Page 1
Table of Contents Part Number Index
Parts Manual
3N-4010, 3N-4010HDF & 3N-4020
No Till-Drill
Read the Operator's manual entirely.When you see this symbol, the subsequent
instructions and warnings are serious - follow without exception.Your life and the
lives of others depend on it!
20476
Cover illustration may show optional equipment not supplied with standard unit.
© Copyright 2013 Printed 04/10/13 196-359P
Page 2
Table of Contents Part Number Index
Table of Contents
Section 1: Introduction.................................................6
Using This Manual...............................................................6
Manual Replacement Information.......................................6
Manual Revisions................................................................6
Touch-up Paint....................................................................6
Hardware Legend................................................................7
Replacement Hardware......................................................7
Serial Numbers...................................................................7
Part Number Service Coding..............................................7
Tongue and Frame.........................................................8
Hitch To Tongue...................................................................8
Tongue To Wings...............................................................10
Wing To Center Frame......................................................12
Rockshaft.....................................................................15
Rockshaft..........................................................................16
Rockshaft To Frame..........................................................18
Rear Axle Assembly..........................................................20
Gauge Wheel....................................................................24
Gauge Wheel Striker Plate................................................28
Box To Frame...............................................................30
Box To Frame....................................................................30
Box Components...............................................................32
Seed Level Indicator..........................................................34
Walkboards And Steps......................................................36
Drive.............................................................................38
Center Section Drive.........................................................38
Wing Drive.........................................................................40
Veris Drive Components...................................................42
Veris Drive Controller........................................................44
Metering System..........................................................46
Seed Rate Adjustment Handle (118-881S).......................46
Feeder Cup Channel (Center 7.5")...................................48
15 ft Feeder Cup Channel (LH 7.5")..................................50
Feeder Cup Channel (RH 7.5").........................................52
Feeder Cup Channel (LH 10")...........................................54
Feeder Cup Channel (Center 10")....................................56
Feeder Cup Channel (RH 10")..........................................58
Loop Shaft Monitor (2 Channel 116-282A) (3 Channel
116-283A)...................................................................60
Openers........................................................................62
10 Series Opener Arms & Mounts....................................62
10 Series Opener Body.....................................................64
HD10 Series Opener Arms & Mounts...............................66
HD10 Series Opener Body................................................68
HD10 Series Keeton Seed Firmer (Option).......................70
HD10 Series Seed-Lok (Option).......................................72
20 Series Opener Arms & Mounts....................................74
20 Series Opener Body.....................................................76
Keeton Seed Firmer (Option)............................................78
Air Design Scraper (Option)..............................................80
Side Wheel Scraper (Option)............................................82
10 & 20 Series Seed-Lok (Option)....................................84
Coulter...............................................................................86
Grease Bank.....................................................................88
Coulter Tine (Option).........................................................90
Press Wheels...............................................................92
2" x 13" Single Press Wheel..............................................92
3" x 13" Single Press Wheel..............................................94
1" x 12" Double "V" Press Wheel (Part 1).........................96
1" x 12" Double "V" Press Wheel Short.............................98
1" x 12" Double "V" Press Wheel Long...........................100
1" x 10" Double "V" Press Wheel....................................102
1 1/4" x 13 1/2" Double Press Wheel..............................104
1 1/4" x 13" Double Press Wheel....................................106
2" x 12 1/2" Double Press Wheel (Part 1).......................108
2" x 12 1/2" Double Press Wheel (Part 2).......................110
1" x 12" Double "V" Press Wheel (Part 2).......................112
HD10 1 1/4" x 13 1/2" Double Press Wheel....................114
HD10 1" x 12" Double "V" Press Wheel..........................116
HD10 2" x 13" Single Press Wheel.................................118
HD10 3" x 13" Single Press Wheel.................................120
Hydraulics..................................................................122
Lift And Fold Hydraulics..................................................122
Rear Axle Hydraulics.......................................................124
Lock Cylinder Hydraulics.................................................126
Hydraulic Cylinder (810-500C 5x20x2 Rod)....................128
Hydraulic Cylinder (810-499C 5x24x2 Rod)....................130
Hydraulic Cylinder (810-498C 4.5x16x1.5 Rod)..............132
Hydraulic Cylinder (810-497C 4.75x16x1.5 Rod)............134
Hydraulic Cylinder (810-496C 5x16x1.5 Rod).................136
Hydraulic Cylinder (810-201C 1.5x2.5x.75 Rod).............138
Stroke Control Valve (810-503C).....................................140
Double Selector Valve (810-274C)..................................142
Decals.........................................................................144
Decals.............................................................................144
Monitor.......................................................................146
Point Row........................................................................146
Marker.........................................................................148
Marker Arm.....................................................................148
Marker Disk And Hub (113-790S)...................................150
LH Marker Hydraulics......................................................152
Dual Marker Hydraulics...................................................154
Hydraulic Cylinder (810-423C 3 x 24 x 1.5 Rod).............156
Sequence Valve (810-422C)...........................................158
Weight Bracket..........................................................160
Weight Bracket (Option)..................................................160
© Copyright 2013 All rights reserved Printed 04/10/13
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from
the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes
the state of this product at the time of its publication, and may not reflect the product in the future.
The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains
All other brands and product names are trademarks or registered trademarks of their respective holders.
196-359P - 2 - 04/10/13
Great Plains Manufacturing, Incorporated Trademarks
Printed in the United States of America.
Page 3
Table of Contents Part Number Index
Table of Contents (continued)
Part Number Index................................................162
04/10/13 - 3 - 196-359P
Page 4
Table of Contents Part Number Index
Alphabetized Table of Contents
Selected Models
1
1 1/4" x 13 1/2" Double Press Wheel..............................104
1 1/4" x 13" Double Press Wheel....................................106
1" x 10" Double "V" Press Wheel....................................102
1" x 12" Double "V" Press Wheel (Part 1).........................96
1" x 12" Double "V" Press Wheel (Part 2).......................112
1" x 12" Double "V" Press Wheel Long...........................100
1" x 12" Double "V" Press Wheel Short.............................98
10 & 20 Series Seed-Lok (Option)....................................84
10 Series Opener Arms & Mounts....................................62
10 Series Opener Body.....................................................64
15 ft Feeder Cup Channel (LH 7.5")..................................50
2
2" x 12 1/2" Double Press Wheel (Part 1).......................108
2" x 12 1/2" Double Press Wheel (Part 2).......................110
2" x 13" Single Press Wheel..............................................92
20 Series Opener Arms & Mounts....................................74
20 Series Opener Body.....................................................76
3
3" x 13" Single Press Wheel..............................................94
A
Air Design Scraper (Option)..............................................80
B
Box Components...............................................................32
Box To Frame....................................................................30
HD10 1" x 12" Double "V" Press Wheel..........................116
HD10 2" x 13" Single Press Wheel.................................118
HD10 3" x 13" Single Press Wheel.................................120
HD10 Series Keeton Seed Firmer (Option).......................70
HD10 Series Opener Arms & Mounts...............................66
HD10 Series Opener Body................................................68
HD10 Series Seed-Lok (Option).......................................72
Hitch To Tongue...................................................................8
Hydraulic Cylinder (810-201C 1.5x2.5x.75 Rod).............138
Hydraulic Cylinder (810-423C 3 x 24 x 1.5 Rod).............156
Hydraulic Cylinder (810-496C 5x16x1.5 Rod).................136
Hydraulic Cylinder (810-497C 4.75x16x1.5 Rod)............134
Hydraulic Cylinder (810-498C 4.5x16x1.5 Rod)..............132
Hydraulic Cylinder (810-499C 5x24x2 Rod)....................130
Hydraulic Cylinder (810-500C 5x20x2 Rod)....................128
K
Keeton Seed Firmer (Option)............................................78
L
LH Marker Hydraulics......................................................152
Lift And Fold Hydraulics..................................................122
Lock Cylinder Hydraulics.................................................126
Loop Shaft Monitor (2 Channel 116-282A) (3 Channel
116-283A)...................................................................60
M
Marker Arm.....................................................................148
Marker Disk And Hub (113-790S)...................................150
P
Point Row........................................................................146
C
Center Section Drive.........................................................38
Coulter...............................................................................86
Coulter Tine (Option).........................................................90
D
Decals.............................................................................144
Double Selector Valve (810-274C)..................................142
Dual Marker Hydraulics...................................................154
F
Feeder Cup Channel (Center 10")....................................56
Feeder Cup Channel (Center 7.5")...................................48
Feeder Cup Channel (LH 10")...........................................54
Feeder Cup Channel (RH 10")..........................................58
Feeder Cup Channel (RH 7.5").........................................52
G
Gauge Wheel....................................................................24
Gauge Wheel Striker Plate................................................28
Grease Bank.....................................................................88
H
HD10 1 1/4" x 13 1/2" Double Press Wheel....................114
196-359P - 4 - 04/10/13
Rear Axle Assembly..........................................................20
Rear Axle Hydraulics.......................................................124
Rockshaft..........................................................................16
Rockshaft To Frame..........................................................18
Seed Level Indicator..........................................................34
Seed Rate Adjustment Handle (118-881S).......................46
Sequence Valve (810-422C)...........................................158
Side Wheel Scraper (Option)............................................82
Stroke Control Valve (810-503C).....................................140
Tongue To Wings...............................................................10
Veris Drive Components...................................................42
Veris Drive Controller........................................................44
Walkboards And Steps......................................................36
Weight Bracket (Option)..................................................160
Wing Drive.........................................................................40
R
S
T
V
W
Page 5
Table of Contents Part Number Index
Alphabetized Table of Contents (continued)
Wing To Center Frame.................................................12
04/10/13 - 5 - 196-359P
Page 6
Table of Contents Part Number Index
196-359P - 6 - 04/10/13
Page 7
Table of Contents Part Number Index
04/10/13 - 7 - 196-359P
Page 8
Table of Contents Part Number Index
Hitch To Tongue
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20279
196-359P - 8 - 04/10/13
Page 9
Table of Contents Part Number Index
Hitch To Tongue
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20279
SCREW JACK 5000# 15-30890-246C3.
HHCS 1 1/4-7X10 GR5 SPTHD802-543C5.
NUT HEX 1 1/4-7 NYLON INSERT803-081C6.
SAFETY CHAIN WASHER194-070D7.
HHCS 1 1/4-7X11 GR5 SPTHD802-317C8.
SAFETY CHAIN 40000 LB890-398C9.
SINGLE HITCH STRAP-LARGE170-033H10.
RPBY 196-136H170-058H11.
WASHER LOCK 1 1/4 SPRING PLT804-030C12.
NUT HEX 1 1/4-7 PLT803-034C13.
SINGLE HITCH STRAP-SMALL170-034H14.
U-BOLT 5/8-11 X 6 1/32 X 7 3/4806-039C15.
TONGUE SPACERSKID BLOCK817-520C16.
SLIDER BLOCK ADJUST SHIM196-842D17.
NUT HEX FLANGE 5/8-11 PLT803-196C18.
HOSE POST BASE, 40P196-370H19.
PIN COTTER3/16 X 1805-069C20.
WASHER FLAT 1 1/4 USS PLT804-035C21.
SWIVEL HOSE POST196-166H22.
Tongue and Frame
RevisionCommentsPart DescriptionPart No.Ref.
April 05+40P TONGUELH PULLBAR WLDMT196-419H1.
March 05-40P TONGUELH PULLBAR WLDMT196-295H1.
April 05+40P TONGUERH PULLBAR WLDMT196-417H2.
March 05-40P TONGUERH PULLBAR WLDMT196-296H2.
April 05+HITCH PIVOT MOUNT WLDMT196-420H4.
March 05-HITCH PIVOT MOUNT WLDMT196-345H4.
04/10/13 - 9 - 196-359P
Page 10
Table of Contents Part Number Index
Tongue To Wings
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20284
196-359P - 10 - 04/10/13
Page 11
Table of Contents Part Number Index
Tongue To Wings
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20284
HHCS 1 1/4-7X6 1/2 GR5 PLT802-717C1.
NUT HEX 1 1/4-7 NYLON INSERT803-081C2.
U-BOLT 5/8-11 X 6 1/32 X 7 3/4806-039C3.
SLIDER BLOCK ADJUST SHIM196-842D4.
OUTSIDE TONGUESKID BLOCK817-542C5.
NUT HEX FLANGE 5/8-11 PLT803-196C6.
HYD HOSE CLAMP BRACKET502-068D7.
WASHER LOCK SPRING 5/16 PLT804-009C8.
HOSE CLIP 13/16 ID800-064C10.
3N-40 TONGUEBLOCK SUPT BAR196-853D11.
HHCS 5/8-11X1 3/4 GR5802-053C12.
