Great Plains 3000TT User Manual

Assembly Instructions for the Rolling Harrow and Board

Turbo-Till

6/26/03

Your initial action is to locate the correct drag frame [(61) 589-107H through 589-116H]. Bolt
the drag frame to the rear drag plates located on the rear of your Great Plains Turbo Till, using 5/8x1 ½
hex bolts [(43) 802-051C] with 5/8” hex nuts [(25) 803-021C] and 5/8” lock washers [(26) 804-022C].
The rolling harrow gangs shown in figure 4 will come to you partially assembled. To finish assembly,
refer to the table in figure 4 and assemble accordingly. Start by locating the correct rolling harrow tube,
center it over your partial assembly on the bearing hangers [(52) 589-142H], and mount the tube using
5/8x3x4 ½ U-bolts [(44) 806-183C] with a lock washer and nut. Your next step is to locate the ball joint
assemblies [(59) 589-064H]. Figure 4 shows you the dimensions to mount the ball joint assemblies on
the rolling harrow tube. Count the number of each assembly in figures 1-3 and assemble accordingly.

Mount the rolling harrow brackets [(60) 589-057H] to the under side of the drag frames
according to the dimensions in figures 1-3, using a 5/8x3x4 ½ U-bolt [(44) 806-183C] with a lock
washer and nut. You may tighten the U-bolts on all the brackets that are closest to the rear of the
machine. Leave the front brackets loose to slide until the rolling harrow assemblies are hung under the
frame. Use the 1x4 hex bolt and 1” nylock nut through the harrow brackets (589-057H) and ball joint
assemblies [(59) 589-064H] to hang the rolling harrow assemblies under the frame. Be careful to put the
proper gang in the proper location and be sure that the assemblies are oriented correctly as shown in
figure 4. When all gangs are hung under the frame, tighten the remaining U-bolts

Mount the rear stand bracket [(71) 580-049H], if applicable, to the drag frame with 5/8x4x4 ¼
U-bolts, a lock washer and a nut as shown on figure 1. The rear stand leg [(70) 560-196H] should be
pinned in the rear stand bracket with a 3/4x4 ½ pin and retainer (805-081C).

Mount the reel arm assemblies (589-069L) to the drag frames, using the dimensions in figures 6­10, using a 5/8x3x4 ½ U-bolt [(44) 806-183C] with a lock washer and nut. These bolts may be
tightened at this time. Mount the leveling board mounting tube (32) using a 5/8x2 1/2x3 ¾ U-bolt [(16)
UB0037] with a lock washer and nut, according to the dimensions and locations in figures 6-10. Be sure
to bolt on the correct mounting tube in the correct location. These bolts may be tightened at this time.
Use the 5/8X3 hex bolt with a lock washer and nut through the mounting tube and the leveling board
arm [(30) 589-073H] to hang the arms. Use ½x2 ½ carriage bolts [(43) 802-571C] with a ½” lock
washer and ½” nut [(41) 804-015C - (40) 803-020C] to mount the leveling board on the arms. The
leveling board part numbers will be marked on figures 6-10 to be sure the correct level board is mounted
in the correct location. Check the dimension in between the leveling boards on each section to be sure
there remains about 1” of gap in between them. If the boards are not about 1” apart, recheck the leveling
board mounting tube dimensions. There should be about 5” in-between the leveling boards between the
center section and each wing.

TURBOTILL FINISHING ATTACHMENTS

ROLLING HARROW

REF DESCRIPTION PART NO. PART NO. 1200TT 2200TT 3000TT 4000TT

NO. (KENT MFG) (GP)

ROLLING HARROW GANG ASSEMBLIES

7 WHEEL ROLLING HARROW GANG 589-065K

8 WHEEL ROLLING HARROW GANG 589-066K

9 WHEEL ROLLING HARROW GANG 589-067K 1

10 WHEEL ROLLING HARROW GANG 589-068K 2 5

11 WHEEL ROLLING HARROW GANG 589-071K 4 4

12 WHEEL ROLLING HARROW GANG 589-095K 2

13 WHEEL ROLLING HARROW GANG 589-117K 2 2

(INDIVIDUAL PARTS INCLUDED IN GANG ASSEMBLIES)

