GRAUPNER 16007500 User Manual

P1

mz-8H HoTT

◎ GRAUPNER 8th F, 202 Dong, Chunui Techno-Park II, 202,Chunui- Dong, Wonmi-Gu, Bucheon-Si, Gyeonggi-do, SOUTH KOREA. TEL: 070-7863-3675 FAX : 070-7863-3670 E-mail: service@openhobby.com

FUNCTION

Main function and Channel Basic 4 Channels and added 6 Channels. 6 Channel is as below.

① LED : ON / OFF

-> CH8 1100us / 1900us

② SPEED : Attitude mode / Rate mode

-> CH5 1100us / 1900us

③ SNAP : Taking pictures

-> CH9 1100us (1500us nothing)

④ RECORD : Film movies

-> CH9 1900us

⑤ FLIP : Use the button on top left of image (360° FLIP)

-> CH10 1100us / 1900us now channel 10, later channel 7, (Alpha 150 not active in autopilot mode as soon as GPS is connected it will be channel 6 coming home function)

⑥ 3D / EASY : Use the button on top right of image

(180° revolution and additional function)

-> CH6 1100us / 1900us CH6, when AKRO3D is adjusted in the receiver, for normal flight mode with GPS (Alpha 150) it will be autopilot function

⑦ 2.4GHz Quad with 6-Axis Gyro

⑧ You can check real time flight screen with FPV Camera and 5.8GHz RF. And you can monitor with Goggle and other monitors.

⑨ You can attach camera and video module by choosing option. You can take a video on the radio using Photo & Video button.

mz-8

Frequency band 2404.056MHz ~2479.095 MHz Modulation FHSS Transmission output about 1mW Temperature range -10 … +55 ℃ Antenna Monopole Antenna Battery AA Size x 3 pcs Operating voltage 3.6 … 4.8V Output voltage about 50mA Dimension 151 x 134 x 63.7 mm Weight about 260g (Incl. battery)

P2

f you push Flip button, buzzer will ring with 0.5 seconds

push Flip button and when

ging, move stick of transmitter to

hen you push 3D button, buzzer will ring twice with 1

T

Light

Button

hen you push Function button, one short sound rings.

control of general quad copters.

hen you push Function button, two short sound rings.

ou can do rotation and normal flight on 3D flight mode

transmitter. Function is same with 3D helicopter.

Power Switch

MZ

-8

Camera Record Button

Camera Snep

Transmitter manual

Operating transmitter

- Power on : Pull Slide switch up

- Power off : Pull Slide switch down

1) Flip Function

I intervals. To rotate a full 360 degrees, buzzer starts rin maximum position quickly.

2) 3D & Easy Function

W second intervals. 3D function is for 180 degrees flight. same function with Flip.

Flip Button

o operate, use

3) Attitude Function

W This function is attitude

4) Rate Function

W Y with

3D / Easy Button

Trim

Status & Function

Trim

P3

< LED arrangement of transmitter >

stay OFF

When the lights are on, LED stay ON condition.

stay ON condition.

blinks with one second intervals.

ptional feature

condition.

default status

When movie button is pressed, LED blinks with one

and Transmitter status function.

）

nd, LED blinks with 0.5 second

condition

Red LED

blinking (1s)

fast blinking

slow blinking

1 blink

2 blink

3 blink

(3times)

LED Function

1) LIGHT ON / OFF Function

Yellow Led ① When the lights are off, LED ② （default status）

2) SPEED Attitude and Rate Function

Red Led

① Attitude mode : LED

status）

② Rate mode : LED

condition.

（default

Status Discription

Bind status (No

bind)

Bind Success,

Bind range

RX receive OK

Range Test

Low Voltage

Sensor Warring

Rx Voltage,

Error

Normal mode

Temp Error

Receive rate low,

No RX

Factory Error

Trim inc/dec

Trim 0%

Green LED Buzzer

on

low beep(1)

low beep(2)

High beep(4)

High beep(3)

High beep(2)

High beep(1)

Low beep(1)

low beep(1)

High beep(1)

/2sec

/click

3) Camera function （O

Green Led ① When power is switched on, stay On

--> Photograph mode （ ②

second intervals.

--> Video mode

4) Binding

Red Led （Status Led

① Show Power and Binding

② If device is not bou intervals. ③ If device is bound, LED stay ON

）

.

Program mode

start

Program mode

Program

mode

Stick

Calibration

exit

Servo Reverse

(Normal)

Servo Reverse

(Reverse)

ATV 100%

Fail Safe mode

start

Fail safe (trim dn,

hold)

Fail safe (trim up,

fail)

Calibration mode

start

Stick move done

Dead range set

1 blink

(5times)

2 blink

(5times)

1 blink

(5times)

2 blink

(5times)

3 blink

(3times)

Dead

blink/3sec

low beep(1)

low beep(2)

High beep(1)

low beep(2)

low beep(1)

High beep(1)

low beep(2)

P4

he last used memory will be bound

In case of No Receiver connection, if you press the

it will search Receiver.

is not searched, it will be repeated until

Receiver, and you can bind with new Receiver by

In case of no having receiver, which is already saved in

memory, then you can bind with new receiver by

If Receive Signal is normal, RED LED wi

In case of Waiting Receiver or Range warning, RED

Press shortly button of

fter Binding with Receiver, if you shortly press this

functional Switch, Range Test mode will operate for

While operating Range mode, if you shortly press this

t Range mode operation, RED LED will blink quickly

occurred

RED LED indicate State)

At under 3200V, Warning will be announced and at

While Binding, Transmitter should always have distance

ave.