Tongue and Frame
RevisionCommentsPart DescriptionPart No.Ref.
Shown.HHCS 5/16-18X1 1/4 GR5802-010C9.
Used on clamp with larger hoses.HFSS 5/16-18X1 3/4 GR5802-094C9.
04/10/13 - 11 - 196-359P
Page 12
Table of Contents Part Number Index
Wing To Center Frame
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20285
196-359P - 12 - 04/10/13
Page 13
Table of Contents Part Number Index
Wing To Center Frame
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20285
NUT HEX SLOTTED 1 1/4 - 7803-079C1.
WASHER FLAT 1 1/4 USS PLT804-035C2.
PIVOTPIN RETAINER WASHER196-774D3.
40P TOOLBARPIVOT PIN196-652D4.
NUT HEX 1-8 PLT803-031C6.
WASHER LOCK SPRING 1 PLT804-027C7.
HHCS 1-8X4 GR5802-073C8.
FOLD CYLINDER BASE LUG WLDMNT196-344H9.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C10.
40P RH TOOLBAR WELDMENT196-350H11.
BUSHING 4.0X3.5X3.0 LONG SPLIT890-800C12.
ADAPTORNUT 3/4-16 X 5/8-11196-149D13.
NUT HEX JAM 3/4-16 UNF PLT803-235C14.
CYL 1.5X2.5X.75 ROD (TIE ROD)810-201C15.
HHCS 5/8-11X7 1/2 GR5802-146C16.
LOCK ARM WELDMENT196-048H17.
PIN COTTER1/8 X 1 1/4 PLT805-109C18.
WASHER FLAT 1 1/4 HOSE GUARD196-875D19.
WASHER FLAT 5/8 SAE PLT804-021C20.
SPRING COMP .906OD X 9 X .105W807-128C21.
PIN CLEVIS 5/8 X 2.77 USALBE805-028C22.
PIN CLEVIS 1/2 X 2 1/2 PLT805-192C23.
WASHER FLAT 1/2 SAE PLT804-016C24.
TRANSPORT LOCK LATCHBAR196-766D25.
PIN COTTER5/32 X 1 PLT805-019C26.
40P CENTER FRAME WELDMENT196-351H27.
PIN COTTER5/16 X 2 1/2805-085C28.
HHCS 3/4-10X7 GR5802-095C29.
NUT LOCK 3/4-10 PLT803-026C30.
GREASE ZERK STRAIGHT 1/4-28800-001C31.
SPACER WASHER196-775D32.
FOLD CYL ADJUSTMENT SHIM196-777D33.
PIN COTTER1/4 X 2 1/2 PLT805-105C34.
WASHER FLAT 1 USS PLT804-028C35.
TOOLBAR LOCK BAR196-896D36.
NUT HEX 3/4-10 PLT803-027C37.
NUT HEX 5/16-18 PLT803-008C38.
WASHER LOCK SPRING 5/16 PLT804-009C39.
HHCS 5/16-18X1 GR5802-159C40.
HHCS 1 1/4-7X4 1/2 GR5802-273C41.
NUT HEX 1 1/4-7 PLT803-034C42.
GREASE ZERK 1/4-28 X 90-DEG800-073C43.
HOSE GUARDCAP196-050H44.
SPRING LEVER807-007C45.
TOOLB LOCK ARM WELDM196-377H46.
MIDWAYROD CLEVIS 3/4-16 UNF810-491C47.
NUT LOCK 3/8-16 PLT803-013C48.
WASHER FLAT 3/4 USS PLT804-024C49.
HHCS 3/8-16X2 1/4 GR5802-382C50.
PIN CLEVIS 5/8 X 2 1/2 PLT805-141C51.
RPBY 196-409H196-393H52.
CYL PIN NR 1.25X3.63USBX3.13CH196-392H53.
NUT HEX JAM 3/4-10 PLT803-048C54.
U-BOLT 3/8-16X 6.13 X 6.25 RND806-194C55.
Tongue and Frame
RevisionCommentsPart DescriptionPart No.Ref.
Includes pinsCYL REP 5X24X2 ROD (TIE)810-499C5.
Shown40P LH TOOLBAR WELDMENT196-349H11.
Referto "Hydraulic Cylinder(810-496C
5x16x1.5 Rod)"
04/10/13 - 13 - 196-359P
Page 14
Table of Contents Part Number Index
Wing To Center Frame (continued)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
NUT HEX 3/8-16 PLT803-014C56.
WASHER LOCK SPRING 3/8 PLT804-013C57.
40P LH WING FRAME WELDMENT196-338H58.
40P RH WING FRAME WELDMENT196-339H58.
RevisionCommentsPart DescriptionPart No.Ref.
196-359P - 14 - 04/10/13
Page 15
Table of Contents Part Number Index
Wing To Center Frame (continued)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
This Page Intentionally Left Blank
Tongue and Frame
04/10/13 - 15 - 196-359P
Page 16
Table of Contents Part Number Index
Rockshaft
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20280
196-359P - 16 - 04/10/13
Page 17
Table of Contents Part Number Index
Rockshaft
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20280
40P ROCKSHAFT WELDMENT196-319H1.
CYLINDER LOCK CHANNEL 1 1/2X16196-289H2.
SPINDLE SGL 2.73X15.97815-099C3.
HUB STUD 5/8-18X2 1/2 GR5802-182C4.
8-BOLT WHEEL HUB MACH.200-006D5.
GREASE CAPP5020016.
NUT LUG 5/8-18 X 90 DEG PLT803-219C7.
HHCS 3/4-10X5 GR5802-069C10.
NUT HEX 3/4-10 PLTNYLOCK803-025C11.
HUB 8 BOLT 5790# W/CUPS&STUDS815-101C12.
BRG CONE 2.00IDX1.18WD #3780822-036C13.
BRG CONE 1.31IDX1.01WD #2790822-038C14.
TIRE SKID ST 395/55B16.5 NHS814-206C16.
RIM 16.5X12, 8 BLT6 PILT 8 BC814-208C17.
VALVE STEM METAL TR-575 TUBLES814-210C18.
BRG CUP 3.67ODX.93WD #3720822-037C19.
BRG CUP 3.00ODX.75WD #2720822-039C20.
7/8 SPINDLE WASHER, HARDENED181-064D21.
NUT HEX SLOTTED 7/8-14 PLT803-029C22.
PIN COTTER3/16 X 1 1/4 PLT805-016C23.
8-BOLT HUB SEAL816-019C24.
GREASE ZERK STRAIGHT 1/4-28800-001C25.
Rockshaft
RevisionCommentsPart DescriptionPart No.Ref.
Includes: 16-18RH TIRE/RIM 395/55B16.5 SKID 8196-272K8.
Includes: 16-18LH TIRE/RIM 395/55B16.5 SKID 8196-273K9.
Formerly 805-152CPIN 3/8 X 3 USABLE LW/PIN805-001C15.
Includes: 3-6, 12-14, & 14-19HUB & SPINDLE ASY 8 BOLT 5790#815-103C26.
04/10/13 - 17 - 196-359P
Page 18
Table of Contents Part Number Index
Rockshaft To Frame
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20281
196-359P - 18 - 04/10/13
Page 19
Table of Contents Part Number Index
Rockshaft To Frame
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20281
DEPTH STOPTUBE BRACKET196-907D1.
STROKE CONTROLPADDLE WLDMT196-298H2.
DEPTH STOPSLIDE TUBE196-905D3.
KNOB 1/2-13 MALE THD 2 3/8OD817-455C4.
U-BOLT 5/8-11 X 4 1/32 X 3 3/8806-019C5.
DEPTH VALVE MOUNT196-381H6.
NUT HEX 5/8-11 PLT803-021C7.
WASHER LOCK SPRING 5/8 PLT804-022C8.
VALVE, STROKE CTRL 35 GPM -12810-503C9.
DEPTH STOPCURVED LINK PLATE196-904D10.
40P ROCKSHAFT PIN WELDMENT196-288H11.
PIN ROLL 3/8 X 2 PLT805-249C12.
BUSHING 1 1/2 X 1 1/4 X 1 1/2890-122C13.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C14.
CYL REP 5X16X1.5 ROD (TIE)810-496C15.
RHSNB 1/2-13X5 GR5802-463C16.
NUT HEX 5/16-18 PLT803-008C17.
GREASE ZERK STRAIGHT 1/4-28800-001C18.
U-BOLT 1/2-13 X 6 1/32 X 7 1/4806-060C19.
NUT HEX 1/2-13 PLT803-020C20.
WASHER LOCK SPRING 1/2 PLT804-015C21.
HEIGHT SWITCH CAM NO CLP 2.25817-476C22.
CLAMP WRM DRV #40 SS (2.06-3)800-144C23.
NUT HEX 10-24 PLT803-001C24.
2SNT IMPLEMENT SWITCH823-198C25.
SCREW PAN HD 1/4-20 X 3/4801-005C26.
HHCS 3/8-16X2 3/4 GR5802-216C27.
TUBE RND CREW 3/4ODX12GX3.25196-906D28.
CYL PIN NR 1.25X3.09X2.63 W/GR196-409H29.
CYL PIN NR 1.25X3.72USBX3.13CH196-391H30.
WASHER FLAT 1 1/4 USS PLT804-035C31.
PIN COTTER1/4 X 2 1/2 PLT805-105C32.
803-184 FLG TP LK 5/16-18ZNYCR803-177C33.
HHCS 5/16-18X2 GR5802-115C34.
BAR FLT HR 3/16X1 3/4X4.88196-911D35.
WASHER LOCK SPRING 5/16 PLT804-009C36.
Rockshaft
RevisionCommentsPart DescriptionPart No.Ref.
Includes pins and clips Refer to
"Hydraulic Cylinder (810-497C
4.75x16x1.5 Rod)"
04/10/13 - 19 - 196-359P
Page 20
Table of Contents Part Number Index
Rear Axle Assembly
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20282
196-359P - 20 - 04/10/13
Page 21
Table of Contents Part Number Index
Rear Axle Assembly
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20282
40P REAR AXLE WLDMT196-106H1.
HHCS 5/16-18X1 1/4 GR5802-010C2.
WASHER LOCK SPRING 5/16 PLT804-009C3.
HYD HOSE CLAMP BRACKET502-068D4.
NUT HEX 1 1/2-6 PLT803-073C5.
WASHER LOCK 1 1/2 PLT804-197C6.
NUT HEX JAM 1 1/2-6 PLT803-063C7.
EYEBOLT WELDMENT196-293H8.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C9.
CYL REP 4.5X16X1.5 ROD (TIE)810-498C10.
GREASE ZERK STRAIGHT 1/4-28800-001C11.
CYL LOCK CHANNEL 1 1/2X17 3/4196-292H12.
40P TOOLBARPIVOT PIN196-652D14.
HHCS 1-8X18 GR5802-728C15.
PIVOTPIN RETAINER WASHER196-774D16.
WASHER FLAT 1 1/4 USS PLT804-035C17.
NUT HEX SLOTTED 1 1/4 - 7803-079C18.
40P CASTER INNER PIVOT TUBE196-654D19.
WASHER LOCK SPRING 1 PLT804-027C20.
NUT HEX 1-8 PLT803-031C21.
40P CASTER PARALLEL ARM WLDMT196-287H22.
BUSHING 1 7/8X1 5/8X1 1/2 SPLT890-666C23.
WASHER FLAT 1 SAE804-029C24.
HHCS 1/2-13X1 1/4 GR5802-034C25.
WASHER LOCK SPRING 1/2 PLT804-015C26.
NTA CASTER RETAINER CAP161-231D27.
STEEL BUSHING 3 1/4X3IDX3LONG890-193C28.
40P CASTER SUPPORT WLDMT196-329H29.
PIVOTTHRUST WASHER804-102C30.
REAR CASTER SUPT WLDMT196-397H31.
HHCS 3/4-10X5 GR5802-069C33.
NUT HEX 3/4-10 PLTNYLOCK803-025C34.
40P RADARMOUNT WLDMT196-294H37.
CASTER SPRING PLUNGER196-769D38.
SPRING COMP 1.88OD x .362W807-143C39.
CASTER DETENT PIN196-770D40.
HHCS 3/4-10X2 GR5802-064C41.
WASHER LOCK SPRING 3/4 PLT804-023C42.
NUT HEX 3/4-10 PLT803-027C43.
HHCS 3/4-10X6 GR5802-070C44.
NUT LOCK 3/4-10 PLT803-026C45.
PIN COTTER5/16 X 2 1/2805-085C46.
HHCS 3/4-10X4 GR5 FTHD802-067C47.
SPACER WASHER196-775D48.
RPBY 196-409H196-393H49.
