Grand Hall 7001a Owner's Manual
Covered Cooker Barbecue
Operating and Assembly Instructions
FOR YOUR SAFETY.
IF YOU SMELL GAS:
1. Shut off gas to the
appliance, if possible.
2. Extinguish any open flame.
3. Open hood.
4. If odour continues,
immediately call your gas
supplier or fire department.
FOR YOUR SAFETY.
1. Do not store or use
petrol or other flammable
vapours and liquids in the
vicinity of this or any other
appliance.
2. A gas cylinder not
connected for use must not
be stored in the vicinity of
this or any other appliance.
These instructions are a
guide to assembling and
using the 7001A-HN
barbecue.
Please read carefully, and
retain for future reference.
Only to be used outdoors.
Illustration may vary from barbecue
contained in carton.
2
GENERAL INFORMATION
2
TABLE OF CONTENTS
General Information 2
Safety 3-4
Outdoor Areas 5
Pre-Assembly 6
Assembly 7-9
Assembly – General 10-12
Operation 13-14
Fault Finding 15
Maintenance 16-18
Parts Diagram / List 20-21
FOR CUSTOMER REFERENCE
(Record and file in a safe place)
Purchased from
Date purchased
Serial No.
NOTE:
Sales docket must be kept as proof of purchase date
Barbecues for use with bottled gas are labelled ‘Universal LPG’ or
‘Propane’. Barbecues for use with natural gas are labelled ‘Natural Gas’ and
must be installed by an authorised person. Check the gas type sticker
attached to the barbecue. Check that the label matches the gas type to be
used.
Your barbecue is preset at the factory to operate on bottled gas
only, unless specified otherwise.
• FAILURE TO COMPLY WITH THESE
INSTRUCTIONS COULD RESULT IN A
FIRE OR EXPLOSION WHICH COULD
CAUSE SERIOUS BODILY INJURY,
DEATH OR PROPERTY DAMAGE
• ACCESSIBLE PARTS MAY BE
VERY HOT
• KEEP YOUNG CHILDREN AWAY
• ANY MODIFICATION OF THIS
APPLIANCE MAY BE DANGEROUS
• DO NOT MOVE THIS APPLIANCE
DURING USE
• TURN OFF THE GAS SUPPLY AT THE
GAS CYLINDER AFTER USE
• READ THE INSTRUCTIONS BEFORE
USING THE APPLIANCE
• PARTS SEALED BY THE
MANUFACTURER MUST NOT BE
ALTERED IN ANY WAY
• THIS BARBECUE IS ONLY TO BE
USED OUTDOORS.
CLEARANCES
The following minimum clearances from combustible materials must be
maintained when barbecue is in use:
top – 1000 mm, rear – 450 mm, sides – 250 mm.
Openings at the rear and sides of the appliance provide air for
combustion and must not be obstructed.
HOSE AND REGULATOR SAFETY
NEVER OPERATE THIS BARBECUE
WITHOUT A REGULATOR.
The regulator and hose assembly supplied with the barbecue are suitable
for use with bottled gas.
This regulator is adjusted to have an outlet pressure of 2.75 kPa for
connection to a gas cylinder only. The regulator and hose assembly
supplied with the appliance must be used. Replacement regulator and
hose assemblies must be those specified by the appliance manufacturer.
When connecting the hose and regulator assembly to the gas
cylinder, take care to avoid unnecessary twisting of the flexible hose.
Also, take care to avoid a loose connection with the gas cylinder. After
the assembly has been secured, turn on the gas and check for leaks by
brushing a soap and water solution over all visible and accessible gas
line connections. Include checking those connections which were made
by your supplier. The presence of bubbles will indicate a gas escape. DO
NOT TEST FOR GAS ESCAPES WITH AN OPEN FLAME. If you are
unable to correct the leak by tightening the connections, turn off the
gas and contact your place of purchase immediately.
Always ensure the appliance is kept away from flammable materials
and the gas cylinder clear of any heat source. When changing over from
an empty gas cylinder to a full one, make sure this procedure is carried
out in a flame free atmosphere.
Inspect the gas hose assembly when exchanging the gas cylinder,
or at least once a year, whichever is more frequent. If the ‘O-Ring’ or PVC
hose is cracked, cut, abraded or damaged in any way, the appliance must
not be operated. The complete assembly must be replaced if damaged
and when statutory conditions require it. Contact your place of purchase
if uncertain.
OVERALL DIMENSIONS
Height – hood closed 1125 mm, hood open 1490 mm
Width (including trolley) – 1610 mm
Depth – hood closed 690 mm, hood open 815 mm
GAS INSTALLATION CODES
This appliance is certified to AS 4557 by the Australian Gas Association.
