grandimpianti 805898ENR1 Installation & Operation Manual
Stacked Washer/Dryers
SWD455C_SVG
Electric and Gas Models
Installation/Operation
Original Instructions
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 805898ENR1
February 2015
Front Matter
WARNING
Risk of fire. Highly flammable material.
W881
Front Matter
IMPORTANT: Purchaser must consult the local gas
supplier for suggested instructions to be followed if
the dryer user smells gas. The gas utility instructions
plus the SAFETY and WARNING note directly above
must be posted in a prominent location near the dryer
for customer use.
WARNING
Read all instructions before using unit.
WARNING
FOR YOUR SAFETY, the information in this manual
must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death.
W033
WARNING
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
• WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Clear the room, building or area of all occu-
pants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
• Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
W052
• Installation of unit must be performed by a qualified installer.
• Install clothes dryer according to manufacturer’s
instructions and local codes.
• DO NOT install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type)
duct is installed, it must be of a specific type
identified by the appliance manufacturer as suitable for use with clothes dryers. Refer to section
on connecting exhaust system. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
W729R1
WARNING
To reduce the risk of severe injury or death, follow
all installation instructions. Save these instructions.
W894
WARNING
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
W053
This product uses FreeRTOS V7.2.0 (www.freertos.org).
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
3 Part No. 805898ENR1
Table of Contents
Safety Information..................................................................................6
Explanation of Safety Messages....................................................................... 6
Important Safety Instructions........................................................................... 6
Important Safety Instructions........................................................................... 7
Dimensions............................................................................................. 9
Installation........................................................................................... 14
Before You Start...........................................................................................14
Tools........................................................................................................14
Central Pay Models................................................................................... 14
Order of Installation Steps..........................................................................14
Position Unit Near Installation Area............................................................... 15
Remove Shipping Materials........................................................................... 15
Connect Fill Hoses........................................................................................16
Water Supply Requirements....................................................................... 16
Model Numbers Ending in "06".................................................................. 16
All Other Models.......................................................................................17
Install Washer Electrical Cord........................................................................18
Non-Gravity Drain Models - Connect Drain Hose to Drain Receptacle.............. 19
Standpipe Installation................................................................................ 19
Gravity Drain Models - Connect Drain Outlet to Drain System......................... 20
Gas Dryers - Connect Gas Supply Pipe........................................................... 20
Connect Dryer Exhaust System...................................................................... 22
Exhaust Direction......................................................................................23
Exhaust System.........................................................................................23
Multi-Dryer Installation Exhaust Requirements............................................24
Position and Level the Unit............................................................................26
Wipe Out Inside of Washer and Dryer Drums..................................................27
Connect the Washer to Electrical Power..........................................................28
Washer Electrical Requirements................................................................. 28
Earth/Ground Instructions.......................................................................... 28
Connect the Dryer to Electrical Power............................................................ 29
Electrical Requirements............................................................................. 29
Earth/Ground and Wiring Instructions......................................................... 30
Check Installation......................................................................................... 30
Check Heat Source........................................................................................30
Electric Dryers.......................................................................................... 30
Gas Dryers................................................................................................30
Operation............................................................................................. 32
©
Published by permission of the copyright owner.
