Page 1
Table of Contents Part Number Index
Parts Manual
No-Till Air Drill Implement
NTA3010 & NTA3510
Read the Operator's manual entirely. When you see this symbol, the subsequent
instructions and warnings are serious - follow without exception.Your life and the
lives of others depend on it!
16178
Cover illustration may show optional equipment not supplied with standard unit.
© Copyright 2013 Printed 04/10/13 160-219P
Page 2
Table of Contents Part Number Index
Table of Contents
Section 1: Introduction.................................................4
Using This Manual...............................................................4
Manual Replacement Information.......................................4
Manual Revisions................................................................4
Touch-up Paint....................................................................4
Hardware Legend................................................................5
Replacement Hardware......................................................5
Serial Numbers...................................................................5
Part Number Service Coding..............................................5
Frames............................................................................6
Center Frame To Rockshaft.................................................6
Left Wing To Center.............................................................8
Right Wing To Center........................................................10
Cart Hook-Up for ADC2220 Air Drill Cart..........................12
Cart Hook-Up for ADC2350 Air Drill Cart..........................14
Harness & Light Kit for ADC2220 Air Drill Cart.................16
Harness & Light Kit for ADC2350 Air Drill Cart.................18
Slow Moving Vehicle Emblem...........................................20
Gauge Wheels..............................................................22
Dual Gauge Wheel............................................................22
Gauge Wheel And Tire......................................................24
Parallel Arm Dual Gauge Wheel.......................................26
Parallel Arm Lift Assembly................................................28
Openers........................................................................30
Parallel Arm Opener..........................................................30
Coulter (S/N Z1148-).........................................................32
Coulter (S/N Z1149+)........................................................34
Grease Bank.....................................................................36
Press Wheels...............................................................38
1" x 12" Double "V" Press Wheel......................................38
2" x 13" Single Press Wheel..............................................40
3" x 13" Single Press Wheel..............................................42
3" x 14" Peaked Single Press Wheel.................................44
Hydraulics....................................................................46
Folding Hydraulics.............................................................46
Depth Stop Valve Assembly..............................................48
Hydraulic Cylinder (810-221C)..........................................50
Hydraulic Cylinder (810-287C)..........................................52
Hydraulic Cylinder (810-332C)..........................................54
Hydraulic Cylinder (810-333C)..........................................56
Hydraulic Shut-Off Valve (810-084C)................................58
NTA Control Valve (S/N Z1101+).......................................60
Pressure Reducing Valve (810-349C)...............................62
Relief & Solenoid Valves...................................................64
Relief Valve (810-348C)....................................................66
Relief Valve (810-370C)....................................................68
Solenoid Valve (810-342C)...............................................70
Stroke Control Valve (810-445C).......................................72
Transport Hydraulics (RDIF Cartridge)..............................74
Transport Hydraulics (RPIL Car tridge)..............................76
Monitor.........................................................................78
Blockage Monitor (Option)................................................78
Agtron Sensor (Option) (S/N Z1263-)...............................80
Agtron AGS25 Blockage Sensor (Option) (S/N Z1264+)...82
Implement Kit....................................................................84
Monitor NTA3010..............................................................86
Monitor NTA3510..............................................................88
Towers..........................................................................90
Tower for ADC2220 Air Cart Drill......................................90
Tower for ADC2350 Air Cart Drill......................................92
Decals...........................................................................94
Decal Placement...............................................................94
Options.........................................................................96
Coulter Tine.......................................................................96
Harrow Assembly..............................................................98
Harrow Center Mount......................................................100
Harrow Wing Mount.........................................................102
Spring Scraper Assembly................................................104
Weights (160-296S)........................................................106
Part Number Index.....................................................108
© Copyright 2013 All rights reserved Printed 04/10/13
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from
the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes
the state of this product at the time of its publication, and may not reflect the product in the future.
The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains
All other brands and product names are trademarks or registered trademarks of their respective holders.
160-219P - 2 - 04/10/13
Great Plains Manufacturing, Incorporated Trademarks
Printed in the United States of America.
Page 3
Table of Contents Part Number Index
Alphabetized Table of Contents
Selected Models
1
1" x 12" Double "V" Press Wheel.................................38
2
2" x 13" Single Press Wheel.........................................40
3
3" x 13" Single Press Wheel.........................................42
3" x 14" Peaked Single Press Wheel............................44
A
Agtron AGS25 Blockage Sensor (Option) (S/N
Z1264+).................................................................82
Agtron Sensor (Option) (S/N Z1263-)..........................80
B
Blockage Monitor (Option)............................................78
C
Cart Hook-Up for ADC2220 Air Drill Cart.....................12
Cart Hook-Up for ADC2350 Air Drill Cart.....................14
Center Frame To Rockshaft............................................6
Coulter (S/N Z1148-)....................................................32
Coulter (S/N Z1149+)...................................................34
Coulter Tine..................................................................96
L
Left Wing To Center........................................................8
M
Monitor NTA3010.........................................................86
Monitor NTA3510.........................................................88
N
NTA Control Valve (S/N Z1101+)..................................60
P
Parallel Arm Dual Gauge Wheel...................................26
Parallel Arm Lift Assembly...........................................28
Parallel Arm Opener.....................................................30
Pressure Reducing Valve (810-349C)..........................62
R
Relief & Solenoid Valves..............................................64
Relief Valve (810-348C)...............................................66
Relief Valve (810-370C)...............................................68
Right Wing To Center...................................................10
S
Slow Moving Vehicle Emblem.......................................20
Solenoid Valve (810-342C)...........................................70
Spring Scraper Assembly...........................................104
Stroke Control Valve (810-445C)..................................72
D
Decal Placement..........................................................94
Depth Stop Valve Assembly.........................................48
Dual Gauge Wheel.......................................................22
F
Folding Hydraulics........................................................46
G
Gauge Wheel And Tire.................................................24
Grease Bank................................................................36
H
Harness & Light Kit for ADC2220 Air Drill Cart............16
Harness & Light Kit for ADC2350 Air Drill Cart............18
Harrow Assembly.........................................................98
Harrow Center Mount.................................................100
Harrow Wing Mount....................................................102
Hydraulic Cylinder (810-221C).....................................50
Hydraulic Cylinder (810-287C).....................................52
Hydraulic Cylinder (810-332C).....................................54
Hydraulic Cylinder (810-333C).....................................56
Hydraulic Shut-Off Valve (810-084C)...........................58
I
Implement Kit...............................................................84
T
Tower for ADC2220 Air Cart Drill..................................90
Tower for ADC2350 Air Cart Drill..................................92
Transport Hydraulics (RDIF Car tr idge).........................74
Transport Hydraulics (RPIL Car tridge).........................76
W
Weights (160-296S)...................................................106
04/10/13 - 3 - 160-219P
Page 4
Table of Contents Part Number Index
160-219P - 4 - 04/10/13
Page 5
Table of Contents Part Number Index
04/10/13 - 5 - 160-219P
Page 6
Table of Contents Part Number Index
Center Frame To Rockshaft
(Applies to NTA3010, NTA3510 only)
16296
160-219P - 6 - 04/10/13
Page 7
Table of Contents Part Number Index
Center Frame To Rockshaft
(Applies to NTA3010, NTA3510 only)
Image No.dwg16296
BOLT WHEEL 1/2-20X1 90-DEG802-104C1.
HUB & SPINDLE 6 BOLT 4570 LB815-090C2.
NUT HEX NYLOCK 5/8-11 PLT803-148C3.
HHCS 5/8-11X3 3/4 GR5802-153C4.
GREASE ZERK STRAIGHT 1/4-28800-001C5.
NTA 35' ROCKSHAFT WELDMENT161-074H6.
WING PIVOT PIN WELDMENT160-201H7.
PIN ROLL 3/8 X 2 PLT805-249C8.
SCREW RD HD 10-24 X 1 PLT801-055C9.
NTA CLUTCH/SOLENOID SWITCH823-157C10.
WASHER FLAT #10 SAE PLT804-046C11.
WASHER INTERNAL STAR #10 PLT804-004C12.
NUT HEX 10-24 PLT803-001C13.
PIN HITCH 1 X 3 3/8 USABLE LG805-007C14.
NTA35 TRANSPORT LOCK161-108H15.
PIN CLEVIS 1 X 3 11/16 GR5 PLT805-124C16.
CYL REP 4.75 X 12 X 1.50 ROD810-287C17.
WASHER FLAT 1 SAE804-029C18.
PIN COTTER 3/16 X 1 3/4 PLT805-017C19.
NTA35 CENTERFRAME WELDMENT160-200H20.
ELE. CLUTCH SWITCH CAM CLAMP890-433C21.
BUSHING CYL 1 1/4 X 1 X 1890-005C22.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C23.
PIN CLEVIS 1 X 3 5/16 HRD PLT805-239C24.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 7 - 160-219P
Page 8
Table of Contents Part Number Index
Left Wing To Center
(Applies to NTA3010, NTA3510 only)
16285
160-219P - 8 - 04/10/13
Page 9
Table of Contents Part Number Index
Left Wing To Center
(Applies to NTA3010, NTA3510 only)
Image No.dwg16285
WING PIVOT PIN WELDMENT160-201H1.
