Page 1
Quick Installation Guide
5-Port Gigabit PoE+ Switch (30W)
Table of Contents
Introduction …………………………………………………..
Power Over Ethernet (PoE) & Features ……..…………..
Unpacking and Installation ……… .………………………..
System Requirement……. .………………………………..
Front Panel /LED….………………………………………….
Hardware Installation… …………. …………….……….…..
Technical Specication……………………………………....
Troubleshooting ………...……………..……..……………...
Page 2
Page 2
Page 3
Page 3
Page 4
Page 5
Page 6
Page 7
FCC Warning:
This device has been tested and found to comply with the regulations for Class B digital equipment.
Pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with users guide, may cause harmful interference to radio communications. Operation of this device in
a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his/her own expense.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
UL Warning:
1> Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater then room ambient. Therefore,
Consideration should be given to installing the equipment in an environment compatible with
manufacturer’s maximum rated ambient temperature
2> Reduced Air ow-installation of equipment in a rack should be such that the amount of air ow required
for safe operation of the equipment is not compromised.
3> Mechanical Loading- mounting of the equipment in the rack should be such that a hazardous
condition is not achieved due to uneven mechanical loading.
Important
This user guide contains information on the limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. Read the entire guide carefully
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 1 OF 7
Page 2
1. Introduction
2. Power over Ethernet (PoE) & Features
The 5-Port Gigabit PoE+ Switch is an unmanaged Gigabit Ethernet PoE+ switch designed to enhance workgroup
performance while providing a high level of exibility. It provides 5 x 10/100/1000Mbps ports and 4 IEEE802.3at
Power over Ethernet (PoE+) ports for workstation, It is an ideal solution for small oce and home users to utilize a
combination of Gigabit PoE and non-PoE device. The switch automatically detects IEEE 802.3at compliant devices
and provides power and data over a single cable.
The 5-Port Gigabit PoE switch is a PSE (Power Source Equipment) and fully compatible with PDs (Powered Devices)
that comply with the IEEE 802.3at PoE+ standard. The 5-Port Gigabit PoE Switch enables users to attach IEEE802.3at
compliant devices such as wireless Access Points (WAP), VOIP phones, IP cameras, printers and Network Attached
Storage (NAS) directly to the 5-Port Gigabit Ethernet PoE Switch without requiring additional power to the
device. The unit is designed for home and small business users in mind and is ideal for installations where AC
power is not available or not cost-eective.
No conguration is required and installation is quick and easy. Support for Auto – MDI / MDI-X on all the ports
eliminate the need for crossover connection to another switch or HUB. Auto - Negotiation on each port senses the
link speed of a network device ( either10/100/1000 Mbps) and intelligently adjusts for compatibility and optimal
performance.
* 1-Year Limited Warranty for switch and 1-Year Limited Warranty for the power adaptor are available
* This device is designed for indoor use. Do not use outdoors.
Power Over Ethernet (PoE):
Power over Ethernet (PoE & PoE+) integrates 55V power and data onto one single cable, eliminating
the need to have AC power available at all device locations. Power and Data are integrated
onto the same cable, supporting category 5/5e/6 up to 100 Meters. PoE provides power to
PoE compatible devices, such as VOIP telephones, wireless access points (WAP), and IP security
cameras. PoE devices are already in the market, saving up to 50% of overall installation cost by
eliminating the need to install separate electrical wiring and power outlets.
Features:
•5 x 10/100/1000Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 4-Port PoE+ ( port 1 ~ port 4)
•Compliant with IEEE 802.3at
•Supports PoE power up to 104W (at) for all PoE ports.
•Supports PoE IEEE802.3at compliant Powered Device (PD)
•Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
•Full/half duplex transfer mode for each port.
• Wire speed reception and transmission.
•Up to 2K unicast address entities per device. Self-learning, and table aging.
•9216-byte jumbo packet length.
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 2 OF 7
Page 3
3. Unpacking and Installation
Open the container and carefully unpack its contents.
The case should contain the following items:
• One 5-Port Gigabit Ethernet PoE+ Switch
• One AC to DC Power Adapter
• Quick Installation Guide.
*If any item is found missing or damaged, please contact your local reseller for replacement.
4. System Requirements
• Installation:
The installation of the 5-Port Gigabit Ethernet PoE+ Switch requires the following steps:
• A computer with a 10/100/1000Base-T network adapter installed
• The surface must support at least 3.0 kg (6.6 lbs) for the switch.
• The power adapter should be within 1.5 meters (5 feet) of the switch
• Visually inspect the power cord and make sure that it is fully secured to the power outlet.