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
4 Part No. 805898ENR1
Operation Instructions for Washers.................................................................32
Load Laundry........................................................................................... 32
Close Loading Door...................................................................................32
Add Laundry Supplies............................................................................... 32
Determine Proper Controls.........................................................................33
Set Fabric Selector/Wash Temperature (°C).................................................33
Set Soil Level............................................................................................33
Insert Coins, if Needed...............................................................................33
Start Washer............................................................................................. 33
Indicator Lights.........................................................................................34
Operation Instructions for Dryers................................................................... 34
Clean Lint Filter........................................................................................34
Load Laundry........................................................................................... 35
Close Loading Door...................................................................................35
Determine Proper Controls.........................................................................35
Set Fabric Selector.....................................................................................35
Insert Coins, if Needed...............................................................................35
Start Dryer................................................................................................36
Remove Laundry.......................................................................................36
Indicator Lights.........................................................................................36
Maintenance......................................................................................... 37
User-Maintenance Instructions....................................................................... 37
Lubrication............................................................................................... 37
Cold Weather Care.................................................................................... 37
Extended Non-Use.................................................................................... 37
Care of Your Washer................................................................................. 37
Care of Your Dryer....................................................................................38
Reinstallation of Shipping Materials............................................................... 38
Motor Overload Protector.............................................................................. 39
For Energy Conservation............................................................................... 39
Troubleshooting....................................................................................40
Disposal of Unit.................................................................................... 44
Contact Information............................................................................. 45
Installer Checklist.................................................................................46
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
5 Part No. 805898ENR1
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,” and
“CAUTION”), followed by specific instructions, are found in this
manual and on machine decals. These precautions are intended
for the personal safety of the operator, user, servicer, and those
maintaining the machine.
Safety Information
WARNING
To reduce the risk of fire, electric shock, serious injury or death to persons when using your washer,
follow these basic precautions:
W023
DANGER
Indicates an imminently hazardous situation that, if
not avoided, will cause severe personal injury or
death.
WARNING
Indicates a hazardous situation that, if not avoided,
could cause severe personal injury or death.
CAUTION
Indicates a hazardous situation that, if not avoided,
may cause minor or moderate personal injury or
property damage.
Additional precautionary statements (“IMPORTANT” and
“NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor
machine damage will occur if the procedure is not followed.
NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related.
Important Safety Instructions
WASHER
Save These Instructions
• Read all instructions before using the washer.
• Install the washer according to the INSTALLATION INSTRUCTIONS. Refer to the EARTH/GROUND INSTRUCTIONS in the INSTALLATION manual for the proper earth/
ground connection of the washer. All connections for water,
drain, electrical power and earth/ground must comply with local codes and be made by licensed personnel when required.
Do not do it yourself.
• Do not install or store the washer where it will be exposed to
water and/or weather.
• Do not add the following substances or textiles containing
traces of the following substances to the wash water: gasoline,
kerosene, waxes, cooking oils, vegetable oils, machine oils,
dry-cleaning solvents, flammable chemicals, thinners or other
flammable or explosive substances. These substances give off
vapors that could ignite, explode or cause the fabric to catch
on fire by itself.
• Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using a
washing machine or combination washer-dryer, turn on all hot
water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. THE
GAS IS FLAMMABLE, DO NOT SMOKE OR USE AN
OPEN FLAME DURING THIS TIME.
• To reduce the risk of an electric shock or fire, DO NOT use
an extension cord or an adapter to connect the washer to the
electrical power source.
• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used
near children. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their
safety. This is a safety rule for all appliances.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Children less than three years should be kept away unless
continuously supervised.
• Do not reach into the washer if the washtub or agitator, if applicable, is moving.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
6 Part No. 805898ENR1
• Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT tamper with the controls or bypass any safety devices.
• Use your washer only for its intended purpose, washing
clothes. Always follow the fabric care instructions supplied
by the garment manufacturer.
• Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. To reduce the risk of poisoning or chemical burns, keep them out of the reach of children at all times (preferably in a locked cabinet). Heed all
warnings or precautions.
• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener
or product.
• Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.
• Keep your washer in good condition. Bumping or dropping
the washer can damage safety features. If this occurs, have
your washer checked by a qualified service person.
• Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions
that you understand and have the skills to carry out. ALWAYS disconnect the washer from electrical supply before
attempting any service.
• Disconnect the power cord by grasping the plug, not the cord.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
• Before the washer is removed from service or discarded, remove the lid or door to the washing compartment.
• Failure to install, maintain, and/or operate this washer according to the manufacturer’s instructions may result in conditions
which can produce bodily injury and/or property damage.
NOTE: The WARNING and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Common sense, caution and care must be exercised when installing, maintaining, or operating the
washer.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand.
Important Safety Instructions
DRYER
Save These Instructions
Safety Information
WARNING
To reduce the risk of fire, electric shock, serious injury or death to persons when using your dryer, follow these basic precautions:
W130
• Read all instructions before using the dryer.
• Install this dryer according to the INSTALLATION INSTRUCTIONS. Refer to the EARTH/GROUND INSTRUCTIONS in the INSTALLATION manual for the proper earth/
ground connection of the dryer. All connections for electrical
power, earth/ground and gas supply must comply with local
codes and be made by licensed personnel when required. Do
not do it yourself.
• Do not install or store the dryer where it will be exposed to
water and/or weather.
• Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline or machine
oils, vegetable or cooking oils, cleaning waxes or chemicals,
dry-cleaning solvents, thinner, anything containing chemicals
such as in mops and cleaning cloths, or other flammable or
explosive substances as they give off vapors that could ignite,
explode or cause fabric to catch on fire by itself.
• Items that have been soiled with substances such as cooking
oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers, should be washed in hot water
with an extra amount of detergent before being dried in the
tumble dryer.
• To reduce the risk of fire, DO NOT DRY plastics or articles
containing foam or latex rubber or similarly textured rubberlike materials, such as shower caps, water proof textiles, rubber-backed articles, and clothes or pillows filled with foam
rubber pads.
• Do not tumble fiberglass curtains and draperies unless the label says it can be done. If they are dried, wipe out the cylinder
with a damp cloth to remove particles of fiberglass.
• Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near
children. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning the use
of the appliance by a person responsible for their safety. This
is a safety rule for all appliances.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Children less than three years should be kept away unless
continuously supervised.
• Do not reach into the dryer if the cylinder is revolving.
• Use the dryer only for its intended purpose, drying clothes.
ALWAYS follow the fabric care instructions supplied by the
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
7 Part No. 805898ENR1
Safety Information
garment manufacturer and only use the dryer drum to dry textiles that have been washed in water.
• Always read and follow manufacturer’s instructions on packages of laundry and cleaning aids. Heed all warnings or precautions. To reduce the risk of poisoning or chemical burns,
keep them out of reach of children at all times (preferably in a
locked cabinet).
• Remove laundry immediately after the dryer stops.
• DO NOT operate the dryer if it is smoking, grinding or has
missing or broken parts or removed guards and/or panels. DO
NOT tamper with the controls or bypass any safety devices.
• DO NOT operate individual units if they have been separated
from a stack unit.
• Dryer will not operate with the loading door open. DO NOT
bypass the door safety switch by permitting the dryer to operate with the door open. The dryer will stop tumbling when the
door is opened. Do not use the dryer if it does not stop tumbling when the door is opened or starts tumbling without
pressing the START mechanism. Remove the dryer from use
and call the service person.
• ALWAYS clean the lint filter after every load. A layer of lint
in the filter reduces drying efficiency and prolongs drying
time. Keep area around the exhaust opening and adjacent surrounding area free from the accumulation of lint, dust and
dirt. The interior of the dryer and the exhaust duct should be
cleaned periodically by qualified service personnel.
• Do not repair or replace any part of the dryer, or attempt any
servicing unless specifically recommended in the user-maintenance instructions or in published user-repair instructions
that you understand and have the skills to carry out. ALWAYS disconnect the electrical power to the dryer before attempting service. Disconnect the power cord by grasping the
plug, not the cord.
• If supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Before the dryer is removed from service or discarded, remove the door to the drying compartment.
• Failure to install, maintain, and/or operate this machine according to the manufacturer’s instructions may result in conditions which can produce bodily injury and/or property damage.
NOTE: The WARNING and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Observe and be aware of other labels and precautions that are located on the machine. They are intended to provide instruction for safe use of the machine. Common sense, caution and care must be exercised when installing, maintaining, or operating the
dryer.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
8 Part No. 805898ENR1
Dimensions
SWD1023N_SVG
Q
P
O
N
I
M
L
K
J
H
G
F
E
D
C
B
A
The workstation average sound pressure level is 68.7 dBA.
Electric Models Equipped With Drain Hose
Dimensions
A * 1678 mm [66.06 in.]
B * 1447 mm [56.97 in.]
C 597 mm [23.5 in.]
D 213 mm [8.375 in.]
E 610 mm [24 in.]
F 203 mm [8 in.]
G 391 mm [15.4 in.]
H * 938 mm [36.9 in.]
I * 368 mm [14.5 in.]
J * 813 mm [32 in.]
K 683 mm [26.875 in.]
L * 1986 mm [78.17 in.]
M * 1184 mm [46.62 in.]
N 52 mm [2.04 in.]
O 704 mm [27.73 in.]
P 38 mm [1.5 in.]
Q * 333 mm [13.1 in.]
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
* With leveling legs turned into base.
9 Part No. 805898ENR1
SWD1024N_SVG
Q
S
PR
O
N
M
L
I
K
J
H
G
F
E
D
C
B
A
1
Dimensions
Gas Models Equipped With Drain Hose
1. 3/8 in. NPT Gas Connection
A *1678 mm [66.06 in.]
B *1447 mm [56.97 in.]
C 597 mm [23.5 in.]
D 213 mm [8.375 in.]
E 610 mm [24 in.]
F 203 mm [8 in.]
G 391 mm [15.4 in.]
H 59 mm [2.3 in.]
I *938 mm [36.9 in.]
J *368 mm [14.5 in.]
K *1140 mm [44.87 in.]
L *813 mm [32 in.]
M 683 mm [26.875 in.]
N *1986 mm [78.17 in.]
O *1184 mm [46.62 in.]
P 52 mm [2.04 in.]
Q 704 mm [27.73 in.]
R 38 mm [1.5 in.]
S *333 mm [13.1 in.]
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
* With leveling legs turned into base.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
10 Part No. 805898ENR1
Electric Models Equipped With Gravity Drain
SWD1027N_SVG
Q
S
P
R
O
N
M
L
I
K
J
H
G
F
E
D
C
B
A
1
1. 38 mm [1.5 in.] Inside Diameter; 47 mm [1.86 in.] Outside Diameter
Dimensions
A *1678 mm [66.06 in.]
B *1447 mm [57.97 in.]
C 597 mm [23.5 in.]
D 213 mm [8.375 in.]
E 610 mm [24 in.]
F 203 mm [8 in.]
G 391 mm [15.4 in.]
H *938 mm [36.9 in.]
I *368 mm [14.5 in.]
J *813 mm [32 in.]
K 683 mm [26.875 in.]
L 107 mm [4.2 in.]
M *104 mm [4.1 in.]
N *1184 mm [46.62 in.]
O *1986 mm [78.17 in.]
P 52 mm [2.04 in.]
Q 704 mm [27.73 in.]
R 38 mm [1.5 in.]
S *333 mm [13.1 in.]
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
* With leveling legs turned into base.
11 Part No. 805898ENR1
SWD1028N_SVG
Q
U
S
P
R
T
O
N
M
L
I
K
J
H
G
F
E
D
C
B
A
1
2
Dimensions
Gas Models Equipped With Gravity Drain
1. 3/8 in. NPT Gas Connection
2. 38 mm [1.5 in.] Inside Diameter; 47 mm [1.86 in.] Outside Diameter
A *1678 mm [66.06 in.]
B *1447 mm [56.97 in.]
C 597 mm [23.5 in.]
D 213 mm [8.375 in.]
E 610 mm [24 in.]
F 203 mm [8 in.]
G 391 mm [15.4 in.]
H 60 mm [2.3 in.]
I *938 mm [36.9 in.]
J *368 mm [14.5 in.]
K *1140 mm [44.87 in.]
L *813 mm [32 in.]
M 683 mm [26.875 in.]
N 107 mm [4.2 in.]
O *104 mm [4.1 in.]
P *1184 mm [46.62 in.]
Q *1986 mm [78.17 in.]
R 52 mm [2.04 in.]
S 704 mm [27.73 in.]
Table continues...
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
12 Part No. 805898ENR1
T 38 mm [1.5 in.]
U *333 mm [13.1 in.]
Dimensions
NOTE: Exhaust openings are 102 mm [4 inch] metal
ducting.
NOTE: Gas models cannot be vented out left side of
cabinet because of burner housing.
IMPORTANT: The dryer should have sufficient clearance around it for needed ventilation and for the ease
of installation and servicing. For maximum drying performance, we recommend that more clearance be allowed around the dryer than the clearances that are listed throughout this manual.
* With leveling legs turned into base.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
13 Part No. 805898ENR1
Before You Start
SWD1021N_SVG
11
10
9
8
4
3
2
1
6
7
5
SWD990N_SVG
Tools
For most installations, the basic tools you will need are:
Installation
Installation
WARNING
Any disassembly requiring the use of tools must be
performed by a suitably qualified service person.
W299
Central Pay Models
The machine is shipped from the factory with the Electronic Control Diagnostic Harness Assembly unplugged. To avoid unauthorized manual programming or vending, perform the following
steps.
1. Open control panel. Refer to Figure 2 .
2. Locate diagnostic harness on electronic control.
3. Plug connectors for “white/black” wire and “red/blue” wire
together.
1. Wrench
2. 1/4 inch Driver
3. Screwdriver
4. Level
5. Wood Block
6. Pliers
7. 5/16 Inch Socket Wrench
8. Gloves
9. Teflon Tape (Gas Models)
10. Duct Tape
11. Safety Glasses
Figure 1
NOTE: An 20.32 cm [8 in.] coin drawer is required for
coin operated models.
NOTE: If the unit is delivered on a cold day (below
freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until
the unit has had a chance to warm up.
NOTE: Some moisture in the wash drum is normal. Water is used during testing at the manufacturer.
NOTE: This appliance is suitable for use in countries
having a warm, damp climate.
1. Control Panel
Figure 2
Order of Installation Steps
The proper order of steps must be followed to ensure correct installation. Refer to the list below when installing your unit.
1. Position unit near area of installation.
2. Remove the shipping materials.
3. Connect the fill hoses.
4. Install the washer's electrical cord.
5. For non-gravity drain models, connect the drain hose to the
drain receptacle.
6. For gravity drain models, connect the drain outlet to the drain
system.
7. For gas models only, connect the gas supply pipe. Check for
gas leaks.
8. Connect dryer to exhaust system.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
14 Part No. 805898ENR1
9. Position and level the unit.
FLW2378N_SVG
FLW2296N_SVG1
FLW2297N_SVG1
FLW2358N_SVG
10. Wipe out inside of washer and dryer drums.
11. Connect the washer and dryer to electrical power.
12. Recheck steps.
13. Start and run the dryer in a heat setting to verify dryer is heat-
ing.
Position Unit Near Installation Area
Move unit so that it is within 1.2 meters [4 feet] of the desired
area of installation.
CAUTION
Installation
Washer and dryer are not designed to be operated as
separated, side-by-side units.
NOTE: For best performance and to minimize vibration
or movement, install washer on a solid, sturdy and level floor. Some floors may need to be reinforced, especially on a second floor or over a basement. Do not install the washer on carpeting, soft tile or other weakly
supported structures.
Remove Shipping Materials
1. Remove two screws at bottom of front access panel. Rotate
bottom of panel out and remove panel.
W187
Figure 4
4. Go to rear of washer and pull label from rear shipping bolts.
5. Remove two 9/16 inch bolts. Unscrew each bolt while apply-
ing forward pressure just until bolt stops unthreading. Work
each bolt and spacer out by hand using a circular motion.
NOTE: Avoid backing bolts out completely or
spacers might fall into cabinet.
Figure 5
6. Insert two plugs included in accessories bag into rear shipping
bolt holes.
Figure 3
2. Remove two 9/16 inch bolts and washers holding shipping
brace to weight.
3. Remove two 9/16 inch bolts and washers holding shipping
brace to washer base and remove brace.
©
Published by permission of the copyright owner -
DO NOT COPY or TRANSMIT
Figure 6
7. Replace front access panel.
15 Part No. 805898ENR1
Loading...