64 3/4 LONG X 1/2 TINE STOP/SPACR n/a 550-134D 6 8 12 18

63 1/2 LONG X 1/2 BOLT SPACER n/a 585-013D 6 8 12 18

50 SPIDER WHEEL LARGE n/a 589-055H 12 22 32 40

SPIDER WHEEL OFFSET @ 22.5 n/a 589-056H 14 24 32 45

SPIDER WHEEL SMALL n/a 589-094H 3469

51 BEARING, 1 1/4" SQUARE PW0115 822-209C 6 10 14 18

52 BEARING HANGER n/a 589-142H 6 10 14 18

53 SPACER - LONG n/a 589-026D 26 46 64 85

54 SPACER - SHORT n/a 589-027D 6 12 16 18

55 43 7/8 ROLLING HARROW SHAFT n/a 589-014D 0000

49 5/8 ROLLING HARROW SHAFT n/a 589-015D 0000

55 1/2 ROLLING HARROW SHAFT n/a 589-016D 1000

61 3/8 ROLLING HARROW SHAFT n/a 589-017D 2005

67 1/8 ROLLING HARROW SHAFT n/a 589-029D 0044

73 ROLLING HARROW SHAFT n/a 589-050D 0200

79 3/8 ROLLING HARROW SHAFT n/a 589-056D 0220

66 ZERK GUARD ROLLING HARROW n/a 589-085D 6 8 12 18

56 1" THREADED STUB SHAFT PW0126 800-364C 3469

57 WASHER, RECT 1/4X1" FLAT PW0116 585-057D 6 8 12 18

49 PIN, 1/2" HR RND 1 3/8" LONG PW0140 585-056D 3469

65 TREADER SHAFT 1/8" SPACER PW0427 585-066D 3469

58 48" ROLLING HARROW TUBE n/a 589-018D 0000

54" ROLLING HARROW TUBE n/a 589-019D 0000

60" ROLLING HARROW TUBE n/a 589-020D 1000

66" ROLLING HARROW TUBE n/a 589-021D 2005

72" ROLLING HARROW TUBE n/a 589-031D 0044

78" ROLLING HARROW TUBE n/a 589-049D 0200

84" ROLLING HARROW TUBE n/a 589-055D 0220

67 NUT HEX TOP LOCK 1/2-13 PLT n/a 803-342C 24 32 48 72

40 1/2" HEX NUT 3008 803-020C 3469

41 1/2" LOCK WASHER 4108 804-015C 3469

42 1/2 x 1 1/2" CARRIAGE BOLT 240824 802-106C 12 16 24 36

62 RHSNB 1/2-13X2 GR5 n/a 802-129C 12 16 24 36

45 1/2 x 2 1/2" HEX BOLT 110540 802-130C 3469

25 5/8" HEX NUT 3010 803-021C 24 40 56 72

26 5/8" LOCK WASHER 4110 804-022C 24 40 56 72

44 5/8 x 3 x 4 1/2" U-BOLT UB0029 806-183C 12 20 28 36

46 1" FLAT WASHER 4016 804-028C 6 8 12 18

47 1" LOCK WASHER 4116 804-027C 3469

48 1" NYLOCK HEX NUT 3616 803-038C 3469

ROLLING HARROW GANG MOUNTING HARDWARE

59 BALL JOINT BRACKET n/a 589-064H 6 8 12 18

60 BRACKET - ROLLING HARROW n/a 589-057H 6 8 12 18

61 DRAG FRAME 43 3/4 RH n/a 589-107H 1

DRAG FRAME 56 RH n/a 589-108H 1

DRAG FRAME 106 RH n/a 589-109H 1

DRAG FRAME 109 1/2 RH n/a 589-110H 1

DRAG FRAME 129 n/a 589-111H 1 1

DRAG FRAME 149 n/a 589-112H 1 1