PIN ROLL 3/8 X 2 PLT805-249C2.
PIN COTTER 7/32 X 2805-060C3.
WASHER FLAT 1 1/4 SAE PLT804-039C4.
PIN CLEVIS 1 1/4 X 3 3/8 GR5805-196C5.
NUT HEX 1/2-13 PLT803-020C6.
WASHER LOCK SPRING 1/2 PLT804-015C7.
NTA MARKER FOLD CYL STOP113-612D8.
HHCS 1/2-13X3 3/4 GR5802-042C9.
CYL 4.5X41.75X2 ROD810-332C10.
NUT HEX 1-8 PLT803-031C11.
WASHER LOCK SPRING 1 PLT804-027C12.
NTA MARKER WING FOLD STOP113-609D13.
HHCS 1-8X7 GR5802-075C14.
PIN HITCH 1 X 6 W/HAIRPIN805-033C15.
NTA35 CENTERFRAME WELDMENT160-200H16.
NTA35 LH WING WELDMENT160-204H17.
GREASE ZERK STRAIGHT 1/4-28800-001C18.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C19.
HHCS 5/16-18X2 1/2 GR5802-172C20.
WASHER LOCK SPRING 5/16 PLT804-009C21.
RPBY 196-146D196-112D22.
HHCS 5/16-18X1 1/4 GR5802-010C23.
HOSE CLIP 13/16 ID800-064C24.
NTA30 LH WING WELDMENT160-234H25.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 9 - 160-219P
Page 10
Table of Contents Part Number Index
Right Wing To Center
(Applies to NTA3010, NTA3510 only)
16290
160-219P - 10 - 04/10/13
Page 11
Table of Contents Part Number Index
Right Wing To Center
(Applies to NTA3010, NTA3510 only)
Image No.dwg16290
WING PIVOT PIN WELDMENT160-201H1.
PIN ROLL 3/8 X 2 PLT805-249C2.
PIN COTTER 7/32 X 2805-060C3.
WASHER FLAT 1 1/4 SAE PLT804-039C4.
PIN CLEVIS 1 1/4 X 3 3/8 GR5805-196C5.
NUT HEX 1/2-13 PLT803-020C6.
WASHER LOCK SPRING 1/2 PLT804-015C7.
NTA MARKER FOLD CYL STOP113-612D8.
HHCS 1/2-13X3 3/4 GR5802-042C9.
CYL 4.5X41.75X2 ROD810-332C10.
NUT HEX 1-8 PLT803-031C11.
WASHER LOCK SPRING 1 PLT804-027C12.
NTA MARKER WING FOLD STOP113-609D13.
HHCS 1-8X7 GR5802-075C14.
PIN HITCH 1 X 6 W/HAIRPIN805-033C15.
NTA35 CENTERFRAME WELDMENT160-200H16.
NTA35 RH WING WELDMENT160-205H17.
GREASE ZERK STRAIGHT 1/4-28800-001C18.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C19.
HHCS 5/16-18X1 1/4 GR5802-010C20.
WASHER LOCK SPRING 5/16 PLT804-009C21.
RPBY 196-146D196-112D22.
NTA30 RH WING WELDMENT160-235H23.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 11 - 160-219P
Page 12
Table of Contents Part Number Index
Cart Hook-Up for ADC2220 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
16311
160-219P - 12 - 04/10/13
Page 13
Table of Contents Part Number Index
Cart Hook-Up for ADC2220 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
Image No.dwg16311
NTA CART LINK PIN WELDMENT160-202H1.
PIN ROLL 3/8 X 2 PLT805-249C2.
GREASE ZERK 1/4-28 X 90-DEG800-073C3.
NTA CENT. CART LINK PIN WLDMNT160-203H4.
NTA CARTLINK WELDMENT160-210H5.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C6.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 13 - 160-219P
Page 14
Table of Contents Part Number Index
Cart Hook-Up for ADC2350 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
26376
160-219P - 14 - 04/10/13
Page 15
Table of Contents Part Number Index
Cart Hook-Up for ADC2350 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
Image No.dwg26376
NTA35 CENTERFRAME WELDMENT160-200H1.
NTA CART LINK PIN WELDMENT160-202H2.
PIN ROLL 3/8 X 2 PLT805-249C3.
PULL BAR WELDMENT160-023H4.
PIN HITCH 1 1/4 X 4 1/2805-119C5.
NUT HEX 5/8-11 PLT803-021C6.
HHCS 5/8-11X1 GR5 NYL802-049C7.
WASHER LOCK SPRING 5/8 PLT804-022C8.
PIN HAIR COTTER .243 WIRE PLT805-167C9.
PULL LINK WELDMENT160-022H10.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C11.
NTA CENT. CART LINK PIN WLDMNT160-203H12.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 15 - 160-219P
Page 16
Table of Contents Part Number Index
Harness & Light Kit for ADC2220 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
16369
160-219P - 16 - 04/10/13
Page 17
Table of Contents Part Number Index
Harness & Light Kit for ADC2220 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
Image No.dwg16369
RPBY 823-194CVA-4907031.
PEDESTAL SAFETY LAMP AMBER890-607C2.
PEDESTAL SAFETY LAMP RED890-606C3.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 17 - 160-219P
Page 18
Table of Contents Part Number Index
Harness & Light Kit for ADC2350 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
26378
160-219P - 18 - 04/10/13
Page 19
Table of Contents Part Number Index
Harness & Light Kit for ADC2350 Air Drill Cart
(Applies to NTA3010, NTA3510 only)
Image No.dwg26378
NTA35 CENTERFRAME WELDMENT160-200H1.
LIGHT KIT ADC IMPLEMENT833-462C2.
SCR HEX SELF TAP 1/4-20X1TYPEF801-151C3.
WESBAR SNGL AG LAMP, AMBER/AMB26064.
WESBAR SNGL AG LAMP, RED/BLANK26105.
NUT HEX FLANGE 3/8-16 PLT803-068C6.
NTA LIGHT BRACKET160-506D7.
U-BOLT 3/8-16 X 6 1/32 X 5 PLT806-022C8.
WASHER LOCK #6 SS804-050C9.
WASHER FLAT #6 PLT804-109C10.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 19 - 160-219P
Page 20
Table of Contents Part Number Index
Slow Moving Vehicle Emblem
(Applies to NTA3010, NTA3510 only)
16294
160-219P - 20 - 04/10/13
Page 21
Table of Contents Part Number Index
Slow Moving Vehicle Emblem
(Applies to NTA3010, NTA3510 only)
Image No.dwg16294
NTA35 CENTERFRAME WELDMENT160-200H1.
WASHER LOCK SPRING 5/16 PLT804-009C2.
HHCS 5/16-18X3/4 GR5802-007C3.
SMV MOUNTING BLADE890-153C4.
NUT-HEX 1/4-20 PLT803-006C5.
WASHER LOCK SPRING 1/4 PLT804-006C6.
DECAL SLOW MOVING-GALV. BACKED818-055C7.
SCREW RD HD 1/4-20 X 5/8801-018C8.
Frames
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 21 - 160-219P
Page 22
Table of Contents Part Number Index
Dual Gauge Wheel
(Applies to NTA3010, NTA3510 only)
16331
160-219P - 22 - 04/10/13
Page 23
Table of Contents Part Number Index
Dual Gauge Wheel
(Applies to NTA3010, NTA3510 only)
Image No.dwg16331
NTA WING GAUGE WHEEL WLDMNT RH161-076H2.
NTA WING GAUGE WHEEL WLDMNT LH161-077H2.
GREASE ZERK STRAIGHT 1/4-28800-001C3.
PIN CLEVIS 1 X 3 1/8 GR5 PLT805-159C4.
WASHER FLAT 1 SAE804-029C5.
PIN COTTER 3/16 X 1 3/4 PLT805-017C6.
CYL REP 4.25X12X1.5 ROD (TIE)810-221C7.
PIN ROLL 3/8 X 2 PLT805-249C8.
WING PIVOT PIN WELDMENT160-201H9.
BUSHING CYL 1 1/4 X 1 X 1890-005C10.
NTA35 WING EYEBOLT WELDMENT161-107H11.
NUT HEX JAM 1 1/4-7 PLT803-032C12.
WASHER LOCK 1 1/4 SPRING PLT804-030C13.
NUT HEX 1 1/4-7 PLT803-034C14.
SEAL 2.56X1.625X.438 CR16289816-011C15.
BRG CONE 1.50ID LM-29749822-018C16.
BRG CUP LM-29710822-019C17.
HUB 6 BOLT4 5/8 PILOT W/ CUPS815-082C18.
BEARING CUP LM-67010822-020C19.
BEARING CONE LM-67048822-021C20.
BOLT WHEEL 1/2-20X1 90-DEG802-104C21.
HUB GREASE CAP200-001D22.
WASHER SPINDLE - 7/8804-055C23.
PIN COTTER 5/32 X 1 3/4 LG805-246C24.
NUT HEX SLOTTED 7/8-14 PLT803-029C25.
VALVE STEM TR415X.625X1 1/4 LG816-035C26.
TIRE 11L-15SL 12 PLY TUBELESS814-031C27.
