Great Plains 20-CPH Operator Manual

Operators/Parts Manual

MANUFACTURING INC.

1994 20’ CPH

Coulter Tool Bar
Brace Assembly

®

Effective 3/30/04

12134

149-721M

General Information

General Information

Important Notice

Great Plains Manufacturing, Inc. provides this publica­tion “as is” without warranty of any kind, either express
or implied, while every precaution has been taken in the
preparation of this manual, Great Plains Manufacturing,
Inc. assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting
from the use of the information contained herein. Great
Plains Manufacturing, Inc. reserves the right to revise
and improve its products as it sees fit. This publication
describes the state of this product at the time of its pub
lication, and may not reflect the product at all times in the
future.

This publication, or parts thereof, may not be repro­duced in any form, by any method, for any purpose
without written permission from Great Plains Manufac­turing, Inc.

This Operator’s Manual applies to:

149-169A 20’ CPH Coulter Tool Bar Brace Assembly

Great Plains Manufacturing, Inc. Trademarks
The following are registered trademarks of Great Plains

Manufacturing, Inc. Great Plains, Land Pride, Applica­tion Systems, MeterCone, and Whirlfilter.

Printed in the United States of America.
For your convenience, record the information listed in

the spaces provided below. Have this information before
you when calling Great Plains Manufacturing, Inc.

-

Owner’s Information

Name:______________________________________
Address_____________________________________
City _______________ State ____Zip
Phone _____________ _________

Name of Dealership ___________________________
Dealer’s Name _______________________________
Address ____________________________________
City _______________ State ____ Zip
Phone_____________ _________
Date Purchased _____ _________

Great Plains Manufacturing, Inc.

1994 20’ CPH Coulter Tool Bar Brace Assembly 149-721M 3/31/04Great Plains Mfg., Inc.

Using this Manual

Table of Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Section 2 Assembly Instructions & Set-Up . . . . . . 2

Torque Values Chart. . . . . . . . . . . . . . . . . . . . . . . 2

Pre-Assembly Checklist . . . . . . . . . . . . . . . . . . . . 3

Introduction

This manual has been prepared to instruct you in the
safe and efficient operation of your 1994 20’ CPH

Coulter Tool Bar Brace Assembly. Read and follow all

instructions and safety precautions carefully.
The parts on your 1994 20’ CPH Coulter Tool Bar Brace

Assembly have been specially designed and should

only be replaced with genuine Great Plains parts. There­fore; should your Coulter Tool Bar Brace Assembly
require replacement parts, go to your Great Plains
Dealer.

The right hand and left hand as used throughout this
manual is determined by facing in the direction the ma­chine will travel when in use unless otherwise stated.

Product Overview

The Great Plains Coulter Tool Bar Brace Assembly is
designed to enhance the performance of your Center
Pivot Hitch in extremely hard soil conditions by reducing
the upward flex on the ends of the 20’ coulter tool bars
,thus giving better coulter depth control.

Assembling The Coulter Tool Bar Brace

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Post-Assembly Checklist . . . . . . . . . . . . . . . . . . . 3

Section 3 Basic Operation . . . . . . . . . . . . . . . . . . . 3

Section 4 Parts Book . . . . . . . . . . . . . . . . . . . . . . . . 4

Coulter Tool Bar Brace Assembly . . . . . . . . . . . . 4

symbol, be alert and carefully read the message that fol­lows it. In addition to design and configuration of
equipment; hazard control and accident prevention are
dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation,
transport, maintenance and storage of equipment.

Watch for the following safety notations throughout
your Operators Manual and on your Center Pivot
Hitch:

!

Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury. This signal
word is limited to the most extreme situations.

Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

DANGER!

!

WARNING!

This assembly is not needed and will not fit on a CPH
with the coulter tool bar weight brackets assembled on
the end of the coulter tool bars.

!

The SAFETY ALERT SYMBOL indicates that there is a
potential hazard to personal safety involved and extra
safety precautions must be taken. When you see this

Using this Manual

Included with your 1994 20’ CPH Coulter Tool Bar Brace

Assembly are the Operator’s and the Parts Manual.

For your safety and to help in developing a better under­standing of your equipment we highly recommend that
you read the operator sections of this manual. Reading
these sections not only provides valuable training but

3/31/04 Great Plains Mfg., Inc.

!

Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may also
be used to alert against unsafe practices.

also familiarizes you with helpful information and its lo­cation. The parts sections are for reference only and
don’t require cover to cover reading. After reviewing the
manuals store them in a dry, easily accessible location
for your future reference.

1994 20’ CPH Coulter Tool Bar Brace Assembly 149-721M

CAUTION!

NOTE: Indicates a special point of information which
requires your attention.

-1