DRAG FRAME 43 3/4 LH n/a 589-113H 1

DRAG FRAME 56 LH n/a 589-114H 1

DRAG FRAME 106 LH n/a 589-115H 1

DRAG FRAME 109 1/2 LH n/a 589-116H 1

36 1 x 4 HEX BOLT 111664 802-073C 6 8 12 18

48 1" NYLOCK NUT 3616 803-038C 6 8 12 18

43 5/8 x 1 1/2" HEX BOLT 111024 802-051C 16 32 40 56

25 5/8" HEX NUT 3010 803-021C 64 96 136 200

26 5/8" LOCK WASHER 4110 804-022C 64 96 136 200

44 5/8 x 3 x 4 1/2" U-BOLT UB0029 806-183C 24 32 48 72

4/20/2004

Harrow Width (Feet)

TurboTill Rolling Harrow.xls

11.7 20.6 28.7 38.1

4/20/2004

TURBOTILL FINISHING ATTACHMENTS

LEVELING BOARD FOR ROLLING HARROW

REF DESCRIPTION PART NO. PART NO. 1200TT 2200TT 3000TT 4000TT

NO. (KENT MFG) (GP)

31 4' LEVELING BOARD n/a 589-058D 4

5' LEVELING BOARD n/a 589-043D 2 6 2

6' LEVELING BOARD n/a 589-044D 2 2 2

32 36" MOUNTING TUBE n/a 589-120H 0004

48" MOUNTING TUBE n/a 589-074H 0262

56" MOUNTING TUBE n/a 589-077H 2202

30 LEVEL BOARD ARM n/a 589-073H 4 8 12 16

4 REEL ARM n/a 589-060H 4 8 12 16

6 ARM MOUNT BRKT n/a 589-059H 4 8 12 16

7 CLEVIS BOLT, 3/4" x 22 1/4" MC0078 575-516H 4 8 12 16

8 LONG SPRING DA0056 807-224C 4 8 12 16

9 SHORT SPRING PW0134 807-226C 4 8 12 16

12 EYE BOLT, 3/4 x 5 1/2 LONG MC0048 802-768C 4 8 12 16

70 REAR STAND LEG FC1606 560-196H 1111

71 REAR STAND MOUNT BRACKET PW0282 580-049H 1111

72 3/4 X 4 1/2 PIN AND RETAINER 131272 805-081C 1111

13 3/4 x 4 1/2 HEX BOLT 111272 802-192C 4 8 12 16

35 3/4 x 2 HEX BOLT 111232 802-064C 4 8 12 16

16 5/8 x 2 1/2 x 3 3/4 U-BOLT UB0037 806-182C 8 16 24 32

44 5/8 x 3 x 4 1/2 U-BOLT UB0029 806-183C 10 18 26 34

18 3/4 x 2 1/2 CLEVIS PIN 211040 805-140C 4 8 12 16

19 1/8 x 1 1/2" COTTER KEY 260224 805-225C 4 8 12 16

20 5/8 x 3 HEX BOLT 111048 802-059C 4 8 12 16

21 3/4" LOCKNUT 3112 803-026C 8 16 24 32

22 3/4" JAM NUT 3312 803-048C 12 24 36 48

24 3/4" FLAT WASHER 4012 804-024C 20 40 60 80

73 5/8" LOCK NUT 3110 803-024C 4 8 12 16

25 5/8" HEX NUT 3010 803-021C 36 68 100 132

26 5/8" LOCK WASHER 4110 804-022C 36 68 100 132

40 1/2" HEX NUT 3008 803-020C 8 16 24 32

41 1/2" LOCK WASHER 4108 804-015C 8 16 24 32

43 1/2" x 2 1/2" CARRIAGE BOLT 240840 802-571C 8 16 24 32

Board Width (Feet) 12.2 22.3 30.5 38.7

TurboTill Leveling Board.xls