WHEEL 15 DIA X 10 WIDE X 6 BLT814-023C28.
TRANSPORT WHEEL & TIRE ASSY155-012K29.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C30.
PIN CLEVIS 1 X 3 5/16 HRD PLT805-239C31.
Gauge Wheels
RevisionCommentsPart DescriptionPart No.Ref.
Includes items 15-20 & 22HUB 6 BOLT4 5/8 PILOT 3600 LB815-077C1.
04/10/13 - 23 - 160-219P
Page 24
Table of Contents Part Number Index
Gauge Wheel And Tire
(Applies to NTA3010, NTA3510 only)
16357
160-219P - 24 - 04/10/13
Page 25
Table of Contents Part Number Index
Gauge Wheel And Tire
(Applies to NTA3010, NTA3510 only)
Image No.dwg16357
HFS 1/2-20X1 1/2 GR5802-399C1.
TRANSPORT WHEEL & TIRE ASSY155-012K2.
HUB GREASE CAP200-001D3.
NUT HEX SLOTTED 7/8-14 PLT803-029C4.
PIN COTTER 3/16 X 1 1/4 PLT805-016C5.
7/8 SPINDLE WASHER, HARDENED181-064D6.
BEARING CONE LM-67048822-021C7.
BEARING CUP LM-67010822-020C8.
HUB 6 BOLT4570# W/CUPS PAINTD815-094C9.
BRG CUP 2.89ODX.58WD #LM501310822-053C10.
BRG CONE 1.62IDX.78WD#LM501349822-048C11.
SEAL 1.875 ID X 3.00 OD QDS816-265C12.
SPINDLE SGL 1.98X11.00815-089C13.
SPINDLE ASSY SGL 1.98X11815-096C15.
WHEEL REINFORCING RING152-215D16.
Gauge Wheels
RevisionCommentsPart DescriptionPart No.Ref.
Includes items 3-7,9,11,&12HUB 6 BOLT4570# ASY LESS BLTS815-097C14.
04/10/13 - 25 - 160-219P
Page 26
Table of Contents Part Number Index
Parallel Arm Dual Gauge Wheel
(Applies to NTA3010, NTA3510 only)
16351
160-219P - 26 - 04/10/13
Page 27
Table of Contents Part Number Index
Parallel Arm Dual Gauge Wheel
(Applies to NTA3010, NTA3510 only)
Image No.dwg16351
RPBY 161-132H161-127H2.
PIVOTTHRUST WASHER804-102C3.
NTA CASTER RETAINER CAP161-231D4.
WASHER LOCK SPRING 1/2 PLT804-015C5.
HHCS 1/2-13X1 1/4 GR5802-034C6.
STEEL BUSHING 3 1/4X3IDX3LONG890-193C7.
BOLT WHEEL 1/2-20X1 90-DEG802-104C8.
HHCS 5/8-11X3 3/4 GR5802-153C9.
NUT LOCK 5/8-11 PLT803-024C10.
SPINDLE SGL 1.98X11.00815-089C11.
BEARING CUP LM-67010822-020C14.
BRG CUP 2.89ODX.58WD #LM501310822-053C15.
SEAL 1.875 ID X 3.00 OD QDS816-265C16.
BRG CONE 1.62IDX.78WD#LM501349822-048C17.
BEARING CONE LM-67048822-021C18.
HUB GREASE CAP200-001D19.
7/8 SPINDLE WASHER, HARDENED181-064D20.
PIN COTTER 3/16 X 1 1/4 PLT805-016C21.
NUT HEX SLOTTED 7/8-14 PLT803-029C22.
Gauge Wheels
RevisionCommentsPart DescriptionPart No.Ref.
Includes 11-22.HUB & SPINDLE 6 BOLT 4570 LB815-090C1.
Includes 16-19.HUB 6 BOLT4570# ASY LESS BLTS815-097C12.
Includes 14,15.HUB 6 BOLT 4570# W/CUPS PAINTD815-094C13.
04/10/13 - 27 - 160-219P
Page 28
Table of Contents Part Number Index
Parallel Arm Lift Assembly
(Applies to NTA3010, NTA3510 only)
16353
160-219P - 28 - 04/10/13
Page 29
Table of Contents Part Number Index
Parallel Arm Lift Assembly
(Applies to NTA3010, NTA3510 only)
Image No.dwg16353
HHCS 1-8X12 1/4 GR8802-638C1.
WASHER LOCK SPRING 1 PLT804-027C2.
NUT HEX 1-8 PLT803-031C3.
GREASE ZERK STRAIGHT 1/4-28800-001C4.
REAR LIFT CASTER WELDMENT - RH161-101H7.
REAR LIFT CASTER WELDMENT - LH161-102H7.
PIN COTTER 3/16 X 1 3/4 PLT805-017C8.
WASHER FLAT 1 SAE804-029C9.
WASHER LOCK 1 1/4 SPRING PLT804-030C10.
NUT HEX 1 1/4-7 PLT803-034C11.
NTA REAR EYEBOLT WELDMENT161-121H12.
BUSHING CYL 1 1/4 X 1 X 1890-005C13.
SPACER 1.5X1.032X1.5161-221D14.
REAR LIFT CASTER CYLINDER PIN161-211D15.
SPRING ADJUSTMENT TOOL WELD198-126H16.
PIN HAIR COTTER .148 WIRE805-032C17.
CYLINDER LCK CHNL 1 1/2X11 1/2161-118H18.
PIN CLEVIS 1 X 3 11/16 GR5 PLT805-124C21.
CYL REP 4.5X12X1.5 ROD 22.25L810-333C22.
HHCS 1/2-13X2 GR5802-128C23.
WASHER FLAT 1/2 SAE PLT804-016C24.
NTA CASTER PIVOT BOLT HOLDER161-238D25.
WASHER LOCK SPRING 1/2 PLT804-015C26.
NUT HEX 1/2-13 PLT803-020C27.
Gauge Wheels
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.NTA CASTER ARM SPACER TUBE161-246D5.
1st rev.RR LIFT CSTR LINKARM SPACER TB161-210D5.
2nd rev.CASTER PARALLEL ARM LARGE PVT161-128H6.
1st rev.Formerly 161-103HCASTER ARM SINGLE REPLACEMENT161-129A6.
Formerly 805-152CPIN 3/8 X 3 USABLE LW/PIN805-001C19.
2nd rev.BUSHING 1 7/8X1 5/8X1 1/2 SPLT890-666C20.
1st rev.BUSHING 1 1/2 X 1 1/4 X 1 1/2890-122C20.
Part for Field Update KitCASTER FIELD PLATE161-247D28.
Part for Field Update KitHHCS 1-8X13 5/8 GR8802-666C29.
04/10/13 - 29 - 160-219P
Page 30
Table of Contents Part Number Index
Parallel Arm Opener
(Applies to NTA3010, NTA3510 only)
16361
160-219P - 30 - 04/10/13
Page 31
Table of Contents Part Number Index
Parallel Arm Opener
(Applies to NTA3010, NTA3510 only)
Image No.dwg16361
DD BRG FLANGE DUST COVER107-111D1.
D.D. SLOTTED SCRAPER107-113D2.
RPBY 107-135S107-133S3.
PW ADJUSTMENT TRUNNION ASSY122-202S4.
TOP PARALLEL ARM WELDMENT198-089H5.
BOTTOMPARALLEL ARM WELDMENT198-090H6.
SPRING ADJUST PLATE LH198-127D7.
SPRING ADJUST PLATE RH198-128D8.
SPRING ADJUST PIVOT TUBE198-134D9.
REAR PARALLEL ARM PIVOT TUBE198-139D10.
FRONT PARALLELARM PIVOT TUBE198-140D11.
PARALLEL LINKAGE OPENER WELD198-409H12.
PARALLEL ARM OPENER MOUNT198-436H13.
SCREW HEX SLT10-16X1/2P.THD CT801-002C14.
RHSNB 3/8-16X1 GR5802-015C15.
HHCS 3/8-16X3 1/2 GR5802-147C16.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C17.
HFS 1/2-13 X 5 1/2802-420C18.
HFS 1/2-13 X 5 1/4802-648C19.
NUT HEX 3/8-16 PLT803-014C20.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C21.
WASHER FLAT 3/8 SAE PLT804-012C22.
WASHER LOCK SPRING 3/8 PLT804-013C23.
WASHER MACH 1.19 X .63 X 18GA804-040C24.
SPRING EXT 1 5/8OD X 6.6X.177807-116C25.
CASTING SPRING ADJUST812-204C26.
PARALLEL ARM PIVOT BUSHING817-084C27.
RHSNB 5/8-11X4 GR5802-193C29.
U-BOLT 5/8-11 X 2 1/32 X 2 GR5806-149C30.
PARALLEL OPENER MOUNT PLATE198-210D31.
WASHER LOCK SPRING 5/8 PLT804-022C32.
NUT HEX 5/8-11 PLT803-021C33.
RPBY 817-328C198-104D34.
PIN ROLL 5/32 X 5/8 PLT805-186C35.
OPENER TRUNION817-347C37.
SPRING .540 O.D.X1 1/4 X.054W807-106C38.
PIN CLEVIS 3/8 X 2 1/8 USABLE805-154C39.
