Great Plains 3N-4025P User Manual

Table of Contents Part Number Index

Parts Manual

3N-4010P, 3N-4010HDP, 3N-4015P, 3N-4020P &

Precision Seeding System

3N-4025P

Read the Operator's manual entirely.When you see this symbol, the subsequent
instructions and warnings are serious - follow without exception.Your life and the
lives of others depend on it!

20293

Cover illustration may show optional equipment not supplied with standard unit.

© Copyright 2013 Printed 04/10/13 196-286P

Table of Contents Part Number Index

Table of Contents

Section 1: Introduction.................................................6

Using This Manual...............................................................6

Manual Replacement Information.......................................6

Manual Revisions................................................................6

Touch-up Paint....................................................................6

Hardware Legend................................................................7

Replacement Hardware......................................................7

Serial Numbers...................................................................7

Part Number Service Coding..............................................7

Tongue and Frame.........................................................8

Hitch To Tongue...................................................................8

Tongue To Wings...............................................................10

Wing To Center Frame......................................................12

Rockshaft.....................................................................15

Rockshaft..........................................................................16

Rockshaft To Frame..........................................................18

Rear Axle Assembly..........................................................20

Gauge Wheel....................................................................24

Gauge Wheel Locking Plate..............................................28

Box To Frame...............................................................30

Box To Frame....................................................................30

Box Components...............................................................32

Seed Level Indicator..........................................................34

Walkboards And Steps......................................................36

Drive.............................................................................38

10 & 20 Series Center Section Drive................................38

HD10 & 25 Series Center Section Drive...........................40

Wing Drive.........................................................................42

Veris Drive Components...................................................44

Veris Drive Controller........................................................46

Meter.............................................................................48

10 & 20 Series Singulating Meter......................................48

HD10 & 25 Series Singulating Meter................................52

25 Series Corn Meter........................................................56

12FP Corn Meter (890-856C)...........................................58

6FP Corn Meter (890-857C).............................................60

Seed Tray With Telescoping Tubes....................................62

Openers........................................................................64

10 Series Opener Arms & Mounts....................................64

10 Series Opener Body.....................................................66

15 Series Opener Arms & Mounts....................................68

15 Series Opener Body.....................................................70

15 Series Side Gauge Wheel............................................72

15 Series Meter To Row Unit.............................................74

20 Series Opener Arms & Mounts....................................76

20 Series Opener Body.....................................................78

HD10 Series Opener Arms & Mounts...............................80

HD10 Series Opener Body................................................84

25 Series Opener Arms & Mounts....................................86

© Copyright 2013 All rights reserved Printed 04/10/13

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from
the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes
the state of this product at the time of its publication, and may not reflect the product in the future.

The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains

All other brands and product names are trademarks or registered trademarks of their respective holders.

Great Plains Manufacturing, Incorporated Trademarks

Printed in the United States of America.

25 Series Opener Body.....................................................90

Side Depth Wheel Assembly.............................................94

10 & 20 Series Keeton Seed Firmer (Option)...................96

25 Series Keeton Seed Firmer (Option)............................98

Air Design Scraper (Option)............................................100

20 Series Side Wheel Scraper (Option)..........................102

25 Series Side Depth Wheel Scraper Assembly.............104

10 & 20 Series 5" & 6" Seed-Lok (Option)......................106

15, HD10 & 25 Series Seed Lok (Option).......................108

Coulter.............................................................................110

Conservation Coulter (Option)........................................112

Grease Bank...................................................................114

Coulter Tine (Option).......................................................116

Press Wheels.............................................................118

2" x 13" Single Press Wheel............................................118

3" x 13" Single Press Wheel............................................120

1" x 12" Double "V" Press Wheel (10 Series)..................122

1" x 12" Double "V" Press Wheel 20 Series)...................124

1" x 12" Double "V" Press Wheel Short...........................126

1" x 12" Double "V" Press Wheel Long...........................128

1" x 10" Double "V" Press Wheel....................................130

1 1/4" x 13 1/2" Double Press Wheel..............................132

1 1/4" x 13" Double Press Wheel....................................134

2" x 12 1/2" Double Press Wheel (10 Series)..................136

2" x 12 1/2" Double Press Wheel (20 Series)..................138

6 1/2" Press Wheel Closing Disk.....................................140

25 Series 16 Degree Press Wheel Assembly (S/N

1053PP-)...................................................................142

25 Series 16 Degree Press Wheel Assembly (S/N

1054PP+)..................................................................144

25 Series 20 Degree Press Wheel Assembly (S/N

1053PP-)...................................................................146

25 Series 20 Degree Press Wheel Assembly (S/N

1054PP+)..................................................................148

25 Series Press Wheel Assembly Breakdowns..............150

25 Series Press Wheel Assembly LH Short (S/N

1053PP-)...................................................................152

25 Series Press Wheel Assembly LH Short (S/N

1054PP+)..................................................................154

25 Series Press Wheel Assembly RH Long (S/N

1053PP-)...................................................................156

25 Series Press Wheel Assembly RH Long (S/N

1054PP+)..................................................................158

Hydraulics..................................................................160

Lift And Fold Hydraulics..................................................160

Rear Axle Hydraulics.......................................................162

Lock Cylinder Hydraulics.................................................164

Hydraulic Cylinder (810-500C 5x20x2 Rod)....................166

Hydraulic Cylinder (810-499C 5x24x2 Rod)....................168

Hydraulic Cylinder (810-498C 4.5x16x1.5 Rod)..............170

196-286P - 2 - 04/10/13

Table of Contents Part Number Index

Table of Contents (continued)

Hydraulic Cylinder (810-497C 4.75x16x1.5 Rod).......172

Hydraulic Cylinder (810-496C 5x16x1.5 Rod)............174

Hydraulic Cylinder (810-201C 1.5x2.5x.75 Rod)........176

Stroke Control Valve (810-503C)................................178

Double Selector Valve (810-274C).............................180

Decals....................................................................182

Decals........................................................................182

Monitor...................................................................184

Monitor 833-291C 7 1/2" Spacing (Option)................184

Monitor 833-292C 10" Spacing (Option)....................186

Monitor 833-293C 15" Spacing & 25 Series Twin Row

(Option)................................................................188

Monitor 833-085C 25 Series Twin Row (Option)........190

Monitor 833-086C 25 Series 15" Spacing (Option).....192

Point Row...................................................................194

Marker....................................................................196

Marker Arm................................................................196

Marker Disk And Hub (113-790S)..............................198

LH Marker Hydraulics.................................................200

Dual Marker Hydraulics..............................................202

Hydraulic Cylinder (810-423C 3 x 24 x 1.5 Rod)........204

Sequence Valve (810-422C)......................................206

Weight Bracket......................................................208

Weight Bracket (Option).............................................208

Baffle (Option).......................................................210

Twin Row Baffle..........................................................210

Part Number Index................................................212

04/10/13 - 3 - 196-286P

Table of Contents Part Number Index

Alphabetized Table of Contents

Selected Models

1

1 1/4" x 13 1/2" Double Press Wheel..............................132

1 1/4" x 13" Double Press Wheel....................................134

1" x 10" Double "V" Press Wheel....................................130

1" x 12" Double "V" Press Wheel (10 Series)..................122

1" x 12" Double "V" Press Wheel 20 Series)...................124

1" x 12" Double "V" Press Wheel Long...........................128

1" x 12" Double "V" Press Wheel Short...........................126

10 & 20 Series 5" & 6" Seed-Lok (Option)......................106

10 & 20 Series Center Section Drive................................38

10 & 20 Series Keeton Seed Firmer (Option)...................96

10 & 20 Series Singulating Meter......................................48

10 Series Opener Arms & Mounts....................................64

10 Series Opener Body.....................................................66

12FP Corn Meter (890-856C)...........................................58

15 Series Meter To Row Unit.............................................74

15 Series Opener Arms & Mounts....................................68

15 Series Opener Body.....................................................70

15 Series Side Gauge Wheel............................................72

15, HD10 & 25 Series Seed Lok (Option).......................108

2

2" x 12 1/2" Double Press Wheel (10 Series)..................136

2" x 12 1/2" Double Press Wheel (20 Series)..................138

2" x 13" Single Press Wheel............................................118

20 Series Opener Arms & Mounts....................................76

20 Series Opener Body.....................................................78

20 Series Side Wheel Scraper (Option)..........................102

25 Series 16 Degree Press Wheel Assembly (S/N

1053PP-)...................................................................142

25 Series 16 Degree Press Wheel Assembly (S/N

1054PP+)..................................................................144

25 Series 20 Degree Press Wheel Assembly (S/N

1053PP-)...................................................................146

25 Series 20 Degree Press Wheel Assembly (S/N

1054PP+)..................................................................148

25 Series Corn Meter........................................................56

25 Series Keeton Seed Firmer (Option)............................98

25 Series Opener Arms & Mounts....................................86

25 Series Opener Body.....................................................90

25 Series Press Wheel Assembly Breakdowns..............150

25 Series Press Wheel Assembly LH Short (S/N

1053PP-)...................................................................152

25 Series Press Wheel Assembly LH Short (S/N

1054PP+)..................................................................154

25 Series Press Wheel Assembly RH Long (S/N

1053PP-)...................................................................156

25 Series Press Wheel Assembly RH Long (S/N

1054PP+)..................................................................158

25 Series Side Depth Wheel Scraper Assembly.............104

3

3" x 13" Single Press Wheel............................................120

6

6 1/2" Press Wheel Closing Disk.....................................140

6FP Corn Meter (890-857C).............................................60

A

Air Design Scraper (Option)............................................100

B

Box Components...............................................................32

Box To Frame....................................................................30

C

Conservation Coulter (Option)........................................112

Coulter.............................................................................110

Coulter Tine (Option).......................................................116

D

Decals.............................................................................182

Double Selector Valve (810-274C)..................................180

Dual Marker Hydraulics...................................................202

G

Gauge Wheel....................................................................24

Gauge Wheel Locking Plate..............................................28

Grease Bank...................................................................114

H

HD10 & 25 Series Center Section Drive...........................40

HD10 & 25 Series Singulating Meter................................52

HD10 Series Opener Arms & Mounts...............................80

HD10 Series Opener Body................................................84

Hitch To Tongue...................................................................8

Hydraulic Cylinder (810-201C 1.5x2.5x.75 Rod).............176

Hydraulic Cylinder (810-423C 3 x 24 x 1.5 Rod).............204

Hydraulic Cylinder (810-496C 5x16x1.5 Rod).................174

Hydraulic Cylinder (810-497C 4.75x16x1.5 Rod)............172

Hydraulic Cylinder (810-498C 4.5x16x1.5 Rod)..............170

Hydraulic Cylinder (810-499C 5x24x2 Rod)....................168

Hydraulic Cylinder (810-500C 5x20x2 Rod)....................166

L

LH Marker Hydraulics......................................................200

Lift And Fold Hydraulics..................................................160

Lock Cylinder Hydraulics.................................................164

M

Marker Arm.....................................................................196

Marker Disk And Hub (113-790S)...................................198

Monitor 833-085C 25 Series Twin Row (Option).............190

Monitor 833-086C 25 Series 15" Spacing (Option).........192

Monitor 833-291C 7 1/2" Spacing (Option).....................184

Monitor 833-292C 10" Spacing (Option).........................186

Monitor 833-293C 15" Spacing & 25 Series Twin Row

(Option).....................................................................188

P

Point Row........................................................................194

196-286P - 4 - 04/10/13

Table of Contents Part Number Index

Alphabetized Table of Contents (continued)

R

Rear Axle Assembly.....................................................20

Rear Axle Hydraulics..................................................162

Rockshaft.....................................................................16

Rockshaft To Frame......................................................18

S

Seed Level Indicator.....................................................34

Seed Tray With Telescoping Tubes...............................62

Sequence Valve (810-422C)......................................206

Side Depth Wheel Assembly........................................94

Stroke Control Valve (810-503C)................................178

T

Tongue To Wings..........................................................10

Twin Row Baffle..........................................................210

V

Veris Drive Components...............................................44

Veris Drive Controller...................................................46

W

Walkboards And Steps.................................................36

Weight Bracket (Option).............................................208

Wing Drive....................................................................42

Wing To Center Frame.................................................12

04/10/13 - 5 - 196-286P

Table of Contents Part Number Index

196-286P - 6 - 04/10/13

Table of Contents Part Number Index

04/10/13 - 7 - 196-286P

Table of Contents Part Number Index

Hitch To Tongue

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20279

196-286P - 8 - 04/10/13

Table of Contents Part Number Index

Hitch To Tongue

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20279

April 05+40P TONGUELH PULLBAR WLDMT196-419H1.
March 05-40P TONGUELH PULLBAR WLDMT196-295H1.
April 05+40P TONGUERH PULLBAR WLDMT196-417H2.
March 05-40P TONGUERH PULLBAR WLDMT196-296H2.

SCREW JACK 5000# 15-30890-246C3.

April 05+HITCH PIVOT MOUNT WLDMT196-420H4.

March 05-HITCH PIVOT MOUNT WLDMT196-345H4.
HHCS 1 1/4-7X9 1/2 GR5 SPTHD802-166C5.
NUT HEX 1 1/4-7 NYLON INSERT803-081C6.
SAFETY CHAIN WASHER194-070D7.
HHCS 1 1/4-7X11 GR5 SPTHD802-317C8.
SAFETY CHAIN 40000 LB890-398C9.
SINGLE HITCH STRAP-LARGE170-033H10.
RPBY 196-136H170-058H11.
WASHER LOCK 1 1/4 SPRING PLT804-030C12.
NUT HEX 1 1/4-7 PLT803-034C13.
SINGLE HITCH STRAP-SMALL170-034H14.
U-BOLT 5/8-11 X 6 1/32 X 7 3/4806-039C15.
TONGUE SPACERSKID BLOCK817-520C16.
SLIDER BLOCK ADJUST SHIM196-842D17.
NUT HEX FLANGE 5/8-11 PLT803-196C18.
HOSE POST BASE, 40P196-370H19.
PIN COTTER3/16 X 1805-069C20.
WASHER FLAT 1 1/4 USS PLT804-035C21.
SWIVEL HOSE POST196-166H22.

Tongue and Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 9 - 196-286P

Table of Contents Part Number Index

Tongue To Wings

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20284

196-286P - 10 - 04/10/13

Table of Contents Part Number Index

Tongue To Wings

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20284
HHCS 1 1/4-7X6 1/2 GR5 PLT802-717C1.
NUT HEX 1 1/4-7 NYLON INSERT803-081C2.
U-BOLT 5/8-11 X 6 1/32 X 7 3/4806-039C3.
SLIDER BLOCK ADJUST SHIM196-842D4.
OUTSIDE TONGUESKID BLOCK817-542C5.
NUT HEX FLANGE 5/8-11 PLT803-196C6.
HYD HOSE CLAMP BRACKET502-068D7.
WASHER LOCK SPRING 5/16 PLT804-009C8.