CYL PIN NR 1.25X3.63USBX3.13CH196-392H50.
WASHER FLAT 1 USS PLT804-028C51.
PIN COTTER1/4 X 2 1/2 PLT805-105C52.
HHCS 1/4-28X3/8 GR5802-300C53.
NUT HEX JAM 3/4-10 PLT803-048C54.
HHCS 1/2-13X2 GR5802-128C55.
REAR CASTER LOCK PLTHARDENED196-870D56.
Rockshaft
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Hydraulic Cylinder (810-499
5x24x2 Rod)" for breakdown
Formerly 805-152CPIN 3/8 X 3 USABLE LW/PIN805-001C13.
Refer to "Rockshaft"LH TIRE/RIM 395/55B16.5 SKID 8196-273K32.
Refer to "Rockshaft"HUB & SPINDLE ASY 8 BOLT 5790#815-103C35.
Refer to "Rockshaft"RH TIRE/RIM 395/55B16.5 SKID 8196-272K36.
04/10/13 - 21 - 196-359P
Page 22
Table of Contents Part Number Index
Rear Axle Assembly (continued)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
NUT HEX 1/2-13 PLT803-020C57.
BUSHING 4.0X3.5X3.0 LONG SPLIT890-800C59.
RevisionCommentsPart DescriptionPart No.Ref.
Includes: 26, 31, 40, & 55-57REAR CASTER & HARD LCK PLTKIT196-394L58.
196-359P - 22 - 04/10/13
Page 23
Table of Contents Part Number Index
Rear Axle Assembly (continued)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
This Page Intentionally Left Blank
Rockshaft
04/10/13 - 23 - 196-359P
Page 24
Table of Contents Part Number Index
Gauge Wheel
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20283
196-359P - 24 - 04/10/13
Page 25
Table of Contents Part Number Index
Gauge Wheel
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20283
40P LOCK CASTER SUPPORT WLDMT196-325H1.
CASTER LOCK LUG196-767D2.
STEEL BUSHING 3 1/4X3IDX3LONG890-193C4.
PIVOTTHRUST WASHER804-102C5.
CASTER LOCK RAMP196-768D7.
CASTER DETENT PIN196-770D8.
HHCS 1-8X18 GR5802-728C9.
WASHER FLAT 1 SAE804-029C10.
CASTER SPRING PLUNGER196-769D11.
HHCS 3/4-10X4 GR5 FTHD802-067C12.
WASHER FLAT 5/8 SAE PLT804-021C13.
PIN CLEVIS 5/8 X 3 1/2805-334C14.
PIN COTTER1/8 X 1 1/4 PLT805-109C15.
WASHER LOCK SPRING 1 PLT804-027C16.
NUT HEX 1-8 PLT803-031C17.
HHCS 1/2-13X1 1/4 GR5802-034C18.
WASHER LOCK SPRING 1/2 PLT804-015C19.
NTA CASTER RETAINER CAP161-231D20.
40P CASTER INNER PIVOT TUBE196-654D21.
BUSHING 1 7/8X1 5/8X1 1/2 SPLT890-666C22.
40P CASTER PARALLEL ARM WLDMT196-287H23.
BUSHING SPINDLE 1 1/2X1 1/4X1890-011C24.
EYEBOLT WELDMENT196-293H25.
NUT HEX JAM 1 1/2-6 PLT803-063C26.
WASHER LOCK 1 1/2 PLT804-197C27.
NUT HEX 1 1/2-6 PLT803-073C28.
40P GW SWIVEL PIN196-653D29.
PIVOTPIN RETAINER WASHER196-774D30.
WASHER FLAT 1 1/4 USS PLT804-035C31.
NUT HEX SLOTTED 1 1/4 - 7803-079C32.
HHCS 1/2-13X2 GR5802-128C34.
NUT HEX 1/2-13 PLT803-020C36.
CYL REP 4.75X16X1.5 ROD (TIE)810-497C37.
HHCS 1-8X18 GR5802-728C38.
GREASE ZERK STRAIGHT 1/4-28800-001C40.
NUT LUG 5/8-18 X 90 DEG PLT803-219C41.
RPBY 196-409H196-393H42.
CYL PIN NR 1.25X3.63USBX3.13CH196-392H43.
PIN COTTER1/4 X 2 1/2 PLT805-105C44.
CYL 1.5X2.5X.75 ROD (TIE ROD)810-201C46.
NUT HEX FLANGE LOCK 3/4-10 PLT803-181C47.
MIDWAYROD CLEVIS 3/4-16 UNF810-491C48.
SPRING COMP 1.88OD X .362W807-143C50.
Rockshaft
RevisionCommentsPart DescriptionPart No.Ref.
2nd rev.CASTER LOCK ARM EXTEND196-376H3.
1st rev.CASTER LOCK ARM WELDMENT196-343H3.
(Shown) Left wingLH LOCKING CASTER SUPT WLDMT196-398H6.
Right wingRH LOCKING CASTER SUPT WLDMT196-399H6.
(Shown) Left Wing40P CASTER SWIVEL MOUNT LH196-333H33.
Right Wing40P CASTER SWIVEL MOUNT RH196-328H33.
(Shown) Left WingCASTER LOCK PLT LH HARDENED196-872D35.
Right WingCASTER LOCK PLT RH HARDENED196-873D35.
Referto "Hydraulic Cylinder(810-498C
4.5x16x1.5 Rod)"
Includes 6, 8, 19, 34, 35, 36FRNT CASTR LH&HARD LCK PLT KIT196-395L39.
Includes 6, 8, 19, 34, 35, 36FRNT CASTR RH&HARD LCK PLT KIT196-396L39.
Refer to "Rockshaft"RH TIRE/RIM 395/55B16.5 SKID 8196-272K45.
Referto "Hydraulic Cylinder(810-496C
5x16x1.5 Rod)"
Refer to "Rockshaft"HUB & SPINDLE ASY 8 BOLT 5790#815-103C49.
04/10/13 - 25 - 196-359P
Page 26
Table of Contents Part Number Index
Gauge Wheel (continued)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
SPRING COMP 1.4OD .162W 3LG807-212C51.
HHCS 1/4-28X3/8 GR5802-300C52.
HHCS 3/4-10X5 GR5802-069C53.
NUT HEX 3/4-10 PLTNYLOCK803-025C54.
PIN COTTER5/16 X 2 1/2805-085C56.
PIN 3/4 X 4 13/32 USEABLE805-230C57.
WASHER FLAT 1 USS PLT804-028C59.
HHCS 3/4-10X6 GR5802-070C60.
NUT LOCK 3/4-10 PLT803-026C61.
NUT HEX JAM 3/4-10 PLT803-048C62.
HHCS 1-8X3 GR5802-368C63.
NUT HEX JAM 1-8 PLT803-030C64.
HOSE LOOP 2 5/8 WITH TAB160-018H65.
NUT HEX 5/8-11 PLT803-021C66.
WASHER LOCK SPRING 5/8 PLT804-022C67.
HHCS 5/8-11X2 GR5802-055C68.
HHCS 5/8-11X5 GR5802-062C69.
NUT HEX NYLOCK 5/8-11 PLT803-148C70.
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Rockshaft"LH TIRE/RIM 395/55B16.5 SKID 8196-273K55.
Refer to "Lock Cylinder Hydraulics"CYL REP 5X20X2 ROD (TIE)810-500C58.
196-359P - 26 - 04/10/13
Page 27
Table of Contents Part Number Index
Gauge Wheel (continued)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
This Page Intentionally Left Blank
Rockshaft
04/10/13 - 27 - 196-359P
Page 28
Table of Contents Part Number Index
Gauge Wheel Striker Plate
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20364
196-359P - 28 - 04/10/13
Page 29
Table of Contents Part Number Index
Gauge Wheel Striker Plate
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20364
U-BOLT 5/8-11 X 4 1/32 X 3 3/8806-019C1.
TONGUE SPACERSHIM196-782D2.
WING RUBBLOCK196-800D3.
NUT HEX FLANGE LOCK 5/8-11 PLT803-263C4.
40P CASTER SWIVEL MOUNT RH196-328H5.
TUBE RND 1 1/4ODX3/16X1.05196-891D6.
GW SWIVEL LOCK LUG196-856D7.
HHCS 3/8-16X2 GR5802-143C8.
HHCS 7/8-9X1 1/2 GR5802-622C9.
PIN SPIROL 1/2X2 1/2 PLAIN805-037C10.
GW SWIVEL LOCK SPREADER LINK196-859D11.
WASHER LOCK SPRING 7/8 PLT804-037C12.
HHCS 7/8-9X2 3/4 GR8802-275C13.
NUT LOCK 5/8-11 PLT803-024C14.
GW SWIVEL LOCK SLOT LINK196-858D15.
WASHER FLAT 5/8 USS PLT804-019C16.
HHCS 5/8-11X2 3/4 GR5802-281C17.
SPRING EXT 1 7/8ODX8 3/8X.25W807-113C18.
GW SWIVEL LOCK CYL ROD PLT196-857D19.
NUT HEX JAM 3/4-16 UNF PLT803-235C20.
CYL 1.5X2.5X.75 ROD (TIE ROD)810-201C21.
HOSE LOOP 2 5/8 WITH TAB160-018H22.
HHCS 5/8-11X1 1/4 GR5802-050C23.
WASHER LOCK SPRING 5/8 PLT804-022C24.
NUT HEX 5/8-11 PLT803-021C25.
HHCS 3/8-16X1 GR5802-017C26.
WASHER LOCK SPRING 3/8 PLT804-013C27.
WASHER FLAT 3/8 USS PLT804-011C28.
SPRING ANCHOR ANGLE196-889D29.
NUT HEX 3/8-16 PLT803-014C30.
SLEEVE IDLER PIVOT402-037D31.
BOX MOUNTING TUBE123-320D32.
CLOSED EYE BOLT 3/8-16X4 1/2802-674C33.
NUT HEX 7/8-9 PLT803-049C34.
HHCS 7/8-9X5 GR5802-546C35.
Rockshaft
RevisionCommentsPart DescriptionPart No.Ref.
Shown40P CASTER SWIVEL MOUNT LH196-333H5.
Referto "Hydraulic Cylinder(810-496C
5x16x1.5 Rod)"
04/10/13 - 29 - 196-359P
Page 30
Table of Contents Part Number Index
Box To Frame
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20454
196-359P - 30 - 04/10/13
Page 31
Table of Contents Part Number Index
Box To Frame
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20454
40P RH WING FRAME WELDMENT196-339H1.
3N-40 SEED BOX WLDMNT197-168H2.
SEED BOX PARTITION118-402D3.
NUT HEX FLANGE 5/16-18 PLT803-199C4.
HFS 5/16-18X3/4 GR5802-387C5.
HANDLE119-190D6.
HFSS 1/2-13X1 1/2 GR5802-203C7.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C8.
HHCS 1/2-13X1 1/4 GR5802-034C9.
WASHER LOCK SPRING 1/2 PLT804-015C10.
NUT HEX 1/2-13 PLT803-020C11.
BOX PARTITION UPPER PAD118-052H12.
3N-40P BOX GUSSET RH197-290D13.
3N-40P BOX GUSSET LH197-289D14.
HFSS 1/2-13X1 1/4 GR8802-083C15.
HFSS 1/4-20X5/8 GR5802-196C16.
NUT HEX LOCK 1/4-20 FLG803-088C17.
Box To Frame
RevisionCommentsPart DescriptionPart No.Ref.
Shown40P LH WING FRAME WELDMENT196-338H1.
04/10/13 - 31 - 196-359P
Page 32
Table of Contents Part Number Index
Box Components
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20289
196-359P - 32 - 04/10/13
Page 33
Table of Contents Part Number Index
Box Components
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20289
40P SEED LID 144 WLDMT197-166H1.
3N-40 SEED BOX WLDMNT197-168H2.
HFS 5/16-18X3/4 GR5802-387C3.
NUT HEX FLANGE 5/16-18 PLT803-199C4.
BALL STUD 10MM X 5/16-18 X 1/2800-121C5.
12-20 X 90 LB GAS SPRING890-221C6.
NUT LOCK 5/16-18 PLT803-011C7.
LATCH CASTING MACHINED119-153D8.
SPRING .540 O.D.X 1 1/4 X.054W807-106C9.
LID HANDLE119-154D10.
WASHER FLAT 5/16 SAE PLT804-036C11.
HHCS 5/16-18X1 1/4 NYL802-425C12.
NUT FLANGE LOCK 3/8-16 PLT803-209C13.
LID HINGE PIVOT313-186D14.
LID HINGE BASE PLATE313-176D15.
HFS 3/8-16X1 GR5802-388C16.
RHSNB 3/8-16X2 GR5802-411C17.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C18.