AIR DRILL DD OPNR HOSE BOOT816-352C40.
TOP PARALLEL ARM OFFSET WELDMT198-437H41.
BOTTOMPARALLEL ARM RH OFFSET198-438H42.
BOTTOMPARALLEL ARM LH OFFSET198-439H42.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Includes items 34, 35, 37, 38 and 39.
S/N Z1118- also includes item 5.
Model year 1998-PLASTIC OPENER SEED TUBE817-133C28.
(S/N Z1118-)Useonlywith812-194C.PRESS WHEEL ARM BUMPER817-132C36.
2nd rev.(S/NZ1119+)Replaces812-194Cand
item 5.
Use existing stock; 1st rev.(S/N Z1118-)RPBY 817-347C812-194C37.
Model year 1999+OPENER SEED TUBE, PLASTIC817-314C43.
Model year 1999+HEX SEED FLAP MOUNTING CLIP121-164D44.
Model year 1999+SEED FLAP, RUBBER, SEED-LOK816-302C45.
Model year 1999+SEED FLAP & HEX CLIP, SEEDLOK122-242S46.
04/10/13 - 31 - 160-219P
Page 32
Table of Contents Part Number Index
Coulter (S/N Z1148-)
(Applies to NTA3010, NTA3510 only)
16358
160-219P - 32 - 04/10/13
Page 33
Table of Contents Part Number Index
Coulter (S/N Z1148-)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16358
WASHER FLAT 1 1/4 SAE PLT804-039C3.
PIN COTTER 1/4 X 2 PLT805-021C4.
COULTER SPRING ROD WLDMT204-075H5.
NUT HEX JAM 3/4-10 PLT803-048C6.
SPRING 2.25 O.D.X .5 COIL149-559D7.
SPRING ROD SLEEVE 1 1/8 OD204-107D8.
COULTER SPRING WASHER149-558D9.
GREASE ADAPT 1/4-28M X 1/4 TB800-211C10.
BUSHING COULTER CASTING817-029C11.
COULT. SPRING BAR204-272D12.
HHCS 7/8-9X2 3/4 GR5802-103C13.
WASHER LOCK SPRING 7/8 PLT804-037C14.
NUT HEX 7/8-9 PLT803-049C15.
RHSNB 1/2-13X1 1/4 GR5802-214C16.
OIL-SEAL DOUBLE LIP816-009C17.
BEARING CONE LM-67048822-021C18.
BEARING CUP LM-67010822-020C19.
HUB GREASE CAP200-001D21.
GREASE ZERK STRAIGHT 1/4-28800-001C22.
COULTER HUB PACKAGE200-002S23.
PIN COTTER 3/16 X 1 3/4 PLT805-017C24.
COULTER BLADE FLUTED820-018C25.
17 COULTER BLADE 5/8 WAVY820-116C25.
17 COULTER BLADE 3/4 WAVY820-082C25.
5/8 WAVY TURBO BLADE820-156C25.
WASHER LOCK SPRING 1/2 PLT804-015C26.
NUT HEX 1/2-13 PLT803-020C27.
WASHER SPINDLE - 7/8804-055C28.
NUT HEX SLOTTED 7/8-14 PLT803-029C29.
U-BOLT 5/8-11 X 4 1/32 X 4806-106C30.
COULTER CLAMP BAR149-059D31.
NUT HEX 5/8-11 PLT803-021C32.
SWING ARM BUSHING817-051C33.
NUT HEX FLANGE LOCK 3/4-10 PLT803-181C36.
HHCS 1/2-13X1 3/4 GR5802-082C37.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.RPBY 249-136A149-962S1.
1st rev.RPBY 149-962S149-006D1.
2nd rev.FERT COULTERSWING ARM149-181E2.
Use existing stock; 1st rev.RPBY 149-181E149-928E2.
USED IN OFFSET COULTER ASSYFERT COULTERSWING ARM149-181E2.
2nd rev.Includes hub and items 19 and 22.COULTER HUB & CUP ASSY200-039V20.
1st rev.RPBY 200-039V200-002D20.
USED IN OFFSET COULTER ASSYOFFSET COULTER MOUNT PLATE149-086D34.
USED IN OFFSET COULTER ASSYOFFSET COULTER BRKT F/LH BOX197-010D35.
04/10/13 - 33 - 160-219P
Page 34
Table of Contents Part Number Index
Coulter (S/N Z1149+)
(Applies to NTA3010, NTA3510 only)
21715
160-219P - 34 - 04/10/13
Page 35
Table of Contents Part Number Index
Coulter (S/N Z1149+)
(Applies to NTA3010, NTA3510 only)
Image No.dwg21715
CLTR CASTING ASSY249-050S1.
CLTR SWING ARM WLMT249-051H2.
OFFSET COULTER MOUNT PLATE149-086D3.
EYE BOLT 3/4-10X14 3/4 LG SP802-718C4.
COULTER SPRING GUIDE TUBE805-331C5.
GREASE ADAPT 1/4-28M X 1/4 TB800-211C6.
HHCS 7/8-9X2 3/4 GR5802-103C7.
COULTER HUB & CUP ASSY200-039V8.
HUB GREASE CAP200-001D9.
NUT HEX SLOTTED 7/8-14 PLT803-029C10.
NUT HEX JAM 3/4-10 PLT803-048C11.
NUT HEX 7/8-9 PLT803-049C12.
BUSHING 1X3/4X1 1/8 FLG HD817-513C13.
OIL-SEAL DOUBLE LIP816-009C14.
BEARING CONE LM-67048822-021C15.
WASHER LOCK SPRING 7/8 PLT804-037C16.
WASHER MACH 1 7/8X1 1/4X 14GA804-165C17.
WASHER SPINDLE - 7/8804-055C18.
PIN COTTER 3/16 X 1 3/4 PLT805-017C19.
SNAP RING EXT 1 1/4 HEAVY800-177C20.
COULT. SPRING BAR204-272D21.
SPRING 2.25 O.D.X .5 COIL149-559D22.
SNAP RING 3/4 EXTERNAL HEAVY800-164C23.
COULTER SPRING WASHER149-558D24.
WASHER MACH 1 1/4X3/4X14GA804-156C25.
RHSNB 1/2-13X1 1/4 GR5802-214C26.
WASHER LOCK SPRING 1/2 PLT804-015C27.
NUT HEX 1/2-13 PLT803-020C28.
COULTER BLADE FLUTED820-018C29.
17 COULTER BLADE 5/8 WAVY820-116C29.
17 COULTER BLADE 3/4 WAVY820-082C29.
COULTER CLAMP BAR149-059D30.
WASHER LOCK SPRING 5/8 PLT804-022C31.
NUT HEX 5/8-11 PLT803-021C32.
HHCS 3/8-16X6 1/2 GR5802-028C33.
OFFSET COULTER BRKT F/LH BOX197-010D34.
U-BOLT 5/8-11 X 4 1/32 X 4806-106C35.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Factory Installed18 INCH TURBO COULTER BLADE820-215C29.
04/10/13 - 35 - 160-219P
Page 36
Table of Contents Part Number Index
Grease Bank
(Applies to NTA3010, NTA3510 only)
16360
160-219P - 36 - 04/10/13
Page 37
Table of Contents Part Number Index
Grease Bank
(Applies to NTA3010, NTA3510 only)
Image No.dwg16360
GREASE ZERK STRAIGHT 1/8-27NPT800-130C1.
AD PUSH 1/4 TUBE 1/8 FNPT800-449C2.
TUBE NYLON 1/4OD X 062WL990-109R3.
GREASE ADAPT 1/4-28M X 1/4 TB800-211C4.
HFSS 1/4-20X1/2 GR5802-148C5.
WASHER FLAT 1/4 SAE PLT804-007C6.
WASHER LOCK SPRING 1/4 PLT804-006C7.
NUT HEX 1/4-20 PLT803-006C8.
GREASE BANK MOUNT197-194D9.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 37 - 160-219P
Page 38
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel
(Applies to NTA3010, NTA3510 only)
15466
160-219P - 38 - 04/10/13
Page 39
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel
(Applies to NTA3010, NTA3510 only)
Image No.dwg15466
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
PRESS WHEEL PIVOT TUBE198-137D3.
PARALLEL ARM PIVOT BUSHING817-084C4.
98 1X12 PRESS WHEEL WELDMENT199-022H5.
HHCS 5/8-11X1 1/2 GR5802-051C6.
WASHER LOCK SPRING 5/8 PLT804-022C7.
1 X 12 PRESS WHL ASSY-5203BRG814-174C8.
HHCS 1/4-20X1 GR5802-005C9.
1 X 12 PRESS WHEEL RIM HALF817-330C10.
TIRE RUBBER 1 X 12814-034C11.
BRG .63ID PRESS WHL ASY822-170C12.
NUT HEX LOCK 1/4-20 FLG803-088C13.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 39 - 160-219P
Page 40
Table of Contents Part Number Index
2" x 13" Single Press Wheel
(Applies to NTA3010, NTA3510 only)
15467
160-219P - 40 - 04/10/13
Page 41
Table of Contents Part Number Index
2" x 13" Single Press Wheel
(Applies to NTA3010, NTA3510 only)
Image No.dwg15467
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
PRESS WHEEL PIVOT TUBE198-137D3.