Shown.HHCS 5/16-18X1 1/4 GR5802-010C9.

Used on clamp with larger hoses.HFSS 5/16-18X1 3/4 GR5802-094C9.
HOSE CLIP 13/16 ID800-064C10.
3N-40 TONGUEBLOCK SUPT BAR196-853D11.
HHCS 5/8-11X1 3/4 GR5802-053C12.

Tongue and Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 11 - 196-286P

Table of Contents Part Number Index

Wing To Center Frame

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20285

196-286P - 12 - 04/10/13

Table of Contents Part Number Index

Wing To Center Frame

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20285
NUT HEX SLOTTED 1 1/4 - 7803-079C1.
WASHER FLAT 1 1/4 USS PLT804-035C2.
PIVOTPIN RETAINER WASHER196-774D3.
40P TOOLBARPIVOT PIN196-652D4.

Includes pinsCYL REP 5X24X2 ROD (TIE)810-499C5.
NUT HEX 1-8 PLT803-031C6.
WASHER LOCK SPRING 1 PLT804-027C7.
HHCS 1-8X4 GR5802-073C8.
FOLD CYLINDER BASE LUG WLDMNT196-344H9.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C10.

Shown40P LH TOOLBAR WELDMENT196-349H11.
40P RH TOOLBAR WELDMENT196-350H11.
BUSHING 4.0X3.5X3.0 LONG SPLIT890-800C12.
ADAPTORNUT 3/4-16 X 5/8-11196-149D13.
NUT HEX JAM 3/4-16 UNF PLT803-235C14.
CYL 1.5X2.5X.75 ROD (TIE ROD)810-201C15.

HHCS 5/8-11X7 1/2 GR5802-146C16.
LOCK ARM WELDMENT196-048H17.
PIN COTTER1/8 X 1 1/4 PLT805-109C18.
WASHER FLAT 1 1/4 HOSE GUARD196-875D19.
WASHER FLAT 5/8 SAE PLT804-021C20.
SPRING COMP .906OD X 9 X .105W807-128C21.
PIN CLEVIS 5/8 X 2.77 USALBE805-028C22.
PIN CLEVIS 1/2 X 2 1/2 PLT805-192C23.
WASHER FLAT 1/2 SAE PLT804-016C24.
TRANSPORT LOCK LATCHBAR196-766D25.
PIN COTTER5/32 X 1 PLT805-019C26.
40P CENTER FRAME WELDMENT196-351H27.
PIN COTTER5/16 X 2 1/2805-085C28.
HHCS 3/4-10X7 GR5802-095C29.
NUT LOCK 3/4-10 PLT803-026C30.
GREASE ZERK STRAIGHT 1/4-28800-001C31.
SPACER WASHER196-775D32.
FOLD CYL ADJUSTMENT SHIM196-777D33.
PIN COTTER1/4 X 2 1/2 PLT805-105C34.
WASHER FLAT 1 USS PLT804-028C35.
TOOLBAR LOCK BAR196-896D36.
NUT HEX 3/4-10 PLT803-027C37.
NUT HEX 5/16-18 PLT803-008C38.
WASHER LOCK SPRING 5/16 PLT804-009C39.
HHCS 5/16-18X1 GR5802-159C40.
HHCS 1 1/4-7X4 1/2 GR5802-273C41.
NUT HEX 1 1/4-7 PLT803-034C42.
GREASE ZERK 1/4-28 X 90-DEG800-073C43.
HOSE GUARDCAP196-050H44.
SPRING LEVER807-007C45.
TOOLB LOCK ARM WELDM196-377H46.
MIDWAYROD CLEVIS 3/4-16 UNF810-491C47.
NUT LOCK 3/8-16 PLT803-013C48.
WASHER FLAT 3/4 USS PLT804-024C49.
HHCS 3/8-16X2 1/4 GR5802-382C50.
PIN CLEVIS 5/8 X 2 1/2 PLT805-141C51.
RPBY 196-409H196-393H52.
CYL PIN NR 1.25X3.63USBX3.13CH196-392H53.
NUT HEX JAM 3/4-10 PLT803-048C54.
U-BOLT 3/8-16X 6.13 X 6.25 RND806-194C55.

Referto "Hydraulic Cylinder(810-496C

5x16x1.5 Rod)"

Tongue and Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 13 - 196-286P

Table of Contents Part Number Index

Wing To Center Frame (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

NUT HEX 3/8-16 PLT803-014C56.
WASHER LOCK SPRING 3/8 PLT804-013C57.
40P LH WING FRAME WELDMENT196-338H58.
40P RH WING FRAME WELDMENT196-339H58.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 14 - 04/10/13

Table of Contents Part Number Index

Wing To Center Frame (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

This Page Intentionally Left Blank

Tongue and Frame

04/10/13 - 15 - 196-286P

Table of Contents Part Number Index

Rockshaft

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20280

196-286P - 16 - 04/10/13

Table of Contents Part Number Index

Rockshaft

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20280
40P ROCKSHAFT WELDMENT196-319H1.
CYLINDER LOCK CHANNEL 1 1/2X16196-289H2.
SPINDLE SGL 2.73X15.97815-099C3.
HUB STUD 5/8-18X2 1/2 GR5802-182C4.
8-BOLT WHEEL HUB MACH.200-006D5.
GREASE CAPP5020016.
NUT LUG 5/8-18 X 90 DEG PLT803-219C7.

Includes: 16-18RH TIRE/RIM 395/55B16.5 SKID 8196-272K8.

Includes: 16-18LH TIRE/RIM 395/55B16.5 SKID 8196-273K9.
HHCS 3/4-10X5 GR5802-069C10.
NUT HEX 3/4-10 PLTNYLOCK803-025C11.
HUB 8 BOLT 5790# W/CUPS&STUDS815-101C12.
BRG CONE 2.00IDX1.18WD #3780822-036C13.
BRG CONE 1.31IDX1.01WD #2790822-038C14.

Formerly 805-152CPIN 3/8 X 3 USABLE LW/PIN805-001C15.
TIRE SKID ST 395/55B16.5 NHS814-206C16.
RIM 16.5X12, 8 BLT6 PILT 8 BC814-208C17.
VALVE STEM METAL TR-575 TUBLES814-210C18.
BRG CUP 3.67ODX.93WD #3720822-037C19.
BRG CUP 3.00ODX.75WD #2720822-039C20.
7/8 SPINDLE WASHER, HARDENED181-064D21.
NUT HEX SLOTTED 7/8-14 PLT803-029C22.
PIN COTTER3/16 X 1 1/4 PLT805-016C23.
8-BOLT HUB SEAL816-019C24.
GREASE ZERK STRAIGHT 1/4-28800-001C25.

Includes: 3-6, 12-14, & 14-19HUB & SPINDLE ASY 8 BOLT 5790#815-103C26.

Rockshaft

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 17 - 196-286P

Table of Contents Part Number Index

Rockshaft To Frame

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20281

196-286P - 18 - 04/10/13

Table of Contents Part Number Index

Rockshaft To Frame

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20281
DEPTH STOPTUBE BRACKET196-907D1.
STROKE CONTROLPADDLE WLDMT196-298H2.
DEPTH STOPSLIDE TUBE196-905D3.
KNOB 1/2-13 MALE THD 2 3/8OD817-455C4.
U-BOLT 5/8-11 X 4 1/32 X 3 3/8806-019C5.
DEPTH VALVE MOUNT196-381H6.
NUT HEX 5/8-11 PLT803-021C7.
WASHER LOCK SPRING 5/8 PLT804-022C8.
VALVE, STROKE CTRL 35 GPM -12810-503C9.
DEPTH STOPCURVED LINK PLATE196-904D10.
40P ROCKSHAFT PIN WELDMENT196-288H11.
PIN ROLL 3/8 X 2 PLT805-249C12.
BUSHING 1 1/2 X 1 1/4 X 1 1/2890-122C13.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C14.
CYL REP 5X16X1.5 ROD (TIE)810-496C15.

RHSNB 1/2-13X5 GR5802-463C16.
NUT HEX 5/16-18 PLT803-008C17.
GREASE ZERK STRAIGHT 1/4-28800-001C18.
U-BOLT 1/2-13 X 6 1/32 X 7 1/4806-060C19.
NUT HEX 1/2-13 PLT803-020C20.
WASHER LOCK SPRING 1/2 PLT804-015C21.
HEIGHT SWITCH CAM NO CLP 2.25817-476C22.
CLAMP WRM DRV #40 SS (2.06-3)800-144C23.
NUT HEX 10-24 PLT803-001C24.
2SNT IMPLEMENT SWITCH823-198C25.
SCREW PAN HD 1/4-20 X 3/4801-005C26.
HHCS 3/8-16X2 3/4 GR5802-216C27.
TUBE RND CREW 3/4ODX12GX3.25196-906D28.
CYL PIN NR 1.25X3.09X2.63 W/GR196-409H29.
CYL PIN NR 1.25X3.72USBX3.13CH196-391H30.
WASHER FLAT 1 1/4 USS PLT804-035C31.
PIN COTTER1/4 X 2 1/2 PLT805-105C32.
803-184 FLG TP LK 5/16-18ZNYCR803-177C33.
HHCS 5/16-18X2 GR5802-115C34.
BAR FLT HR 3/16X1 3/4X4.88196-911D35.
WASHER LOCK SPRING 5/16 PLT804-009C36.

Includes pins and clips Refer to

"Hydraulic Cylinder (810-497C

4.75x16x1.5 Rod)"

Rockshaft

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 19 - 196-286P

Table of Contents Part Number Index

Rear Axle Assembly

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20282

196-286P - 20 - 04/10/13

Table of Contents Part Number Index

Rear Axle Assembly

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20282
40P REAR AXLE WLDMT196-106H1.
HHCS 5/16-18X1 1/4 GR5802-010C2.
WASHER LOCK SPRING 5/16 PLT804-009C3.
HYD HOSE CLAMP BRACKET502-068D4.
NUT HEX 1 1/2-6 PLT803-073C5.
WASHER LOCK 1 1/2 PLT804-197C6.
NUT HEX JAM 1 1/2-6 PLT803-063C7.
EYEBOLT WELDMENT196-293H8.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C9.
CYL REP 4.5X16X1.5 ROD (TIE)810-498C10.

GREASE ZERK STRAIGHT 1/4-28800-001C11.
CYL LOCK CHANNEL 1 1/2X17 3/4196-292H12.

40P TOOLBARPIVOT PIN196-652D14.
HHCS 1-8X18 GR5802-728C15.
PIVOTPIN RETAINER WASHER196-774D16.
WASHER FLAT 1 1/4 USS PLT804-035C17.
NUT HEX SLOTTED 1 1/4 - 7803-079C18.
40P CASTER INNER PIVOT TUBE196-654D19.
WASHER LOCK SPRING 1 PLT804-027C20.
NUT HEX 1-8 PLT803-031C21.
40P CASTER PARALLEL ARM WLDMT196-287H22.
BUSHING 1 7/8X1 5/8X1 1/2 SPLT890-666C23.
WASHER FLAT 1 SAE804-029C24.
HHCS 1/2-13X1 1/4 GR5802-034C25.
WASHER LOCK SPRING 1/2 PLT804-015C26.
NTA CASTER RETAINER CAP161-231D27.
STEEL BUSHING 3 1/4X3IDX3LONG890-193C28.
40P CASTER SUPPORT WLDMT196-329H29.
PIVOTTHRUST WASHER804-102C30.
REAR CASTER SUPT WLDMT196-397H31.

HHCS 3/4-10X5 GR5802-069C33.
NUT HEX 3/4-10 PLTNYLOCK803-025C34.

40P RADARMOUNT WLDMT196-294H37.
CASTER SPRING PLUNGER196-769D38.
SPRING COMP 1.88OD x .362W807-143C39.
CASTER DETENT PIN196-770D40.
HHCS 3/4-10X2 GR5802-064C41.
WASHER LOCK SPRING 3/4 PLT804-023C42.
NUT HEX 3/4-10 PLT803-027C43.
HHCS 3/4-10X6 GR5802-070C44.
NUT LOCK 3/4-10 PLT803-026C45.
PIN COTTER5/16 X 2 1/2805-085C46.
HHCS 3/4-10X4 GR5 FTHD802-067C47.
SPACER WASHER196-775D48.
RPBY 196-409H196-393H49.
CYL PIN NR 1.25X3.63USBX3.13CH196-392H50.
WASHER FLAT 1 USS PLT804-028C51.
PIN COTTER1/4 X 2 1/2 PLT805-105C52.
HHCS 1/4-28X3/8 GR5802-300C53.
NUT HEX JAM 3/4-10 PLT803-048C54.
HHCS 1/2-13X2 GR5802-128C55.
REAR CASTER LOCK PLTHARDENED196-870D56.

Refer to "Hydraulic Cylinder (810-499

5x24x2 Rod)" for breakdown

Formerly 805-152CPIN 3/8 X 3 USABLE LW/PIN805-001C13.

Refer to "Rockshaft"LH TIRE/RIM 395/55B16.5 SKID 8196-273K32.

Refer to "Rockshaft"HUB & SPINDLE ASY 8 BOLT 5790#815-103C35.

Refer to "Rockshaft"RH TIRE/RIM 395/55B16.5 SKID 8196-272K36.

Rockshaft

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 21 - 196-286P

Table of Contents Part Number Index

Rear Axle Assembly (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

NUT HEX 1/2-13 PLT803-020C57.

Includes: 26, 31, 40, & 55-57REAR CASTER & HARD LCK PLTKIT196-394L58.

BUSHING 4.0X3.5X3.0 LONG SPLIT890-800C59.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 22 - 04/10/13

Table of Contents Part Number Index

Rear Axle Assembly (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

This Page Intentionally Left Blank

Rockshaft

04/10/13 - 23 - 196-286P

Table of Contents Part Number Index

Gauge Wheel

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20283

196-286P - 24 - 04/10/13

Table of Contents Part Number Index

Gauge Wheel

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20283
40P LOCK CASTER SUPPORT WLDMT196-325H1.
CASTER LOCK LUG196-767D2.

STEEL BUSHING 3 1/4X3IDX3LONG890-193C4.
PIVOTTHRUST WASHER804-102C5.

(Shown) Left wingLH LOCKING CASTER SUPT WLDMT196-398H6.