HHCS 1/4-20X3/4 GR5802-004C19.
MINI END WHEEL PRESS WHEEL817-042C20.
NUT HEX FLNG T-LOCK 1/4-20 YLW803-293C21.
MANUAL PAK 1'" W/ GASKET817-516C22.
HFSS 1/2-13X1 1/2 GR5802-203C23.
12' EWNT LIGHT BRACKET150-138D24.
MANUAL PAK MOUNTING PLATE248-251D25.
DUAL AG LIGHTS LH890-311C26.
DUAL AG LIGHTS RH890-312C27.
SCR HEX SELF TAP 1/4-20X1TYPEF801-151C28.
AG LIGHT WIRING HARNESS-28'890-313C29.
LIGHT HARNESS, 10' WISHBONE890-390C30.
CABLE TIE .19X7.25 1.75D 50LB800-112C31.
CABLE TIE MOUNT800-148C32.
AG LIGHT HARNESS, EXT-15'890-600C33.
Box To Frame
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 33 - 196-359P
Page 34
Table of Contents Part Number Index
Seed Level Indicator
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
19187
196-359P - 34 - 04/10/13
Page 35
Table of Contents Part Number Index
Seed Level Indicator
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg19187
SEED LEVEL ARM, 6 3/4R. TAB118-474H1.
FOAM FLOAT197-089D2.
SEED LEVEL CHAIN BRACKET197-091D3.
FOAM FLOAT WASHER197-096D4.
RIVET POP 1/8X.265LG FLG800-101C5.
HFS 10-24 X 1 1/8 PLTD801-096C6.
SCR HEX HD SHT MET #8 X 1/2801-154C7.
NUT HEX 10-24 PLT803-001C8.
NUT HEX NYLOCK 1/4-20803-255C9.
WASHER INTERNAL STAR #10 PLT804-004C10.
WASHER FLAT 1/4 USS PLT804-075C11.
PIN COTTER1/8 X 3/4805-067C12.
SEED LEVEL BUSHING817-086C13.
SEED LEVEL ARM MOUNT817-202C14.
SEED LEVEL INDICATOR817-350C15.
CABLE 3/64 X 11 5/8 W/ EYELETS890-305C16.
Box To Frame
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 35 - 196-359P
Page 36
Table of Contents Part Number Index
Walkboards And Steps
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20290
196-359P - 36 - 04/10/13
Page 37
Table of Contents Part Number Index
Walkboards And Steps
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20290
40P WALKBOARD WLDMT196-297H1.
40P RH WING FRAME WELDMENT196-339H2.
NUT LOCK 1/2-13 PLT803-019C3.
HHCS 1/2-13X1 1/4 GR5802-034C4.
PIN CLEVIS 1/2 X 1 3/4805-127C5.
PIN HAIR COTTER .120 PLT805-143C6.
HHCS 3/8-16X1 1/4 GR5802-079C7.
WASHER FLAT 3/8 SAE PLT804-012C8.
NUT LOCK 3/8-16 NYLON INSERT803-078C9.
40P LADDER WLDMT196-299H10.
OPENER HANDLE HOLDER119-211D11.
PIN HAIR COTTER .148 WIRE805-032C12.
SPRING ADJ HANDLE WELDMENT198-810H13.
NUT FLANGE LOCK 3/8-16 PLT803-209C14.
HFS 3/8-16X1 GR5802-388C15.
U-BOLT 3/8-16 X 2 1/32 X 3806-166C16.
WASHER LOCK SPRING 3/8 PLT804-013C17.
NUT HEX 3/8-16 PLT803-014C18.
WALKBOARDFILLER STRIP196-886D19.
WALKBOARDFILLER CHANNEL196-887D20.
NUT HEX 5/16-18 PLT803-008C21.
WASHER LOCK SPRING 5/16 PLT804-009C22.
HHCS 5/16-18X1 GR5802-159C23.
40P WALKBOARD WLDMT196-297H24.
Box To Frame
RevisionCommentsPart DescriptionPart No.Ref.
Shown40P LH WING FRAME WELDMENT196-338H2.
04/10/13 - 37 - 196-359P
Page 38
Table of Contents Part Number Index
Center Section Drive
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20455
196-359P - 38 - 04/10/13
Page 39
Table of Contents Part Number Index
Center Section Drive
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20455
VERIS PPC-40 CONTROLLER833-251C1.
COLLAR LOCK 7/8 HEX402-058D2.
SCREW SET 5/16-18 SKT KP X 3/8801-035C3.
LOCK COLLAR, 7/8 HEX W/ SET SC402-025S4.
SPKT 50C36 X 7/8 HEX BORE808-313C5.
SPKT 40B14 X 7/8 HEX BORE808-259C6.
CHAIN RL #40 91 PITCHES136-120D7.
RHSNB 5/16-18X1 GR5802-282C8.
FLANGETTE 52 3-BOLT PLT822-175C9.
BRG INS 7/8HEXX2.04OD SPH822-195C10.
803-184 FLG TP LK 5/16-18ZNYCR803-177C11.
WASHER FLAT 1/2 USS HARD PLT804-113C12.
WASHER LOCK SPRING 1/2 PLT804-015C13.
NUT HEX 1/2-13 PLT803-020C14.
IDLER SPOOL #50 2.38X1.01X.31817-456C15.
TUBE RND 1 OD X 7/32W X 2.13120-306D16.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C17.
SHAFT 7/8 HEX GW PIVOT120-286D18.
U-JOINT DRIVE SHAFT YOKE196-245H19.
SPKT 50A25 CLUTCH METRIC BORE808-357C20.
CHAIN RL #50 92 PITCHES136-200D21.
OGURA CLUTCH823-231C22.
40P CENTER CLUTCH SHAFT196-776D23.
PIN ROLL 1/4 X 1 1/2 LG PLT805-180C24.
SPKT 50C27 X 7/8 HEX BORE808-311C25.
CHAIN RL #50 72 PITCHES136-202D26.
WASHER MACH 1.50 X 1.00 X 18GA804-061C28.
SPKT 50B21 X 1 BORE W/KW, 2 SS808-294C29.
HHCS 1/4-20X5 GR5 PLT802-085C30.
NUT-HEX 1/4-20 PLT803-006C31.
TUBE RND DOM. 1 OD X 7/32WX3.0120-293D32.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C33.
WASHER FLAT 1/2 USS HARD PLT804-113C34.
VERIS DRIVE SUPPORT SPACER196-847D35.
HHCS 5/8-11X2 1/2 GR5802-058C36.
WASHER LOCK SPRING 5/8 PLT804-022C37.
NUT HEX 5/8-11 PLT803-021C38.
TUBE RND DOM. 1 OD X 7/32WX3.0120-293D39.
IDLER 1 PC 2.38X1.01X1.062817-406C40.
3N-40 FD CUP DRIVE IDLER PLT196-850D41.
HHCS 1/2-13X1 1/4 GR5802-034C42.
CLUTCH ROTATION TAB196-866D43.
CLUTCH SPROCKET SPACER196-876D44.
WASHER FLAT 1/4 USS PLT804-075C45.
WASHER LOCK SPRING 1/4 PLT804-006C46.
KEY 1/4 X 3/16 X 3.80839-956C47.
BUSHING 1 1/8 ODX7/8 HEX BORE196-877D48.
HHCS 5/16-18X1 GR5802-159C49.
NUT HEX 5/16-18 PLT803-008C50.
WASHER LOCK SPRING 5/16 PLT804-009C51.
TUBE RND 1 OD X 7/32W X 2.13120-306D52.
CLUTCH OIL SHIELD402-507D53.
BUTTON PLUG 7/8 ROUND HOLE817-813C54.
Drive
RevisionCommentsPart DescriptionPart No.Ref.
Use liquid thead lockerHSHCS M8X1.25X30 GR8.8 PLT802-775C27.
04/10/13 - 39 - 196-359P
Page 40
Table of Contents Part Number Index
Wing Drive
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20456
196-359P - 40 - 04/10/13
Page 41
Table of Contents Part Number Index
Wing Drive
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20456
PIN COTTER1/8 X 3/4805-067C1.
U-JOINT PIN 3/8195-157D2.
U-JOINT NYLATRON CROSS BLOCK817-273C3.
PIN ROLL 1/4 X 1 1/2 LG PLT805-180C4.
RPBY 800-124C800-311C5.
SLIDER SHAFT 7/8 HEX 44.50 LG196-581D6.
SEED HOSE X 45 RIBS816-107C7.
GREASE ZERK STRAIGHT 1/4-28800-001C8.
TELESCOPING DRIVE SHAFT TUBE196-246H9.
40P LH WING FRAME WELDMENT196-338H10.
40P WING CLUTCH STUB SHAFT196-773D11.
SHAFT 7/8 HEX GW PIVOT120-286D12.
WASHER MACH 1.50 X 1.00 X 18GA804-061C13.
RHSNB 5/16-18X1 GR5802-282C14.
FLANGETTE 52 3-BOLT PLT822-175C15.
BRG 7/8HEXX2.05OD SPH822-119C16.
803-184 FLG TP LK 5/16-18ZNYCR803-177C17.
SPKT 50A25 CLUTCH METRIC BORE808-357C19.
OGURA CLUTCH823-231C20.
SCREW SET 5/16-18 SKT KP X 3/8801-035C21.
COLLAR LOCK 7/8 HEX402-058D22.
LOCK COLLAR, 7/8 HEX W/ SET SC402-025S23.
WASHER FLAT 1/2 USS HARD PLT804-113C24.
WASHER LOCK SPRING 1/2 PLT804-015C25.
NUT HEX 1/2-13 PLT803-020C26.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C27.
TUBE RND DOM. 1 OD X 7/32WX3.0120-293D28.
IDLER SPOOL #50 2.38X1.01X.31817-456C29.
SPKT 50C36 X 7/8 HEX BORE808-313C30.
SPKT 40B14 X 7/8 HEX BORE808-259C31.
CHAIN RL #40 99 PITCHES136-126D32.
CHAIN RL #50 83 PITCHES136-201D33.
HHCS 1/4-20X5 GR5 PLT802-085C34.
NUT-HEX 1/4-20 PLT803-006C35.
3N-40 FD CUP DRIVE IDLER PLT196-850D36.
HHCS 1/2-13X1 1/4 GR5802-034C37.
U-JOINT DRIVE SHAFT YOKE196-245H38.
HHCS 1/2-13X4 1/2 GR5 SPTHD802-672C39.
IDLER 1 PC 2.38X1.01X1.062817-406C40.
WASHER FLAT 1/2 USS PLT804-017C41.
WASHER FLAT 1/4 USS PLT804-075C42.
WASHER LOCK SPRING 1/4 PLT804-006C43.
CLUTCH ROTATION TAB196-866D44.
CLUTCH SPROCKET SPACER196-876D45.
BUSHING 1 1/8 ODX7/8 HEX BORE196-877D46.
KEY 1/4 X 3/16 X 3.80839-956C47.
HHCS 5/16-18X1 GR5802-159C48.
WASHER LOCK SPRING 5/16 PLT804-009C49.
NUT HEX 5/16-18 PLT803-008C50.
CLUTCH OIL SHIELD402-507D51.
BUTTON PLUG 7/8 ROUND HOLE817-813C52.
Drive
RevisionCommentsPart DescriptionPart No.Ref.
Use liquid thead lockerHSHCS M8X1.25X30 GR8.8 PLT802-775C18.
04/10/13 - 41 - 196-359P
Page 42
Table of Contents Part Number Index
Veris Drive Components
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20299
196-359P - 42 - 04/10/13
Page 43
Table of Contents Part Number Index
Veris Drive Components
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20299
CONTROLLER MOUNT 40' WELDMENT402-307H1.
MOTORMOUNT 40' WELDMENT402-306H2.
VERIS PROPORTIONAL CARTR 14GPMVER-197983.
VERIS COIL 12V WATERMAN CARTRVER-197994.
VERIS VLV BODY SAE-12-2X SAE-8VER-198005.
VERIS SOLENOID CABLEVER-183756.
VERIS EXT. CONTROLVER-215687.
VERIS FILTER HYD 3000 PSI PALLVER-185748.
VERIS HYD LINE STL .5 OD X.049VER-52119.
VERIS MOTOR HYD 8.8 CIRVER-1985710.
VERIS ENCODER W/ CABLEVER-1838211.
AD 3/4FORB 7/8MORB811-564C12.
RPBY 810-696CVER-1955413.
AD 3/4MJIC 7/8MORB811-192C14.
HH1/2M3K 3/4FJIC 3/4FJIC90X168VER-2539015.
AD 3/4MJIC 1 1/16MORB811-205C16.
VERIS FTG HYD 8MB-8MJ90VER-518417.