PARALLEL ARM PIVOT BUSHING817-084C4.
WASHER LOCK SPRING 5/8 PLT804-022C6.
HHCS 5/8-11X2 1/2 GR5802-058C7.
2 X 13 PRESS WHEEL ASSEMBLY814-157C8.
BRG .63ID PRESS WHL ASY822-170C9.
HHFS 1/4-20 X 1 1/2 GR 5802-617C10.
NUT HEX LOCK 1/4-20 FLG803-088C11.
2 X 13 PRESS WHEEL RIM HALF817-296C12.
2 X 13 PRESS WHEEL TIRE814-159C13.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.UNIVERSAL PW ARM MACH 2&3X13199-042D5.
1st rev.RPBY 199-042D199-028D5.
04/10/13 - 41 - 160-219P
Page 42
Table of Contents Part Number Index
3" x 13" Single Press Wheel
(Applies to NTA3010, NTA3510 only)
15468
160-219P - 42 - 04/10/13
Page 43
Table of Contents Part Number Index
3" x 13" Single Press Wheel
(Applies to NTA3010, NTA3510 only)
Image No.dwg15468
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
PRESS WHEEL PIVOT TUBE198-137D3.
PARALLEL ARM PIVOT BUSHING817-084C4.
WASHER LOCK SPRING 5/8 PLT804-022C6.
HHCS 5/8-11X2 1/2 GR5802-058C7.
3 X 13 PRESS WHEEL ASSEMBLY814-158C8.
BRG .63ID PRESS WHL ASY822-170C9.
HHFS 1/4-20 X 2 GR 5802-618C10.
NUT HEX LOCK 1/4-20 FLG803-088C11.
3 X 13 PRESS WHEEL RIM HALF817-297C12.
3 X 13 PRESS WHEEL TIRE814-160C13.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.UNIVERSAL PW ARM MACH 2&3X13199-042D5.
1st rev.RPBY 199-042D199-029D5.
04/10/13 - 43 - 160-219P
Page 44
Table of Contents Part Number Index
3" x 14" Peaked Single Press Wheel
(Applies to NTA3010, NTA3510 only)
15469
160-219P - 44 - 04/10/13
Page 45
Table of Contents Part Number Index
3" x 14" Peaked Single Press Wheel
(Applies to NTA3010, NTA3510 only)
Image No.dwg15469
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
PRESS WHEEL PIVOT TUBE198-137D3.
PARALLEL ARM PIVOT BUSHING817-084C4.
3 X 14 PRESS WHEEL ARM199-030D5.
WASHER LOCK SPRING 5/8 PLT804-022C6.
HHCS 5/8-11X3 GR5802-059C7.
3 X 14 PEAKED P.W. ASSEMBLY122-117S8.
HHCS 5/16-18X2 3/4 GR5802-197C9.
BRG INS .63IDX1.57OD DBL LIP822-095C10.
803-184 FLG TP LK 5/16-18ZNYCR803-177C11.
4X12 PW RIM HALF122-041D12.
3 X 14 RIM SPACER RING817-063C13.
3 X 14 PEAKED PRESS WHEEL TIRE814-067C14.
3 X 14 TIRE & RING ASSEMBLY122-198V15.
LARGE SPACER TUBE817-062C16.
SMALL SPACER TUBE122-110D17.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 45 - 160-219P
Page 46
Table of Contents Part Number Index
Folding Hydraulics
(Applies to NTA3010, NTA3510 only)
16364
160-219P - 46 - 04/10/13
Page 47
Table of Contents Part Number Index
Folding Hydraulics
(Applies to NTA3010, NTA3510 only)
Image No.dwg16364
RPBY 196-430D811-172C1.
EL 3/4MJIC 3/4MORB811-063C2.
HH3/8R2 108 3/4FJIC 3/4FJIC811-687C3.
TE 3/4MJIC 3/4MORB 3/4MJIC811-080C4.
EL 3/4FJIC 3/4MJIC811-150C5.
NC POPPET SOLENOID VALVE810-342C6.
HH3/8R2 012 3/4FJIC 3/4FJIC811-686C7.
HH3/8R2 019 3/4FJIC 3/4FJIC811-688C8.
HH3/8R2 048 3/4FJIC 3/4FJIC811-685C9.
CYL 4.5X41.75X2 ROD810-332C10.
HH3/8R2 099 3/4FJIC811-671C11.
RPBY 196-146D196-112D12.
HOSE CLIP 13/16 ID800-064C13.
WASHER LOCK SPRING 5/16 PLT804-009C14.
HHCS 5/16-18X1 1/4 GR5802-010C15.
HH3/8R2 080 3/4MORB 3/4FJIC RF811-683C16.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Solenoid Valve (810-342C)"
for breakdown
Refer to "Hydraulic Cylinder
(810-332C)" for breakdown
04/10/13 - 47 - 160-219P
Page 48
Table of Contents Part Number Index
Depth Stop Valve Assembly
(Applies to NTA3010, NTA3510 only)
16367
160-219P - 48 - 04/10/13
Page 49
Table of Contents Part Number Index
Depth Stop Valve Assembly
(Applies to NTA3010, NTA3510 only)
Image No.dwg16367
SCREW ADJUSTMENT ROD122-055S1.
TENSION SPRING RETAINER122-065D2.
DEPTH ADJUSTMENT BRACKET WLMT152-179H3.
1/4 SPACER TUBE152-379D4.
7/16 SPACER TUBE152-380D5.
2SNT DEPTH VALVE MNT WELDMENT196-185H6.
RHSNB 1/4-20X3/4 GR5802-002C7.
HHCS 1/4-20X3 GR5802-274C8.
NUT-HEX 1/4-20 PLT803-006C9.
HUT HEX NYLOCK 7/16-14 PLT803-273C10.
WASHER LOCK SPRING 1/4 PLT804-006C11.
WASHER FLAT 7/16 SAE PLT804-041C12.
SPRING SCREW ADJ TENSION STRHT807-020C13.
STROKE CONTROL VALVE810-445C14.
RPBY 810-445C810-084C14.
EL 3/4MJIC 3/4MORB811-063C15.
KNOB P.W. ADJUSTMENT817-021C16.
HHCS 3/4-10X6 GR5802-070C17.
SPRING LEVER807-007C18.
2SNT DPTH VAL CLEVIS PLT WLMT196-186H19.
NUT HEX 3/4-10 PLT NYLOCK803-025C20.
HHCS 3/8-16X3 3/4 GR5802-026C21.
WASHER LOCK SPRING 3/8 PLT804-013C22.
NUT HEX 3/8-16 PLT803-014C23.
HHCS 3/8-16X5 1/2 GR5802-616C24.
AD 3/4MORB 3/4MJIC811-088C25.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.Refer to "Hydraulic Shut-Off Valve
(810-084C)"
1st rev.Refer to "Stroke Control Valve
(810-445C)"
04/10/13 - 49 - 160-219P
Page 50
Table of Contents Part Number Index
Hydraulic Cylinder (810-221C)
(Applies to NTA3010, NTA3510 only)
14712
160-219P - 50 - 04/10/13
Page 51
Table of Contents Part Number Index
Hydraulic Cylinder (810-221C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg14712
ROD MIDWAY2M75202.
HEAD MIDWAY3R69123.
RPBY 4R61084R61064.
TUBE MIDWAY5R61205.
MW BASE6R61646.
TIE ROD MIDWAY7M73207.
MW PISTON NUT 1-142A002416.
RPBY 803-257C2A001917.
RPBY 803-234C2A001218.
RPBY 802-023C2A000619.
SEAL KIT MW 4.25 RPHCYL 4A6104810-144C20.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Only available in item 20.WIPER SEAL8.
Only available in item 20.O-RING9.
Only available in item 20.BACK-UP10.
Only available in item 20.O-RING11.
Only available in item 20.BACK-UP12.
Only available in item 20.TEFLON SEAL13.
Only available in item 20.LOADER O-RING14.
Only available in item 20.WEAR RING15.
04/10/13 - 51 - 160-219P
Page 52
Table of Contents Part Number Index
Hydraulic Cylinder (810-287C)
(Applies to NTA3010, NTA3510 only)
15166
160-219P - 52 - 04/10/13
Page 53
Table of Contents Part Number Index
Hydraulic Cylinder (810-287C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg15166
RPBY 1M7016-ADI1M70181.
MW ROD2M85182.
MIDWAY HEAD F/ 4 3/4 CYL3R85123.
PISTON MIDWAY4R81064.
MIDWAY TUBE5R81205.
MW BASE6R81646.
MW PISTON NUT 1 1/4'"-12 UNF2A002516.
RPBY 803-257C2A001917.
RPBY 803-234C2A001218.
RPBY 802-023C2A000619.
SEAL KIT MW 4.75 RPHCYL 4A8104810-160C20.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Only available in item 20.ROD WIPER8.
Only available in item 20.BACK-UP10.
Only available in item 20.O-RING11.
Only available in item 20.TEFLON SEAL13.
Only available in item 20.LOADER O-RING14.
Only available in item 20.WEAR RING15.