Right wingRH LOCKING CASTER SUPT WLDMT196-399H6.
CASTER LOCK RAMP196-768D7.
CASTER DETENT PIN196-770D8.
HHCS 1-8X18 GR5802-728C9.
WASHER FLAT 1 SAE804-029C10.
CASTER SPRING PLUNGER196-769D11.
HHCS 3/4-10X4 GR5 FTHD802-067C12.
WASHER FLAT 5/8 SAE PLT804-021C13.
PIN CLEVIS 5/8 X 3 1/2805-334C14.
PIN COTTER1/8 X 1 1/4 PLT805-109C15.
WASHER LOCK SPRING 1 PLT804-027C16.
NUT HEX 1-8 PLT803-031C17.
HHCS 1/2-13X1 1/4 GR5802-034C18.
WASHER LOCK SPRING 1/2 PLT804-015C19.
NTA CASTER RETAINER CAP161-231D20.
40P CASTER INNER PIVOT TUBE196-654D21.
BUSHING 1 7/8X1 5/8X1 1/2 SPLT890-666C22.
40P CASTER PARALLEL ARM WLDMT196-287H23.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C24.
EYEBOLT WELDMENT196-293H25.
NUT HEX JAM 1 1/2-6 PLT803-063C26.
WASHER LOCK 1 1/2 PLT804-197C27.
NUT HEX 1 1/2-6 PLT803-073C28.
40P GW SWIVEL PIN196-653D29.
PIVOTPIN RETAINER WASHER196-774D30.
WASHER FLAT 1 1/4 USS PLT804-035C31.
NUT HEX SLOTTED 1 1/4 - 7803-079C32.

(Shown) Left Wing40P CASTER SWIVEL MOUNT LH196-333H33.

Right Wing40P CASTER SWIVEL MOUNT RH196-328H33.
HHCS 1/2-13X2 GR5802-128C34.

(Shown) Left WingCASTER LOCK PLT LH HARDENED196-872D35.

Right WingCASTER LOCK PLT RH HARDENED196-873D35.
NUT HEX 1/2-13 PLT803-020C36.
CYL REP 4.75X16X1.5 ROD (TIE)810-497C37.

HHCS 1-8X18 GR5802-728C38.

GREASE ZERK STRAIGHT 1/4-28800-001C40.
NUT LUG 5/8-18 X 90 DEG PLT803-219C41.
RPBY 196-409H196-393H42.
CYL PIN NR 1.25X3.63USBX3.13CH196-392H43.
PIN COTTER1/4 X 2 1/2 PLT805-105C44.

CYL 1.5X2.5X.75 ROD (TIE ROD)810-201C46.

NUT HEX FLANGE LOCK 3/4-10 PLT803-181C47.
MIDWAYROD CLEVIS 3/4-16 UNF810-491C48.

SPRING COMP 1.88OD X .362W807-143C50.

Referto "Hydraulic Cylinder(810-498C

4.5x16x1.5 Rod)"

Includes 6, 8, 19, 34, 35, 36FRNT CASTR LH&HARD LCK PLT KIT196-395L39.

Includes 6, 8, 19, 34, 35, 36FRNT CASTR RH&HARD LCK PLT KIT196-396L39.

Refer to "Rockshaft"RH TIRE/RIM 395/55B16.5 SKID 8196-272K45.

Referto "Hydraulic Cylinder(810-496C

5x16x1.5 Rod)"

Refer to "Rockshaft"HUB & SPINDLE ASY 8 BOLT 5790#815-103C49.

Rockshaft

RevisionCommentsPart DescriptionPart No.Ref.

2nd rev.S/N 1046PP+CASTER LOCK ARM EXTEND196-376H3.
1st rev.S/N 1045PP-CASTER LOCK ARM WELDMENT196-343H3.

04/10/13 - 25 - 196-286P

Table of Contents Part Number Index

Gauge Wheel (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

SPRING COMP 1.4OD .162W 3LG807-212C51.
HHCS 1/4-28X3/8 GR5802-300C52.
HHCS 3/4-10X5 GR5802-069C53.
NUT HEX 3/4-10 PLTNYLOCK803-025C54.

Refer to "Rockshaft"LH TIRE/RIM 395/55B16.5 SKID 8196-273K55.
PIN COTTER5/16 X 2 1/2805-085C56.
PIN 3/4 X 4 13/32 USEABLE805-230C57.

Refer to "Lock Cylinder Hydraulics"CYL REP 5X20X2 ROD (TIE)810-500C58.
WASHER FLAT 1 USS PLT804-028C59.
HHCS 3/4-10X6 GR5802-070C60.
NUT LOCK 3/4-10 PLT803-026C61.
NUT HEX JAM 3/4-10 PLT803-048C62.
HHCS 1-8X3 GR5802-368C63.
NUT HEX JAM 1-8 PLT803-030C64.
HOSE LOOP 2 5/8 WITH TAB160-018H65.
NUT HEX 5/8-11 PLT803-021C66.
WASHER LOCK SPRING 5/8 PLT804-022C67.
HHCS 5/8-11X2 GR5802-055C68.
HHCS 5/8-11X5 GR5802-062C69.
NUT HEX NYLOCK 5/8-11 PLT803-148C70.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 26 - 04/10/13

Table of Contents Part Number Index

Gauge Wheel (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

This Page Intentionally Left Blank

Rockshaft

04/10/13 - 27 - 196-286P

Table of Contents Part Number Index

Gauge Wheel Locking Plate

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20364

196-286P - 28 - 04/10/13

Table of Contents Part Number Index

Gauge Wheel Locking Plate

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20364
U-BOLT 5/8-11 X 4 1/32 X 3 3/8806-019C1.
TONGUE SPACERSHIM196-782D2.
WING RUBBLOCK196-800D3.
NUT HEX FLANGE LOCK 5/8-11 PLT803-263C4.

Shown40P CASTER SWIVEL MOUNT LH196-333H5.
40P CASTER SWIVEL MOUNT RH196-328H5.
TUBE RND 1 1/4ODX3/16X1.05196-891D6.
GW SWIVEL LOCK LUG196-856D7.
HHCS 3/8-16X2 GR5802-143C8.
HHCS 7/8-9X1 1/2 GR5802-622C9.
PIN SPIROL 1/2X2 1/2 PLAIN805-037C10.
GW SWIVEL LOCK SPREADER LINK196-859D11.
WASHER LOCK SPRING 7/8 PLT804-037C12.
HHCS 7/8-9X2 3/4 GR8802-275C13.
NUT LOCK 5/8-11 PLT803-024C14.
GW SWIVEL LOCK SLOT LINK196-858D15.
WASHER FLAT 5/8 USS PLT804-019C16.
HHCS 5/8-11X2 3/4 GR5802-281C17.
SPRING EXT 1 7/8ODX8 3/8X.25W807-113C18.
GW SWIVEL LOCK CYL ROD PLT196-857D19.
NUT HEX JAM 3/4-16 UNF PLT803-235C20.
CYL 1.5X2.5X.75 ROD (TIE ROD)810-201C21.

HOSE LOOP 2 5/8 WITH TAB160-018H22.
HHCS 5/8-11X1 1/4 GR5802-050C23.
WASHER LOCK SPRING 5/8 PLT804-022C24.
NUT HEX 5/8-11 PLT803-021C25.
HHCS 3/8-16X1 GR5802-017C26.
WASHER LOCK SPRING 3/8 PLT804-013C27.
WASHER FLAT 3/8 USS PLT804-011C28.
SPRING ANCHOR ANGLE196-889D29.
NUT HEX 3/8-16 PLT803-014C30.
SLEEVE IDLER PIVOT402-037D31.
BOX MOUNTING TUBE123-320D32.
CLOSED EYE BOLT 3/8-16X4 1/2802-674C33.
NUT HEX 7/8-9 PLT803-049C34.
HHCS 7/8-9X5 GR5802-546C35.

Referto "Hydraulic Cylinder(810-201C

1.5x2.5x.75 Rod)"

Rockshaft

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 29 - 196-286P

Table of Contents Part Number Index

Box To Frame

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20288

196-286P - 30 - 04/10/13

Table of Contents Part Number Index

Box To Frame

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20288

Shown40P LH WING FRAME WELDMENT196-338H1.
40P RH WING FRAME WELDMENT196-339H1.
40P SEED BOX WLDMNT197-155H2.
SEED BOX PARTITION118-402D3.
NUT HEX FLANGE 5/16-18 PLT803-199C4.
HFS 5/16-18X3/4 GR5802-387C5.
HANDLE119-190D6.
HFSS 1/2-13X1 1/2 GR5802-203C7.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C8.
HHCS 1/2-13X1 1/4 GR5802-034C9.
WASHER LOCK SPRING 1/2 PLT804-015C10.
NUT HEX 1/2-13 PLT803-020C11.
TALC LUBRICANT-5 GAL CONTAINER821-048C12.
EZEE-GLIDE PLUS LUBRICANT-5GAL821-069C12.
BOX PARTITION UPPER PAD118-052H13.
3N-40P BOX GUSSET RH197-290D14.
3N-40P BOX GUSSET LH197-289D15.
HFSS 1/2-13X1 1/4 GR8802-083C16.
HFSS 1/4-20X5/8 GR5802-196C17.
NUT HEX LOCK 1/4-20 FLG803-088C18.

Box To Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 31 - 196-286P

Table of Contents Part Number Index

Box Components

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20289

196-286P - 32 - 04/10/13

Table of Contents Part Number Index

Box Components

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20289
40P SEED LID 144 WLDMT197-166H1.
40P SEED BOX WLDMNT197-155H2.
HFS 5/16-18X3/4 GR5802-387C3.
NUT HEX FLANGE 5/16-18 PLT803-199C4.
BALL STUD 10MM X 5/16-18 X 1/2800-121C5.
12-20 X 90 LB GAS SPRING890-221C6.
NUT LOCK 5/16-18 PLT803-011C7.
LATCH CASTING MACHINED119-153D8.
SPRING .540 O.D.X 1 1/4 X.054W807-106C9.
LID HANDLE119-154D10.
WASHER FLAT 5/16 SAE PLT804-036C11.
HHCS 5/16-18X1 1/4 NYL802-425C12.
NUT FLANGE LOCK 3/8-16 PLT803-209C13.
LID HINGE PIVOT313-186D14.
LID HINGE BASE PLATE313-176D15.
HFS 3/8-16X1 GR5802-388C16.
RHSNB 3/8-16X2 GR5802-411C17.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C18.
HHCS 1/4-20X3/4 GR5802-004C19.
MINI END WHEEL PRESS WHEEL817-042C20.
NUT HEX FLNG T-LOCK 1/4-20 YLW803-293C21.
MANUAL PAK 1'" W/ GASKET817-516C22.
HFSS 1/2-13X1 1/2 GR5802-203C23.
12' EWNT LIGHT BRACKET150-138D24.
MANUAL PAK MOUNTING PLATE248-251D25.
DUAL AG LIGHTS LH890-311C26.
DUAL AG LIGHTS RH890-312C27.
SCREW HEX SELF TAP 1/4-20X3/4801-081C28.
AG LIGHT WIRING HARNESS-28'890-313C29.
LIGHT HARNESS, 10' WISHBONE890-390C30.
CABLE TIE .19X7.25 1.75D 50LB800-112C31.
CABLE TIE MOUNT800-148C32.
AG LIGHT HARNESS, EXT-15'890-600C33.

Box To Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 33 - 196-286P

Table of Contents Part Number Index

Seed Level Indicator

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

19187

196-286P - 34 - 04/10/13

Table of Contents Part Number Index

Seed Level Indicator

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg19187
SEED LEVEL ARM, 6 3/4R. TAB118-474H1.
FOAM FLOAT197-089D2.
SEED LEVEL CHAIN BRACKET197-091D3.
FOAM FLOAT WASHER197-096D4.
RIVET POP 1/8X.265LG FLG800-101C5.
HFS 10-24 X 1 1/8 PLTD801-096C6.
SCR HEX HD SHT MET #8 X 1/2801-154C7.
NUT HEX 10-24 PLT803-001C8.
NUT HEX NYLOCK 1/4-20803-255C9.
WASHER INTERNAL STAR #10 PLT804-004C10.
WASHER FLAT 1/4 USS PLT804-075C11.
PIN COTTER1/8 X 3/4805-067C12.
SEED LEVEL BUSHING817-086C13.
SEED LEVEL ARM MOUNT817-202C14.
SEED LEVEL INDICATOR817-350C15.
CABLE 3/64 X 11 5/8 W/ EYELETS890-305C16.

Box To Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 35 - 196-286P

Table of Contents Part Number Index

Walkboards And Steps

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20290

196-286P - 36 - 04/10/13

Table of Contents Part Number Index

Walkboards And Steps

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20290
40P WALKBOARD WLDMT196-297H1.

Shown40P LH WING FRAME WELDMENT196-338H2.
40P RH WING FRAME WELDMENT196-339H2.
NUT LOCK 1/2-13 PLT803-019C3.
HHCS 1/2-13X1 1/4 GR5802-034C4.
PIN CLEVIS 1/2 X 1 3/4805-127C5.
PIN HAIR COTTER .120 PLT805-143C6.
HHCS 3/8-16X1 1/4 GR5802-079C7.
WASHER FLAT 3/8 SAE PLT804-012C8.
NUT LOCK 3/8-16 NYLON INSERT803-078C9.
40P LADDER WLDMT196-299H10.
OPENER HANDLE HOLDER119-211D11.
PIN HAIR COTTER .148 WIRE805-032C12.
SPRING ADJ HANDLE WELDMENT198-810H13.
NUT FLANGE LOCK 3/8-16 PLT803-209C14.
HFS 3/8-16X1 GR5802-388C15.
U-BOLT 3/8-16 X 2 1/32 X 3806-166C16.
WASHER LOCK SPRING 3/8 PLT804-013C17.
NUT HEX 3/8-16 PLT803-014C18.
WALKBOARDFILLER STRIP196-886D19.
WALKBOARDFILLER CHANNEL196-887D20.
NUT HEX 5/16-18 PLT803-008C21.
WASHER LOCK SPRING 5/16 PLT804-009C22.
HHCS 5/16-18X1 GR5802-159C23.
40P WALKBOARD WLDMT196-297H24.

