours to completely dry out the inside.

• Clean the filter.

• Wind the power cord to the hangers.

• Always store the unit upright in a clean and dry aera. It is recommended to store the unit in its original packing carton.

Always turn off and unplug the unit before cleaning to avoid electrical shock.

Notes :

• If the unit is not used on a regular basis, it is recommended to turn it on once in a while

to keep the compressor in good working condition.

• After running for several seasons, the air conditioner internal components may get dirty

and/or obstructed - the unit may become less efficient. Regular maintenance is recommended. Contact SUNRISE TRADEX Customer Service for maintenance or repair.

Filter cover hooks

BACK OF THE UNIT

Filter cover

Page 16

TROUBLE-SHOOTING

Before asking for service, please check the following troubleshooting chart.

PROBLEM

The air conditioner does not work.

The indicator shows the air conditioner is running, but it does not work.

Air cooling is not efficient.

LCD window shows an E1 error message.

LCD window shows an H8 error message.

The unit is smelly

The air conditioner is noisy and/or vibrates.

There is water dripping on the inside floor ?

CAUSE

Power supply :

1. Unit is not plugged in.

2. The plug or receptacle is

damaged.

The timer is on.

1. The humidity of the room is under 30%.

There is frost on the evaporator.

The air filter is dirty.

4. The temperature is inadequate.

5. Is there any heat source in the room ?

6. Is the hot air exhaust hose correctly installed ?

Power supply is unstable and the unit is not working properly.

The water tank is full.

Is the air filter dirty ?

Is the air conditioner leveled ?

Is the drain hose and the hose cap correctly installed ?

SOLUTION

1. Plug in correctly

2. Change the plug or

receptacle.

Cancel the timer or wait for the unit to start.

1. Increase the humidity level.

2. The unit is defrosting ; it will

resume after the defrosting

cycle is completed.

3. Clean or change the filter.

4. Increase the temperature and the fan speed.

5. Close or move the heat

source.

6. Check the installation of the

hot air exhaust hose and insulate it.

Stop the air conditioner (switch off the power supply). Wait 10 minutes and turnit back on ; if E1is still on , call SUNRISE TRADEX Service.

Drain out and empty the water tank.

Clean the air filter, as well as the front and back grills.

Make sure the air conditioner is on a level and flat surface.

Secure the installation of the drain hose and the hose cap and make sure the unit is on a level surface.

***NEVER OPEN THE AIR CONDITIONER.

Page 17

TECHNICAL SPECIFICATIONS

Specifications listed hereafter are for references only. Please see technical data on your air conditioner unit rating plate.

CUSTOMER SERVICE

Contact SUNRISE TRADEX CORP. Customer Service for:

• Replacement parts

• Technical support

• Warranty claims

• Customer service.

Page 18

LIMITED WARRANTY

This air conditioner is covered by a warranty against defects in materials and workmanship, if used for the applications specified in this owner’s manual, for a period of TWO (2) years from the date of original purchase in Canada.

Note : The internal compressor is covered by a 5-year limited warranty.

During the warranty period, if the air conditioner fails under normal use, SUNRISE TRADEX CORP. will, at its option, either repair the unit or replace it, free of charge, within a reasonable period of time after the air conditioner is returned.

As a condition to any warranty service obligation, the customer must present this warranty certificate along with the proof of purchase.

THIS WARRANTY DOES NOT COVER :

1. Damage, accidental or otherwise, to the air conditioner that are not caused by material or

workmanship defect.

2. Damage caused by misuse, tampering or failure to follow the operating and maintenance instructions provided in this owner’s manual.

3. Damage to the finish of the unit enclosure or to other outer features caused by wear.

4. The filter.

5. Damage caused by repairs or modifications to the air conditioner made by any person not

duly authorized by SUNRISE TRADEX CORP.

6. Insurance and freight costs for the warranty service.

ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, ARE LIMITED TO A TWO YEAR (2) PERIOD COVERED BY THIS EXPRESS LIMITED WARRANTY. SUNRISE TRADEX CORP. DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND, IN NO EVENT, SHALL SUNRISE TRADEX CORP. LIABILITY EXCEEED THE RETAIL VALUE OF THE AIR CONDITIONER FOR BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS PORTABLE AIR CONDITIONER.

Keep this owner’s manual along with your proof of purchase in a safe place for future reference. You must provide proof of purchase for warranty service.

Enter the following information on your air conditioner; it will help you upon getting assistance or service if you ever need it. You will have then to provide the model and serial numbers of the air conditioner – these data are detailed on the rating plate of the unit.

Dealer name :

Address :

Model number :

Serial number :

Date of purchase :

WARRANTY