04/10/13 - 53 - 160-219P
Page 54
Table of Contents Part Number Index
Hydraulic Cylinder (810-332C)
(Applies to NTA3010, NTA3510 only)
16394
160-219P - 54 - 04/10/13
Page 55
Table of Contents Part Number Index
Hydraulic Cylinder (810-332C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16394
RPBY 803-257C2A00191.
MW BASE6R71702.
TIE ROD MIDWAY7M73985.
MW TUBE5M75956.
MW PISTON NUT 1-142A00247.
MW PISTON4M71088.
MW HEAD 4.5 X 16 X 23R761211.
MW ROD2M769014.
RPBY 802-023C2A000615.
RPBY 803-234C2A001216.
MIDWAY ROD CLEVIS1M702017.
SEAL KIT MW 4.5 CYL 5A7116810-236C18.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Only available in item 18.BACK-UP MIDWAY3.
Only available in item 18.O-RING4.
Only available in item 18.MW BACK-UP9.
Only available in item 18.MW O-RING10.
Only available in item 18.U-CUP12.
Only available in item 18.MW WIPER13.
04/10/13 - 55 - 160-219P
Page 56
Table of Contents Part Number Index
Hydraulic Cylinder (810-333C)
(Applies to NTA3010, NTA3510 only)
16395
160-219P - 56 - 04/10/13
Page 57
Table of Contents Part Number Index
Hydraulic Cylinder (810-333C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16395
RPBY 1M7016-ADI1M70181.
MW ROD2M75182.
HEAD MIDWAY3R75123.
RPBY 4R71084R71064.
TUBE MIDWAY5R71205.
MW BASE6R71776.
TIE ROD MIDWAY7M73207.
WEAR RING MIDWAY2A032714.
MW PISTON NUT 1-142A002415.
RPBY 803-257C2A001916.
RPBY 803-234C2A001217.
RPBY 802-023C2A000618.
SEAL KIT MW 4.5 RPHCYL 4A7104810-158C19.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Only available in item 19.MW WIPER8.
Only available in item 19.U-CUP9.
Only available in item 19.O-RING10.
Only available in item 19.BACK-UP MIDWAY11.
Only available in item 19.SEAL, TEFLON MIDWAY12.
Only available in item 19.O-RING LOADER MIDWAY13.
04/10/13 - 57 - 160-219P
Page 58
Table of Contents Part Number Index
Hydraulic Shut-Off Valve (810-084C)
(Applies to NTA3010, NTA3510 only)
16327
160-219P - 58 - 04/10/13
Page 59
Table of Contents Part Number Index
Hydraulic Shut-Off Valve (810-084C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16327
SEAL KIT MONARCH STROKE CONTRL810-335C1.
MONARCH ROD CAP4946652.
MONARCH STROKE CONTROL VALVE4925443.
RPBY 810-445C810-084C
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 59 - 160-219P
Page 60
Table of Contents Part Number Index
NTA Control Valve (S/N Z1101+)
(Applies to NTA3010, NTA3510 only)
17216
160-219P - 60 - 04/10/13
Page 61
Table of Contents Part Number Index
NTA Control Valve (S/N Z1101+)
(Applies to NTA3010, NTA3510 only)
Image No.dwg17216
NUT HEX 3/8-16 PLT803-014C1.
WASHER LOCK SPRING 3/8 PLT804-013C2.
U-BOLT 3/8-16 X 4 1/32 X 2 3/4806-111C3.
NTA VALVE ASSY IMPLEMENT MNT160-613D4.
NUT-HEX 1/4-20 PLT803-006C5.
WASHER LOCK SPRING 1/4 PLT804-006C6.
WASHER FLAT 1/4 SAE PLT804-007C7.
HH3/8R2 148 3/4MORB 9/16FJIC811-681C9.
AD 9/16MORB 9/16MJIC811-170C10.
EL 9/16MJIC 9/16MORB811-065C11.
AD 9/16FJIC 1/4FNPT811-582C12.
PRESSURE GAUGE 2000 PSI810-347C13.
HHCS 1/4-20X2 1/4 GR5802-551C14.
EL 3/4MORB 9/16MJIC811-171C15.
EL 3/4MJIC 9/16MORB811-216C16.
AD 3/4MORB 3/4FJIC811-324C17.
VALVE 90 DEGREE SHUT-OFF810-345C18.
AD 9/16MORB 9/16FJIC811-627C19.
RELIEF VALVE 1500 PSI TAMP PRF810-348C20.
HH3/8R2 017 9/16FJIC811-702C21.
TE 9/16MJIC 9/16MJIC 9/16MORB811-064C22.
HH3/8R2 099 3/4FJIC811-671C23.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Relief Valve (810-370C)"VALVE PRESS RED W/ CHK 1/16 OR810-349C8.
Refer to "Hydraulic Shut-Off Valve
(810-084C)"
04/10/13 - 61 - 160-219P
Page 62
Table of Contents Part Number Index
Pressure Reducing Valve (810-349C)
(Applies to NTA3010, NTA3510 only)
16442
160-219P - 62 - 04/10/13
Page 63
Table of Contents Part Number Index
Pressure Reducing Valve (810-349C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16442
VALVE BODY PRV W/CHECK SHOEMKR50891.
SHOEMAKER ORIFACE51062.
REPLACED BY CP2-10-0CP2-103.
RPBY 507550704.
RPBY 810-452C50755.
CARTRIDGE PRESS RED SHOEMAKERPRPIL-10-K-256.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 63 - 160-219P
Page 64
Table of Contents Part Number Index
Relief & Solenoid Valves
(Applies to NTA3010, NTA3510 only)
16368
160-219P - 64 - 04/10/13
Page 65
Table of Contents Part Number Index
Relief & Solenoid Valves
(Applies to NTA3010, NTA3510 only)
Image No.dwg16368
WASHER FLAT 5/16 SAE PLT804-036C2.
WASHER FLAT 1/4 SAE PLT804-007C3.
NUT-HEX 1/4-20 PLT803-006C4.
NTA SOLENOID VALVE MOUNT160-463D5.
WASHER LOCK SPRING 1/4 PLT804-006C7.
HHCS 5/16-18X2 1/2 GR5802-172C8.
WASHER FLAT 1/4 SAE PLT804-007C9.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Relief Valve (810-370C)"RELIEF VALVE TAMP PROOF1300PSI810-370C1.
Refer to "Solenoid Valve (810-342C)"NC POPPET SOLENOID VALVE810-342C6.
04/10/13 - 65 - 160-219P
Page 66
Table of Contents Part Number Index
Relief Valve (810-348C)
(Applies to NTA3010, NTA3510 only)
16441
160-219P - 66 - 04/10/13
Page 67
Table of Contents Part Number Index
Relief Valve (810-348C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16441
SHOEMAKER BODY FOR 810-348C53811.
SHOEMAKER CARTRIDGERDIF10F18/13.52.
SEAL KIT SHOEMAKER #5075810-452C3.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 67 - 160-219P
Page 68
Table of Contents Part Number Index
Relief Valve (810-370C)
(Applies to NTA3010, NTA3510 only)
14738
160-219P - 68 - 04/10/13
Page 69
Table of Contents Part Number Index
Relief Valve (810-370C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg14738
RELIEF VALVE BODY-SHOEMAKER51491.
SHOEMAKER O-RING1088-0152.
SHOEMAKER BACK-UP BOTTOM1369-0153.
SHOEMAKER O-RING1088-0174.
SHOEMAKER BACK-UP10369-0175.
CARTRIDGE SHOEMAKER RLF 1300RPILS-10-S25/136.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.CARTRIDGE SHOEMAKER RLF 1300RDIF-1O-F18/136.
1st rev.Check "Transport Hydraulics (RDIF
Cartridge)" for new hose routing on
new RDIF Cartridge
04/10/13 - 69 - 160-219P
Page 70
Table of Contents Part Number Index
Solenoid Valve (810-342C)
(Applies to NTA3010, NTA3510 only)
16397
160-219P - 70 - 04/10/13
Page 71
Table of Contents Part Number Index
Solenoid Valve (810-342C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16397
NUT HEX JAM 1/2-20 PLT803-059C1.
DELTA COIL 12VDC W CONN396800082.
DELTA CARTRIDGE VALVE850027333.
DELTA SERIES ES VAVLE BODY301023594.
SEAL KIT 7/8-14 DELTA W/ LTITE500-090B5.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 71 - 160-219P
Page 72
Table of Contents Part Number Index
Stroke Control Valve (810-445C)
(Applies to NTA3010, NTA3510 only)
19650
160-219P - 72 - 04/10/13
Page 73
Table of Contents Part Number Index
Stroke Control Valve (810-445C)
(Applies to NTA3010, NTA3510 only)
Image No.dwg19650
BODY53961.
SHOEMAKER PISTON53972.
PLUG, ADAPTER, ASM.80623.
SEAL KIT 5398 810-445C810-446C4.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 73 - 160-219P
Page 74
Table of Contents Part Number Index
Transport Hydraulics (RDIF Cartridge)
(Applies to NTA3010, NTA3510 only)
19928
160-219P - 74 - 04/10/13
Page 75
Table of Contents Part Number Index
Transport Hydraulics (RDIF Cartridge)
(Applies to NTA3010, NTA3510 only)
Image No.dwg19928
HH1/2R2 80 3/4MORB LIFT811-658C1.