VERIS BLT FLG SER8.8M8-1.25X16VER-1854818.
HFSS 1/2-13X1 1/2 GR5802-203C19.
NUT HEX WHIZ 1/2-13803-037C20.
RPBY 802-642CVER-441621.
803-184 FLG TP LK 5/16-18ZNYCR803-177C22.
HFSS 1/4-20X3/4 GR5802-257C23.
NUT HEX LOCK 1/4-20 FLG803-088C24.
VERIS BLT HH1/4-20NCX2.25GR5ZNVER-967925.
VERIS HYD HS 8M3K-8FJX90S-8FJXVER-258426.
VER FLTR ELEMENT PALL 6 MICRONVER-1985627.
AD 3/4MORB 3/4MJIC811-088C28.
EL 3/4MJIC 3/4MORB811-063C29.
DOUBLE SELECTORVALVE 3/4FORB810-274C30.
HH1/2R2 336 3/4MORB 3/4FJIC841-056C31.
TE 9/16MJIC 3/4MORB 9/16MJIC811-249C32.
HH1/4R1 095 9/16FJIC811-230C33.
HH1/4R1 048 9/16FJIC811-781C34.
SELECTOR VALVE MOUNT STRAP196-862D35.
HHCS 3/8-16X1 GR5802-017C36.
WASHER FLAT 3/8 USS PLT804-011C37.
WASHER LOCK SPRING 3/8 PLT804-013C38.
NUT HEX 3/8-16 PLT803-014C39.
HHCS 3/8-16X3 GR5802-024C40.
Drive
RevisionCommentsPart DescriptionPart No.Ref.
Refer to "Double Slector Valve
(810-274C)" forbreakdown
04/10/13 - 43 - 196-359P
Page 44
Table of Contents Part Number Index
Veris Drive Controller
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
21827
196-359P - 44 - 04/10/13
Page 45
Table of Contents Part Number Index
Veris Drive Controller
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg21827
VERIS MOUNTVER-195162.
VERIS SUCTION CUPVER-214633.
VERIS POWER/COMMCABLE 55'VER-214754.
VERIS EXT. CONTROLVER-215685.
DJ RADARW/HARDWARE833-179C6.
VERIS SOLENOID CABLEVER-183757.
VERIS PWR PRT ADPTR-HYD DRIVEVER-197298.
VERIS ENCODER W/ CABLEVER-183829.
Drive
RevisionCommentsPart DescriptionPart No.Ref.
Includes Power Cable to BatteryVERIS CAB CONSOLEVER-279471.
04/10/13 - 45 - 196-359P
Page 46
Table of Contents Part Number Index
Seed Rate Adjustment Handle (118-881S)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20462
196-359P - 46 - 04/10/13
Page 47
Table of Contents Part Number Index
Seed Rate Adjustment Handle (118-881S)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20462
NUT HEX 5/16-18 PLT803-008C1.
WASHER LOCK SPRING 5/16 PLT804-009C2.
WASHER FLAT 5/16 USS PLT804-010C3.
HHCS 3/8-16X3/4 GR5802-014C4.
WASHER LOCK SPRING 3/8 PLT804-013C5.
WASHER FLAT 3/8 SAE PLT804-012C6.
HHCS 5/16-18X3/4 GR5802-007C7.
SNAP RING EXT 17 MM800-003C8.
BRG BALL 17IDX40OD 6203822-008C9.
WASHER ADJ HANDLE BRG804-001C10.
8FT EW SEED RATE ADJ HANDLE175-243H11.
WASHER FLAT 5/8 SAE PLT804-021C12.
WASHER MACH 1.19 X .63 X 18GA804-040C13.
ADJUSTMENT HANDLE PIVOT109-069D14.
PIN COTTER3/16 X 1 1/4 PLT805-016C15.
NUT WING 1/2-13 PLT803-016C16.
ADJ LOCK PLATE ASS'Y - 1 1/2 W109-025H17.
SCREW RD HD 8-32 X 3/8 BRASS801-001C18.
WASHER FLAT #8 BRASS804-003C19.
REAR SEED ADJ GUIDE 6 3/4 LONG819-109C20.
3N-40 SEED RATE ADJ WLDMNT118-880H21.
WASHER INTERNAL STAR #8 BRASS804-002C22.
NUT HEX 8-32 BRASS803-035C23.
NUT HEX LOCK 1/4-20 FLG803-088C24.
HFSS 1/4-20X5/8 GR5802-196C25.
1 3/4 WIDE FEEDER CUP PLUG817-087C26.
Seed Rate Adjustment Handle118-881S
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 47 - 196-359P
Page 48
Table of Contents Part Number Index
Feeder Cup Channel (Center 7.5")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20464
196-359P - 48 - 04/10/13
Page 49
Table of Contents Part Number Index
Feeder Cup Channel (Center 7.5")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20464
5 5/8 BOX DVDR FOR 7 1/2 ROW118-340D1.
7 1/16 BOX DIVIDER - 7 1/2118-467D2.
BOX DVDR 4.00 X 60DEG118-433D3.
BOX DIVIDER FOR 10 ROW118-356D4.
4 13/16 BOX DVDR FOR 7 1/2 ROW118-339D5.
4 5/8 BOX DVDR FOR 8 ROW118-370D6.
7 5/8 BOX DVDR FOR 8 ROW118-373D7.
7 1/16 BOX DIVIDER - 7 1/2118-467D8.
HHCS 1/4-20X3/4 GR5802-004C9.
2SNT SEED BOX DIVIDER CLIP118-341D10.
3N-40 7.5 CEN FEEDER CUP TRAY118-624D11.
WASHER LOCK SPRING 3/8 PLT804-013C12.
WASHER RETAINING804-031C13.
SPACER TUBE X 1.207118-443D14.
SPACER TUBE X 4.078118-346D15.
SPACER TUBE X 3.078118-376D16.
185C058TUBE X 6.578118-353D17.
SPACER TUBE X 2.470118-436D18.
5/8 SHAFT LOCKING COLLAR890-350C19.
SCREW SET 5/16-18 SKT KP X 3/8801-035C20.
FEEDER CUP BEARING ASSEMBLY118-226S21.
BEARING HUB 40A15118-508D22.
FEEDER CUP BEARING HOUSING118-336D23.
BRG 30IDX55OD MM822-103C24.
SNAP RING EXT BASIC 1 3/16800-004C25.
SNAP RING INTERNAL 2.165800-107C26.
MACHINED ADJUSTMENT SPOOL109-091D27.
3N-40 7.5 FD CUP SQ DRIVE BAR118-629D28.
PM SEED CUP SPROCKET890-190C29.
SEED CUP SLEEVE817-074C30.
SEED CUP ADJUSTMENT HANDLE817-071C31.
SEED CUP RIGHT HALF817-069C32.
SEED CUP DOOR817-070C33.
SEED CUP LEFT HALF817-068C34.
SCR SELF TAP 8X3/8 TYPE25 BT801-057C35.
NYLON WASHER-SPLIT817-004C36.
SEED CUP WASHER RETAINER817-073C37.
SEED CUP ASSEMBLY817-075C38.
HHCS 3/8-16X3/4 GR5802-014C39.
WASHER FLAT 3/8 SAE PLT804-012C40.
PIN ROLL 3/16X1 1/4 PLT805-023C41.
CLAMP HOSE 1 5/8 NO. 26800-009C42.
END WHEEL FERTILIZER HOSE816-037C43.
NUT HEX WHIZ 1/4-20 PLT803-194C44.
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 49 - 196-359P
Page 50
Table of Contents Part Number Index
15 ft Feeder Cup Channel (LH 7.5")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20463
196-359P - 50 - 04/10/13
Page 51
Table of Contents Part Number Index
15 ft Feeder Cup Channel (LH 7.5")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20463
5 5/8 BOX DVDR FOR 7 1/2 ROW118-340D1.
7 1/16 BOX DIVIDER - 7 1/2118-467D2.
HHCS 1/4-20X3/4 GR5802-004C3.
2SNT SEED BOX DIVIDER CLIP118-341D4.
3N-40 7.5 LH FEEDER CUP TRAY118-623D5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
WASHER RETAINING804-031C7.
SPACER TUBE X 4.078118-346D8.
5/8 SHAFT LOCKING COLLAR890-350C9.
SCREW SET 5/16-18 SKT KP X 3/8801-035C10.
FEEDER CUP BEARING ASSEMBLY118-226S11.
BEARING HUB 40A15118-508D12.
FEEDER CUP BEARING HOUSING118-336D13.
BRG 30IDX55OD MM822-103C14.
SNAP RING EXT BASIC 1 3/16800-004C15.
SNAP RING INTERNAL 2.165800-107C16.
MACHINED ADJUSTMENT SPOOL109-091D17.
3N-40 7.5 FD CUP SQ DRIVE BAR118-629D18.
PM SEED CUP SPROCKET890-190C19.
SEED CUP SLEEVE817-074C20.
SEED CUP ADJUSTMENT HANDLE817-071C21.
SEED CUP RIGHT HALF817-069C22.
SEED CUP DOOR817-070C23.
SEED CUP LEFT HALF817-068C24.
SCR SELF TAP 8X3/8 TYPE25 BT801-057C25.
NYLON WASHER-SPLIT817-004C26.
SEED CUP WASHER RETAINER817-073C27.
SEED CUP ASSEMBLY817-075C28.
HHCS 3/8-16X3/4 GR5802-014C29.
WASHER FLAT 3/8 SAE PLT804-012C30.
PIN ROLL 3/16X1 1/4 PLT805-023C31.
CLAMP HOSE 1 5/8 NO. 26800-009C32.
END WHEEL FERTILIZER HOSE816-037C33.
NUT HEX WHIZ 1/4-20 PLT803-194C34.
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 51 - 196-359P
Page 52
Table of Contents Part Number Index
Feeder Cup Channel (RH 7.5")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20465
196-359P - 52 - 04/10/13
Page 53
Table of Contents Part Number Index
Feeder Cup Channel (RH 7.5")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20465
5 5/8 BOX DVDR FOR 7 1/2 ROW118-340D1.
7 1/16 BOX DIVIDER - 7 1/2118-467D2.
HHCS 1/4-20X3/4 GR5802-004C3.
2SNT SEED BOX DIVIDER CLIP118-341D4.
3N-40 7.5 RH FEEDER CUP TRAY118-625D5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
WASHER RETAINING804-031C7.
SPACER TUBE X 4.078118-346D8.
5/8 SHAFT LOCKING COLLAR890-350C9.
SCREW SET 5/16-18 SKT KP X 3/8801-035C10.
FEEDER CUP BEARING ASSEMBLY118-226S11.
BEARING HUB 40A15118-508D12.
FEEDER CUP BEARING HOUSING118-336D13.
BRG 30IDX55OD MM822-103C14.
SNAP RING EXT BASIC 1 3/16800-004C15.
SNAP RING INTERNAL 2.165800-107C16.
MACHINED ADJUSTMENT SPOOL109-091D17.
3N-40 7.5 FD CUP SQ DRIVE BAR118-629D18.
PM SEED CUP SPROCKET890-190C19.
SEED CUP SLEEVE817-074C20.
SEED CUP ADJUSTMENT HANDLE817-071C21.
SEED CUP RIGHT HALF817-069C22.
SEED CUP DOOR817-070C23.
SEED CUP LEFT HALF817-068C24.
SCR SELF TAP 8X3/8 TYPE25 BT801-057C25.
NYLON WASHER-SPLIT817-004C26.
SEED CUP WASHER RETAINER817-073C27.
SEED CUP ASSEMBLY817-075C28.
HHCS 3/8-16X3/4 GR5802-014C29.
WASHER FLAT 3/8 SAE PLT804-012C30.
PIN ROLL 3/16X1 1/4 PLT805-023C31.
CLAMP HOSE 1 5/8 NO. 26800-009C32.
END WHEEL FERTILIZER HOSE816-037C33.
NUT HEX WHIZ 1/4-20 PLT803-194C34.
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 53 - 196-359P
Page 54
Table of Contents Part Number Index
Feeder Cup Channel (LH 10")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20466
196-359P - 54 - 04/10/13
Page 55
Table of Contents Part Number Index
Feeder Cup Channel (LH 10")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20466
BOX DIVIDER FOR 10 ROW118-356D1.
BOX DVDR 5.31 X 60DEG118-371D2.
HHCS 1/4-20X3/4 GR5802-004C3.
2SNT SEED BOX DIVIDER CLIP118-341D4.
3N-40 10 LH FEEDER CUP TRAY118-626D5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
WASHER RETAINING804-031C7.
SPACER TUBE X 3.766118-375D8.
5/8 SHAFT LOCKING COLLAR890-350C9.