• Make sure that there is proper heat dissapation and adequate ventilation around the switch.
Do not place any heavy objects on the switch.
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 3 OF 7
Page 4
5. Front Panel/LED/PoE Network
Front Panel
Power
LED Display
Light
Power LED
Speed (1 - 5)
Act/Link (1 - 5)
PoE+ (1 - 4)
Blinking Slowly Inactive Blinking Fast☼
Interface Ports
Port 1-4 PoE+
Port 5 Uplink
Uplink Port
PoE
Act/Link
PoE Ports
Speed
LED on: Power ON / LED o: Power OFF.
☼
: 100 Mbps
: Link in full duplex mode and no activity
☼
: Link in half duplex mode and no activity
: Link for 10 Mbps : 1000 Mbps
: Activity
: Link Down
LED on: The PoE device is connected and the port is supplying power.
LED o: No PoE device is connected.
10/100/1000 Mbps Ethernet PoE Port 1 - Port 4 , 8P8C RJ45
10/100/1000 Mbps Data UpLink 8P8C RJ45
Rear Panel
1
2
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 4 OF 7
DC Power Input Jack. DC Input 55VDC. OD 5.5mm/2.5mm
Power ON / OFF switch.
Page 5
6. Hardware Installation
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 5 OF 7
A. Power: Connect the AC Power cord to the power source and the DC power cord to the switch.
B. Up-Link: Connect a CAT-5, 5e or 6 RJ-45 network cable from the Network or Router to an
Up-Link port.
Setting Up Your Network
Page 6
7. Technical Specications
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 6 OF 7
Standard
Protocol
Network Cables
Number of Ports
PoE power on RJ-45
AC to DC power supply
Power Consumption
Temperature
Humidity
Dimensions
EMI
Safety
Filtering Address Table
MAC address Learning
Transmission Method
Packet Filtering
Forwarding Rate
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3x Full Duplex Flow Control
IEEE 802.3at Power over Ethernet Plus (30w)
IEEE 802.3ab 1000Base-T Gigabit Ethernet (twisted-pair copper)
CSMA/CD
Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex)
Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex)
Gigabit Ethernet: 2000Mbps (full duplex)
10Base-T: 2-pair UTP Cat 3, 4, 5 up to 100 meters.
100Base-T : 2-pair UTP Cat 5, 5e up to 100 meters.
1000Base-T: 4-pair UTP Cat5e 6, up to 100meters.
5 x 10/100/1000Mbps auto-MDIX RJ-45 ports with 4 PoE enabled ports.
Power +: pin 3 & pin 6 ; Power –: pin 1 & pin 2
Input: 100V ~ 240VAC, 50Hz ~ 60Hz. Output: 55VDC 2A
6.0 watts ( max with no PD device connected)
104watts ( 4 PoE ports 30W/port)
Operation: 0˚C ~ 40˚C or 32˚F ~ 104˚F
Storage Temperature: -10˚C ~ 70˚C or 14˚F ~ 158˚F
Relative Humidity: 5% - 95%
151 mm W x 126 mm D x 36 mm H
FCC Class B, CE Mark Class B
100VAC to 240VAC power supply UL listed.
Automatic update
Store – and – Forward
10Mbps Ethernet: 14,880/pps
100Mbps Ethernet: 148,800/pps
1000MBase-T Ethernet: 1,488,000/pps.
Page 7
8. Troubleshooting
1> After connecting the Switch to a power outlet, the LEDs do not turn on.
Check the connection of the power cord to the Router and the power outlet.
Check that the power outlet is active.
2> When I connect a computer to the Switch's port, the Link/ACT LED turns on, but
the 1000 LED remains o.
When the 1000 LED is o, the computer's connection speed is 10Mbps or 100Mbps.
3> After I connect my PCs to the Switch, I am unable to share les.
1. Check the LEDs on the Switch. Make sure the Link/ACT LED is on.
2. Check the network cable. The minimum length of the cable is 1.5 meters and the
maximum length of the cable is 100 meters.
3. Disable any software rewall program.
4. Verify that you have le sharing enabled. Please contact your Operating System
support for more information.
4> After I connect my PCs to the Switch, I can only get onto the Internet from one
computer.
The Switch is not designed to share Internet between multiple computers. You need to
add an Internet router.
5> Where is the uplink port located on the Switch?
Since all the ports on the Switch are Auto-MDIX, any of the ports can be used as an
uplink port. If you still encounter problems or have any questions regarding the 5-Ports
Gigabit PoE switch please contact supplier’s Technical support department.
5-Port Ethernet Gigabit PoE Switch Rev 1.0 01/03/2013 Page 7 OF 7
Loading...