Box To Frame

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 37 - 196-286P

Table of Contents Part Number Index

10 & 20 Series Center Section Drive

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

20286

196-286P - 38 - 04/10/13

Table of Contents Part Number Index

10 & 20 Series Center Section Drive

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

Image No.dwg20286
VERIS PPC-40 CONTROLLER833-251C1.
COLLAR LOCK 7/8 HEX402-058D2.
SCREW SET 5/16-18 SKT KP X 3/8801-035C3.
LOCK COLLAR, 7/8 HEX W/ SET SC402-025S4.
SPKT 50C36 X 7/8 HEX BORE808-313C5.
SPKT 50C17 X 7/8 HEX BORE808-303C6.
CHAIN RL #50 99 PITCHES136-199D7.
RHSNB 5/16-18X1 GR5802-282C8.
FLANGETTE 52 3-BOLT PLT822-175C9.
BRG INS 7/8HEXX2.04OD SPH822-195C10.
803-184 FLG TP LK 5/16-18ZNYCR803-177C11.
WASHER FLAT 1/2 USS HARD PLT804-113C12.
WASHER LOCK SPRING 1/2 PLT804-015C13.
NUT HEX 1/2-13 PLT803-020C14.
IDLER SPOOL #50 2.38X1.01X.31817-456C15.
TUBE RND 1 OD X 7/32W X 2.13120-306D16.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C17.
SHAFT 7/8 HEX X 16.5120-001D18.
U-JOINT DRIVE SHAFT YOKE196-245H19.
SPKT 50A25 CLUTCH METRIC BORE808-357C20.
CHAIN RL #50 92 PITCHES136-200D21.
OGURA CLUTCH823-231C22.
40P CENTER CLUTCH SHAFT196-776D23.
PIN ROLL 1/4 X 1 1/2 LG PLT805-180C24.

WASHER MACH 1.50 X 1.00 X 18GA804-061C28.

HHCS 1/4-20X5 GR5 PLT802-085C30.
NUT-HEX 1/4-20 PLT803-006C31.
TUBE RND DOM. 1 OD X 7/32WX3.0120-293D32.
SPKT 50C22 X 7/8 HEX BORE808-306C33.
HEX SHAFT 7/8 X 162.0 LG PLT196-772D34.
VERIS DRIVE SUPPORT SPACER196-847D35.
HHCS 5/8-11X2 1/2 GR5802-058C36.
WASHER LOCK SPRING 5/8 PLT804-022C37.
NUT HEX 5/8-11 PLT803-021C38.
CLUTCH SPROCKET SPACER196-876D39.
WASHER FLAT 1/4 USS PLT804-075C40.
WASHER LOCK SPRING 1/4 PLT804-006C41.
KEY 1/4 X 3/16 X 3.80839-956C42.
BUSHING 1 1/8 ODX7/8 HEX BORE196-877D43.
TUBE RND 1 OD X 7/32W X 2.13120-306D44.
CLUTCH OIL SHIELD402-507D45.
BUTTON PLUG 7/8 ROUND HOLE817-813C46.

Drive

RevisionCommentsPart DescriptionPart No.Ref.

2nd rev.S/N 1045PP+SPKT 50C34 X 7/8 HEX BORE402-167H25.
1st rev.S/N 1044PP-SPKT 50C27 X 7/8 HEX BORE808-311C25.
2nd rev.S/N 1045PP+CHAIN RL #50 80 PITCHES136-220D26.
1st rev.S/N 1044PP-CHAIN RL #50 72 PITCHES136-202D26.

Use liquid thead lockerHSHCS M8X1.25X30 GR8.8 PLT802-775C27.

2nd rev.S/N 1045PP+SPKT 50B21 X 1 BORE W/KW, 2 SS808-294C29.
1st rev.S/N 1044PP-SPKT 50B17 X 1 BORE W/KW, 2 SS808-344C29.

04/10/13 - 39 - 196-286P

Table of Contents Part Number Index

HD10 & 25 Series Center Section Drive

(Applies to 3N-4025P only)

22510

196-286P - 40 - 04/10/13

Table of Contents Part Number Index

HD10 & 25 Series Center Section Drive

(Applies to 3N-4025P only)

Image No.dwg22510
VERIS PPC-40 CONTROLLER833-251C1.
COLLAR LOCK 7/8 HEX402-058D2.
SCREW SET 5/16-18 SKT KP X 3/8801-035C3.
LOCK COLLAR, 7/8 HEX W/ SET SC402-025S4.

CHAIN RL #50 92 PITCHES136-200D7.
RHSNB 5/16-18X1 GR5802-282C8.
FLANGETTE 52 3-BOLT PLT822-175C9.
BRG INS 7/8HEXX2.04OD SPH822-195C10.
803-184 FLG TP LK 5/16-18ZNYCR803-177C11.
WASHER FLAT 1/2 USS HARD PLT804-113C12.
WASHER LOCK SPRING 1/2 PLT804-015C13.
NUT HEX 1/2-13 PLT803-020C14.
IDLER SPOOL #50 2.38X1.01X.31817-456C15.
TUBE RND 1 OD X 7/32W X 2.13120-306D16.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C17.
SHAFT 7/8 HEX X 16.5120-001D18.
U-JOINT DRIVE SHAFT YOKE196-245H19.
SPKT 50A25 CLUTCH METRIC BORE808-357C20.
CHAIN RL #50 92 PITCHES136-200D21.
OGURA CLUTCH823-231C22.
40P CENTER CLUTCH SHAFT196-776D23.
PIN ROLL 1/4 X 1 1/2 LG PLT805-180C24.

HSHCS M8X1.25X30 GR8.8 PLT802-775C27.
WASHER MACH 1.50 X 1.00 X 18GA804-061C28.

HHCS 1/4-20X5 GR5 PLT802-085C30.
NUT-HEX 1/4-20 PLT803-006C31.
TUBE RND DOM. 1 OD X 7/32WX3.0120-293D32.
SPKT 50C22 X 7/8 HEX BORE808-306C33.
HEX SHAFT 7/8 X 162.0 LG PLT196-772D34.
VERIS DRIVE SUPPORT SPACER196-847D35.
HHCS 5/8-11X2 1/2 GR5802-058C36.
WASHER LOCK SPRING 5/8 PLT804-022C37.
NUT HEX 5/8-11 PLT803-021C38.
CLUTCH SPROCKET SPACER196-876D39.
WASHER FLAT 1/4 USS PLT804-075C40.
WASHER LOCK SPRING 1/4 PLT804-006C41.
KEY 1/4 X 3/16 X 3.80839-956C42.
BUSHING 1 1/8 ODX7/8 HEX BORE196-877D43.
SPLIT SPACER 1 ID X 1.25 THICK120-337S44.
TUBE RND 1 OD X 7/32W X 2.13120-306D45.
CLUTCH OIL SHIELD402-507D46.
BUTTON PLUG 7/8 ROUND HOLE817-813C47.

Drive

RevisionCommentsPart DescriptionPart No.Ref.

2nd rev.SPKT 50C36 X 7/8 HEX BORE808-313C5.

S/N 1045PP+SPKT 50C17 X 7/8 HEX BORE808-303C6.

2nd rev.S/N 1045PP+SPKT 50C34 X 7/8 HEX BORE402-167H25.
1st rev.S/N 1044PP-SPKT 50C27 X 7/8 HEX BORE808-311C25.
2nd rev.S/N 1045PP+CHAIN RL #50 80 PITCHES136-220D26.
1st rev.S/N 1044PP-CHAIN RL #50 72 PITCHES136-202D26.

2nd rev.S/N 1045PP+SPKT 50B21 X 1 BORE W/KW, 2 SS808-294C29.
1st rev.S/N 1044PP-SPKT 50B17 X 1 BORE W/KW, 2 SS808-344C29.

04/10/13 - 41 - 196-286P

Table of Contents Part Number Index

Wing Drive

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20298

196-286P - 42 - 04/10/13

Table of Contents Part Number Index

Wing Drive

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20298
PIN COTTER1/8 X 3/4805-067C1.
U-JOINT PIN 3/8195-157D2.
U-JOINT NYLATRON CROSS BLOCK817-273C3.
PIN ROLL 1/4 X 1 1/2 LG PLT805-180C4.
RPBY 800-124C800-311C5.
SLIDER SHAFT 7/8 HEX 44.50 LG196-581D6.
SEED HOSE X 45 RIBS816-107C7.
GREASE ZERK STRAIGHT 1/4-28800-001C8.
TELESCOPING DRIVE SHAFT TUBE196-246H9.
40P LH WING FRAME WELDMENT196-338H10.
40P WING CLUTCH STUB SHAFT196-773D11.
SHAFT 7/8 HEX GW PIVOT120-286D12.
WASHER MACH 1.50 X 1.00 X 18GA804-061C13.
RHSNB 5/16-18X1 GR5802-282C14.
FLANGETTE 52 3-BOLT PLT822-175C15.
BRG 7/8HEXX2.05OD SPH822-119C16.
803-184 FLG TP LK 5/16-18ZNYCR803-177C17.

Use liquid thead lockerHSHCS M8X1.25X30 GR8.8 PLT802-775C18.
SPKT 50A25 CLUTCH METRIC BORE808-357C19.
OGURA CLUTCH823-231C20.
SCREW SET 5/16-18 SKT KP X 3/8801-035C21.
COLLAR LOCK 7/8 HEX402-058D22.
LOCK COLLAR, 7/8 HEX W/ SET SC402-025S23.
WASHER FLAT 1/2 USS HARD PLT804-113C24.
WASHER LOCK SPRING 1/2 PLT804-015C25.
NUT HEX 1/2-13 PLT803-020C26.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C27.
TUBE RND DOM. 1 OD X 7/32WX3.0120-293D28.
IDLER SPOOL #50 2.38X1.01X.31817-456C29.
SPKT 50C36 X 7/8 HEX BORE808-313C30.
SPKT 50C17 X 7/8 HEX BORE808-303C31.
CHAIN RL #50 99 PITCHES136-199D32.

CHAIN RL #50 83 PITCHES136-201D33.
HHCS 1/4-20X5 GR5 PLT802-085C34.
NUT-HEX 1/4-20 PLT803-006C35.
HEX SHAFT 7/8 X 162.0 LG PLT196-772D36.
SPKT 50C22 X 7/8 HEX BORE808-306C37.
U-JOINT DRIVE SHAFT YOKE196-245H38.
WASHER FLAT 1/4 USS PLT804-075C39.
WASHER LOCK SPRING 1/4 PLT804-006C40.
CLUTCH ROTATION TAB196-866D41.
CLUTCH SPROCKET SPACER196-876D42.
BUSHING 1 1/8 ODX7/8 HEX BORE196-877D43.
KEY 1/4 X 3/16 X 3.80839-956C44.
HHCS 5/16-18X1 GR5802-159C45.
WASHER LOCK SPRING 5/16 PLT804-009C46.
NUT HEX 5/16-18 PLT803-008C47.
CLUTCH OIL SHIELD402-507D48.
BUTTON PLUG 7/8 ROUND HOLE817-813C49.

All opener except HD10 & 25 series

openers

HD10 & 25 series openersCHAIN RL #50 92 PITCHES136-200D32.

Drive

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 43 - 196-286P

Table of Contents Part Number Index

Veris Drive Components

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20299

196-286P - 44 - 04/10/13

Table of Contents Part Number Index

Veris Drive Components

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20299
CONTROLLER MOUNT 40' WELDMENT402-307H1.
MOTORMOUNT 40' WELDMENT402-306H2.
VERIS PROPORTIONAL CARTR 14GPMVER-197983.
VERIS COIL 12V WATERMAN CARTRVER-197994.
VERIS VLV BODYSAE-12-2X SAE-8VER-198005.
VERIS SOLENOID CABLEVER-183756.
VERIS EXT. CONTROLVER-215687.
FILTER ASM 5000PSI 6MI CANNIST810-657C8.
VERIS HYD LINE STL .5 OD X.049VER-52119.
VERIS MOTOR HYD 8.8 CIRVER-1985710.
VERIS ENCODER W/ CABLEVER-1838211.
AD 3/4FORB 7/8MORB811-564C12.
RPBY 810-696CVER-1955413.
AD 3/4MJIC 7/8MORB811-192C14.
HH1/2M3K 3/4FJIC 3/4FJIC90X168VER-2539015.
AD 3/4MJIC 1 1/16MORB811-205C16.
VERIS FTG HYD 8MB-8MJ90VER-518417.
VERIS BLT FLG SER8.8M8-1.25X16VER-1854818.
HFSS 1/2-13X1 1/2 GR5802-203C19.
NUT HEX WHIZ 1/2-13803-037C20.
RPBY 802-642CVER-441621.
803-184 FLG TP LK 5/16-18ZNYCR803-177C22.
HFSS 1/4-20X3/4 GR5802-257C23.
NUT HEX LOCK 1/4-20 FLG803-088C24.
VERIS BLT HH1/4-20NCX2.25GR5ZNVER-967925.
VERIS HYD HS 8M3K-8FJX90S-8FJXVER-258426.
VER FLTR ELEMENT PALL 6 MICRONVER-1985627.
AD 3/4MORB 3/4MJIC811-088C28.
EL 3/4MJIC 3/4MORB811-063C29.
DOUBLE SELECTORVALVE 3/4FORB810-274C30.

HH1/2R2 336 3/4MORB 3/4FJIC841-056C31.
TE 9/16MJIC 3/4MORB 9/16MJIC811-249C32.
HH1/4R1 095 9/16FJIC811-230C33.
HH1/4R1 048 9/16FJIC811-781C34.
SELECTOR VALVE MOUNT STRAP196-862D35.
HHCS 3/8-16X1 GR5802-017C36.
WASHER FLAT 3/8 USS PLT804-011C37.
WASHER LOCK SPRING 3/8 PLT804-013C38.
NUT HEX 3/8-16 PLT803-014C39.
HHCS 3/8-16X3 GR5802-024C40.

Refer to "Double Selector Valve

(810-274C)" forbreakdown

Drive

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 45 - 196-286P

Table of Contents Part Number Index

Veris Drive Controller

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20300

196-286P - 46 - 04/10/13

Table of Contents Part Number Index

Veris Drive Controller

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg20300

Includes Power Cable to BatteryVERIS CAB CONSOLEVER-279471.
VERIS MOUNTVER-195162.
VERIS SUCTION CUPVER-214633.
VERIS POWER/COMMCABLE 55'VER-214754.
VERIS EXT. CONTROLVER-215685.
DJ RADARW/HARDWARE833-179C6.
VERIS SOLENOID CABLEVER-183757.
VERIS PWR PRT ADPTR-HYD DRIVEVER-197298.
VERIS ENCODER W/ CABLEVER-183829.
DJ SE SEED MANAGER CONSOLE466822000S110.
CABLE EXT 25' RADAR GRD SPEED833-321C11.
DJ Y-CABLE CNH MAGNUM833-197C12.