Refer data label on the barbecue for certificate number.
Barbecues must be used in accordance with the installation
requirements of your local gas supply authority, and the appropriate
installation standard AS5601.
SPECIFICATIONS
Appliance specifications can be found on the data label attached to the
side panel of the barbecue body.
3
SAFETY
3
READ CAREFULLY BEFORE
ASSEMBLING AND OPERATING
YOUR BARBECUE.
FOR YOUR SAFETY:
• DO NOT STORE OR USE PETROL OR
OTHER FLAMMABLE VAPOURS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE
• DO NOT STORE EMPTY OR FULL SPARE
GAS CYLINDERS UNDER OR NEAR THIS
OR ANY OTHER APPLIANCE
• KEEP THE GAS HOSE AWAY FROM HOT
SURFACES. PROTECT GAS HOSE FROM
DRIPPING GREASE.
AVOID UNNECESSARY TWISTING OF
HOSE. VISUALLY INSPECT HOSE PRIOR TO
EACH USE FOR CUTS, CRACKS,
EXCESSIVE WEAR OR OTHER DAMAGE.
REPLACE HOSE, IF NECESSARY
• NEVER TEST FOR GAS LEAKS WITH A LIT
MATCH OR OPEN FLAME
• NEVER LIGHT BARBECUE WITH LID ON OR
HOOD CLOSED
• NEVER LEAN OVER COOKING SURFACE
WHILE LIGHTING BARBECUE
• USE GOOD QUALITY INSULATED OVEN
MITTS WHEN OPERATING BARBECUE
• NEVER ALTER OR MODIFY THE
REGULATOR OR GAS SUPPLY ASSEMBLY
• THIS BARBECUE MUST NOT BE USED
INDOORS.
CHECKING FOR GAS LEAKS
NEVER TEST FOR LEAKS WITH A FLAME.
Prior to first use, and at the beginning of each new season (or, if
using bottled gas, whenever gas cylinder is changed), you must check
for gas leaks. Follow these steps:
1. Make soap solution by mixing one part liquid detergent and one
part water.
2. Turn burner control(s) to
3. Apply the soap solution to all visible and accessible gas connections
including the gas cylinder. Bubbles will appear in the soap solution
if connections are not properly sealed. Tighten or rectify as necessary.
Refer to page 4 for further details.
4. If you have a gas leak you cannot rectify, turn off the gas at the
source. Contact the manufacturer for assistance.
Refer to back cover.
‘OFF’, then turn on gas at source.
GAS CYLINDER USE & SAFETY
This is a low pressure barbecue and must only be used with the hose and
regulator supplied.
Your barbecue is designed for use with a 9 kg gas cylinder. Ensure
gas cylinder conforms to Australian Standards and is less than 10 years
old.
DO NOT CONNECT YOUR BARBECUE TO A GAS
CYLINDER LESS THAN OR EXCEEDING THIS CAPACITY.
NEVER CONNECT AN UNREGULATED
GAS CYLINDER TO YOUR BARBECUE.
LOCATION OF YOUR BARBECUE
DO NOT use your barbecue in garages, porches, breezeways, sheds or
other enclosed areas. Your barbecue is to be used OUTDOORS ONLY.
Refer to page 5. The barbecue is not intended to be installed in or used
on recreational vehicles and/or boats and should not be placed under
any surface that will burn. Do not obstruct the flow of combustion and
ventilation air around the barbecue housing while in use.
SERVICING
ANY OF THE FOLLOWING SIGNS MAY INDICATE THAT THE APPLIANCE IS
NOT OPERATING PROPERLY AND MAY NEED
SERVICING:
• EXCESSIVE YELLOW FLAME
• IRREGULAR SIZE OF FLAME
ACROSS BURNER
• ‘POPPING’ OF FLAME
• SOOTING
• ABNORMAL NOISE(S)
• HISSING SOUND
Before requesting service,
NOTE:
please refer to page 15 ‘Fault finding’.
PROTECT CHILDREN
Keep children away from barbecue during use and until barbecue has
cooled after you are finished. Do not allow children to operate barbecue
or to swing on handle.
The gas cylinder should be filled by a reputable gas dealer, or exchanged
at a reputable gas cylinder exchange outlet. Gas cylinders should be
visually inspected and re-qualified periodically.
Always keep gas cylinder in an upright position. Always close the
cylinder valve when the barbecue is not in use.
Do not subject the gas cylinder to excessive heat.
