Gravity Measurement CCT10, CCT20 User And Service Manual

COUNTING SCALE User and Service Manual

Please read this manual carefully before operation

----General Precautions

----Operating condition and other attentions

----Warranty

Model: CCT10/CCT20

GRAVITY MEASUREMENT, INC.

CCT10/CCT20 USER MANUAL

2

Important Safety Information

READ ALL INSTRUCTIONS BEFORE USING SCALES TO ENSURE MAXIMUM
SAFETY, BEST PERFORMANCE, AND TO GAIN KNOWLEDGE OF OUR SCALE, IT
IS ESSENTIAL THAT YOU OR ANY OTHER OPERATOR OF THE SCALE READ AND
UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE
DEVICE.

When using an electrical device, basic precautions should always be followed,

including the following:

1. Please use only the original power cord or DC adapter supplied with the scale.
Other cords or adapters may damage the scale.

2. DC adaptor is used to charge the battery, and scale can operate without DC
adaptor.

3. Avoid using long power extension cords – this may cause interference

4. Do not use on surfaces or in areas where vibration, air movement or temperature
change. Do not place in direct sunlight or near air conditioning vents.

5. Avoid high humidity (greater than 80%) that might cause condensation, and keep
away from direct contact with water and other corrosive chemicals.

6. Static may influence the weighing result. To reduce the static, wipe the pan and sc
ale with anti‐static wipes.

7. Don’t impact or drop heavy objects on the scale – this may affect accuracy, or
cause damage. Do not stack material on the scale when it is not in use.

8. Battery should be removed if the scale is not used for a long period of time.
Battery should be recharged every 3 months.

9. Place items to be weighed as close to center of the pan as possible

10. Only use fingers to operate the keypad. Do not press with hard or sharp objects.

CCT10/CCT20 USER MANUAL

3

Warranty

Gravity Measurement, Inc. (Schenectady, New York) offers one-year limited
warranty (parts and labor) for the components failed due to defects in materials or
workmanship. Warranty starts from the date of delivery.

During the warranty period, should any repairs be necessary, the purchaser must
inform its supplier or Gravity Measurement. The company or its authorized technician
reserves the right to repair or replace the components at any of its workshops depending
on the severity of the problems. However, any freight involved in sending the faulty units
or parts to the service center should be borne by the purchaser.

The warranty will cease to operate if the equipment is not returned in the original
packaging and with correct documentation for a claim to be processed. All claims are at
the sole discretion of Gravity Measurement.

This warranty does not cover equipment where defects or poor performance is due
to misuse, accidental damage, exposure to radioactive or corrosive materials,
negligence, faulty installation, unauthorized modifications or attempted repair or failure to
observe the requirements and recommendations as given in this User Manual.
Additionally, rechargeable batteries (where supplied) are not covered under warranty.

Repairs carried out under the warranty does not extend the warranty period.
Components removed during the warranty repairs become the company property.

CCT10/CCT20 USER MANUAL

4

What is inside Box

AC/DC adaptor (110V)
Counting scale CCT 10/20 Scale, with adhesive film covered platter. Two parts are separated to
protect the load cell during transportation.
Two wire seals. The wire seal is used usually by the inspector of Department of Weight and
Measure or authorized dealer. The wire seal is threaded through a metal rode that protrudes
through the bottom of the device and also through a hole in the scale base adjacent to the metal
rode.

Set up the Scale

Place the scale on a stable, level surface out of the way of air currents. The scale must
be level during use. Adjust the feet and use the integrated bubble at the front of the scale
to achieve level. Be sure that scale does not rock back and forth. Ensure no weight is on
the pan when turning on the scale. Scale is operated using the rechargeable battery. AC
adaptor is used to charge the battery, and scale can operate without DC adaptor.

LCD Display

CCT10

Size: 77 mm x 27 mm X 2.8 mm
Font height: 16 mm

CCT10/CCT20 USER MANUAL

5

CCT20

Size: 80 mm x 71 mm X 2.8 mm,
Font height: 16 mm

CCT10/CCT20 USER MANUAL

6

Control Panel

P2

UNITS

Z

T

COUNT

SAMPLE

COUNT
ALARM

M +

M R

C E

P1

P2

PCS WT

MEM

8 3 2

5 4 6

7

1 . 9

0

M01 M21

M02 M22

M03 M23

M04 M24

M05 M25

M01 M26

M07 M27

M08 M28

M09 M29

M10 M30

M11 M31

M12 M32

M14 M34

M15 M35

M01 M36

M17 M37

M18 M38

M19 M39

M20 M40

M13 M33