Drive

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 47 - 196-286P

Table of Contents Part Number Index

10 & 20 Series Singulating Meter

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

18183

196-286P - 48 - 04/10/13

Table of Contents Part Number Index

10 & 20 Series Singulating Meter

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

Image No.dwg18183
NUT HEX FLANGE LOC 7/16-14 PLT803-229C1.
PSS IDLER INNER PIVOT TUBE402-282D2.
PRESS WHEEL ARM PIVOT BUSHING817-083C3.
PSS METER IDLER BRACKET WLDMT402-149H4.
IDLER 1 PC 2.38X1.01X1.062817-406C5.
SNAP RING EXT 1 HEAVY800-085C6.
HHCS 7/16-14X2 3/4 GR5802-315C7.
NUT HEX JAM NYLOCK 5/8-18 PLT803-302C8.
WOODRUFF KEY #606800-046C9.
SPKT 41B19 X 5/8 BORE W/KYWAY808-277C10.
BRG .63ID PRESS WHL ASY822-170C11.
PSS METER HUB403-056D12.
WASHER MACH 1.00 X .625 X 14GA804-111C13.
PSS METER WHEEL SUPPORT PLATE403-058D14.
PSS METER SHAFT SHORT403-057D15.

PIN ROLL 1/4 X 2 LG PL805-146C16.
PIN ROLL 1/8 X 1LG. PLT.805-080C17.
PSS SOYBEAN WHEEL 2700-3200403-061D18.
PSS SOYBEAN WHEEL 3100-3800403-066D18.
PSS SOYBEAN WHEEL 3600-4000403-068D18.
PSS SOYBEAN WHEEL 2200-2700403-070D18.
PSS SOYBEAN WHEEL 1700-2200403-071D18.
PSS MED RATE RICE-RIBBON403-142D18.

PSS MILO WHEEL 135 POCKETS403-081D18.
PSS MILO WHEEL 270 POCKETS403-082D18.
PSS MILO WHEEL 135 POCKETS403-090D18.
PSS MILO WHEEL 270 POCKETS403-091D18.
PSS WHEAT WHEEL-HIGH RATE403-085D18.
PSS WHEAT WHEEL403-060D18.
PSS VOLUMETRIC#3403-094D18.
PSS COTTON WHEEL 5200-6000403-076D18.
PSS COTTON WHEEL 4600-5200403-077D18.
PSS COTTON WHEEL 4000-4600403-078D18.
PSS CORN RNDS 1400-1900 28CELL403-083D18.
PSS CORN RNDS 1700-2200 28CELL403-096D18.

PSS CORN FLAT 1500-1675 28CELL403-086D18.
PSS CORN FLAT 1625-1800 28CELL403-088D18.
PSS LOWRATERICE-RIBBON403-425D18.
LOW RATE RICE-RIBBON-GRN403-426D18.
SPRING COMP 1.46ODX1.5X.112W807-187C19.
KNOB817-425C20.
PSS METER MOUNT PLATE FORMED403-053D21.
METER FRONT CAP817-403C22.
METER REAR CAP817-404C23.
SPRING COMP .39ODX.75LGX.047W807-186C24.

Meter

RevisionCommentsPart DescriptionPart No.Ref.

15 Series opener onlyBM PSS METER SHAFT403-063D15.

3rd rev.Use with part # 45 onlyPSSHIGH RATE RICE-RIBBON403-095D18.
2nd rev.PSS RICE WHEEL-MED RATE 2002403-089D18.
1st rev.PSS RICE WHEEL W/ RIVETS403-107V18.
2nd rev.PSS MILO WHEEL 51 POCKETS403-092D18.
1st rev.RPBY 403-092D403-079D18.
2nd rev.PSS MILO WHEEL 102 POCKETS403-093D18.
1st rev.RPBY 403-093D403-080D18.

3rd rev.PSS CORN RNDS 1700-2000 42CELL403-098D18.
3rd rev.PSS CORN RNDS 1400-1700 42CELL403-097D18.
2nd rev.PSS CORN RNDS 1400-1900 56CELL403-084D18.
1st rev.CORN WHL FLAT&RND -OBSOLETE-403-075D18.

04/10/13 - 49 - 196-286P

Table of Contents Part Number Index

10 & 20 Series Singulating Meter (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

METER SEED CUTOFF SLIDE817-405C25.
METER CLEANOUT DOOR817-402C26.
PSS METER COVER PLATE403-054D27.
SPRING EX 1ODX3.5LX.105 OFFSET807-185C28.
PSS METER TOP CAP FORMED403-055D29.
LOWER SEED TUBE GROMMET816-332C30.
METER SPACER .5X.141X1.062817-407C31.
HWHSTS #10-24X1/2 TYPE F SCREW801-160C32.
PIN CLEVIS 1/4 X 2 7/64 USBL805-182C33.
PIN CLEVIS 1/4 X 2 ADJUSTABLE805-298C34.
PIN CLEVIS 1/4X1 31/64 USBL805-296C35.
PIN HAIR COTTER .059W 15/16LG805-302C36.
PIN COTTER5/64 X 1/2805-297C37.
WASHER FLAT 1/4 SAE PLT804-007C38.
HHCS 5/16-18X3/4 GR5802-007C39.
WASHER LOCK SPRING 5/16 PLT804-009C40.
NUT HEX 5/16-18 PLT803-008C41.
SPRING COMP .39ODX.69LX.043WSS807-194C42.
CLIP, U-TYPE .156 PANEL X .63W800-319C43.

15 Series opener onlyBM METER SHAFT SPACER403-064D44.
Use with Wheel 403-095D onlyFLOW GATE817-529C45.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 50 - 04/10/13

Table of Contents Part Number Index

10 & 20 Series Singulating Meter (continued)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

This Page Intentionally Left Blank

Meter

04/10/13 - 51 - 196-286P

Table of Contents Part Number Index

HD10 & 25 Series Singulating Meter

(Applies to 3N-4025P only)

21858

196-286P - 52 - 04/10/13

Table of Contents Part Number Index

HD10 & 25 Series Singulating Meter

(Applies to 3N-4025P only)

Image No.dwg21858
25S SINGULATOR METER BACK PLT403-147D1.
OVER CENTER LATCH800-137C2.
HFSS 1/4-20X3/4 GR5802-257C3.
WASHER LOCK SPRING 1/4 PLT804-006C4.
NUT-HEX 1/4-20 PLT803-006C5.
PIN COTTER3/32 X 1/2805-307C6.
HWHSTS #10-24X1/2 TYPE F SCREW801-160C7.
PIN HAIR COTTER .059W 15/16LG805-302C8.
WASHER LOCK SPRING 5/16 PLT804-009C9.
NUT HEX 5/16-18 PLT803-008C10.
BRG .63ID PRESS WHL ASY822-170C11.
NUT HEX THIN 5/8-18 X 3/16 PLT803-345C12.
PIN, ROLL 1/4 X 1 1/4 LONG805-208C13.
PIN CLEVIS 1/4 X 2 ADJUSTABLE805-298C14.
WASHER FLAT 1/4 SAE PLT804-007C15.
METER FRONT CAP817-403C16.
METER REAR CAP817-404C17.
METER CLEANOUT DOOR817-402C18.
METER CLEANOUT SPACER817-548C19.
HHCS 5/16-18X1 GR5802-159C20.
PSS METER HUB403-056D21.
SPRING COMP .39ODX.75LGX.047W807-186C22.
SPRING COMP .39ODX.69LX.043WSS807-194C23.
PSS METER SPACERSHIELD817-549C24.
25S SINGULATOR METER OUTER PLT403-148D25.
WASHER MACH 1.00 X .625 X 14GA804-111C26.
PIN CLEVIS 1/4X1 31/64 USBL805-296C27.
PIN ROLL 1/4 X 2 LG PL805-146C28.
PSS METER Q/C DRIVE SHAFT403-117D29.
PSS METER WHEEL SUPPORT PLATE403-058D30.
PRECISION METER DUST FLAP817-564C31.
LOWER SEED TUBE GROMMET816-436C32.
METER TOPCAP403-114D33.
PIN CLEVIS 1/4 X 2 7/64 USBL805-182C34.
CORN RND 1400-1900 28CELL-GRN403-127D35.
CORN RND 1700-2200 28CELL-GRN403-128D35.
CORN FLT 1500-1675 28CELL-GRN403-131D35.
CORN FLT 1625-1800 28CELL-GRN403-132D35.
CORN RND 1400-1700 42CELL-GRN403-129D35.
CORN RND 1700-2000 42CELL-GRN403-130D35.
COTTONWHEEL 4000-4600-GRN403-133D35.
COTTONWHEEL 4600-5200-GRN403-134D35.
COTTONWHEEL 5200-6000-GRN403-135D35.
MILO WHEEL 51 CELL-GRN403-136D35.
MILO WHEEL 135 CELL-GRN403-140D35.
MILO WHEEL 135 CELL-GRN403-138D35.
MILO WHEEL 102 CELL-GRN403-137D35.
MILO WHEEL 270 CELL-GRN403-141D35.
MILO WHEEL 270 CELL-GRN403-139D35.
SOYBEANWHEEL 1700-2200-GRN403-122D35.
SOYBEANWHEEL 2200-2700-GRN403-123D35.
SOYBEANWHEEL 2700-3200-GRN403-124D35.
SOYBEANWHEEL 3100-3800-GRN403-125D35.
SOYBEANWHEEL 3600-4000-GRN403-126D35.
WHEAT WHEEL-GRN403-118D35.
WHEAT WHEEL-HIGH RATE-GRN403-119D35.
VOLUMETRIC #3-GRN403-120D35.

Meter

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 53 - 196-286P

Table of Contents Part Number Index

HD10 & 25 Series Singulating Meter (continued)

(Applies to 3N-4025P only)

SPRING COMP 1.46ODX1.5X.112W807-187C36.
KNOB817-425C37.
PIN ROLL 1/8 X 1LG. PLT.805-080C38.
METER SEED CUTOFF SLIDE817-405C39.
FLOW GATE817-529C40.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 54 - 04/10/13

Table of Contents Part Number Index

HD10 & 25 Series Singulating Meter (continued)

(Applies to 3N-4025P only)

This Page Intentionally Left Blank

Meter

04/10/13 - 55 - 196-286P

25 Series Corn Meter

(Applies to 3N-4025P only)

Table of Contents Part Number Index

21857

196-286P - 56 - 04/10/13

Table of Contents Part Number Index

25 Series Corn Meter

(Applies to 3N-4025P only)

Image No.dwg21857
25P FINGER PICKUP BACKING PLT403-116D1.
WASHER FLAT 1/4 SAE PLT804-007C2.
HHCS 1/4-20X3/4 GR5802-004C3.
HFSS 1/4-20X3/4 GR5802-257C4.
NUT HEX WHIZ 1/4-20 PLT803-194C5.
FINGER PICKUP METER DUST FLAP817-565C6.
PRECISION PL 12FP CORN METER890-856C7.

PRECISION PL 6FP CORN METER890-857C7.

PREC PL 12FP SUNFLOWER METER890-912C7.

NUT HEX LOCK 1/4-20 FLG803-088C9.
HFSS 1/4-20X2 GR5802-448C10.
PIN CLEVIS 1/4 X 2 7/64 USBL805-182C11.
METER TOPCAP403-114D12.
PIN COTTER3/32 X 1/2805-307C13.
PIN HAIR COTTER .059W 15/16LG805-302C14.
LOWER SEED TUBE GROMMET816-436C15.
OVER CENTER LATCH800-137C16.
CLEANOUT SPRING BUSHING403-150D17.
RIVET POP 3/16 .062-.251 LF800-220C18.
METER CLEANOUT COVER SPRING403-149D19.
WASHER FENDER 3/16 X 3/4804-206C20.

METER TOPCAP BACKING PLATE403-145D22.
25P FINGER PU METER COVER ASY817-563C23.
RIVET POP 3/16 .251-.375800-227C24.
NUT HEX JAM 1/4-20 PLT803-222C25.
METER SPACER TUBE403-338D26.

Meter

RevisionCommentsPart DescriptionPart No.Ref.

Refer to page (12FP Corn Meter

(890-856C) forbreakdown

Refer to page (6FP Corn Meter

(890-857C) forbreakdown

Refer to page (12FP Corn Meter

(890-856C) forbreakdown

Includes items 10, 17-2525S PREC FINGER PICKUP COVER403-125S8.

1 3/16" Cleanout HoleMETER CLEANOUT COVER817-568C21.

1 1/2" Cleanout HoleCORN METER CLEANOUT COVER817-607C21.

04/10/13 - 57 - 196-286P

Table of Contents Part Number Index

12FP Corn Meter (890-856C)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

28023

196-286P - 58 - 04/10/13

Table of Contents Part Number Index

12FP Corn Meter (890-856C)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg28023
NUT HEX WHIZ 1/4-20 PLT803-194C1.
PIN COTTER5/32 X 1 1/2 LONG805-089C2.
HHCS 1/4-20X1/2 GR2802-283C3.
PIN ROLL 3/16X 1 1/2 PLT805-024C4.
PIN, ROLL 1/4 X 1 1/4 LONG805-208C5.
HHCS 1/4-20X1 1/2 GR2802-221C6.
METER NUT COVER3430217.
5/8 METER NUT31114H10418.
FINGER ASSEMBLY 12 FINGER3430299.
METER STICKER900M0810.
POP MAX II BACK PLATE A INSERT34210311.
INSERT A34211012.

B INSERTFOR POPMAX II34210712.

C INSERTFOR POPMAX II34210812.

8-32 X 5/16 PAN HEAD SCREW3112886413.
SCREW .19 X 5/831121H129514.
ADJ BRUSHKIT34305215.
FINGER PICKUP BRUSH SCREW34303216.
DECAL 12 FINGER CORN848-118C17.
PRECISION BRG W/HOUSING34301118.
BELT HOUSING34300219.
BUSHING34300620.
ROLLER IDLER34300121.
DRIVE WHEEL PREC. PLANTING34306222.

METER COVER34300524.
PRECISION E CLIP34308925.
2007 SKIP STOP PAD34307326.
HHCS 1/4-20X1 GR5802-005C27.
HDWE FOR(4)2007 SKIP STOP PADS34309228.
REPLACED BY PRE16001134306029.

(Option) See your GP dealer for

application. (Standard insertforCorn)

(Option) See your GP dealer for

application.

(Option) See your GP dealer for

application.

Must be orientedas shownSURE FIRE BELT34306623.

Meter

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 59 - 196-286P

Table of Contents Part Number Index

6FP Corn Meter (890-857C)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

21991

196-286P - 60 - 04/10/13

Table of Contents Part Number Index

6FP Corn Meter (890-857C)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg21991
NUT HEX WHIZ 1/4-20 PLT803-194C1.
PIN COTTER5/32 X 1 1/2 LONG805-089C2.
HHCS 1/4-20X1/2 GR2802-283C3.
PIN ROLL 3/16X 1 1/2 PLT805-024C4.
PIN, ROLL 1/4 X 1 1/4 LONG805-208C5.
HHCS 1/4-20X1 1/2 GR2802-221C6.
METER NUT COVER3430217.
5/8 METER NUT31114H10418.
FINGER ASSEMBLY 6 FINGER CORN3430539.
STICKER900MO810.
POP MAX II BACK PLATE A INSERT34210311.
INSERT A34211012.