• NEVER STORE YOUR
GAS CYLINDER INDOORS
• FOR STORAGE AND CYLINDER
EXCHANGE, DISCONNECT HOSE AT THE
CYLINDER ONLY –
DO NOT DISCONNECT HOSE FROM
THE APPLIANCE
If you store your barbecue indoors, ALWAYS disconnect and remove gas
cylinder FIRST, and store gas cylinder safely outside. Gas cylinders
must be stored outdoors in a well ventilated area out of reach of children,
and must not be stored in a building, garage or any other enclosed area.
DANGER – IF YOU SMELL OR HEAR
THE HISS OF ESCAPING GAS FROM
THE GAS CYLINDER:
• KEEP CLEAR OF THE GAS CYLINDER
• TURN ALL CONTROLS ON THE BARBECUE
TO ‘OFF’
EXTINGUISH ANY OPEN FLAME
•
REMOVE LID OR OPEN HOOD
•
IF ODOUR CONTINUES, IMMEDIATELY
•
CALL YOUR GAS SUPPLIER OR FIRE
DEPARTMENT.
4
SAFETY
ALWAYS CHECK FOR GAS LEAKS
EACH TIME YOU USE YOUR BARBECUE
You should follow this procedure after any of the following:
• Not having used the barbecue for an extended period of time
• Initial assembly of barbecue
• Any disconnection and reconnection of hose assembly
• Changing gas cylinder
• Upon re-connecting gas cylinder after it has been disconnected for storage.
4
CHECKING FOR GAS LEAKS
NEVER CHECK FOR LEAKS WITH
A FLAME.
1. Make liquid detergent solution by mixing one (1) part liquid
detergent and four (4) parts water.
4 parts water
1 part liquid
detergent
2. Turn burner control knob(s) to ‘OFF’, then turn on gas at
source.
Open
3. Apply the liquid detergent solution to all visible and
accessible gas connections, including the connection to
the gas cylinder. Bubbles will appear in the liquid detergent
solution if connections are not properly sealed. Tighten or
rectify as necessary.
IF YOU HAVE A GAS LEAK YOU
CANNOT RECTIFY, TURN OFF THE GAS
AT THE SOURCE. CONTACT THE
MANUFACTURER.
5
THIS APPLIANCE SHALL ONLY BE USED IN AN ABOVE GROUND OPEN AIR SITUATION WITH NATURAL
VENTILATION, WITHOUT STAGNANT AREAS, WHERE GAS LEAKAGE AND PRODUCTS OF COMBUSTION
ARE RAPIDLY DISPERSED BY WIND AND NATURAL CONVECTION.
ANY ENCLOSURE IN WHICH THE APPLIANCE IS USED SHALL COMPLY WITH ONE OF THE FOLLOWING:
• AN ENCLOSURE WITH WALLS
ON ALL SIDES, BUT AT LEAST
ONE PERMANENT OPENING AT
GROUND LEVEL AND NO
OVERHEAD COVER
• WITHIN A PARTIAL
ENCLOSURE THAT INCLUDES
AN OVERHEAD COVER AND NO
MORE THAN TWO WALLS
• WITHIN A PARTIAL
ENCLOSURE THAT INCLUDES
AN OVERHEAD COVER AND
MORE THAN TWO WALLS, THE
FOLLOWING SHALL APPLY:
OUTDOOR AREAS
(i) AT LEAST 25% OF THE TOTAL
WALL AREA IS
COMPLETELY OPEN: AND
(ii) AT LEAST 30% OF THE
REMAINING WALL AREA IS
OPEN AND UNRESTRICTED
• IN THE CASE OF BALCONIES,
AT LEAST 20% OF THE TOTAL
OF THE SIDE, BACK AND FRONT
WALL AREAS SHALL BE AND
REMAIN OPEN AND
UNRESTRICTED
• DO NOT USE YOUR BARBECUE
IN GARAGES, PORCHES,
BREEZEWAYS, SHEDS OR
OTHER ENCLOSED AREAS.
YOUR BARBECUE IS TO BE
USED OUTDOORS ONLY.
Refer below
• THE BARBECUE IS NOT
INTENDED TO BE INSTALLED IN
OR USED ON RECREATIONAL
VEHICLES AND/OR BOATS AND
SHOULD NOT BE PLACED
ADJACENT TO OR UNDER ANY
SURFACE THAT WILL BURN
• DO NOT OBSTRUCT THE FLOW
OF COMBUSTION AND
VENTILATION AIR AROUND
THE BARBECUE HOUSING
WHILST IN USE.
