Great Stage Light GLM015 User Manual

90W SPOT MOVING HEAD

USER MANUAL

1

TABLE OF CONTENTS

1．BEFORE YOU BEGIN

WHAT IS INCLUDED

UNPACKING NSTRUCTIONS

MANUAL CONVENTIONS

ICONS

SAFETY INSTRUCTIONS

2．INSTRODUCTION

TECHNICAL SPECIFICATION

PRODUCT DIMENSIONS

PRODUCT OVERVIEW

3．SETUP

AC POWER

POWER LINKING

SIGNAL LINKING（DMX）

FUSE REPLACEMENT

MOUNTING ORIENTATION RIGGING

4. OPERATING INSTRUCTIONS

CONFIGURING THE STARTING ADDRESS

CONTROL PANEL FUNCTIONS

MENU MAP

DMX CHANNEL VALUES

5. APPENDIX

DMX PRIMER

GENERAL MAINTENANCE

FIXTURE LINKING

DATA CABLING

DMX DATA CABLE

CABLE CONNECTORS

3-PIN TO 5-PIN CONVERSION CHART

SETTING UP A DMX SERIAL DATA LINK

SETTING THE STARTING ADDRESS

GENERAL TROUBLESHOOTING

2

1. BEFORE YOU BEGIN

What is included

1 x Spot
1 x Mounting bracket and screws
1 x Power cable
1 x User Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the
contents to ensure that all parts are present, and have been received in good
condition. Notify the shipper immediately and retain packing material for
inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the
event that a fixture must be returned to the factory, it is important that the
fixture be returned in the original factory box and packing.

Manual Conventions

manuals use the following conventions to differentiate certain types of
information from the regular text.

Icons

This manual uses the following icons to indicate information that requires
special attention on the part of the user.

CONVENTION

MEANING

[10]

A LCD display to be configured

<Menu>

A key to be pressed on the fixture’s control panel

1~512

A range of values

50/60

A set of values of which only one can be chosen

Settings

A menu option not to be modified (for example,
showing the operating mode/current status)

MENU > Settings

A sequence of menu options to be followed

ON

A value to be entered or selected

3

Safety Instructions

● Please keep this User Manual for future consultation. If you sell the unit
to another user, be sure that they also receive this instruction booklet.

● Always make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the fixture.

● This product is intended for indoor use only! To prevent risk of fire or
shock, do not expose fixture to rain or moisture.

● Make sure there are no flammable materials close to the unit while
operating.

● The unit must be installed in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.

● Always disconnect from power source before servicing or replacing fuse
and be sure to replace with same fuse source.

● Secure fixture to fastening device using a safety chain.

● Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate
fixture at temperatures higher than this.

● In the event of a serious operating problem, stop using the unit
immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled
people can lead to damage or malfunction. Please contact the nearest

ICONS

MEANING

This paragraph contains critical installation, configuration or
operation information. Failure to comply with this
information may render the fixture partially or completely
inoperative, cause damage to the fixture or cause harm to
the user.

This paragraph contains important installation or
configuration information. Failure to comply with this
information may prevent the fixture from functioning
correctly.

This paragraph reminds you of useful, although not critical,
information

4

authorized technical assistance center.

● Never connect the device to a dimmer pack.

● Make sure the power cord is never crimped or damaged.

● Never disconnect the power cord by pulling or tugging on the cord.

● Never carry the fixture directly from the cord. Always use the
hanging/mounting bracket.

● Avoid direct eye exposure to the light source while it is on.

● Never carry the fixture by holding the head. Always use the carrying
handle.

2. I

NTRODUCTION

Technical Specification

1) Voltage: 100-240V,50-60Hz

2) Power consumption: 110W

3) LED: ultra bright 90W LED

4) LED color wheel: Basic 7 colors+ white, can adjust speed rainbow effect

5) Fixed gobo: 8 gobos+ white, Gobo rotating CW and CCW from slow to

fast), gobo shaking

6) Rotation gobo: 6 gobos + white, can bidirectional speed change

rotation, gobo shaking

7) Dimmer/Strobe: Dimmer, 1-20t/s

8) Focus: Electronic Focus

9) Pan::540° Tilt: 270

10) Control: DMX 512, 14/16 /11CHs

11) Working mode: Stand-alone mode, Controller mode, Master/Slave

synchronization mode

12) Other function: Pan/Tilt speed adjustable

Housing: High temperature resistant engineering plastic + aluminum

alloy.

13) Weight: 6.5KG

14) Product Size: 240*240*370mm

15) Packing Size: 350*340*375mm

5

Product Dimensions

6

Product Overview