B INSERTFOR POPMAX II34210712.

C INSERTFOR POPMAX II34210812.

8-32 X 5/16 PAN HEAD SCREW3112886413.
SCREW .19 X 5/831121H129514.
ADJ BRUSHKIT34305215.
FINGER PICKUP BRUSH SCREW34303216.
PRECISION E CLIP34308917.
PRECISION BRG W/HOUSING34301118.
BELT HOUSING34300219.
BUSHING34300620.
ROLLER IDLER34300121.
DRIVE WHEEL PREC. PLANTING34306222.

METER COVER34300524.
REPLACED BY PRE16001134306025.
2007 SKIP STOP PAD34307326.
HHCS 1/4-20X1 GR5802-005C27.
HDWE FOR(4)2007 SKIP STOP PADS34309228.
DECAL 6 FINGER CORN848-119C29.

(Option) See your GP dealer for

application. (Standard insertforCorn)

(Option) See your GP dealer for

application.

(Option) See your GP dealer for

application.

Must be orientedas shownSUREFIRE SEED BELT34346623.

Meter

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 61 - 196-286P

Table of Contents Part Number Index

Seed Tray With Telescoping Tubes

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

18356

196-286P - 62 - 04/10/13

Table of Contents Part Number Index

Seed Tray With Telescoping Tubes

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg18356

10, 20 & 25 Series Twin Row40P SEED TRAY 7.5 TR CEN WLD118-845H1.

(S/N 1028PP-) 10, 20 Twin Row40P SEED TRAY 7.5 TR WING WLD118-846H1.

(S/N 1034PP+) 10, 20 & 25 Twin40P SEED TRAY 25TR WNG WLD118-910H1.

25 Series Twin Row40P SEED TRAY 25TR SPLT CTRWLD118-045H1.

25 Series Twin Row40P SEED TRAY 25TR SPLTWNG WLD118-043H1.

10, 20 & 25 Series40PSEED TRAY 15 CEN WLDMNT118-858H1.

10, 20 Series40P SEED TRAY 15 WING WLDMNT118-859H1.

25 Series40P SEED TRAY15 WING 25SERWLD118-047H1.
40P SEED TRAY 10 CEN WLDMNT118-843H1.
40P SEED TRAY 10 WING WLDMNT118-844H1.
40P SEED TRAY 7.5 CEN WLDMNT118-814H1.
40P SEED TRAY 7.5 WING WLDMNT118-629H1.
UPPER SEED TUBE GROMMET816-331C2.
CLAMP WRM DRV#28 SS (1.31-2.25)800-125C3.
PSS OUTER SLIDING SEED TUBE118-539D4.
PSS OUTER SLIDING SEED TB 9.42118-651D4.

PSS INNER SLIDING SEED TB 19.5817-577C5.

PSS INNER SLIDING SEED TB 23.5817-578C5.

CLAMP WRM DRV #24 SS (1.06-2)800-124C6.

Used on 25 series Mid (7" Stagger)

openers

Used on 25 series opener with

removable finger pickup meters

Used on 25 series opener with

removable singulator plus meters

Meter

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 63 - 196-286P

Table of Contents Part Number Index

10 Series Opener Arms & Mounts

(Applies to 3N-4010P & 3N-4010HDP only)

20334

196-286P - 64 - 04/10/13

Table of Contents Part Number Index

10 Series Opener Arms & Mounts

(Applies to 3N-4010P & 3N-4010HDP only)

Image No.dwg20334
HFS 1/2-13 X 5 3/4802-419C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
SING OPENER INNER PIVOT TUBE198-246D3.
PARALLEL ARM PIVOTBUSHING817-084C4.
SING OPENER LOWER ARM WELDMENT198-619H5.
SPRING EXT 1 5/8OD X 6.6X.177807-116C6.
6 13/16 SPRING STRAP198-239D7.
SING OPENER UPPER ARM WELDMENT198-618H8.
PSS OPENER MOUNT REAR WLDMT198-614H9.
PSS OPENER MOUNT FRONT WLDMT198-613H10.
HHCS 3/8-16X1 GR5802-017C11.

NUT FLANGE LOCK 3/8-16 PLT803-209C13.
HHCS 1/2-13X1 GR5802-258C14.
PSS METER ASSEMBLY403-104K15.

U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C18.
WASHER LOCK SPRING 5/8 PLT804-022C19.
NUT HEX 5/8-11 PLT803-021C20.
HHCS 3/8-16X2 1/2 GR5802-114C21.
IDLER SPACER TUBE 1/2OD X 1.56198-257D22.
IDLER SPOOL 1.44OD X.53B X1.5L817-480C23.

HHCS 1/4-20X3 GR5802-274C25.
NUT-LOCK 1/4-20 PLT803-007C26.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

2008-SPKT 41B12 7/8 HEX W/BEARING403-059D12.

2009+PEER 7/8 HEX BRG AND MNT822-239C12.

Front Opener.CHAIN RL #41 81 PITCHES136-160D16.

Rear Opener.CHAIN RL #41 124 PITCHES136-159D16.

Used with monitor seed tubes.CABLE TIE 2 DIA MIN - BLK800-303C17.

Center frame openers only10P20P UP FLOAT LIMITER122-172D24.

2009+SPKT 41C12 W/SS SPCL PLT808-395C27.

04/10/13 - 65 - 196-286P

Table of Contents Part Number Index

10 Series Opener Body

(Applies to 3N-4010P & 3N-4010HDP only)

20251

196-286P - 66 - 04/10/13

Table of Contents Part Number Index

10 Series Opener Body

(Applies to 3N-4010P & 3N-4010HDP only)

Image No.dwg20251
SEED DROP TUBE NO SENSOR HOLE817-413C1.
SEED TUBE W/DJ SENSOR 10&20198-738S2.
10 SERIES SINGULATING OPENER198-616H3.
PIN COTTER3/32 X 1 LONG805-063C4.
PIN CLEVIS 1/4 X 3 23/64 USBL805-299C5.
SEED FLAP MOUNTING CLIP, SING198-241D6.
SEED FLAP, RUBBER, SEED-LOK816-302C7.
SEED FLAP, UHMW, LONG817-349C7.
DD W/205 BRG-PLD FLNG-4MM107-138S8.
DD BRG FLANGE DUST COVER107-111D9.
WASHER MACH 1.19 X .63 X 18GA804-040C10.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C11.
PIN ROLL 5/16 X 5/8 PLT805-335C12.
SCRAPER-SPREADER 10-20 SER198-491H13.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C14.
HSG RIBB FLG 6BOLTPLT890-466C15.
BEARING AA205DD188-001V16.
FLAT DISK BLADE-4MM THICK820-256C17.
SEED DROP TUBE W/ SENSOR HOLE817-396C18.
DJ PLANTER STYLE SEED SENSOR833-222C19.
SEED TUBE GASKET, 10 SERIES816-383C20.
HHCS 3/8-16X1 1/4 GR5802-079C21.
NUT HEX 3/8-16 PLT803-014C22.
WASHER LOCK SPRING 3/8 PLT804-013C23.
10P AD OUTSIDE SCRAPER MOUNT122-169D24.
AIR DESIGN SCRAPER J.D.2.5W RHAD2101025.
AIR DESIGN SCRAPER J.D.2.5W LHAD2101126.
AIR DESIGN SCRAPER J.D.MNT RHAD2101227.
AIR DESIGN SCRAPER J.D.MNT LHAD2101328.
AIR DESIGN SCRAPER J.D.SPRINGAD2101429.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 67 - 196-286P

Table of Contents Part Number Index

15 Series Opener Arms & Mounts

(Applies to 3N-4015P only)

20380

196-286P - 68 - 04/10/13

Table of Contents Part Number Index

15 Series Opener Arms & Mounts

(Applies to 3N-4015P only)

Image No.dwg20380

SPKT 41B12 7/8 HEX W/BEARING402-284D2.
BM METER MOUNT PLATE403-062D3.
PARALLEL ARM WELD404-078H4.
SHANK WELD404-082H5.
TOP PARALLEL ARM WELD404-083H6.
GUIDE WELD404-084H7.
BM PSS STRUT BRACE WELDMENT404-118H8.
PARALLEL ARM PIVOTTUBE404-147D9.
SHAFT, SPRING MOUNT404-148D10.
15P LOWEREDBM OPNR MOUNT F173-225H11.
HHCS 3/8-16X1 GR5802-017C12.
HHCS 5/8-11X2 GR5802-055C13.
HHCS 5/8-11X2 1/4 GR5802-057C14.
NUT FLANGE LOCK 3/8-16 PLT803-209C15.
NUT HEX FLANGE LOCK 5/8-11 PLT803-263C16.
WASHER LOCK SPRING 3/8 PLT804-013C17.
WASHER FLAT 1 SAE804-029C18.
WASHER FLAT 5/8 HARD ASTMF436804-095C19.
PIN COTTER1/4 X 2 PLT805-021C20.
PIN ROLL 5/32 X 5/8 PLT805-186C21.
PIN CLEVIS 3/8 X 3 3/4 PLT805-277C22.
SPRING .540 O.D.X 1 1/4 X.054W807-106C23.
T-HANDLE ASSEMBLY817-328C24.
U-BOLT 5/8-11 X 7 1/32 X 6806-131C25.

EYE-BOLT 1/2-13 PLT802-655C28.
15P LOWEREDBM OPNR MOUNT R173-224H29.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Heavy dutyDOWN PRESSURE SPRING ASSY .312173-150S1.

MediumDOWN PRESSURE SPRING ASSY .262406-006S1.

Heavy dutySPRING HOLD DOWN HD COULTER807-055C26.

MediumSPRING EXT 2.21ODX.262X6.0807-178C26.

Heavy dutySPRING PLUG CASTING204-017D27.

MediumSPRING PLUG .250 DIA.406-010D27.

04/10/13 - 69 - 196-286P

Table of Contents Part Number Index

15 Series Opener Body

(Applies to 3N-4015P only)

20381

196-286P - 70 - 04/10/13

Table of Contents Part Number Index

15 Series Opener Body

(Applies to 3N-4015P only)

Image No.dwg20381
DD BRG FLANGE DUST COVER107-111D1.
RPBY 404-121S404-072S2.
SHIELD,DISK404-139D3.
SCRAPER, DISC RH404-152D4.
SCRAPER, DISC LH404-153D5.
RPBY 404-170H812-272C6.
RHSNB 5/16-18X3/4 GR5802-092C7.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C8.
NUT HEX WHIZ 5/16-18 PLT803-043C9.
WASHER MACH 1.19 X .63 X 18GA804-040C10.
PIN COTTER3/32 X 1 LONG805-063C11.
PIN ROLL 5/16 X 7/8805-250C12.
PIN CLEVIS 1/4 X 2 1/2 PLT805-278C13.
PIN ROLL 5/16 X 3/4 PLT805-280C14.
SHANK WELD404-082H15.
RPBY 820-187C820-155C16.
BEARING AA205DD188-001V17.
HSG RIBB FLG 6BOLTPLT890-466C18.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C19.
BM SEED TUBE W/DJ SENSOR ASSY403-106S20.
DJ PLANTER STYLE SEED SENSOR833-222C21.
BM PSS SEED TUBE W/ SENSOR HL817-415C22.
SEED FLAP CLIP-ROW UNIT404-183D23.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Used with Seed-Lok (Shown)SEED FLAP, RUBBER, SEED-LOK816-302C24.

Used with Seed-LokSEED FLAP, UHMW, LONG817-349C24.

04/10/13 - 71 - 196-286P

Table of Contents Part Number Index

15 Series Side Gauge Wheel

(Applies to 3N-4015P only)

18391

196-286P - 72 - 04/10/13

Table of Contents Part Number Index

15 Series Side Gauge Wheel

(Applies to 3N-4015P only)

Image No.dwg18391
ADJUSTMENT ASSY404-014S1.
RPBY 812-327C404-109S2.
UP-DOWN STOP404-118D3.
SPINDLE, GA WHL MNT ADJ404-119D4.
PIN, DEPTH CONTROL404-138D5.
ARM, GAUGE WHEEL404-155D6.
O-RING BUSHING404-171D7.
ECCENTRIC BUSHING404-174D8.
GREASE ZERK STRAIGHT 1/4-28800-001C9.
SNAP RING EXT 5/8 .050 T800-118C10.
SCREW SET SQ HD 1/2-13X1 1/2G5801-013C11.
HHCS 1/2-13X3 GR5802-039C12.
RHSNB 3/8-16X1 1/4 GR5802-155C13.
HHCS 5/8-11 X 3 GR8802-646C14.
HFS 1/2-13 X 1 1/2 GR8 NYL PLT802-663C15.
NUT HEX 1/2-13 PLT803-020C16.
NUT FLANGE LOCK 3/8-16 PLT803-209C17.
WASHER LOCK SPRING 1/2 PLT804-015C18.
WASHER LOCK SPRING 5/8 PLT804-022C19.
WASHER MACH 1.19 X .63 X 18GA804-040C20.
4 X 16 GAUGE TIRE ASSY-PLASTIC814-173C21.
O-RING 1 1/4ID X 1 1/2ODX1/8816-315C22.
803-184 FLG TP LK 5/16-18ZNYCR803-177C23.
4 X 16 GAUGE WHEEL RIM814-175C24.
4 1/2 X 16 GAUGE TIRE814-113C25.
BRG .63ID PRESS WHL ASY822-170C26.
4 X 16 GAUGE WHEEL RIM HALF817-331C27.
HFSS 5/16-18X1 GR5 PLT802-431C28.
HFSS 5/16-18X1 3/4 GR5802-094C29.
WALKBEAM404-077D30.
WALKBEAM PIVOT PIN404-079D31.
PIN ROLL 1/4 X 1 1/2 LG PLT805-180C32.
PIN ROLL 5/32 X 1 1/2 PLT805-290C33.
WALKBEAM MOUNT404-078D34.
WASHER 3/4 X 17/32 X 18 GA PLT804-100C35.
SPRING COMP .72 X 1.5 X .072WD807-119C36.
PIN COTTER3/32 X 1 LONG805-063C37.
PLANTER HANDLE404-020D38.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 73 - 196-286P

Table of Contents Part Number Index

15 Series Meter To Row Unit

(Applies to 3N-4015P only)

20382

196-286P - 74 - 04/10/13

Table of Contents Part Number Index

15 Series Meter To Row Unit

(Applies to 3N-4015P only)

Image No.dwg20382
15P IDLER MOUNT173-179D1.
IDLER SPACER TUBE 1/2OD X 1.56198-257D2.
PSS METER IDLER BRACKET WLDMT402-149H3.
PSS IDLER INNER PIVOT TUBE402-282D4.
BM METER IDLER MOUNT PLATE402-283D5.
BM METER ASSEMBLY403-105K6.
SNAP RING EXT 1 HEAVY800-085C7.
HHCS 1/2-13X1 1/4 GR5802-034C8.
HHCS 1/2-13X1 1/2 GR5802-091C9.
HHCS 7/16-14X2 3/4 GR5802-315C10.
HHCS 3/8-16X2 1/4 GR5802-382C11.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C12.
NUT FLANGE LOCK 3/8-16 PLT803-209C13.
NUT HEX FLANGE LOC 7/16-14 PLT803-229C14.
SPRING EX 1ODX3.5LX.105 OFFSET807-185C15.
PRESS WHEEL ARM PIVOT BUSHING817-083C16.
IDLER 1 PC 2.38X1.01X1.062817-406C17.
IDLER SPOOL 1.44OD X.53B X1.5L817-480C18.
CHAIN RL #41 102 PITCHES136-162D19.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 75 - 196-286P

Table of Contents Part Number Index

20 Series Opener Arms & Mounts

(Applies to 3N-4020P only)

20335

196-286P - 76 - 04/10/13

Table of Contents Part Number Index

20 Series Opener Arms & Mounts

(Applies to 3N-4020P only)

Image No.dwg20335
HFS 1/2-13 X 5 3/4802-419C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
SING OPENER INNER PIVOT TUBE198-246D3.
PARALLEL ARM PIVOTBUSHING817-084C4.
SING OPENER LOWER ARM WELDMENT198-619H5.