5
The following diagrams are examples of outdoor areas.
These same principles apply to canopy or shaded cloth areas.
Both ends
open
Open side at
least 25% of total
wall area
30% or more in total of
the remaining wall area
is open and unrestricted
30% or more in total of
the remaining wall area
is open and unrestricted
Open side at
least 25% of total
wall area
6
PRE-ASSEMBLY
6
GENERAL
While it is possible for one person to assemble the barbecue,
we recommend asking for the assistance of another person when
manoeuvring some of the larger or heavier pieces.
ASSEMBLY TIPS
1. Flatten cardboard packaging and use this as a protective
work surface to assemble upon.
2. Some protective coating may need to be removed from
components prior to assembly.
3. Do not tighten screws and nuts until trolley is fully assembled.
4. Pre-screwing of connection points for securing the side
shelves will assist in securing shelves smoothly.
CHECK BARBECUE FOR ANY DAMAGE
Before attempting to assemble your barbecue, check that all the
necessary parts have been included using the parts list opposite.
Inspect barbecue and trolley parts as you proceed.
Contact your place of purchase for assistance regarding
replacement of any damaged or missing parts. Supplier contact
details are on the back cover of the instruction manual.
Do not assemble or operate a barbecue that appears
damaged.
Check that the barbecue supplied is correct for the gas type
being used. There is a label on the side panel of the barbecue
above the gas connection. Barbecues for use with gas cylinders
are labelled
are labelled
‘Universal LPG’. Barbecues for use with natural gas
‘Natural Gas’.
CARTON CONTENTS
BARBECUE COMPONENTS:
1 Barbecue body with 4 burners attached.
1 Grease draining tray.
1 Grease receptacle.
2 Flame tamer plates.
1 Cast iron solid & 1 slotted grill plate.
1 Warming rack.
1 Hardware pack.
TROLLEY COMPONENTS:
4 Legs.
2 Side panels.
1 Gas cylinder hook.
1 Gas cylinder support.
2 Wheels with hubcaps.
2 Castors.
1 Rear panel.
1 Bottom wire base tray.
1 Door bracket
1 Door bracket – bottom.
2 Doors.
1 Side shelf.
1 Side burner shelf
2 Shelf brackets.
2 Towel rails.
– top.
(regulator and side burner attached).
TOOLS YOU WILL NEED
Standard Phillips-head screwdriver.
Adjustable spanner (open end shifter).
HOSE CONNECTIONS
Hose connection threads are of the following form:
5
/8" - 18 UNF (3/8" - SAE flare).
Do not use sealing tape or compounds. Gas seal is metal
to metal flared surfaces.
NOTE: Components may be packed in Head or
Trolley cartons. Completely unpack both cartons
and check for correct quantities before assembly.
7
ASSEMBLY
NOTE: Do not tighten screws / nuts unless specified.
7
Attach trolley legs, side panel and base tray. Do not
1
overtighten dome nuts.
A
Phillips-head screw 3/16" x 3/8" Qty: 8
B
Dome nut 5/16"
Qty: 4
Attach trolley rear panel and bottom bracket.
2
A
A
B
B
B
B
A
Phillips-head screw 3/16" x 3/8" Qty: 4
Phillips-head screw 1/4" x 23/4"
Qty: 4
Attach wheels and castors.
3
Axle bolt
3
/8" x 35/16"
B
Split washer
B
3
/8"
Nylon lock nut
3
/8"
8
Attach bowl decoration brackets.
4
ASSEMBLY
Refer Note.
LEFT
8
NOTE: Flange is to face
away from barbecue
body.
Phillips-head screw 1/4" x 1/2"
Qty: 8
NOTE: The holes in the top face of the bracket are
for mounting accessory rotisserie brackets. These
holes are offset from the centre and the brackets
must be carefully attached to the left and right
sides. When corrected attached, the distance from
the rear hole to the rear of the barbecue is about
180 mm.
Attach gas cylinder hook and support.
5
Phillips-head screw 1/4" x 1/2"
Qty: 4
RIGHT
LEFT
SIDE
RIGHT
SIDE
Flange nut 1/4"
Qty: 2
Attach barbecue head to trolley.
6
NOTE:
Lay trolley carefully onto its back with the 8"
wheels to the left side.
Insert screw at positions ‘2’ and ‘4’.
Phillips-head screw 1/4" x 23/4"
Qty: 8
Nut pre-welded
Flange nut 1/4"
Qty: 6
inside
Nut pre-welded
Nut pre-welded
2
1
4
3
inside
Barbecue
body
inside
Loading...