SCREW SET 5/16-18 SKT KP X 3/8801-035C10.
FEEDER CUP BEARING ASSEMBLY118-226S11.
BEARING HUB 40A15118-508D12.
FEEDER CUP BEARING HOUSING118-336D13.
BRG 30IDX55OD MM822-103C14.
SNAP RING EXT BASIC 1 3/16800-004C15.
SNAP RING INTERNAL 2.165800-107C16.
MACHINED ADJUSTMENT SPOOL109-091D17.
3N-40 10 FD CUP SQ DRIVE BAR118-630D18.
PM SEED CUP SPROCKET890-190C19.
SEED CUP SLEEVE817-074C20.
SEED CUP ADJUSTMENT HANDLE817-071C21.
SEED CUP RIGHT HALF817-069C22.
SEED CUP DOOR817-070C23.
SEED CUP LEFT HALF817-068C24.
SCR SELF TAP 8X3/8 TYPE25 BT801-057C25.
NYLON WASHER-SPLIT817-004C26.
SEED CUP WASHER RETAINER817-073C27.
SEED CUP ASSEMBLY817-075C28.
HHCS 3/8-16X3/4 GR5802-014C29.
WASHER FLAT 3/8 SAE PLT804-012C30.
PIN ROLL 3/16X1 1/4 PLT805-023C31.
CLAMP HOSE 1 5/8 NO. 26800-009C32.
END WHEEL FERTILIZER HOSE816-037C33.
NUT HEX WHIZ 1/4-20 PLT803-194C34.
BOX DIVIDER FOR 10 ROW118-356D35.
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 55 - 196-359P
Page 56
Table of Contents Part Number Index
Feeder Cup Channel (Center 10")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20467
196-359P - 56 - 04/10/13
Page 57
Table of Contents Part Number Index
Feeder Cup Channel (Center 10")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20467
BOX DIVIDER FOR 10 ROW118-356D1.
BOX DVDR 7.75 X 60DEG118-470D2.
HHCS 1/4-20X3/4 GR5802-004C3.
2SNT SEED BOX DIVIDER CLIP118-341D4.
3N-40 10 CEN FEEDER CUP TRAY118-627D5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
WASHER RETAINING804-031C7.
185C058TUBE X 6.578118-353D8.
5/8 SHAFT LOCKING COLLAR890-350C9.
SCREW SET 5/16-18 SKT KP X 3/8801-035C10.
FEEDER CUP BEARING ASSEMBLY118-226S11.
BEARING HUB 40A15118-508D12.
FEEDER CUP BEARING HOUSING118-336D13.
BRG 30IDX55OD MM822-103C14.
SNAP RING EXT BASIC 1 3/16800-004C15.
SNAP RING INTERNAL 2.165800-107C16.
MACHINED ADJUSTMENT SPOOL109-091D17.
3N-40 7.5 FD CUP SQ DRIVE BAR118-629D18.
PM SEED CUP SPROCKET890-190C19.
SEED CUP SLEEVE817-074C20.
SEED CUP ADJUSTMENT HANDLE817-071C21.
SEED CUP RIGHT HALF817-069C22.
SEED CUP DOOR817-070C23.
SEED CUP LEFT HALF817-068C24.
SCR SELF TAP 8X3/8 TYPE25 BT801-057C25.
NYLON WASHER-SPLIT817-004C26.
SEED CUP WASHER RETAINER817-073C27.
SEED CUP ASSEMBLY817-075C28.
HHCS 3/8-16X3/4 GR5802-014C29.
WASHER FLAT 3/8 SAE PLT804-012C30.
PIN ROLL 3/16X1 1/4 PLT805-023C31.
CLAMP HOSE 1 5/8 NO. 26800-009C32.
END WHEEL FERTILIZER HOSE816-037C33.
NUT HEX WHIZ 1/4-20 PLT803-194C34.
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 57 - 196-359P
Page 58
Table of Contents Part Number Index
Feeder Cup Channel (RH 10")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20468
196-359P - 58 - 04/10/13
Page 59
Table of Contents Part Number Index
Feeder Cup Channel (RH 10")
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20468
BOX DIVIDER FOR 10 ROW118-356D1.
BOX DVDR 5.31 X 60DEG118-371D2.
HHCS 1/4-20X3/4 GR5802-004C3.
2SNT SEED BOX DIVIDER CLIP118-341D4.
3N-40 10 RH FEEDER CUP TRAY118-628D5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
WASHER RETAINING804-031C7.
185C058TUBE X 6.578118-353D8.
5/8 SHAFT LOCKING COLLAR890-350C9.
SCREW SET 5/16-18 SKT KP X 3/8801-035C10.
FEEDER CUP BEARING ASSEMBLY118-226S11.
BEARING HUB 40A15118-508D12.
FEEDER CUP BEARING HOUSING118-336D13.
BRG 30IDX55OD MM822-103C14.
SNAP RING EXT BASIC 1 3/16800-004C15.
SNAP RING INTERNAL 2.165800-107C16.
MACHINED ADJUSTMENT SPOOL109-091D17.
3N-40 7.5 FD CUP SQ DRIVE BAR118-629D18.
PM SEED CUP SPROCKET890-190C19.
SEED CUP SLEEVE817-074C20.
SEED CUP ADJUSTMENT HANDLE817-071C21.
SEED CUP RIGHT HALF817-069C22.
SEED CUP DOOR817-070C23.
SEED CUP LEFT HALF817-068C24.
SCR SELF TAP 8X3/8 TYPE25 BT801-057C25.
NYLON WASHER-SPLIT817-004C26.
SEED CUP WASHER RETAINER817-073C27.
SEED CUP ASSEMBLY817-075C28.
HHCS 3/8-16X3/4 GR5802-014C29.
WASHER FLAT 3/8 SAE PLT804-012C30.
PIN ROLL 3/16X1 1/4 PLT805-023C31.
CLAMP HOSE 1 5/8 NO. 26800-009C32.
END WHEEL FERTILIZER HOSE816-037C33.
NUT HEX WHIZ 1/4-20 PLT803-194C34.
Metering System
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 59 - 196-359P
Page 60
Table of Contents Part Number Index
Loop Shaft Monitor (2 Channel 116-282A) (3 Channel 116-283A)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
34220
196-359P - 60 - 04/10/13
Page 61
Table of Contents Part Number Index
Loop Shaft Monitor (2 Channel 116-282A) (3 Channel 116-283A)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
RevisionCommentsPart DescriptionPart No.Ref.
Image No.dwg34220
HFSS 1/4-20X3/4 GR5802-257C1.
HOSE CLIP 5/8 I.D.800-052C2.
NUT HEX LOCK 1/4-20 FLG803-088C3.
CABLE TIE, NYLON7700264.
MAGNET, ADHESIVE BACKED, LARGE5400175.
NUT HEX JAM, PLASTIC M16 X 27104256.
SHAFT SENSOR MOUNT116-019D7.
SCR SELF TAP #10 X 3/4801-199C8.
LOUP SHAFT SENSOR 2&3 CHANNEL2531009.
SMALL CUP SENSOR MOUNT116-020D10.
LOUP 3 CHANNEL SHAFT MONITOR25301711.
LOUP 2 CHANNEL SHAFT MONITOR25301612.
SHAFT MONITOREXT. 30' 6P WP833-595C13.
HARNESS 3 SHAFT MONITOR LOUP31895114.
LOUP 3 CHANNEL SHAFT MONITOR25301715.
SHAFT MONITOREXT. 25' 4P WP833-596C16.
HARNESS 2 SHAFT MONITOR LOUP31891717.
Metering System
04/10/13 - 61 - 196-359P
Page 62
Table of Contents Part Number Index
10 Series Opener Arms & Mounts
(Applies to 3N-4010 & 3N-4010HDF only)
20457
196-359P - 62 - 04/10/13
Page 63
Table of Contents Part Number Index
10 Series Opener Arms & Mounts
(Applies to 3N-4010 & 3N-4010HDF only)
Image No.dwg20457
HFS 1/2-13 X 5 3/4802-419C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
SING OPENER INNER PIVOT TUBE198-246D3.
PARALLEL ARM PIVOT BUSHING817-084C4.
SING OPENER LOWER ARM WELDMENT198-619H5.
SPRING EXT 1 5/8OD X 6.6X.177807-116C6.
6 13/16 SPRING STRAP198-239D7.
SING OPENER UPPER ARM WELDMENT198-618H8.
PSS OPENER MOUNT REAR WLDMT198-614H9.
PSS OPENER MOUNT FRONT WLDMT198-613H10.
U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C11.
WASHER LOCK SPRING 5/8 PLT804-022C12.
NUT HEX 5/8-11 PLT803-021C13.
HHCS 1/4-20X3 GR5802-274C15.
NUT-LOCK 1/4-20 PLT803-007C16.
END WHEEL FERTILIZER HOSE816-037C17.
SCREW HEX SLT10-16X1/2P.THD CT801-002C18.
3N-40 SEED HOSE CLAMP PLATE196-849D19.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Center frame openers only10P 20P UP FLOAT LIMITER122-172D14.
04/10/13 - 63 - 196-359P
Page 64
Table of Contents Part Number Index
10 Series Opener Body
(Applies to 3N-4010 & 3N-4010HDF only)
20458
196-359P - 64 - 04/10/13
Page 65
Table of Contents Part Number Index
10 Series Opener Body
(Applies to 3N-4010 & 3N-4010HDF only)
Image No.dwg20458
3N-40 SEED TUBE NO SENSOR HOLE817-530C1.
10 SERIES SINGULATING OPENER198-616H2.
PIN COTTER3/32 X 1 LONG805-063C3.
PIN CLEVIS 1/4 X 3 23/64 USBL805-299C4.
SEED FLAP MOUNTING CLIP, SING198-241D5.
DD W/205 BRG-PLD FLNG-4MM107-138S7.
DD BRG FLANGE DUST COVER107-111D8.
WASHER MACH 1.19 X .63 X 18GA804-040C9.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C10.
PIN ROLL 5/16 X 5/8 PLT805-335C11.
SCRAPER-SPREADER 10-20 SER198-491H12.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C13.
HSG RIBB FLG 6BOLTPLT890-466C14.
BEARING AA205DD188-001V15.
FLAT DISK BLADE-4MM THICK820-256C16.
HHCS 3/8-16X1 1/4 GR5802-079C17.
NUT HEX 3/8-16 PLT803-014C18.
WASHER LOCK SPRING 3/8 PLT804-013C19.
10P AD OUTSIDE SCRAPER MOUNT122-169D20.
AIR DESIGN SCRAPER J.D.2.5W RHAD2101021.
AIR DESIGN SCRAPER J.D.2.5W LHAD2101122.
AIR DESIGN SCRAPER J.D.MNT RHAD2101223.
AIR DESIGN SCRAPER J.D.MNT LHAD2101324.
AIR DESIGN SCRAPER J.D.SPRINGAD2101425.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
S/N B1011B+SEED FLAP, RUBBER, SEED-LOK816-302C6.
S/N B1010B-SEED FLAP, UHMW, LONG817-349C6.
04/10/13 - 65 - 196-359P
Page 66
Table of Contents Part Number Index
HD10 Series Opener Arms & Mounts
(Applies to 3N-4010 & 3N-4010HDF only)
27405
196-359P - 66 - 04/10/13
Page 67
Table of Contents Part Number Index
HD10 Series Opener Arms & Mounts
(Applies to 3N-4010 & 3N-4010HDF only)
Image No.dwg27405
HD10P OPENER WELDMENT298-855H1.
HFS 1/2-13X6 1/8GR5 PLT802-745C2.
PARALLEL ARM PIVOT BUSHING817-084C3.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C4.
25 SERIES UPPER PARALLEL ARM298-513H6.
SPRING EXT 1.575O.D.X.225 WIRE807-076C7.
25P REAR OPENER INNER PIVOTTB198-295D9.
25 SERIES LOWER PARALLEL ARM298-510H10.
U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C11.
NUT HEX 5/8-11 PLT803-021C12.
25P FRONT OPENER MOUNT WELDMT298-884H13.
WASHER LOCK SPRING 5/8 PLT804-022C14.
HD10P REAR OPENER MOUNT WELDMT298-856H15.
LOCKUP PIN FOR 10HD OPENER398-456H16.
PIN LINCH 3/16 X 1 9/16 LONG805-240C17.
25P UP FLOATLIMITER122-173D18.
HHCS 3/8-16X1 1/4 GR5802-079C19.
WASHER LOCK SPRING 3/8 PLT804-013C20.
NUT HEX 3/8-16 PLT803-014C21.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Used with dual springs25P UPPER SPRING LINK198-292D5.
