Graupner and KG 33565 User Manual

Graupner GmbH & Co. KG Henriettenstraße 94 – 96 D-73230 Kirchheim/Teck Germany www.graupner.de

Änderungen sowie Liefermöglichkeiten vorbehalten. Lieferung durch den Fachhandel. Bezugsquellen werden nachgewiesen. Für Druckfehler kann keine Haftung übernommen werden.

Speciﬁ cations and availability subject to change. Supplied through specialist model shops only. We will gladly inform you of your nearest supplier. We accept no liability for printing errors.

Sous réserve de modiﬁ cations et de possibilité de livraison. Livraison uniquement au travers de maga- sins spécialisés en modélisme. Nous pourrons vous communiquer l’adresse de votre revendeur le plus proche. Nous ne sommes pas responsables d’éventuelles erreurs d’impression.

Manual

33565 Receiver GR-12SH+ HoTT 33566 Receiver GR-12SC+ HoTT

CONTENTS:

1. General Note ..............................................................................................................01

2. Functions ....................................................................................................................01

2.1. Binding ......................................................................................................................... 01

2.2. Fail-Safe Function ........................................................................................................ 02

3. Receiver ...................................................................................................................... 0 2

3.1. Connections ................................................................................................................. 02

3.2. Programming ............................................................................................................... 02

3.3. Operation .....................................................................................................................02

4. Firmware Update ........................................................................................................04

4.1. Update Procedure ........................................................................................................ 05

5. Declaration of Conformity .........................................................................................07

6. Warranty ..................................................................................................................... 09

Con riserva di variazione delle speciﬁ che e disponibilità del prodotto. Fornitura attraverso rivenditori specializzati.Saremmo lieti di potervi indicare il punto vendita più vicino a voi. Si declina qualsiasi responsabilità per errori di stampa.

EN V1.0 PN.QH-01

Manual V1.0

Revision: August 2012

GRAUPNER GmbH & Co. KG – Postfach 1242 – 73230 Kirchheim/Teck – www.graupner.de

Thank you for purchasing the receiver GR-12SH+ or SC+ for the Graupner HoTT 2.4 System. Please read

Federal Communication Commission Interference Statement： This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4) Consult the dealer or an experienced radio/TV technician for help..

FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Important Note: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. This device is going to be operated in 2404~2479GHz frequency range, it is restricted in outdoor environment only.

User Manual of The End Product: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radiofrequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual.

Label and manual requirements for the End Product: For an end product using this module,there must be a label containing, at least, the following information. FCC ID certification number for model : 33566 This device contains FCC ID : ZKZ-33566 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC.Where the 33566 will be installed in final products larger than 8cm × 10cm following statements has to be placed onto the device . "Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation."

Assure Compliance: The use of the modular transmitter is only approved to be used inside the specified equipment which compliance with all the instruction was subjected. We assure the compliance of the end product when it is assembled inside the specified equipment.

FCC Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Antenna: This device shall only be used with the tested antenna and separate approval is required for all other operating configurations.

OEM Integrator Manual

through this entire manual before you attempt the installation and usage of your Graupner HoTT 2.4 System!

These operating instructions are part of this product. They contains important notes to the operation and handling. Please take this into consideration when you pass on the product to third parties. Neglect of the operating instructions and the safety instructions lead to expiring the warranty. Graupner constantly work on the advancement of all remote control systems; changes of the scope of delivery in form, technology and equipment we must reserve ourselves therefore. Please have understanding for the fact that from data and illustrations of this operating instructions no requirements can be derived.

Please keep these instructions for further reference!

Intended use

The receiver is speciﬁ cally designed for slow-ﬂ y models whose components are ﬁ tted with SH or ZH connec- tors. The maximum range is around 300 m, which is appropriate to this type of model. The receiver must not be used in any model which requires greater range, or whose servos draw a current which exceeds the maximum permissible for SH connectors (#33565 max. 0.5 A) or ZH connectors (#33566 max. 1 A). This product works with any Graupner HoTT 2.4 GHz transmitter, but with no others. If you do not own a Graupner HoTT 2.4 system, the receiver will not function. This product is not compatible with any other 2.4 GHz radio control system. It is not suitable for young people under fourteen years. If a young person below that age wishes to use it, he or she must be supervised by an adult. Before using the receiver for the ﬁ rst time, please read and observe all the warnings and safety notes in these instructions and on the packaging.

WARNINGS

If several independent models / receivers are operated close together - e.g. for glider towing - the receivers • must be kept a minimum of 50 cm apart, otherwise there is a danger of interaction between them. For the same reason the pilots on the ground should stand at least 5 m apart.

1. GENERAL NOTE

When switching on or adjusting the radio control system it is essential to keep the transmitter aerial at least 15 cm away from the receiver aerials at all times. If the transmitter aerial is too close to the receiver aerials, the receiver will be overloaded, causing the red LED starts ﬂ ashing. The transmitter responds by emitting a beep once every second; the red LED also goes out. The radio control system is now in Fail-Safe mode. If this should occur, simply increase the distance between the aerials until the audible warning signal ceases, and the red LED on the transmitter lights up again; at the same time the red LED on the receiver should go out.

2. FUNCTIONS

2.1. Binding

When you wish to use the Graupner HoTT 2.4 GHz receiver with a particular transmitter, the ﬁ rst step must always be to “bind” the unit to “its” Graupner HoTT 2.4 GHz RF module (transmitter). This “binding” procedure only needs to be carried out once for each combination of receiver and RF module. The units supplied in the set are already bound to each other at the factory, i.e. the binding procedure described in the following section only needs to be carried out when you wish to use an additional receiver. However, it can also be repeated at any time if required, e.g. after changing transmitters. Please refer to the „BINDING“ section in your RC system

or module instructions for the procedure.

When binding is required, this is the procedure:

• Switch the transmitter and receiver on. Unless the receiver has already been bound to the transmitter, it automatically enters BIND mode when • initially switched on. If you have already completed the binding procedure for this combination of transmitter and receiver, the red LED on the receiver goes out, and the model can be operated immediately. If the LED does not go out, please follow this procedure:

• Transmitter with HoTT module: locate the BIND / RANGE button on the back of the transmitter, and hold it pressed in while you press and hold the SET button on the receiver. Both LEDs on the back of the trans-

Do not connect servos to this receiver whose current drain exceeds the maximum permissible for•

SH connectors (#33565 max. 0.5 A) or ZH connectors (#33566 max. 1 A).

If channel 1 is used as an electronic speed controller, the continuous current of the motor connec-•

ted to it must never exceed 2 A, otherwise the receiver could be ruined!

01 Manual Graupner HoTT 2.4

________________________________________________________________________

Manual Graupner HoTT 2.4 10

+ 4 hidden pages

Graupner and KG 33565 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual