GrandTec Joymate Quick Installation Manual
The information in this document is subject to change without notice and does not
represent a commitment on the part of the developer.
This document contains materials protected by copyright. All rights are reserved. No
part of this manual may be reproduced or transmitted in any form, by any means or
for purpose without express written consent.
Federal Communications Radio Frequency Interference Statement.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in accordance
with the instruction manual may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio of
television reception, which can be determined by turning the equipment off or on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Notice :
(1)
The changes or modifications not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
(2)
Shielded interface cables and AC power adapter, if any must be used in order
to comply with the emission limits.
CE DECLARATION
This device complies with CE class B.
*N50081-1 *EN50082-1
EN5022 *IEC 801-2
*IEC 801-3
*IEC 801-4
All trademarks are the property of their respective owner.
Printed in Taiwan R.O.C.
REV. A
Quick Installation Guide of Joymate
Joymate is a hand-size VIDEO TO VGA MONITOR converter box, it convert all video
signal in the world into non-interlace VGA signal for CRT monitors or LCD
monitor. OSD function and Remote controller make Joymate user-friendly. It is easily
connected to PC, video source, such as VCR, LD or VCD players and video game
machines without any software installation, just plug and display.
1. Features
Superior video quality
Plug and Display installation
Supports composite VIDEO and S-VIDEO and VGA input
Output to VGA monitor
Supports all video standard in the world, which include PAL BGHI / NTSC M,
NTSC4.43(50Hz) / PAL4.43(60Hz), PAL N / NTSC4.43(60Hz), NTSC N / PAL M
and SECAM video system
On Screen Display (OSD) function
Full function Remote controller
With Brightness, Contrast, Color, Hue control
0.6W (8 ohms) stereo power amplifier for LINE IN
Compact form factor : 95mm(L)x55mm(W)x30mm(H)
2. Package contents
1. Joymate converter box
2. Quick Installation Guide
3. VGA cable
4. Remote controller
5. AC adapter (6V, 300mA)
6. Battery (CR2025)
3. Minimum system requirement
VGA monitor (for NTSC: HSYNC=31.5KHz, VSYNC=60Hz,
PAL: HSYNC=31.25KHz, VSYNC=50Hz)
Video input device (e.g. VCR, V8, LD player, TV game machine and etc.)
Speaker with 4 ohms impedance
4. Installation
5. Connector and Button
1. VIDEO IN : Connect to VIDEO OUT of video source (e.g. VCR, V8
or TV GAME)
2. S-VIDEO IN : Connect to S-VIDEO OUT of video source
3. VGA IN : Connect to VGA card with supplied VGA cable
4. VGA OUT : Connect to your original VGA monitor
5. LINE IN : Stereo audio signal input, connect to AUDIO OUT of
audio source (e.g. VCR, V8 or TV GAME)
6. SPK : Stereo power amplifier output, connect 4 to 8 ohms
impedance speaker.
7. DC IN : Connect to supplied AC adapter.
8. PC/AV : Input source selection button, switch among VGA IN,
VIDEO IN and S-VIDEO IN.
9. IR : Infrared input of remote controller
6. Remote controller
1. PC : Switch to VGA IN
2. VIDEO : Switch to VIDEO IN
3. SVIDEO : Switch to S-VIDEO IN
4. OSD : On screen display button, display input signal status.
5. BRITE. : Brightness adjustment. Press this button then press “+”
or “-“ can increment or decrement the brightness level.
6. CONT. : Contrast adjustment. Press this button then press “+” or
“–“ can increment or decrement contrast level.
7. COLOR : Color adjustment. Press this button then press “+” or
“–“ can increment or decrement the color level.
8. HUE : Hue adjustment. Press this button then press “+” or
“–“ can increment or decrement the hue level.
9. SYSTEM : Video system selection button, press this button to
select one of PAL BGHI/NTSC M,
NSTC4.43(50Hz)/PAL4.43(60Hz),
PAL N/NTSC4.43(60Hz), NTSC N/PAL M or
SECAM/PAL4.43(60Hz)
10. RECALL : Reset the brightness, contrast, color and hue to factory
default setting.
VGA
MONITOR
PC
VCR
LD
TV GAME
VGA IN
VGA OUT
DC IN
LIN IN
SPK
S-VIDEO IN VIDEO IN
VIDEO
CABLE
AUDIO
CABLE
SPEAKER
Ac Adapter
VGA Cable
Loading...