Grange Romana Arbour, ROMARB Assembly Instructions Manual

D

E E E E E

B

FF

A

A

C

CARE OF YOUR ARBOUR

The Romana Arbour is made of planed pressure treated and FSC certified timber
and as such is guaranteed against rot for a minimum of 15 years. However, it
should be remembered that as a natural product, timber is subject to movement
and weathering as it seasons. It is not uncommon for small spits to occur when
drying and warping when timber is allowed to dry too rapidly. These will normally
go back when humidity rises, it is nature at work and not considered a fault.

AFTERCARE

Its colour will also change with time, A re-treatment, as required with a proprietary wood treatment is recommended.

S

IDE SECTIONS

S

EAT BACK

SEAT

ROOF BEAMS

R

OOF RAFTERS

SUPPORT STRUTS

A

D

E

B

C

F

ROMARB - 192cm [H] x 180cm [W] x 87cm [D]

ROMANA ARBOUR

Self-Assembly required Home Delivery available Pre-Painted available

www.grangefen.co.uk

All products and related emblems featured are
trademarks of Grange Fencing Ltd.

©2015 Grange Fencing Ltd All rights reserved.
In line with the Company’s policy of
continuous product development, the right
is reserved to change and improve product
design without prior notice.

CODE: ROMARB

PLAN

192cm

180cm

87cm

192cm

post length:
180cm

Romana Arbour [A5 4pg instructions] 10/3/17 10:07 Page 1

BEFORE YOU START

When you are ready to start make
s

ur

e y

ou have the right tools to
hand, plenty of space and a clean
dry area for assembly.

Drill pilot holes to aid assembly.

I

t is advisable for two people to

carry out the work

Please check the packs and make
sure that you have all of the parts
listed above. If not, contact your
r

etailer who will be able to help you.

T

hank you for choosing this garden structure from Grange. In order to gain the most

benefit from it please read the following instructions carefully.

T

OOLS REQUIRED(Not Supplied)

POWER DRILL/SCREWDRIVER
w

ith posidrive No.2 bit

3

mm DRILL FOR PILOT HOLES

TAPE MEASURE

P

ARTS LIST

SIDE SECTIONS x 2

SEAT BACK x 1

SEAT x 1

ROOF BEAMS x 2

ROOF RAFTERS x 5

SUPPORT STRUTS x 2

HARDWARE PACK

SCREWS - 4mm x 6cm csk x18

SCREWS - 2.5mm x 5cm csk x10

A

w

y

w

y

D

E

Fig.1.

Fig.2.

ASSEMBLY

S

TEP 1

Assemble the seat (B+C) using screws
a

s shown in Fig.1

.

STEP 2

L

ay one of the Side Assemblies (A)on a
clean flat area and attach the seat to the
s

ide assembly using screws [

w]

. The seat
should be positioned approximately
45cm from the bottom of the posts as

F

ig.2

.

STEP 3

Turn the assembly onto the Seat Back (B)
so that the second side may be attached
t

o the other end of the seat assembly.

Ensure the seat height is the same on
both sides.

STEP 4

Stand the assembly upright with care.

STEP 5

Take the two Curved Beams (D)and
mark the positions for the Rafter (E).
Start at the centre of the beams and
mark two equally spaced positions either
side of centre as

Fig.3.

STEP 6

Fit the curved roof beams to the top of
the posts ensuring that the overhang at
each end is the same using screws [

w] as

Fig.4.

STEP 7

The Rafters (E) should now be fitted at
the positions marked on the beams using
screws [y].

STEP 8

Finally fix the Struts (F) at the front of the
arbour between the post and underside
of the seat using screws as

Fig.5.

B

C

F

A

B

C

D

E

F

Fig.3.

w

ww

w
w

w

w

y

y

y

y

y

y

y

y

45cm

w

B

C

C

D

D

A

E

A

Fig.4.

Fig.5.

C

F

A

Romana Arbour [A5 4pg instructions] 10/3/17 10:07 Page 2