SING OPENER UPPER ARM WELDMENT198-618H8.
PSS OPENER MOUNT REAR WLDMT198-614H9.
PSS OPENER MOUNT FRONT WLDMT198-613H10.
HHCS 3/8-16X1 GR5802-017C11.

NUT FLANGE LOCK 3/8-16 PLT803-209C13.
HHCS 1/2-13X1 GR5802-258C14.
PSS METER ASSEMBLY403-104K15.

20 SER SING FRT INNER PIVOT TB198-247D17.

U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C19.
WASHER LOCK SPRING 5/8 PLT804-022C20.
NUT HEX 5/8-11 PLT803-021C21.
HHCS 3/8-16X2 1/2 GR5802-114C22.
IDLER SPACER TUBE 1/2OD X 1.56198-257D23.
IDLER SPOOL 1.44OD X.53B X1.5L817-480C24.

HHCS 1/4-20X3 GR5802-274C26.
NUT-LOCK 1/4-20 PLT803-007C27.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Used with 1x12 Press Wheels.SPRING EXT 1 5/8OD X 6.6X.177807-116C6.

Used with 1x10 Press Wheels.SPRING EXT 1.625ODX.243X9.875807-251C6.

Used with 1x10 Press Wheels.SPRING EXT 1.575O.D.X.225 WIRE807-076C6.

Used with 807-116C.6 13/16 SPRING STRAP198-239D7.

Used with 807-076C.3 13/32 SPRING STRAP198-240D7.

2008-SPKT 41B12 7/8 HEX W/BEARING403-059D12.

2009+PEER 7/8 HEX BRG AND MNT822-239C12.

Front openers.CHAIN RL #41 81 PITCHES136-160D16.

Rear openers.CHAIN RL #41 124 PITCHES136-159D16.

Used with monitor seed tubes.CABLE TIE 2 DIA MIN - BLK800-303C18.

Center frame openers only10P20P UP FLOAT LIMITER122-172D25.

2009+SPKT 41C12 W/SS SPCL PLT808-395C28.

04/10/13 - 77 - 196-286P

Table of Contents Part Number Index

20 Series Opener Body

(Applies to 3N-4020P only)

20350

196-286P - 78 - 04/10/13

Table of Contents Part Number Index

20 Series Opener Body

(Applies to 3N-4020P only)

Image No.dwg20350
SEED DROP TUBE NO SENSOR HOLE817-413C1.

20 SERIES SINGULATING OPENER198-615H3.
PIN COTTER3/32 X 1 LONG805-063C4.
PIN CLEVIS 1/4X1 31/64 USBL805-296C5.
SEED FLAP MOUNTING CLIP, SING198-241D6.

DD BRG FLANGE DUST COVER107-111D9.
WASHER MACH 1.19 X .63 X 18GA804-040C10.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C11.
PIN ROLL 5/16 X 5/8 PLT805-335C12.

RIVET,BUTTON HEAD 1/4 X 1/2800-213C14.
HSG RIBB FLG 6BOLTPLT890-466C15.
BEARING AA205DD188-001V16.
FLAT DISK BLADE-4MM THICK820-256C17.
20 SER OPNR CAM PIN198-202D18.
SNAP RING EXT 5/8 .050 T800-118C19.
RPBY 812-328C298-324S20.
CASTING - STAINLESS T-HANDLE812-302C21.
NUT HEX 7/16-20 GR8803-307C22.
WASHER LOCK 7/16 PLT804-014C23.
20 SER OPNR PW CAM198-201D24.
PRESS WHEEL ARM PIVOT BUSHING817-083C25.
SPRING COMP 5/8 OD X 1 3/4 LG807-172C26.
WASHER FLAT 3/8 SAE PLT804-012C27.
PIN COTTER1/8 X 3/4805-067C28.
20P SIDE DEPTH WHEEL ARM198-265D29.

WASHER LOCK SPRING 5/8 PLT804-022C31.
HFS 5/8-11X2 1/2 GR8 PLT802-729C32.

HFSS 5/16-18X1/2 GR5802-352C34.
NUT HEX WHIZ 5/16-18 PLT803-043C35.
2X13 D.W.OUTER RIM HALF814-082C36.
2X13 SIDE DEPTH TIRE814-083C37.
20 SER SIDE DEPTH WL STIFF PLT198-183D38.
2X13 D.W.INNER RIM HALF814-081C39.
HHCS 7/16-20 2 3/4 GR8802-694C40.
SEED DROP TUBE W/ SENSOR HOLE817-396C41.
DJ PLANTER STYLE SEED SENSOR833-222C42.

GREASE ZERK STRAIGHT 1/4-28800-001C44.
WASHER FLAT 1.31ODX.65IDX.188T804-195C45.
HHCS 5/8-11X2 GR5 NYL802-430C46.
RHSNB 5/16-18X3/4 GR5802-092C47.
U CUP SEAL816-723C48.
20P DEPTH WHL OUTER BUSHING298-001D49.
20P DEPTH WHL ECCENTRIC BUSHNG198-266D50.

WHEEL REINFORCING PLATE198-305D52.
BRG INS .63IDX1.57OD DBL LIP822-095C53.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Includes 42 & 43SEED TUBE W/DJ SENSOR 10&20198-738S2.

Used with Seed-Lok (shown).SEED FLAP, RUBBER, SEED-LOK816-302C7.

Used without Seed-Lok.SEED FLAP, UHMW, LONG817-349C7.

Includes 14,15,16 & 17DD W/205 BRG-PLD FLNG-4MM107-138S8.

S/N 7388B+SCRAPER-SPREADER 10-20 SER198-491H13.

S/N 7387B-SCRAPER-SPREADER 10-20SER 2003812-309C13.

Includes 48-5020P ELIMINATOR BUSHING ASSY198-998S30.

Includes 34,35,36,37,40, 47 & 522X13 DEPTH WHEEL ASSY198-057S33.

OptionSEP &FERTTUBE 10-20SER 1999122-257H43.

Includes 21, 24-2820 SER OPENER T-HANDLE SUBASSY198-956K51.

04/10/13 - 79 - 196-286P

Table of Contents Part Number Index

HD10 Series Opener Arms & Mounts

(Applies to 3N-4010P & 3N-4010HDP only)

23344

196-286P - 80 - 04/10/13

Table of Contents Part Number Index

HD10 Series Opener Arms & Mounts

(Applies to 3N-4010P & 3N-4010HDP only)

Image No.dwg23344
HD10P OPENER WELDMENT298-855H1.
HHCS 3/8-16X2 1/2 GR5802-114C2.
HFS 1/2-13X6 1/8GR5 PLT802-745C3.
IDLER SPOOL 1.44OD X.53B X1.5L817-480C4.
IDLER SPACER TUBE 1/2OD X 1.56198-257D5.
NUT FLANGE LOCK 3/8-16 PLT803-209C6.
PARALLEL ARM PIVOTBUSHING817-084C7.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C8.

25 SERIES UPPER PARALLEL ARM298-513H10.
SPRING EXT 1.575O.D.X.225 WIRE807-076C11.

25P REAR OPENER INNER PIVOTTB198-295D13.
25 SERIES LOWER PARALLEL ARM298-510H14.

HHCS 3/8-16X1 GR5802-017C16.
25P FRONT OPENER MOUNT WELDMT298-884H17.
U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C18.
NUT HEX 5/8-11 PLT803-021C19.
DRIVE MOUNT WELDMENT403-113H20.
DRIVE PLATE LINE-UP PIN403-107D21.

RHSNB 3/8-16X1 GR5802-015C23.
HHCS 3/8-16X2 1/4 GR5802-382C24.
NUT HEX 3/8-16 PLT803-014C25.
WASHER LOCK SPRING 3/8 PLT804-013C26.
HHCS 3/8-16X1 GR5802-017C27.
SPRING COMP DIE.75X.375X1LX515807-232C28.
SCR HX SKT BUT CP 3/8-16X3/4801-078C29.
9/16 OD DRIVE PLATE SPACER TB403-182D30.
PRESS WHEEL ARM PIVOT BUSHING817-083C31.
IDLER BRACKETWELDMENT403-115H32.
IDLER PIVOT 2.06 LONG891-191C33.
IDLER 1 PC 2.38X1.01X1.062817-406C34.
SNAP RING EXT 1 HEAVY800-085C35.
WASHER FLAT 3/8 SAE PLT804-012C36.
WASHER GRASS SEEDER CUP SHAFT804-042C37.
METER ALIGNMENT BUSHING403-108D38.
METER RETAINER LATCH PLATE403-112D39.
METER RETAINER PLATE403-111D40.
SPRING EXT. 1.0ODX5.OLX.095MW807-236C41.
HD10P REAR OPENER MOUNT WELDMT298-856H42.
CHAIN RL #41 90 PITCHES136-214D43.
CHAIN RL #41 132 PITCHES136-206D43.
WASHER LOCK SPRING 5/8 PLT804-022C44.
DRIVE JAW403-104D45.
19T SPROCKET HUB ASSY403-112H46.
DRIVE BEARING HOUSING403-116H47.
SNAP RING EXT 45MM800-365C48.
PIN ROLL 3/16 X 2 1/2 LG. PTL.805-062C49.
SPRING COMP .970ODX.063WX1.25807-174C50.
BRG BALL 45IDX7ODX16W822-210C51.
PIN HITCH 1 X 6 W/HAIRPIN805-033C52.
25P UP FLOATLIMITER122-173D53.
HHCS 3/8-16X1 1/4 GR5802-079C54.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Used with dual springs25P UPPER SPRING LINK198-292D9.

Used with dual springs25P LOWER SPRING LINK198-293D12.

2008-SPKT 41B12 7/8 HEX W/BEARING403-059D15.

2009+PEER 7/8 HEX BRG AND MNT822-239C15.

Includes 45-51DRIVE BEARING ASSEMBLY403-117S22.

2009+SPKT 41C12 W/SS SPCL PLT808-395C55.

04/10/13 - 81 - 196-286P

Table of Contents Part Number Index

HD10 Series Opener Arms & Mounts (continued)

(Applies to 3N-4010P & 3N-4010HDP only)

Used with single springs3 13/32 SPRING STRAP198-240D56.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 82 - 04/10/13

Table of Contents Part Number Index

HD10 Series Opener Arms & Mounts (continued)

(Applies to 3N-4010P & 3N-4010HDP only)

This Page Intentionally Left Blank

Openers

04/10/13 - 83 - 196-286P

Table of Contents Part Number Index

HD10 Series Opener Body

(Applies to 3N-4010P & 3N-4010HDP only)

23345

196-286P - 84 - 04/10/13

Table of Contents Part Number Index

HD10 Series Opener Body

(Applies to 3N-4010P & 3N-4010HDP only)

Image No.dwg23345
PIN ROLL 5/16 X 5/8 PLT
HD10P OPENER WELDMENT298-855H1.
CABLE TIE .19X7.25 1.75D 50LB800-112C2.
PIN COTTER3/32 X 1 LONG805-063C3.
T-HANDLE ASSEMBLY817-328C4.
PIN ROLL 5/32 X 5/8 PLT805-186C5.
SPRING .540 O.D.X 1 1/4 X.054W807-106C6.
OPENER TRUNION817-347C7.
PIN CLEVIS 3/8 X 2 1/8 USABLE805-154C8.

PIN ROLL 5/16 X 7/8805-250C10.
PIN ROLL 5/16 X 5/8 PLT805-335C11.
25P SCRAPER SEPARATOR WLDMT404-170H12.
RHSNB 5/16-18X3/4 GR5802-092C13.
NUT HEX WHIZ 5/16-18 PLT803-043C14.

WASHER MACH 1.19 X .63 X 18GA804-040C16.
BEARING AA205DD188-001V17.

4.0 MM 15 DISK (21 DEG BEVEL)820-287C18.
RIBB BRG FLNG .266 MT HOLE PLT890-466C19.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C20.

DD BRG FLANGE DUST COVER107-111D22.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C23.
PIN CLEVIS 1/4 X 2 1/2 PLT805-278C24.
RHSNB 1/2-13X1 GR5802-183C25.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C26.

DJ PLANTER STYLE SEED SENSOR833-222C28.
SEED TUBE 25S FPU TB&CAP W/ HL817-715C29.
SEED TUBE 25S HOOK CLIP198-331D30.
SEED FLAP, RUBBER, SEED-LOK816-302C31.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Includes items 28-30SEED TUBE FPU TB,CLIP & SENSOR403-214S9.

Used without Unit Mount CoulterTRASH GUARD WELDMENT288-310H15.

Includes 17-204.0 MM 15 DISC W/ 5/8 ASSY404-121S21.

Used with Unit Mount CoulterSHIELD, DISK404-139D27.