Used with dual springs25P LOWER SPRING LINK198-293D8.
Used with single springs3 13/32 SPRING STRAP198-240D22.
04/10/13 - 67 - 196-359P
Page 68
Table of Contents Part Number Index
HD10 Series Opener Body
(Applies to 3N-4010 & 3N-4010HDF only)
23356
196-359P - 68 - 04/10/13
Page 69
Table of Contents Part Number Index
HD10 Series Opener Body
(Applies to 3N-4010 & 3N-4010HDF only)
Image No.dwg23356
HD10P OPENER WELDMENT298-855H1.
CABLE TIE .19X7.25 1.75D 50LB800-112C2.
PIN COTTER3/32 X 1 LONG805-063C3.
T-HANDLE ASSEMBLY817-328C4.
PIN ROLL 5/32 X 5/8 PLT805-186C5.
SPRING .540 O.D.X 1 1/4 X.054W807-106C6.
OPENER TRUNION817-347C7.
PIN CLEVIS 3/8 X 2 1/8 USABLE805-154C8.
PIN ROLL 5/16 X 7/8805-250C10.
PIN ROLL 5/16 X 5/8 PLT805-335C11.
25P SCRAPER SEPARATOR WLDMT404-170H12.
RHSNB 5/16-18X3/4 GR5802-092C13.
NUT HEX WHIZ 5/16-18 PLT803-043C14.
WASHER MACH 1.19 X .63 X 18GA804-040C16.
BEARING AA205DD188-001V17.
4.0 MM 15 DISK (21 DEG BEVEL)820-287C18.
RIBB BRG FLNG .266 MT HOLE PLT890-466C19.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C20.
4.0 MM 15 DISC W/ 5/8 ASSY404-121S21.
DD BRG FLANGE DUST COVER107-111D22.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C23.
PIN CLEVIS 1/4 X 2 55/64 USBL805-190C24.
HD10 OPENER SEED TUBE TOP CAP198-318D25.
END WHEEL FERTILIZER HOSE816-037C27.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C28.
RHSNB 1/2-13X1 GR5802-183C29.
SEED TUBE 25S FPU TB&CAP NO HL817-696C30.
SEED TUBE 25S HOOK CLIP198-331D31.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Includes items 30 & 31SEED TUBE FPU TUBE & CLIP403-215S9.
Used with Unit Mount CoulterSHIELD,DISK404-139D15.
Used without CoulterTRASH GUARDWELDMENT288-310H26.
04/10/13 - 69 - 196-359P
Page 70
Table of Contents Part Number Index
HD10 Series Keeton Seed Firmer (Option)
(Applies to 3N-4010 & 3N-4010HDF only)
21855
196-359P - 70 - 04/10/13
Page 71
Table of Contents Part Number Index
HD10 Series Keeton Seed Firmer (Option)
(Applies to 3N-4010 & 3N-4010HDF only)
Image No.dwg21855
KEETON NARROW TAIL1208251.
BRACKET FOR 890-840C REV A&B129BXT8222.
RHSNB 3/8-16X1 3/4 GR5802-252C3.
NUT HEX 3/8-16 PLT803-014C4.
WASHER LOCK SPRING 3/8 PLT804-013C5.
NUT HEX WHIZ 5/16-18 PLT803-043C6.
HHCS 5/16-18X2 1/2 GR5802-172C7.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 71 - 196-359P
Page 72
Table of Contents Part Number Index
HD10 Series Seed-Lok (Option)
(Applies to 3N-4010 & 3N-4010HDF only)
17663
196-359P - 72 - 04/10/13
Page 73
Table of Contents Part Number Index
HD10 Series Seed-Lok (Option)
(Applies to 3N-4010 & 3N-4010HDF only)
Image No.dwg17663
PIN COTTER5/32 X 1 1/4 LG805-045C1.
LEVER, SEED LOK404-213D2.
SPRING .540 O.D.X 1 1/4 X.054W807-106C3.
LOCK ROD WELD404-088H4.
SEED LOK MOUNT404-144D5.
RHSNB 5/16-18X3/4 GR5802-092C6.
NUT HEX WHIZ 5/16-18 PLT803-043C7.
JD KINZE SEED LOK LOWER MOUNT206-010D8.
SNAP RING 1/2 EXTERNAL HEAVY800-166C9.
SEED LOK WHEEL ARM404-061D10.
SCR HX SKT BUT CP 3/8-16X3/4801-078C11.
WASHER INTERNAL STAR 3/8 PLT.804-078C12.
RPBY 188-008V122-231A13.
SCR PH THD FMG #10X1/2 TP ZP801-084C14.
RETAINER W/BONDED SEAL 4BLT816-173C15.
5/8 X 6 SEED LOK WHEEL817-191C16.
6 SEED LOK ASSEMBLY206-014S17.
WASHER 1.5 X .51 X .187804-112C18.
SPRING EXT 1 X 4 X .135 WD807-125C19.
SEED LOK PIVOT PIN206-011D20.
LEVER STOP404-212D21.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 73 - 196-359P
Page 74
Table of Contents Part Number Index
20 Series Opener Arms & Mounts
(Applies to 3N-4020 only)
20459
196-359P - 74 - 04/10/13
Page 75
Table of Contents Part Number Index
20 Series Opener Arms & Mounts
(Applies to 3N-4020 only)
Image No.dwg20459
HFS 1/2-13 X 5 3/4802-419C1.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C2.
SING OPENER INNER PIVOT TUBE198-246D3.
PARALLEL ARM PIVOT BUSHING817-084C4.
SING OPENER LOWER ARM WELDMENT198-619H5.
SING OPENER UPPER ARM WELDMENT198-618H8.
PSS OPENER MOUNT REAR WLDMT198-614H9.
PSS OPENER MOUNT FRONT WLDMT198-613H10.
20 SER SING FRT INNER PIVOT TB198-247D11.
U-BOLT 5/8-11 X 7 1/32 X 6 1/2806-053C12.
WASHER LOCK SPRING 5/8 PLT804-022C13.
NUT HEX 5/8-11 PLT803-021C14.
HHCS 1/4-20X3 GR5802-274C16.
NUT-LOCK 1/4-20 PLT803-007C17.
END WHEEL FERTILIZER HOSE816-037C18.
SCREW HEX SLT10-16X1/2P.THD CT801-002C19.
3N-40 SEED HOSE CLAMP PLATE196-849D20.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Used with 1x12 Press Wheels.SPRING EXT 1 5/8OD X 6.6X.177807-116C6.
Used with 1x10 Press Wheels.SPRING EXT 1.575O.D.X.225 WIRE807-076C6.
Used with 807-116C.6 13/16 SPRING STRAP198-239D7.
Used with 807-076C.3 13/32 SPRING STRAP198-240D7.
Center frame openers only10P 20P UP FLOAT LIMITER122-172D15.
04/10/13 - 75 - 196-359P
Page 76
Table of Contents Part Number Index
20 Series Opener Body
(Applies to 3N-4020 only)
20485
196-359P - 76 - 04/10/13
Page 77
Table of Contents Part Number Index
20 Series Opener Body
(Applies to 3N-4020 only)
Image No.dwg20485
3N-40 SEED TUBE NO SENSOR HOLE817-530C1.
20 SERIES SINGULATING OPENER198-615H2.
PIN COTTER3/32 X 1 LONG805-063C3.
PIN CLEVIS 1/4X1 31/64 USBL805-296C4.
SEED FLAP MOUNTING CLIP, SING198-241D5.
DD W/205 BRG-PLD FLNG-4MM107-138S8.
WASHER MACH 1.19 X .63 X 18GA804-040C9.
HHCS 5/8-11X1 1/2 GR5 NYL802-228C10.
PIN ROLL 5/16 X 5/8 PLT805-335C11.
RIVET,BUTTON HEAD 1/4 X 1/2800-213C13.
HSG RIBB FLG 6BOLTPLT890-466C14.
BEARING AA205DD188-001V15.
FLAT DISK BLADE-4MM THICK820-256C16.
20 SER OPNR CAM PIN198-202D17.
SNAP RING EXT 5/8 .050 T800-118C18.
RPBY 812-328C298-324S19.
CASTING - STAINLESS T-HANDLE812-302C20.
NUT HEX 7/16-20 GR8803-307C21.
WASHER LOCK 7/16 PLT804-014C22.
20 SER OPNR PW CAM198-201D23.
PRESS WHEEL ARM PIVOT BUSHING817-083C24.
SPRING COMP 5/8 OD X 1 3/4 LG807-172C25.
WASHER FLAT 3/8 SAE PLT804-012C26.
PIN COTTER1/8 X 3/4805-067C27.
20P SIDE DEPTH WHEEL ARM198-265D28.
WASHER LOCK SPRING 5/8 PLT804-022C30.
HHCS 5/8-11X2 1/2 GR5 NYL802-179C31.
HFSS 5/16-18X1/2 GR5802-352C33.
NUT HEX WHIZ 5/16-18 PLT803-043C34.
2X13 D.W.OUTER RIM HALF814-082C35.
2X13 SIDE DEPTH TIRE814-083C36.
20 SER SIDE DEPTH WL STIFF PLT198-183D37.
2X13 D.W.INNER RIM HALF814-081C38.
HHCS 7/16-20 2 3/4 GR8802-694C39.
GREASE ZERK STRAIGHT 1/4-28800-001C41.
WASHER FLAT 1.31ODX.65IDX.188T804-195C42.
HHCS 5/8-11X2 GR5 NYL802-430C43.
RHSNB 5/16-18X3/4 GR5802-092C44.
U CUP SEAL816-723C45.
20P DEPTH WHL OUTER BUSHING298-001D46.
20P DEPTH WHL ECCENTRIC BUSHNG198-266D47.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Used with Seed-Lok (shown).SEED FLAP, RUBBER, SEED-LOK816-302C6.
Used without Seed-Lok.SEED FLAP, UHMW, LONG817-349C6.
Includes 13-16RPBY 107-135S107-133S7.
S/N 7388B+SCRAPER-SPREADER 10-20 SER198-491H12.
S/N 7387B-SCRAPER-SPREADER 10-20SER 2003812-309C12.
Includes 45-4720P ELIMINATOR BUSHING ASSY198-998S29.
Includes 33-38, 442X13 DEPTH WHEEL ASSY198-057S32.
OptionSEP &FERTTUBE 10-20SER 1999122-257H40.
Includes 20, 23-2720 SER OPENER T-HANDLE SUBASSY198-956K48.
04/10/13 - 77 - 196-359P
Page 78
Table of Contents Part Number Index
Keeton Seed Firmer (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20252
196-359P - 78 - 04/10/13
Page 79
Table of Contents Part Number Index
Keeton Seed Firmer (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20252
KEETON NARROW TAIL1208251.
KEETON BRACKET 10/20 SERIES1290012.
KEETON GUARD129BXT8273.
RHSNB 3/8-16X2 GR5802-411C4.
NUT HEX 3/8-16 PLT803-014C5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 79 - 196-359P
Page 80
Table of Contents Part Number Index
Air Design Scraper (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20434
196-359P - 80 - 04/10/13
Page 81
Table of Contents Part Number Index
Air Design Scraper (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20434
10P20P AD INSIDE SCRAPER MOUNT122-168D1.
HHCS 3/8-16X1 1/4 GR5802-079C2.
WASHER LOCK SPRING 3/8 PLT804-013C3.
NUT HEX 3/8-16 PLT803-014C4.
SCRAPER-SPRING LOAD-AIR DESIGN890-357C5.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 81 - 196-359P
Page 82
Table of Contents Part Number Index
Side Wheel Scraper (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20185
196-359P - 82 - 04/10/13
Page 83
Table of Contents Part Number Index
Side Wheel Scraper (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20185
20P SIDE WHEEL SCRAPER MOUNT198-264D1.
WASHER LOCK SPRING 5/16 PLT804-009C2.
HHCS 5/16-18X5/8802-705C3.
RHSNB 3/8-16X3/4 GR5802-149C4.
20P SIDE WHEEL SCRAPER198-263D5.
NUT FLANGE LOCK 3/8-16 PLT803-209C6.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 83 - 196-359P
Page 84
Table of Contents Part Number Index
10 & 20 Series Seed-Lok (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20039
196-359P - 84 - 04/10/13
Page 85
Table of Contents Part Number Index
10 & 20 Series Seed-Lok (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20036
PIN COTTER3/16 X 1805-069C1.
SEED LOCK LOCK-UP CAM122-166D2.
SPRING COMP .85ODX2.0LGX.067W807-188C3.
PIN COTTER1/4 X 1 PLT805-020C4.
20 SER SEED LOCK LOCK-UP BAR122-165D6.
WASHER LOCK SPRING 3/8 PLT804-013C7.