Otherwise, it might be connected to Return channel, and

workable only at Binding condition

Condition of Basic Operation

simultaneously for a second.

Program mode : Red Led

once per a second interval

Data could be saved.

Servo End

case of Stick Calibration, Default will

value, Customer can adjust trim as below

> 1100us ~ 1900us

on of Stick,

0% ~ 100%

f move to 100% position, High Beep sound will be

Red Led will be blinked once per a second interval

once per a second interval

when change Servo direction.

are on neutral pos

tion.

f press Power switch with pressed trim switch to Max. or

Min. position, Normal mode and Reverse mode will be

i

once per a second interval

Normal mode : Green LED will be blinked once per a

Program Mode

(

)

Normal Mode (1) Basic Operation

- When Power on, t Receiver.

- button of left stick for 1sec,

- if Receiver

pressing BIND/LED Switch.

(2) BIND mode

pressing BIND Switch.

LED will be slow blinked.

(3) Range Test mode

Functional switch: SNAP once. A

to

find

ll be turned On.

SPEED +

(1)

Enter to Program mode simultaneously for 2sec.

Release Program mode

Indication of once per a second interval

.

Program mode : Blink

(2) Saving Data

50pcs of last used

(3) Adjustment of

In

- 100% -- At Max. or Min. Positi Range of Trim is available I occurred once.

-

: Press two Stick Switch

will be blinked

Position

be 100%. At this

way.

adjust Trim Switch

~ 150%.

90sec.

switch, Range test mode will be ended. A and make buzzer sound. After 90sec, Beep sound will be enter to Main Mode.

(4) Low Battery Voltage warning

RED LED will do fast blinking. (

3300V, warning will be removed. 3Cell Alkaline Battery will be used.

Important Point :

from the Receiver. At least 1m should h

one time, and

Program mode : Blink

(4) Servo Reverse Set

This is used All sticks switch to Max. or Min. Posi I

changed.

- Indication of Servo Rece blinked

- second interval.

ition, and move the trim

ver mode : Red Led will be

do malfunction.

P5

Green LED will be blinked

once per a second interval

Reverse mode : Blink twice per a second interval

stick switch for a second at Program mode.

per channels and select Fail pos mode

condition will be

stick switch for a second, Fail safe setting

LED will be blinked

If Trim is UP, it is a Fail safe mode, and

ce per a second interval.

Green LED will be blinked once per a second interval.

Blink twice per a

once per a second interval (

Blink twice per a second interval (

Stick Calibration Mode

, in state of

f enter to Mode, RED LED will blink 3 times.

: Blink 3 times per a second

Move all sticks from side to Side and

fter operated last stick, hold it to middle position for

Red and Green LED will blink 3Times at

Blink 3 Times per a second interv

after that, it is moved to Dead Range set mode

position

Dead range set about Neutral position, is set by trim

from 1 to 6 steps.

, there is no spring, Do not set.

only set for CH2, CH3, CH4

Green LED will blink depends on Neutral set steps.

or example, if you set Dead range to 6%, LED will

s per a second interval.

Blink 3times per a sec interval.

Blinks depends of setting value

f set is done, press left stick button for 2 sec.

How to do Stick Calibration

-Reverse mode : second interval.

Program mode : Blink

Normal mode : Blink (Repetition 5times)

(Repetition 5times)

(5) Fail Safe Set

Press right Press trim button and Hold it. Whenever press Trim button, Setting- transferred to Receiver.

twice per a

(1) Enter to

Turn On the Radio I

Stick calibration mode interval

(2) Set Stick Calibration

position. A 3Seconds. If Set is done, same time.

Stick calibration mode

pressing left stick switch.

back to middle

Stick move done

al If press right- mode will be ended.

- Indication of Fail Safe mode : RED twice per a second interval.

- Pos mode : Green LED will be blinked twi (Repetition 5times)

- Hold mode : If Trim is Down, it is a

(Repetition 5times)

Program mode (Failsafe mode): second interval

Hold mode : Blink

Hold mode, and

Repetition

※ automatically.

(3) Dead range set

This is for keep Neutral accurate Neutral value.

switch up and down. It can be settable ※ in case of Throttle CH1 (

F blink 4time

Dead range mode

, in case of they have no

( 0, 2, 4, 6, 8, 10% )

)

5times) Pos mode : 5times)

Repetition

Dead range set

I

(6 steps)

P6

안안안안

(1) KC 인증

Graupner mz-8 Transmitter

KCC

인인인인

: MSIP-CRM-sjr-16007500

(2)

Conformite Europeenne

Product(s): Graupner mz-8 Transmitter,

(3) FCC Information

Graupner mz-8 Transmitter

FCC ID: SNL-16007500

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

• NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- _Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

• FCC radiation exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

◎

Notes on environmental protection

This symbol on the product, user manual or packaging indicates that this product must not be disposed of with other household waste at the end of its life. It must be handed over to the applicable collection point for the

recycling of electrical and electronic equipment. The materials are recyclable as marked. By recycling, material reusing or other forms of scrap usage you are making an important contribution to environmental protection. Batteries and accumulators must be removed from the device and disposed of at an appropriate collection point. Please inquire if necessary from the local authority for the appropriate disposal site.