04/10/13 - 85 - 196-286P

Table of Contents Part Number Index

25 Series Opener Arms & Mounts

(Applies to 3N-4025P only)

22526

196-286P - 86 - 04/10/13

Table of Contents Part Number Index

25 Series Opener Arms & Mounts

(Applies to 3N-4025P only)

Image No.dwg22526
25 SERIES OPENER SHANK WELDMT298-509H1.
HHCS 3/8-16X2 1/2 GR5802-114C2.
HFS 1/2-13X6 1/8GR5 PLT802-745C3.
IDLER SPOOL 1.44OD X.53B X1.5L817-480C4.
IDLER SPACER TUBE 1/2OD X 1.56198-257D5.
NUT FLANGE LOCK 3/8-16 PLT803-209C6.
PARALLEL ARM PIVOTBUSHING817-084C7.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C8.
25P UPPER SPRING LINK198-292D9.

SPRING EXT 1.575O.D.X.225 WIRE807-076C11.
25P LOWERSPRING LINK198-293D12.
25P REAR OPENER INNER PIVOTTB198-295D13.

HHCS 3/8-16X1 GR5802-017C16.
RPBY 298-883S298-514H17.

U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C18.
NUT HEX 5/8-11 PLT803-021C19.
DRIVE MOUNT WELDMENT403-113H20.
DRIVE PLATE LINE-UP PIN403-107D21.

RHSNB 3/8-16X1 GR5802-015C23.
HHCS 3/8-16X2 1/4 GR5802-382C24.
NUT HEX 3/8-16 PLT803-014C25.
WASHER LOCK SPRING 3/8 PLT804-013C26.
HHCS 3/8-16X1 GR5802-017C27.
SPRING COMP DIE.75X.375X1LX515807-232C28.
SCR HX SKT BUT CP 3/8-16X3/4801-078C29.
9/16 OD DRIVE PLATE SPACER TB403-182D30.
PRESS WHEEL ARM PIVOT BUSHING817-083C31.
IDLER BRACKETWELDMENT403-115H32.
IDLER PIVOT 2.06 LONG891-191C33.
IDLER 1 PC 2.38X1.01X1.062817-406C34.
SNAP RING EXT 1 HEAVY800-085C35.
WASHER FLAT 3/8 SAE PLT804-012C36.
WASHER GRASS SEEDER CUP SHAFT804-042C37.
METER ALIGNMENT BUSHING403-108D38.
METER RETAINER LATCH PLATE403-112D39.
METER RETAINER PLATE403-111D40.
SPRING EXT. 1.0ODX5.OLX.095MW807-236C41.
RPBY 298-888S298-516H42.

RPBY 298-887S298-515H43.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

S/N 1053PP-25 SERIES UPPER PARALLEL ARM298-513H10.

S/N 1054PP+25 SERIES UPPER PARALLEL ARM288-374H10.

S/N 1053PP-25 SERIES LOWER PARALLEL ARM298-510H14.

S/N 1054PP+25 SRS LOWER PARALLEL ARM403-667D14.

2008-SPKT 41B12 7/8 HEX W/BEARING403-059D15.

2009+PEER 7/8 HEX BRG AND MNT822-239C15.

Used on front stagger 15" & 20" rows

1st Revision

2nd Revision25P FRONT OPENER MOUNT W/BUSH298-883S17.

Includes 46 - 52DRIVE BEARING ASSEMBLY403-117S22.

Used on rear stagger rows on 15" &

20" spacing alsoused on all30" rows
on 30" only spacing. Used on twin

row splitter openers. 1st Revision
2nd Revision25P MIDDLE OPENER MOUNT W/BUSH298-888S42.
Used on rearstagger rowsontwinrow

spacing1st Revision
2nd Revision25P REAR OPENER MOUNT W/BUSH298-887S43.
Front rowCHAIN RL #41 90 PITCHES136-214D44.
Middle row 7" staggerCHAIN RL #41 116 PITCHES136-215D44.
Rear row 14" staggerCHAIN RL #41 144 PITCHES136-216D44.

04/10/13 - 87 - 196-286P

Table of Contents Part Number Index

25 Series Opener Arms & Mounts (continued)

(Applies to 3N-4025P only)

WASHER LOCK SPRING 5/8 PLT804-022C45.
DRIVE JAW403-104D46.
19T SPROCKET HUB ASSY403-112H47.
DRIVE BEARING HOUSING403-116H48.
SNAP RING EXT 45MM800-365C49.
PIN ROLL 3/16 X 2 1/2 LG. PTL.805-062C50.
SPRING COMP .970ODX.063WX1.25807-174C51.
BRG BALL 45IDX7ODX16W822-210C52.
PIN HITCH 1 X 6 W/HAIRPIN805-033C53.
25P UP FLOATLIMITER122-173D54.
HHCS 3/8-16X1 1/4 GR5802-079C55.

2009+SPKT 41C12 W/SS SPCL PLT808-395C56.

RevisionCommentsPart DescriptionPart No.Ref.

196-286P - 88 - 04/10/13

Table of Contents Part Number Index

25 Series Opener Arms & Mounts (continued)

(Applies to 3N-4025P only)

This Page Intentionally Left Blank

Openers

04/10/13 - 89 - 196-286P

Table of Contents Part Number Index

25 Series Opener Body

(Applies to 3N-4025P only)

29770

196-286P - 90 - 04/10/13

Table of Contents Part Number Index

25 Series Opener Body

(Applies to 3N-4025P only)

Image No.dwg29770
SCRAPER, DISC LH404-153D1.
NUT HEX WHIZ 5/16-18 PLT803-043C2.
RHSNB 5/16-18X3/4 GR5802-092C3.
1/2-13X 1 3/4 SQ HD SS G5 PLTD801-164C4.
25P SEED TUBE W/DJ HR SENSOR817-604C5.
25P SCRAPER SEP WLDMT 3/8 FRT404-796H6.
PIN ROLL 5/16 X 5/8 PLT805-335C7.
PIN ROLL 5/16 X 7/8805-250C8.
WALKBEAM404-077D9.
DISK SHIELD404-198D10.
WALKBEAM PIVOT PIN404-079D11.
SPINDLE, GA WHL MNT ADJ404-119D12.

25P SIDE DEPTH WHL ARM SPINDLE198-288D12.

25P SIDE DEPTH WHEEL ARM198-289D13.

ARM, GAUGE WHEEL404-155D13.

GREASE ZERK STRAIGHT 1/4-28800-001C14.
HHCS 1/2-13X3 GR5802-039C15.
WASHER LOCK SPRING 1/2 PLT804-015C16.
NUT HEX 1/2-13 PLT803-020C17.
U CUP SEAL816-686C18.
OUTER BUSHING INNER CUP SEAL I198-360D19.

25P O-RING BUSHING404-214D19.

25P DEPTH WHL ECCENTRIC BUSHNG198-290D20.

ECCENTRIC BUSHING404-174D20.

HFS 1/2-13 X 1 1/2 GR8 NYL PLT802-663C22.

2.5X16 SIDE DEPTH WHEEL ASSY814-257C23.

3X16 SIDE DEPTH WHEEL ASSY814-260C23.

4 X 16 GAUGE TIRE ASSY-PLASTIC814-173C23.

HHCS 5/8-11X3 1/4 GR5802-160C24.

HHCS 5/8-11 X 3 GR8802-646C24.

WASHER MACH 1.19 X .63 X 18GA804-040C25.
WASHER LOCK SPRING 5/8 PLT804-022C26.
WASHER FLAT 1.31ODX.65IDX.188T804-195C27.
WALKBEAM MOUNT404-078D28.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C29.
DD BRG FLANGE DUST COVER107-111D30.

HHCS 1/2-13X1 GR5802-258C32.
SEED TUBE WITHOUT SENSOR HOLE817-606C33.
25P SEED TUBE W/HR SENSOR HOLE817-605C33.
SEED TUBE 25S FPU TB&CAP W/ HL817-715C33.
HHCS 1/2-13X1 1/2 GR5802-091C34.
1X12 PW ADJUSTER405-032D35.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

Used on wide row 15", 20" & 30"

openers
(Shown)Used on narrowrow,twinrow

& split row openers
(Shown)Used on narrowrow,twinrow

& split row openers
Used on wide row 15", 20" & 30"

openers

(Shown)Used on narrowrow,twinrow

& split row openers
Used on wide row 15", 20" & 30"

openers
(Shown)Used on narrowrow,twinrow

& split row openers
Used on wide row 15", 20" & 30"

openers
Used with Keeton seed firmerHHCS 5/16-18X2 1/2 GR5802-172C21.
Used with Seed-Lokor No seedfirmerRHSNB 5/16-18X3/4 GR5802-092C21.

Referto "Side DepthWheelAssembly"

for breakdown
Referto "Side DepthWheelAssembly"

for breakdown
Referto "Side DepthWheelAssembly"

for breakdown
Used on narrow row, twin row & split

row
Used on wide row 15", 20" & 30"

openers

Includes items 50 - 534.0 MM 15 DISC W/ 5/8 ASSY404-121S31.

04/10/13 - 91 - 196-286P

Table of Contents Part Number Index

25 Series Opener Body (continued)

(Applies to 3N-4025P only)

RPBY 199-146A199-108H36.

LONG PW MOUNT199-140H36.

SNAP RING EXT 5/8 .050 T800-118C37.
20 SER OPNR CAM PIN198-202D38.
PLANTER HANDLE404-020D39.
SPRING COMP .72 X 1.5 X .072WD807-119C40.
WASHER 3/4 X 17/32 X 18 GA PLT804-100C41.
PIN COTTER3/32 X 1 LONG805-063C42.
ADJUSTMENT ASSY404-014S43.

PIN ROLL 1/4 X 1 1/2 LG PLT805-180C44.
PIN ROLL 5/32 X 1 1/2 PLT805-290C45.
SCRAPER, DISC RH404-152D46.
CABLE TIE .19X7.25 1.75D 50LB800-112C47.
PIN CLEVIS 1/4 X 2 1/2 PLT805-278C48.
PIN COTTER3/32 X 1 LONG805-063C49.
HSG RIBB FLG 6BOLTPLT890-466C50.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C51.

4.0 MM 15 DISK (21 DEG BEVEL)820-287C52.
BEARING AA205DD188-001V53.
25P ECCENTRIC HEX ADJUSTER812-327C54.
RPBY 199-147A199-109H55.

25P MID PW MOUNT199-141H55.

DJ PLANTER STYLE SEED SENSOR833-222C57.
25 SERIES SEED FLAP CLIP404-189D58.

SEED FLAP, RUBBER, SEED-LOK816-302C60.
25P WIDE ELIMINATOR BUSHNG ASY298-881S61.
25P NARROW ELIMINATOR BUSH ASY298-882S61.
SEED TUBE 25S HOOK CLIP198-331D62.
ELBOW PTC 1/4 X 3/8830-424C63.

RevisionCommentsPart DescriptionPart No.Ref.

(S/N 1053PP-) Used on short (front)

row stagger on twin rows.

(S/N 1054PP+) Used on short (front)

row stagger on twin rows.

Includes items 9, 11, 28, 39 - 42, 44

& 45

(S/N1053PP-) Usedonrear (long) row

stagger rows on twin row & middle
row stagger on twin row splitter
openers

(S/N 1054PP+) Used on rear (long)

row stagger rows on twin row &
middle row stagger on twin row
splitter openers

Used on 15 series openerCLOSING WHEEL MOUNT404-164D56.

Replace with 816-302CSEED FLAP, UHMW, LONG817-349C59.

196-286P - 92 - 04/10/13

Table of Contents Part Number Index

25 Series Opener Body (continued)

(Applies to 3N-4025P only)

This Page Intentionally Left Blank

Openers

04/10/13 - 93 - 196-286P

Table of Contents Part Number Index

Side Depth Wheel Assembly

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

21993

196-286P - 94 - 04/10/13

Table of Contents Part Number Index

Side Depth Wheel Assembly

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

Image No.dwg21993
4 X 16 GAUGE TIRE ASSY-PLASTIC814-173C1.

2.5X16 SIDE DEPTH WHEEL ASSY814-257C2.
3X16 SIDE DEPTH WHEEL ASSY814-260C3.
803-184 FLG TP LK 5/16-18ZNYCR803-177C4.
4 X 16 GAUGE WHEEL RIM814-175C5.
4 1/2 X 16 GAUGE TIRE814-113C6.
BRG .63ID PRESS WHL ASY822-170C7.
4 X 16 GAUGE WHEEL RIM HALF817-331C8.
HFSS 5/16-18X1 3/4 GR5802-094C9.
HFSS 5/16-18X1 GR5 PLT802-431C10.
RHSNB 5/16-18X3/4 GR5802-092C11.
HFS 5/16-18X3/4 GR5802-387C12.

2.25X16'" TIRE FOR 814-257C814-258C13.

2.25X16'" RIM HALF FOR 814-257C814-259C14.
3X 16'" TIRE FOR 814-260C814-261C15.
3X16 NYLON WHEEL HALF-40MM817-541C16.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 95 - 196-286P

Table of Contents Part Number Index

10 & 20 Series Keeton Seed Firmer (Option)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

20252

196-286P - 96 - 04/10/13

Table of Contents Part Number Index

10 & 20 Series Keeton Seed Firmer (Option)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4020P only)

Image No.dwg20252
KEETON NARROW TAIL1208251.
KEETON BRACKET 10/20 SERIES1290012.
KEETON GUARD129BXT8273.
RHSNB 3/8-16X2 GR5802-411C4.
NUT HEX 3/8-16 PLT803-014C5.
WASHER LOCK SPRING 3/8 PLT804-013C6.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 97 - 196-286P

Table of Contents Part Number Index

25 Series Keeton Seed Firmer (Option)

(Applies to 3N-4025P only)

21855

196-286P - 98 - 04/10/13

Table of Contents Part Number Index

25 Series Keeton Seed Firmer (Option)

(Applies to 3N-4025P only)

Image No.dwg21855
KEETON NARROW TAIL1208251.
BRACKET FOR 890-840C REV A&B129BXT8222.
RHSNB 3/8-16X1 3/4 GR5802-252C3.
NUT HEX 3/8-16 PLT803-014C4.
WASHER LOCK SPRING 3/8 PLT804-013C5.
NUT HEX WHIZ 5/16-18 PLT803-043C6.
HHCS 5/16-18X2 1/2 GR5802-172C7.

Openers

RevisionCommentsPart DescriptionPart No.Ref.

04/10/13 - 99 - 196-286P

Table of Contents Part Number Index

Air Design Scraper (Option)

(Applies to 3N-4010P & 3N-4010HDP, 3N-4015P, 3N-4020P, 3N-4025P only)

20434

196-286P - 100 - 04/10/13