NUT HEX 3/8-16 PLT803-014C8.
HHCS 3/8-16X1 1/2 GR5802-022C9.
SEED LOCK MOUNT, SINGULATING122-250H10.
SEED LOCK ARM, SINGULATING122-164D11.
SPRING, 1 O.D.X.125WIREX 3 1/2807-101C12.
5 SEED-LOK WHL ARM PIVOTPIN122-120D13.
RING SNAP EXTERNAL '"E'" 1/2800-093C14.
WASHER INTERNAL STAR 3/8 PLT.804-078C15.
5/8 X 5 SEED FIRMING WHEEL817-134C18.
BEARING 203 SEED-LOK WITH PIN188-008V19.
SCR PH THD FMG #10X1/2 TP ZP801-084C20.
RETAINER W/BONDED SEAL 4BLT816-173C21.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Shown.10 SER SEED LOCK LOCK-UP BAR122-167D5.
20 Series only.SCR HX SKT BUT CP 3/8-16X3/4801-078C16.
Includes 18,19,20 & 21SD-LK 203 BEARING WHEEL ASSY122-201S17.
10 Series only.LHS CP 3/8-16X3/4 GR8 PLATED801-141C22.
10 Series onlyWASHER FLAT 3/8 USS PLT804-011C23.
04/10/13 - 85 - 196-359P
Page 86
Table of Contents Part Number Index
Coulter
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20263
196-359P - 86 - 04/10/13
Page 87
Table of Contents Part Number Index
Coulter
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20263
CLTR CASTING ASSY249-050S1.
CLTR SWING ARM WLMT249-051H2.
WASHER MACH 1 1/4X3/4X14GA804-156C3.
SNAP RING 3/4 EXTERNAL HEAVY800-164C4.
EYE BOLT 3/4-10X14 3/4 LG SP802-718C5.
WASHER MACH 1 7/8X1 1/4X 14GA804-165C6.
SPRING 2.25 O.D. X .5 COIL149-559D7.
COULTER SPRING GUIDE TUBE805-331C8.
COULTER SPRING WASHER149-558D9.
GREASE ADAPT1/4-28M X 1/4 TB800-211C10.
BUSHING 1X3/4X1 1/8 FLG HD817-513C11.
COULTER SPRING BAR 14 3/4 BLK204-295D12.
HHCS 7/8-9X3 GR5802-332C13.
WASHER LOCK SPRING 7/8 PLT804-037C14.
NUT HEX 7/8-9 PLT803-049C15.
RHSNB 1/2-13X1 1/4 GR5802-214C16.
OIL-SEAL DOUBLE LIP816-009C17.
BEARING CONE LM-67048822-021C18.
BEARING CUP LM-67010822-020C19.
HUB GREASE CAP200-001D21.
GREASE ZERK STRAIGHT 1/4-28800-001C22.
PIN COTTER3/16 X 1 3/4 PLT805-017C24.
COULTER BLADE FLUTED820-018C25.
17 COULTER BLADE 5/8 WAVY820-116C25.
17 COULTER BLADE 3/4 WAVY820-082C25.
5/8 WAVY TURBO BLADE820-156C25.
WASHER LOCK SPRING 1/2 PLT804-015C26.
NUT HEX 1/2-13 PLT803-020C27.
WASHER SPINDLE - 7/8804-055C28.
NUT HEX SLOTTED 7/8-14 PLT803-029C29.
U-BOLT 5/8-11 X 4 1/32 X 4806-106C30.
COULTER CLAMP BAR149-059D31.
NUT HEX 5/8-11 PLT803-021C32.
SNAP RING EXT 1 1/4 HEAVY800-177C33.
OFFSET COULTER MOUNT PLATE149-086D34.
OFFSET COULTER BRKT F/LH BOX197-010D35.
WASHER LOCK SPRING 5/8 PLT804-022C36.
HHCS 1/2-13X1 3/4 GR5802-082C37.
NUT HEX JAM 3/4-10 PLT803-048C38.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
HD10 onlyLONG COULT. SPRING BAR204-269D12.
Includes items 19,22COULTER HUB & CUP ASSY200-039V20.
Includes items 16,17,18,20COULTER HUB PACKAGE200-002S23.
04/10/13 - 87 - 196-359P
Page 88
Table of Contents Part Number Index
Grease Bank
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
20333
196-359P - 88 - 04/10/13
Page 89
Table of Contents Part Number Index
Grease Bank
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg20333
GREASE ZERK STRAIGHT 1/8-27NPT800-130C1.
AD PUSH 1/4 TUBE 1/8 FNPT800-449C2.
TUBE NYLON 1/4OD X 062WL990-109R3.
FTG TUBE,CONNECTOR1/8 MNPT800-157C4.
FTG ADAPTER,1/8FNPT X 1/4-28M800-156C5.
HFSS 1/4-20X1/2 GR5802-148C6.
WASHER FLAT 1/4 SAE PLT804-007C7.
WASHER LOCK SPRING 1/4 PLT804-006C8.
NUT HEX 1/4-20 PLT803-006C9.
GREASE BANK MOUNT197-194D10.
GREASE ADAPT1/4-28M X 1/4 TB800-211C11.
U-BOLT 3/8-16 X 4 1/32 X 2 3/4806-111C12.
GREASE BANK MOUNT PLATE BOLTON197-058D13.
NUT HEX 3/8-16 PLT803-014C14.
WASHER LOCK SPRING 3/8 PLT804-013C15.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 89 - 196-359P
Page 90
Table of Contents Part Number Index
Coulter Tine (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
19679
196-359P - 90 - 04/10/13
Page 91
Table of Contents Part Number Index
Coulter Tine (Option)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg19679
HHCS 7/8-9X3 1/2 GR5802-126C1.
2SNT COULTER TINE820-114C2.
COULTER TINE MOUNT PLATEREAR149-570D3.
HHCS 3/8-16X1 1/2 GR5802-022C4.
WASHER FLAT 3/8 USS PLT804-011C5.
WASHER LOCK SPRING 3/8 PLT804-013C6.
NUT HEX 3/8-16 PLT803-014C7.
WASHER LOCK SPRING 7/8 PLT804-037C9.
NUT HEX 7/8-9 PLT803-049C10.
Openers
RevisionCommentsPart DescriptionPart No.Ref.
Use with part number 196-602DHHCS 7/8-9X5 1/2 GR5802-178C1.
Used with offset coulter mounts onlyCOULTER TINE OFFST MNT SPACER196-602D8.
04/10/13 - 91 - 196-359P
Page 92
Table of Contents Part Number Index
2" x 13" Single Press Wheel
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
17439
196-359P - 92 - 04/10/13
Page 93
Table of Contents Part Number Index
2" x 13" Single Press Wheel
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg17439
HHCS 5/8-11X2 1/2 GR5802-058C1.
WASHER LOCK SPRING 5/8 PLT804-022C2.
NUT HEX LOCK 1/4-20 FLG803-088C3.
2 X 13 PRESS WHEEL RIM HALF817-296C4.
BRG .63ID PRESS WHL ASY822-170C5.
2 X 13 PRESS WHEEL TIRE814-159C6.
HHFS 1/4-20 X 1 1/2 GR 5802-617C7.
2 X 13 PRESS WHEEL ASSEMBLY814-157C8.
UNIVERSAL PW ARM MACH 2&3X13199-042D9.
PARALLEL ARM PIVOT BUSHING817-084C10.
PRESS WHEEL PIVOT TUBE198-137D11.
PIN CLEVIS 3/8 X 2 1/8 USABLE805-154C12.
SPRING .540 O.D.X 1 1/4 X.054W807-106C13.
OPENER TRUNION817-347C14.
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C15.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C16.
T-HANDLE ASSEMBLY817-328C17.
PIN ROLL 5/32 X 5/8 PLT805-186C18.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
Includes 12,13,14,17 & 18PW ADJUSTMENT TRUNNION ASSY122-202S19.
04/10/13 - 93 - 196-359P
Page 94
Table of Contents Part Number Index
3" x 13" Single Press Wheel
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
17438
196-359P - 94 - 04/10/13
Page 95
Table of Contents Part Number Index
3" x 13" Single Press Wheel
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg17438
HHCS 5/8-11X2 1/2 GR5802-058C1.
WASHER LOCK SPRING 5/8 PLT804-022C2.
NUT HEX LOCK 1/4-20 FLG803-088C3.
3 X 13 PRESS WHEEL RIM HALF817-297C4.
3 X 13 PRESS WHEEL TIRE814-160C5.
BRG .63ID PRESS WHL ASY822-170C6.
HHFS 1/4-20 X 2 GR 5802-618C7.
3 X 13 PRESS WHEEL ASSEMBLY814-158C8.
UNIVERSAL PW ARM MACH 2&3X13199-042D9.
PARALLEL ARM PIVOT BUSHING817-084C10.
PRESS WHEEL PIVOT TUBE198-137D11.
PIN CLEVIS 3/8 X 2 1/8 USABLE805-154C12.
SPRING .540 O.D.X 1 1/4 X.054W807-106C13.
OPENER TRUNION817-347C14.
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C15.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C16.
T-HANDLE ASSEMBLY817-328C17.
PIN ROLL 5/32 X 5/8 PLT805-186C18.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
Includes 12,13,14,17 & 18PW ADJUSTMENT TRUNNION ASSY122-202S19.
04/10/13 - 95 - 196-359P
Page 96
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel (Part 1)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
17437
196-359P - 96 - 04/10/13
Page 97
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel (Part 1)
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg17437
HHCS 5/8-11X2 1/2 GR5802-058C1.
WASHER LOCK SPRING 5/8 PLT804-022C2.
HHCS 1/4-20X1 GR5802-005C3.
1 X 12 PRESS WHEEL RIM HALF817-330C4.
BRG .63ID PRESS WHL ASY822-170C5.
TIRE RUBBER1 X 12814-034C6.
NUT HEX LOCK 1/4-20 FLG803-088C7.
1 X 12 PRESS WHL ASSY-5203BRG814-174C8.
98 1X12 PRESS WHEEL WELDMENT199-022H9.
PARALLEL ARM PIVOT BUSHING817-084C10.
PRESS WHEEL PIVOT TUBE198-137D11.
PIN CLEVIS 3/8 X 2 1/8 USABLE805-154C12.
SPRING .540 O.D.X 1 1/4 X.054W807-106C13.
OPENER TRUNION817-347C14.
HFS 1/2-13X3 3/4 GR5 SPTHD802-421C15.
NUT HEX FLG. LOCK 1/2-13 PLT.803-169C16.
T-HANDLE ASSEMBLY817-328C17.
PIN ROLL 5/32 X 5/8 PLT805-186C18.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
Includes 12,13,14,17 & 18PW ADJUSTMENT TRUNNION ASSY122-202S19.
04/10/13 - 97 - 196-359P
Page 98
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel Short
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
18194
196-359P - 98 - 04/10/13
Page 99
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel Short
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
Image No.dwg18194
SHORT 1X12 SING OPNR PW MOUNT199-025H1.
PIN CLEVIS 7/16 X 2 25/64 USBL805-304C2.
LONG 1X12 PW HANDLE SPACER TB199-050D3.
118-433DG HANDLE199-011D4.
PIN COTTER1/8 X 3/4805-067C5.
1X12 PW 1/2 SPACER199-036D6.
1 X 12 PRESS WHL ASSY-5203BRG814-174C7.
HHCS 5/8-11X3 1/4 GR5802-160C8.
WASHER LOCK SPRING 5/8 PLT804-022C9.
NUT HEX 5/8-11 PLT803-021C10.
HHCS 7/16-14X1 1/2 GR5802-029C11.
WASHER LOCK 7/16 PLT804-014C12.
WASHER FLAT 7/16 SAE PLT804-041C13.
BUSHING 3/4OD X 5/8ID X 1/2 LG890-598C14.
20 SER PW ARM PIVOTSPACER TB890-524C15.
NUT HEX FLANGE LOC 7/16-14 PLT803-229C16.
SPRING EXT 1 5/8 OD X 8.2807-088C17.
NUT HEX LOCK 1/4-20 FLG803-088C18.
HHCS 1/4-20X1 GR5802-005C19.
1 X 12 PRESS WHEEL RIM HALF817-330C20.
BRG .63ID PRESS WHL ASY822-170C21.
TIRE RUBBER1 X 12814-034C22.
Press Wheels
RevisionCommentsPart DescriptionPart No.Ref.
04/10/13 - 99 - 196-359P
Page 100
Table of Contents Part Number Index
1" x 12" Double "V" Press Wheel Long
(Applies to 3N-4010 & 3N-4010HDF, 3N-4020 only)
18193
196-359P - 100 - 04/10/13
Loading...