STROKE CONTROL VALVE810-445C3.
RPBY 810-445C810-084C3.
HH3/8R2 214 3/4FJIC811-659C4.
HH1/2R2 220 3/4FJIC811-660C5.
HH3/8R2 168 3/4FJIC811-661C6.
EL 3/4MJIC 3/4MORB811-063C7.
HH3/8R2 268 3/4FJIC811-662C8.
CYL REP 4.75 X 12 X 1.50 ROD810-287C9.
CYL REP 4.5X12X1.5 ROD 22.25L810-333C10.
CYL REP 4.25X12X1.5 ROD (TIE)810-221C11.
HH3/8R2 225 3/4FJIC811-663C12.
AD 3/4MORB 3/4MJIC811-088C13.
TE 3/4MJIC 3/4MORB 3/4MJIC811-080C14.
TE 3/4MORB 3/4MJIC 3/4MJIC811-077C15.
HH3/8R2 38 3/4FJIC811-664C16.
HH1/2R2 208 3/4FJIC811-665C17.
EL 3/4FJIC 3/4MJIC811-150C18.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Relief Valve (810-370C)"RELIEF VALVE TAMP PROOF1300PSI810-370C2.
2nd rev.Refer to "Hydraulic Shut-Off Valve
(810-084C)"
1st rev.Refer to "Hydraulic Shut-Off Valve
(810-084C)"
Refer to "Hydraulic Cylinder
(810-287C)"
Refer to "Hydraulic Cylinder
(810-333C)"
Refer to "Hydraulic Cylinder
(810-221C)"
04/10/13 - 75 - 160-219P
Page 76
Table of Contents Part Number Index
Transport Hydraulics (RPIL Cartridge)
(Applies to NTA3010, NTA3510 only)
16363
160-219P - 76 - 04/10/13
Page 77
Table of Contents Part Number Index
Transport Hydraulics (RPIL Cartridge)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16363
HH1/2R2 80 3/4MORB LIFT811-658C1.
STROKE CONTROL VALVE810-445C3.
RPBY 810-445C810-084C3.
HH3/8R2 214 3/4FJIC811-659C4.
HH1/2R2 220 3/4FJIC811-660C5.
HH3/8R2 168 3/4FJIC811-661C6.
EL 3/4MJIC 3/4MORB811-063C7.
HH3/8R2 268 3/4FJIC811-662C8.
CYL REP 4.75 X 12 X 1.50 ROD810-287C9.
CYL REP 4.5X12X1.5 ROD 22.25L810-333C10.
CYL REP 4.25X12X1.5 ROD (TIE)810-221C11.
HH3/8R2 225 3/4FJIC811-663C12.
AD 3/4MORB 3/4MJIC811-088C13.
TE 3/4MJIC 3/4MORB 3/4MJIC811-080C14.
TE 3/4MORB 3/4MJIC 3/4MJIC811-077C15.
HH3/8R2 38 3/4FJIC811-664C16.
HH1/2R2 208 3/4FJIC811-665C17.
EL 3/4FJIC 3/4MJIC811-150C18.
Hydraulics
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Relief Valve (810-370C)"RELIEF VALVE TAMP PROOF1300PSI810-370C2.
2nd rev.Refer to "Hydraulic Shut-Off Valve
(810-084C)"
1st rev.Refer to "Hydraulic Shut-Off Valve
(810-084C)"
Refer to "Hydraulic Cylinder
(810-287C)"
Refer to "Hydraulic Cylinder
(810-333C)"
Refer to "Hydraulic Cylinder
(810-221C)"
04/10/13 - 77 - 160-219P
Page 78
Table of Contents Part Number Index
Blockage Monitor (Option)
(Applies to NTA3010, NTA3510 only)
16480
160-219P - 78 - 04/10/13
Page 79
Table of Contents Part Number Index
Blockage Monitor (Option)
(Applies to NTA3010, NTA3510 only)
Image No.dwg16480
FRHSNB 1/4-20X4 3/4 GR5802-389C2.
BLOCKAGE MODULE MOUNTING BKT168-365D3.
WASHER LOCK SPRING 1/4 PLT804-006C4.
NUT-HEX 1/4-20 PLT803-006C5.
CABLE TIE .19X7.25 1.75D 50LB800-112C6.
MANUAL BLOCK MONITOR INSTALL168-258M7.
CABLE TIE .31X21.5 6DIA 120LB800-082C8.
MAIN HARNESS LEADVA-4907049.
WIRE 3 COND. 16GA RUBBER COVER990-184R10.
TERM FEMALE INSUL PUSH ON .250833-107C11.
MULTIPLEX BLOCK MODULE LOWRATEVA-15000412.
BLOCKAGE PIN SENSOR - 4 FTVA-141000-0413.
NTA3510-4010 BLKG MONITOR PKG168-257A
NTA3510-5575 BLKG MONITOR PKG168-256A
NTA3010 48R BLKG MONITOR PKG168-260A
NTA3010 36R BLKG MONITOR PKG168-261A
Monitor
RevisionCommentsPart DescriptionPart No.Ref.
NTA3510-7 1/2" spacingVANSCO BLOCK PKG NTA55ROWS 7.5823-158C1.
NTA3510-10" spacingVANSCOBLOCK PKG NTA40ROWS 10823-159C1.
NTA3010-7 1/2" spacingVANSCO BLOCK PKG NTA3010 48R823-161C1.
NTA3010-10" spacingVANSCOBLOCK PKG NTA3010 36R823-162C1.
04/10/13 - 79 - 160-219P
Page 80
Table of Contents Part Number Index
Agtron Sensor (Option) (S/N Z1263-)
(Applies to NTA3010, NTA3510 only)
23262
160-219P - 80 - 04/10/13
Page 81
Table of Contents Part Number Index
Agtron Sensor (Option) (S/N Z1263-)
(Applies to NTA3010, NTA3510 only)
Image No.dwg23262
AGTRON AR99 SEED FLOW SENSOR823-201C1.
NTA3010-4875 AGTRON BLOCK PKG168-352A
NTA3010-3610 AGTRON BLOCK PKG168-353A
NTA3510-5575 AGTRON BLOCK PKG168-354A
NTA3510-4010 AGTRON BLOCK PKG168-355A
Monitor
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 81 - 160-219P
Page 82
Table of Contents Part Number Index
Agtron AGS25 Blockage Sensor (Option) (S/N Z1264+)
(Applies to NTA3010, NTA3510 only)
25104
160-219P - 82 - 04/10/13
Page 83
Table of Contents Part Number Index
Agtron AGS25 Blockage Sensor (Option) (S/N Z1264+)
(Applies to NTA3010, NTA3510 only)
Image No.dwg25104
CLAMP WRM DRV #20SS (.81-1.75)800-257C1.
AGTRON AGSS25 BLOCKAGE SENSOR823-246C2.
NTA3010-4875 AGTRON BLOCK PKG168-352A
NTA3010-3610 AGTRON BLOCK PKG168-353A
NTA3510-5575 AGTRON BLOCK PKG168-354A
NTA3510-4010 AGTRON BLOCK PKG168-355A
Monitor
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 83 - 160-219P
Page 84
Table of Contents Part Number Index
Implement Kit
(Applies to NTA3010, NTA3510 only)
26391
160-219P - 84 - 04/10/13
Page 85
Table of Contents Part Number Index
Implement Kit
(Applies to NTA3010, NTA3510 only)
Image No.dwg26391
10' EXT HARNESS4679801411.
3' REAR HITCH HARNESS4679803602.
DJ 6' HITCH EXTENSION4679801343.
DJ 2SOL YP24LIFT/HITCH FCM HRN4679835024.
PLNTR CNTRL OUTPUT MODULE(POM)467982000S15.
NTA SOL INTERFACE EXT CABLE4679804766.
DJ SE SEED MAN 2-PIN CABLE PLG4642113307.
Monitor
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 85 - 160-219P
Page 86
Table of Contents Part Number Index
Monitor NTA3010
(Applies to NTA3010, NTA3510 only)
26393
160-219P - 86 - 04/10/13
Page 87
Table of Contents Part Number Index
Monitor NTA3010
(Applies to NTA3010, NTA3510 only)
Image No.dwg26393
DJ 20' HARNESS EXT ISO SYS CAN4679801401.
INT AG HARNESS, WSMB MODULE4679812012.
INTAG WSMB/FLW MNTR MODULE 18R467981100S13.
10' EXT HARNESS4679801414.
12 ROW HARNESS4677513205.
5' EXT HARNESS4679801426.
DUST PLUG4642110907.
Monitor
RevisionCommentsPart DescriptionPart No.Ref.
Rev. 1RECON II467420352S18.
Rev. 2VIGILENSE BLOCKAGE SENSOR 25MM4674207018.
04/10/13 - 87 - 160-219P
Page 88
Table of Contents Part Number Index
Monitor NTA3510
(Applies to NTA3010, NTA3510 only)
26392
160-219P - 88 - 04/10/13
Page 89
Table of Contents Part Number Index
Monitor NTA3510
(Applies to NTA3010, NTA3510 only)
Image No.dwg26392
DJ 20' HARNESS EXT ISO SYS CAN4679801401.
