Great Plains Reel User Manual

Page 1

10/20/2005

586-167M

Assembly Instructions for the Reel Following the Rolling Harrow

Mount the reel arm assemblies (589-069L) to the drag frames, using the dimensions in the
layouts provided, using a 5/8x3x4 ½ u-bolt (806-183C) with a lock washer and nut. Assemble the reel
sub-assemblies to the reel tube by u-bolting the reel brackets to the correct tube with a 5/8x2 1/2x3 ¾ u­bolt (806-182C), lock washer, and nut. If you are assembling a 10’ or 12’ reel, do not install the two
center u-bolts as you will use 5/8x4 hex bolts (802-060C), with lock washers and nuts in this location as
shown in bubble labeled double reel center mounting on parts breakdown page. Once the reels are
attached to the reel bar, bolt the reel bar to the reel arm assemblies using the dimensions provided on the
layouts. If you are bolting on a 10’ or 12’ section; by using the 5/8x4 bolts as shown in figure 5 the reel
should be in the proper location if installed correctly. If the reels between the center section and the
wing sections are closer than 5”, recheck the reel arm dimensions and adjust accordingly.

Mount the rear stand bracket (580-049H), if applicable, to the drag frame with 5/8x3x4 ½ u­bolts, a lock washer and a nut. The rear stand leg (560-196H) should be pinned in the rear stand bracket
with a 3/4x4 ½ pin and retainer (805-081C).

Note: For Turbo-Till models 2200 and 3000 reel following rolling harrow attachment, add wing
weights by removing the bolt on end caps from the front wing gang bars and sliding in weights provided
(1/2” x 5” flat).

Page 2

Great Plains Mfg., Inc.

y

Page 3

Reel Following Rolling Harrow Assembl

Ref # GP Part # Description Comments

1. 589-059H Reel Mounting Bracket (3" Tube)

2. 589-060H Reel Mounting Arm

3. 575-516H Spring Bolt, 3/4" x 22 1/4" Long

4. 575-273D Tube, 3 1/2' Reel Assy 1700TT (Vers. I), 1700TT (Vers. II) & 4000TT

575-093D Tube, 6' Reel Assy 2200TT
575-096D Tube, 9' Reel Assy 1000TT, 1700TT (Version I)
575-097D Tube, 10' Reel Assy 1700TT (Vers. II), 2200TT, 3000TT, & 4000TT
575-099D Tube, 12' Reel Assy 1200TT & 4000TT

5. 575-525H 3 1/2' Reel Weldment 1000TT, 1700TT (Version I & II), 4000TT
575-526H 5' Reel Weldment
575-527H 6' Reel Weldment 1200TT & 4000TT

6. 575-521H Reel Mounting Bracket

7. 804-024C Flat Washer, 3/4

8. 807-225C Spring Comp. 1 3/4 OD x 5/16 W x 11 Long

9. 807-226C Spring Comp. 1 13/16 OD x 3/8 W x 2 3/4 Long

10. 803-026C Lock Nut, 3/4

11. 802-768C Eye Bolt, 3/4 x 6 1/2

12. 803-048C Jam Nut, 3/4

13. 802-192C Hex Bolt, 3/4 x 4 1/2

14. 589-102D Replaceable Swivel

15. 802-767C Shoulder Bolt, 5/8 x 1 3/4 Special

16. 589-252V Replaceable Swivel w/Bolts Includes items 14 & 15

17. 802-066C Hex Bolt, 3/4 x 3 1/2

18. 575-141D Reel Bearing Spacer

19. 804-023C Lock Washer, 3/4

20. 805-140C Clevis Pin, 3/4 x 2 1/2

21. 805-225C Cotter Pin, 1/8 x 1 1/2

22. 806-179C U-Bolt, 5/8 x 4 1/32 x 4 1/4

23. 806-182C U-Bolt, 5/8 x 2 17/32 x 3 1/2

24. 802-060C Hex Bolt, 5/8 x 4

25. 804-022C Lock Washer, 5/8

26. 803-021C Hex Nut, 5/8

27. 802-128C Hex Bolt, 1/2 x 2

28. 816-429C Rubber Spacer

29. 804-017C Flat Washer, 1/2

30. 589-085D Zerk Guard

31. 803-342C Top Lock Nut, 1/2

32. 822-208C Bearing Flange 1 1/2 ID RD 5 Inch Square

Page 4