INT AG HARNESS, WSMB MODULE4679812012.
INTAG WSMB/FLW MNTR MODULE 18R467981100S13.
10' EXT HARNESS4679801414.
12 ROW HARNESS4677513205.
DUST PLUG4642110906.
Monitor
RevisionCommentsPart DescriptionPart No.Ref.
Rev. 1RECON II467420352S17.
Rev. 2VIGILENSE BLOCKAGE SENSOR 25MM4674207017.
04/10/13 - 89 - 160-219P
Page 90
Table of Contents Part Number Index
Tower for ADC2220 Air Cart Drill
(Applies to NTA3010, NTA3510 only)
16282
160-219P - 90 - 04/10/13
Page 91
Table of Contents Part Number Index
Tower for ADC2220 Air Cart Drill
(Applies to NTA3010, NTA3510 only)
Image No.dwg16282
U-BOLT 1/2-13 X 4 1/32 X 5 1/4806-056C1.
U-BOLT 1/2-13 X 4 1/32 X 7 1/4806-069C1.
SEED HOSE 2 1/2 ID KANAFLEX990-125R2.
2 1/2 AIR HOSE BAND CLAMP800-180C3.
U-BOLT 1/2-13 X 2 1/2 X 3 1/2806-010C4.
DESTRIBUTION TOWER WELDMENT168-216H5.
WASHER LOCK SPRING 1/2 PLT804-015C6.
NUT HEX 1/2-13 PLT803-020C7.
NUT HEX NYLOCK 5/16-18 PLT803-084C8.
WASHER FLAT 5/16 USS PLT804-010C9.
PVC SEED HOSE 1 IN/FT817-039C10.
11 OUTLET SEED DIST. RING816-218C11.
8 OUTLET SEED DIST. RING816-216C11.
9 OUTLET SEED DIST. RING816-217C11.
212 OUTLETSEED DIST. RING816-288C11.
DIST TOWER DIVIDER817-234C12.
RPBY 168-314D834-014C13.
HHCS 5/16-18X3/4 GR5802-007C14.
HHCS 5/16-18X3 GR5802-131C15.
NTA35 DIST TOWER MOUNT168-362D16.
Towers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 91 - 160-219P
Page 92
Table of Contents Part Number Index
Tower for ADC2350 Air Cart Drill
(Applies to NTA3010, NTA3510 only)
26421
160-219P - 92 - 04/10/13
Page 93
Table of Contents Part Number Index
Tower for ADC2350 Air Cart Drill
(Applies to NTA3010, NTA3510 only)
Image No.dwg16282
U-BOLT 1/2-13 X 4 1/32 X 5 1/4806-056C1.
U-BOLT 1/2-13 X 4 1/32 X 7 1/4806-069C1.
SEED HOSE 2 1/2 ID KANAFLEX990-125R2.
2 1/2 AIR HOSE BAND CLAMP800-180C3.
U-BOLT 1/2-13 X 2 1/2 X 3 1/2806-010C4.
DESTRIBUTION TOWER WELDMENT168-216H5.
WASHER LOCK SPRING 1/2 PLT804-015C6.
NUT HEX 1/2-13 PLT803-020C7.
NUT HEX NYLOCK 5/16-18 PLT803-084C8.
WASHER FLAT 5/16 USS PLT804-010C9.
PVC SEED HOSE 1 IN/FT817-039C10.
16 OUTLET SEED DIST. RING816-290C11.
13 OUTLET SEED DIST. RING816-289C11.
10 OUTLET SEED DIST. RING816-287C11.
DIST TOWER DIVIDER817-234C12.
RPBY 168-314D834-014C13.
HHCS 5/16-18X3/4 GR5802-007C14.
HHCS 5/16-18X3 GR5802-131C15.
NTA35 DIST TOWER MOUNT168-362D16.
HFSS 3/8-16X3/4 LG802-185C17.
HHCS 1/4-20X1 1/4 GR5802-224C18.
NUT-HEX 1/4-20 PLT803-006C19.
WASHER LOCK SPRING 1/4 PLT804-006C20.
INTAG WSMB/FLW MNTR MODULE 18R467981100S121.
Towers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 93 - 160-219P
Page 94
Table of Contents Part Number Index
Decal Placement
(Applies to NTA3010, NTA3510 only)
16371
160-219P - 94 - 04/10/13
Page 95
Table of Contents Part Number Index
Decal Placement
(Applies to NTA3010, NTA3510 only)
Image No.dwg16371
DECAL LIFT CYL OPERATING INSTR818-043C1.
DECAL CAUTION TIRES NOT A STEP818-398C4.
DECAL WARNING PINCH POINT GEN818-798C5.
DECAL DANGER CHARGE FOLD CYL818-046C6.
DECAL DANGER CRUSH AD/IMPLEM818-624C7.
DECAL NOTICE TO OWNER-NO WARRA818-560C8.
DECAL DANGER CANNOT READ ENG818-557C9.
DECAL DANGER ELECTROCUTION AUG818-627C10.
DECAL NOTICE FOLD IMP/CYL LOCK818-631C11.
DECAL GREAT PLAINS W/LOGO818-412C12.
DECAL WARNING HIGH PRESSUR SML818-339C13.
DECAL SLOW MOVING-GALV. BACKED818-055C14.
DECAL LOGO&GP F/STRIPE 4 X 24838-161C15.
DECAL SUMP818-882C19.
DECAL SEL VALVE FOLD/FIELD818-795C20.
DECAL NOTICE FOLD IMP/CYL LOCK818-631C21.
Decals
RevisionCommentsPart DescriptionPart No.Ref.
2000-DECAL RED REFLECTOR818-230C2.
2001-DECAL AMBER REFLECTOR818-229C3.
Refer to "Slow Moving Vehicle
Emblem" for mounting hardware.
2nd rev.DECAL 3 COLOR STRIPE 2.50 WIDE838-160C16.
1st rev.DECAL 4 COLOR STRIPE - 2 3/8818-800C16.
2nd rev.DECAL NTA3510838-223C17.
1st rev.DECAL NTA3510818-813C17.
2nd rev.DECAL NTA3010838-222C17.
1st rev.DECAL NTA3010818-853C17.
This decal is located on each tire.DECAL CAUTION TIRE 52 PSI818-752C18.
2001+DECAL REFLECTOR AMBER 1 1/2X9838-265C22.
2001+DECAL REFLECTOR RED 1 1/2X9838-266C23.
2001+DECAL REFLECTR DAYTIME 1 1/2X9838-267C24.
04/10/13 - 95 - 160-219P
Page 96
Table of Contents Part Number Index
Coulter Tine
(Applies to NTA3010, NTA3510 only)
15683
160-219P - 96 - 04/10/13
Page 97
Table of Contents Part Number Index
Coulter Tine
(Applies to NTA3010, NTA3510 only)
Image No.dwg15683
HHCS 7/8-9X3 1/2 GR5802-126C1.
COULTER TINE MOUNT149-550D2.
HHCS 5/8-11X4 1/2 GR5802-100C3.
HHCS 3/8-16X1 1/2 GR5802-022C4.
WASHER FLAT 3/8 USS PLT804-011C5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
NUT HEX 3/8-16 PLT803-014C7.
COULTER TINE CLAMP PLATE149-549D8.
2SNT COULTER TINE820-114C9.
WASHER LOCK SPRING 7/8 PLT804-037C10.
NUT HEX 7/8-9 PLT803-049C11.
Options
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 97 - 160-219P
Page 98
Table of Contents Part Number Index
Harrow Assembly
(Applies to NTA3010, NTA3510 only)
16951
160-219P - 98 - 04/10/13
Page 99
Table of Contents Part Number Index
Harrow Assembly
(Applies to NTA3010, NTA3510 only)
Image No.dwg16951
HHCS 5/16-18X2 1/4 GR5802-138C1.
WASHER FLAT 5/16 USS PLT804-010C2.
SHEAR BUSHING 5/8X.357113-271D3.
NUT HEX NYLOCK 5/16-18 PLT803-084C4.
SPRING HARROW DBL TORSION 11807-079C5.
CENTER BRACE WELDMENT116-062H8.
NUT HEX 1/2-13 PLT803-020C9.
WASHER LOCK SPRING 1/2 PLT804-015C10.
U-BOLT 1/2-13 X 1 3/8X2 3/4 LG806-046C11.
Options
RevisionCommentsPart DescriptionPart No.Ref.
All except NTA3010 wings.20' FRAME WELDMENT116-064H6.
For NTA3010 wings.NTA HARROW WING FRAME - 30'116-179H6.
For NTA3010 wings.14' TINE TUBE116-116D7.
For NTA3510 wings.NTA HARROW TINE TUBE-35' WING116-205D7.
For all centers.NTA HARROW TINE TUBE - CTR116-208D7.
04/10/13 - 99 - 160-219P
Page 100
Table of Contents Part Number Index
Harrow Center Mount
(Applies to NTA3010, NTA3510 only)
16949
160-219P - 100 - 04/10/13
Loading...